###############################################################################
#Board Varaints and Versions are defined below:
#BOARD_VARIANT_NXPREF    0x01
#BOARD_NXPREF_VERSIONS(0x01, 0x02)

#BOARD_VARIANT_CUSTREF1  0x2A
#BOARD_CUSTREF1_VERSIONS(0x01,0x02,0x03)

UWB_BOARD_VARIANT_CONFIG=0x01
UWB_BOARD_VARIANT_VERSION=0x01

###############################################################################
#                          Extended CofigID
#DELAY_CALIBRATION_VALUE    E400
#AOA_CALIBRATION_CTRL       E401
#DPD_WAKEUP_SRC             E402
#WTX_COUNT_CONFIG           E403
#DPD_ENTRY_TIMEOUT          E404
#WIFI_COEX_FEATURE          E405
  ##Note: WIFI COEX CONFIG Disabled by default, if required add the
  ##      config (E4, 05, 04, 00, 3C, 1E, 1E) and update the
  ##      Lentgh and number of parameter accordingly in the header part.
  ##      WIFI COEX feature supports only in user binary.
#GPIO_USAGE_CONFIG          E408
  ##Note: Configure the GPIO for multiple purposes depending on usecase ID
  ##      config(E4, 08, 03, 00, 00, 00)
  ##      Length and number of parameter accordingly in the header part.
#CLK_CONFIG_CTRL            E430
  ##Note: Config for clock source selection and refer UCI specification
  ##      for more information.
#UWB_WLAN_5GHZ_CHANNEL_INTERFERENCE_LIST  E432
  ##Note: List of problematic channels in 5GHz Range, if required add
  ##      config (E4, 32, 03, 120, 124, 128) and update the
  ##      Length and number of parameters accordingly in header part.
#TX_PULSE_SHAPE_CONFIG      E428
# Refer the NXP UCI specification for below configs
#ANTENNA_RX_IDX_DEFINE   E460
#ANTENNA_TX_IDX_DEFINE   E461

UWB_CORE_EXT_DEVICE_DEFAULT_CONFIG={20, 04, 00, 24, 05,
    E4, 03, 01, b4,
    E4, 04, 02, f4, 01,
    E4, 28, 04, 02, 02, 02, 00,
    E4, 60, 07, 01, 01, 02, 01, 00, 01, 00,
    E4, 61, 06, 01, 01, 01, 00, 00, 00
}

##Note: Session specific default app config configured here
#ANTENNAS_CONFIGURATION_RX

NXP_UWB_EXT_APP_DEFAULT_CONFIG={01, 03, 03, 01, 01, 01}

##Note: Below configs are applicable in User_Mode FW only
##Note: WIFI COEX CONFIG Disabled by default, if required add the
  ##      config (E4, 05, 04, 00, 3C, 1E, 1E) and update the
  ##      Lentgh and number of parameter accordingly in the header part.
  ##      WIFI COEX feature supports only in user binary.
#WIFI_COEX_UART_USER_CFG E437
  ## UART based WiFi-CoEx Interface User Configuration. default value 0
#FREQ_OF_UWB_REQ_WLAN_CHANNEL_INFO E439
  ## Configure the frequency of UWB Requests to WLAN for getting WLAN Channel Information. Default value 3
  ## if required add the
  ##      config (E4, 39, 01, 03) and update the
  ##      Length and number of parameter accordingly in the header part
#GPIO_USAGE_CONFIG E4 08
  ## Customer need to set the DPD_WAKEUP_SOURCE as 02 (GPIO1) before applying the GPIO_USAGE_CONFIG command to
  ## enable time sync notification feature
UWB_USER_FW_BOOT_MODE_CONFIG={20, 04, 00, 12, 03,
    E4, 05, 04, 00, 3C, 1E, 1E,
    E4, 02, 01, 00,
    E4, 08, 03, 00, 00, 00
}

#LIST OF UWB CAPABILITY INFO NOT RECEIVED FROM UWBS
# mapping device caps according to Fira 2.0
# TODO: Remove once FW support available
UWB_VENDOR_CAPABILITY={ A7, 04, 01, 00, 00, 00,
  A8, 04, 05, 00, 00, 00,
  E3, 01, 01,
  E4, 04, 64, 00, 00, 00,
  E5, 04, 03, 00, 00, 00,
  E6, 01, 01,
  E7, 01, 01,
  E8, 04, B0, 04, 00, 00,
  E9, 04, 05, 00, 00, 00,
  EA, 02, 09, 00
}

###############################################################################
# Helios PROD Mode FW version
# Make sure you push the Production FW while using this Macro
NXP_UWB_PROD_FW_FILENAME="libsr100t_prod_fw.bin"

# Helios Dev Mode FW version
# Make sure you push the Dev Mode FW while using this Macro
NXP_UWB_DEV_FW_FILENAME="libsr100t_dev_fw.bin"
###############################################################################

###############################################################################
#enable or disable fw download logging
UWB_FW_DOWNLOAD_LOG=0x00
###############################################################################

###############################################################################
# set Crystal calibration settings
# byte[0] No Of registers
# byte[2-1] 38.4 MHz XTAL CAP1
# byte[4-3] 38.4 MHz XTAL CAP2
# byte[6-5] 38.4 MHz XTAL GM

# NXP_UWB_XTAL_38MHZ_CONFIG={2F, 21, 00, 0A, 05, 01, 07, 03, 0F, 00, 0F, 00, 21, 00}

###############################################################################
# This config enable/disable the Vendor extended notifications
# 00 for disable
# 01 for enable
NXP_UWB_EXTENDED_NTF_CONFIG={20, 04, 00, 05, 01, E4, 33, 01, 01}

###############################################################################
###############################################################################
# Core Device configurations
# Below sections needs to be updated with the correct values for needed core device configurations

#NXP_CORE_CONF_BLK_1={}

#NXP_CORE_CONF_BLK_2={}

#NXP_CORE_CONF_BLK_3={}

#NXP_CORE_CONF_BLK_4={}

#NXP_CORE_CONF_BLK_5={}

#NXP_CORE_CONF_BLK_6={}

#NXP_CORE_CONF_BLK_7={}

#NXP_CORE_CONF_BLK_8={}

#NXP_CORE_CONF_BLK_9={}

#NXP_CORE_CONF_BLK_10={}


NXP_LOG_JNI_LOGLEVEL=0x05
NXP_LOG_UCI_CORE_LOGLEVEL=0x05
NXP_LOG_UCIHAL_LOGLEVEL=0x05
NXP_LOG_FWDNLD_LOGLEVEL=0x05
NXP_LOG_TML_LOGLEVEL=0x05
NXP_LOG_UCIX_LOGLEVEL=0x05
NXP_LOG_UCIR_LOGLEVEL=0x05