# BetoCQ test suite release history

## 2.3 (05/28/2024)

## New
* Skip test if wifi_chipset is empty.
* Add MCC Aware test case with STAs connected to 2G/5G.
* Make connection, advertising/discovery mediums configurable.
* Allow the two devices connect to different SSIDs.
* Raise NC speed bar back to 40MB/s except for WLAN.
* Generate per-test openwrt syslog.
* Add 3p api function into nearby_connections_function_test.py.
* Report the suite name to the test summary.
* Enable individual test selection from the command-line.

### Bug fixes
* Add 10s delay after sta connection to allow scan, DHCP and internet
  validation to complete.
* Fix the bug that it can not run the test cases of eSIM and Quick Share.
* Clarify the failure reasons for some test failures.
* Fix the issue that wlan1 is not correctly detected.
* Fix the timestamp in failed iteration logs.
* Reduce wait time between iteration from 13s to 3s.

## 2.2 (05/10/2024)

## New
* Add iperf test for Aware, hotspot modes.
* Disable WLAN deny list so that the past failure won't affect the new runs.
* Add the key test info in test summary.
* Add the STA and medium info of failed iterations.
* Add P2P frequency check for MCC test cases.
* Add more failure triage tips.

### Bug fixes
* Improve the format of common triaging tips.
* Don't check max link speed for the disconnection check.
* Fix the format of triaging tips.
* Fix the control in test config.
* Fall back to use "adb shell cmd wifi status" when wifiGetConnectionInfo() fails.

## 2.1 (05/02/2024)

## New
* Add iperf test for WFD mode. iperf test speed requirement is 40MB/s while Nearby
  Connections speed requirement is 20MB/s in 2-stream 80MHz mode.
* Add the BT coex performance test.
* Add the support of BLE scan throttling during 2G transfer (enabled by default)
* Change the success rate target to 98%.
* Add Aware test case and enable it for QuickShare CUJ.
* Enable scc_2g_wfd_sta_tests for all devices.

### Bug fixes
* Fix the missing data of failed test cases by replacing all "sponge_properties"
  with "properties".
* Remove the unnecessary flag overriding and rely on the production config instead.
* Add the check of AP connection. If AP is disconnected or connect to a wrong
  frequency on the target side, mark the test as failed.
* Consolidate AP connection and speed check codes to one function.
* Add P2P frequency check for WFD/HS SCC test cases.
* Reduce 2G speed check from 3 to 1 MB/s until it is improved in NC.
* Remove AP frequency check for the test cases with empty wifi_ssid.
* Fix typo in DFS test cases and reduce BT transfer size by 50%.
* Skip p2p frequency check if wifi speed check is disabled or it is a DBS test.
* Add the method overriding annotation.
* Add more triaging tips for AP disconnected, wrong AP frequency and P2P/STA
  frequency mismatch cases.

## 2.0 (04/10/2024)

### New
* BetoCQ test suite: improved test coverage with the right quality bar taking into
  device capabilities
  * CUJ tests: Connectivity performance evaluation for the specific CUJs, such
  as Quickstart, Quickshare, etc.
  * Directed tests: Performance test with fixed D2D medium.
  * Function tests: Tests for the basic functions used by D2D connection.

## 1.6

### New
* `nearby_share_stress_test.py` for testing Nearby Share using Wifi only.

### Fixes
* Change discovery medium to BLE only.
* Increase 1G file transfer timeout to 400s.
* Disable GMS auto-updates for the duration of the test.

## 1.5

### New
* `esim_transfer_stress_test.py` for testing eSIM transfer using Bluetooth only.
* `quick_start_stress_test.py` for testing the Quickstart flow using both
   Bluetooth and Wifi.