/****************************************************************************** * * Copyright (c) 2014 The Android Open Source Project * Copyright (C) 1999-2012 Broadcom Corporation * * Licensed under the Apache License, Version 2.0 (the "License"); * you may not use this file except in compliance with the License. * You may obtain a copy of the License at: * * http://www.apache.org/licenses/LICENSE-2.0 * * Unless required by applicable law or agreed to in writing, software * distributed under the License is distributed on an "AS IS" BASIS, * WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied. * See the License for the specific language governing permissions and * limitations under the License. * ******************************************************************************/ #ifndef BT_TARGET_H #define BT_TARGET_H #ifndef BUILDCFG #define BUILDCFG #endif #if !defined(HAS_BDROID_BUILDCFG) && !defined(HAS_NO_BDROID_BUILDCFG) #error "An Android.mk file did not include bdroid_CFLAGS and possibly not bdorid_C_INCLUDES" #endif #ifdef HAS_BDROID_BUILDCFG #include "bdroid_buildcfg.h" #endif #include "bt_types.h" /* This must be defined AFTER buildcfg.h */ /* Include common GKI definitions used by this platform */ #include "gki_target.h" #include "dyn_mem.h" /* defines static and/or dynamic memory for components */ //------------------Added from bdroid_buildcfg.h--------------------- #ifndef L2CAP_EXTFEA_SUPPORTED_MASK #define L2CAP_EXTFEA_SUPPORTED_MASK (L2CAP_EXTFEA_ENH_RETRANS | L2CAP_EXTFEA_STREAM_MODE | L2CAP_EXTFEA_NO_CRC | L2CAP_EXTFEA_FIXED_CHNLS) #endif #ifndef BTUI_OPS_FORMATS #define BTUI_OPS_FORMATS (BTA_OP_VCARD21_MASK | BTA_OP_ANY_MASK) #endif #ifndef BTA_RFC_MTU_SIZE #define BTA_RFC_MTU_SIZE (L2CAP_MTU_SIZE-L2CAP_MIN_OFFSET-RFCOMM_DATA_OVERHEAD) #endif #ifndef SBC_NO_PCM_CPY_OPTION #define SBC_NO_PCM_CPY_OPTION FALSE #endif #ifndef BTA_INCLUDED #define BTA_INCLUDED TRUE #endif #ifndef BTA_PAN_INCLUDED #define BTA_PAN_INCLUDED TRUE #endif #ifndef BTA_HH_INCLUDED #define BTA_HH_INCLUDED TRUE #endif #ifndef BTA_HH_ROLE #define BTA_HH_ROLE BTA_MASTER_ROLE_PREF #endif #ifndef BTA_HH_LE_INCLUDED #define BTA_HH_LE_INCLUDED TRUE #endif #ifndef BTA_AR_INCLUDED #define BTA_AR_INCLUDED TRUE #endif #ifndef BTA_AV_INCLUDED #define BTA_AV_INCLUDED TRUE #endif #ifndef BTA_GATT_INCLUDED #define BTA_GATT_INCLUDED TRUE #endif #ifndef BTA_AV_SINK_INCLUDED #define BTA_AV_SINK_INCLUDED FALSE #endif #ifndef BTA_DISABLE_DELAY #define BTA_DISABLE_DELAY 200 /* in milliseconds */ #endif // If the next wakeup time is less than this threshold, we should acquire // a wakelock instead of setting a wake alarm so we're not bouncing in // and out of suspend frequently. // in millisecond // TODO(zachoverflow): reinstate in alarm code #ifndef GKI_TIMER_INTERVAL_FOR_WAKELOCK #define GKI_TIMER_INTERVAL_FOR_WAKELOCK 3000 #endif #ifndef BTA_SYS_TIMER_PERIOD #define BTA_SYS_TIMER_PERIOD 100 #endif #ifndef SBC_FOR_EMBEDDED_LINUX #define SBC_FOR_EMBEDDED_LINUX TRUE #endif #ifndef AVDT_VERSION #define AVDT_VERSION 0x0102 #endif #ifndef BTA_AG_AT_MAX_LEN #define BTA_AG_AT_MAX_LEN 512 #endif #ifndef BTA_AVRCP_FF_RW_SUPPORT #define BTA_AVRCP_FF_RW_SUPPORT TRUE #endif #ifndef BTA_AG_SCO_PKT_TYPES #define BTA_AG_SCO_PKT_TYPES (BTM_SCO_LINK_ONLY_MASK | BTM_SCO_PKT_TYPES_MASK_EV3 | BTM_SCO_PKT_TYPES_MASK_NO_3_EV3 | BTM_SCO_PKT_TYPES_MASK_NO_2_EV5 | BTM_SCO_PKT_TYPES_MASK_NO_3_EV5) #endif #ifndef BTA_AV_RET_TOUT #define BTA_AV_RET_TOUT 15 #endif #ifndef PORCHE_PAIRING_CONFLICT #define PORCHE_PAIRING_CONFLICT TRUE #endif #ifndef BTA_AV_CO_CP_SCMS_T #define BTA_AV_CO_CP_SCMS_T FALSE #endif /* This feature is used to eanble interleaved scan*/ #ifndef BTA_HOST_INTERLEAVE_SEARCH #define BTA_HOST_INTERLEAVE_SEARCH FALSE #endif #ifndef BT_USE_TRACES #define BT_USE_TRACES TRUE #endif #ifndef BT_TRACE_BTIF #define BT_TRACE_BTIF TRUE #endif #ifndef BT_TRACE_VERBOSE #define BT_TRACE_VERBOSE FALSE #endif #ifndef BTA_DM_SDP_DB_SIZE #define BTA_DM_SDP_DB_SIZE 8000 #endif #ifndef HL_INCLUDED #define HL_INCLUDED TRUE #endif #ifndef AG_VOICE_SETTINGS #define AG_VOICE_SETTINGS HCI_DEFAULT_VOICE_SETTINGS #endif #ifndef BTIF_DM_OOB_TEST #define BTIF_DM_OOB_TEST TRUE #endif // How long to wait before activating sniff mode after entering the // idle state for FTS, OPS connections #ifndef BTA_FTS_OPS_IDLE_TO_SNIFF_DELAY_MS #define BTA_FTS_OPS_IDLE_TO_SNIFF_DELAY_MS 7000 #endif //------------------End added from bdroid_buildcfg.h--------------------- /****************************************************************************** ** ** GKI Buffer Pools ** ******************************************************************************/ /* Receives HCI events from the lower-layer. */ #ifndef HCI_CMD_POOL_ID #define HCI_CMD_POOL_ID GKI_POOL_ID_2 #endif #ifndef HCI_CMD_POOL_BUF_SIZE #define HCI_CMD_POOL_BUF_SIZE GKI_BUF2_SIZE #endif /* Receives ACL data packets from thelower-layer. */ #ifndef HCI_ACL_POOL_ID #define HCI_ACL_POOL_ID GKI_POOL_ID_3 #endif /* Maximum number of buffers available for ACL receive data. */ #ifndef HCI_ACL_BUF_MAX #define HCI_ACL_BUF_MAX GKI_BUF3_MAX #endif /* Receives SCO data packets from the lower-layer. */ #ifndef HCI_SCO_POOL_ID #define HCI_SCO_POOL_ID GKI_POOL_ID_6 #endif /* Sends SDP data packets. */ #ifndef SDP_POOL_ID #define SDP_POOL_ID 3 #endif /* Sends RFCOMM command packets. */ #ifndef RFCOMM_CMD_POOL_ID #define RFCOMM_CMD_POOL_ID GKI_POOL_ID_2 #endif /* Sends RFCOMM data packets. */ #ifndef RFCOMM_DATA_POOL_ID #define RFCOMM_DATA_POOL_ID GKI_POOL_ID_3 #endif #ifndef RFCOMM_DATA_POOL_BUF_SIZE #define RFCOMM_DATA_POOL_BUF_SIZE GKI_BUF3_SIZE #endif /* Sends L2CAP packets to the peer and HCI messages to the controller. */ #ifndef L2CAP_CMD_POOL_ID #define L2CAP_CMD_POOL_ID GKI_POOL_ID_2 #endif /* Sends L2CAP segmented packets in ERTM mode */ #ifndef L2CAP_FCR_TX_POOL_ID #define L2CAP_FCR_TX_POOL_ID HCI_ACL_POOL_ID #endif /* Receives L2CAP segmented packets in ERTM mode */ #ifndef L2CAP_FCR_RX_POOL_ID #define L2CAP_FCR_RX_POOL_ID HCI_ACL_POOL_ID #endif /* Number of ACL buffers to assign to LE if the HCI buffer pool is shared with BR/EDR */ #ifndef L2C_DEF_NUM_BLE_BUF_SHARED #define L2C_DEF_NUM_BLE_BUF_SHARED 1 #endif /* Used by BTM when it sends HCI commands to the controller. */ #ifndef BTM_CMD_POOL_ID #define BTM_CMD_POOL_ID GKI_POOL_ID_2 #endif #ifndef OBX_LRG_DATA_POOL_SIZE #define OBX_LRG_DATA_POOL_SIZE GKI_BUF4_SIZE #endif #ifndef OBX_LRG_DATA_POOL_ID #define OBX_LRG_DATA_POOL_ID GKI_POOL_ID_4 #endif /* Used to send data to L2CAP. */ #ifndef GAP_DATA_POOL_ID #define GAP_DATA_POOL_ID GKI_POOL_ID_3 #endif #ifndef SPP_DB_SIZE #define SPP_DB_SIZE GKI_BUF3_SIZE #endif /* BNEP data and protocol messages. */ #ifndef BNEP_POOL_ID #define BNEP_POOL_ID GKI_POOL_ID_3 #endif /* RPC pool for temporary trace message buffers. */ #ifndef RPC_SCRATCH_POOL_ID #define RPC_SCRATCH_POOL_ID GKI_POOL_ID_2 #endif /* AVDTP pool for protocol messages */ #ifndef AVDT_CMD_POOL_ID #define AVDT_CMD_POOL_ID GKI_POOL_ID_2 #endif /* AVDTP pool size for media packets in case of fragmentation */ #ifndef AVDT_DATA_POOL_SIZE #define AVDT_DATA_POOL_SIZE GKI_BUF3_SIZE #endif #ifndef PAN_POOL_ID #define PAN_POOL_ID GKI_POOL_ID_3 /* Maximum amount of the shared buffer to allocate for PAN */ #define PAN_POOL_MAX (GKI_BUF3_MAX / 4) #endif /* AVCTP pool for protocol messages */ #ifndef AVCT_CMD_POOL_ID #define AVCT_CMD_POOL_ID GKI_POOL_ID_1 #endif /* AVRCP pool for protocol messages */ #ifndef AVRC_CMD_POOL_ID #define AVRC_CMD_POOL_ID GKI_POOL_ID_1 #endif /* AVRCP pool size for protocol messages */ #ifndef AVRC_CMD_POOL_SIZE #define AVRC_CMD_POOL_SIZE GKI_BUF1_SIZE #endif /* AVRCP Metadata pool for protocol messages */ #ifndef AVRC_META_CMD_POOL_ID #define AVRC_META_CMD_POOL_ID GKI_POOL_ID_2 #endif /* AVRCP Metadata pool size for protocol messages */ #ifndef AVRC_META_CMD_POOL_SIZE #define AVRC_META_CMD_POOL_SIZE GKI_BUF2_SIZE #endif /* AVRCP buffer size for browsing channel messages */ #ifndef AVRC_BROWSE_POOL_SIZE #define AVRC_BROWSE_POOL_SIZE GKI_MAX_BUF_SIZE #endif #ifndef BTA_HL_LRG_DATA_POOL_ID #define BTA_HL_LRG_DATA_POOL_ID GKI_POOL_ID_7 #endif /* GATT Server Database pool ID */ #ifndef GATT_DB_POOL_ID #define GATT_DB_POOL_ID GKI_POOL_ID_8 #endif /* GATT Data sending buffer pool ID, use default ACL pool for fix channel data */ #ifndef GATT_BUF_POOL_ID #define GATT_BUF_POOL_ID HCI_ACL_POOL_ID #endif /****************************************************************************** ** ** Lower Layer Interface ** ******************************************************************************/ /* Macro for allocating buffer for HCI commands */ #ifndef HCI_GET_CMD_BUF #if (!defined(HCI_USE_VARIABLE_SIZE_CMD_BUF) || (HCI_USE_VARIABLE_SIZE_CMD_BUF == FALSE)) /* Allocate fixed-size buffer from HCI_CMD_POOL (default case) */ #define HCI_GET_CMD_BUF(paramlen) ((BT_HDR *)GKI_getpoolbuf (HCI_CMD_POOL_ID)) #else /* Allocate smallest possible buffer (for platforms with limited RAM) */ #define HCI_GET_CMD_BUF(paramlen) ((BT_HDR *)GKI_getbuf ((UINT16)(BT_HDR_SIZE + HCIC_PREAMBLE_SIZE + (paramlen)))) #endif #endif /* HCI_GET_CMD_BUF */ /****************************************************************************** ** ** HCI Services (H4) ** ******************************************************************************/ /* Use 2 second for low-resolution systems, override to 1 for high-resolution systems */ #ifndef BT_1SEC_TIMEOUT #define BT_1SEC_TIMEOUT (2) #endif /* Quick Timer */ /* if L2CAP_FCR_INCLUDED is TRUE then it should have 100 millisecond resolution */ /* if none of them is included then QUICK_TIMER_TICKS_PER_SEC is set to 0 to exclude quick timer */ #ifndef QUICK_TIMER_TICKS_PER_SEC #define QUICK_TIMER_TICKS_PER_SEC 10 /* 100ms timer */ #endif /****************************************************************************** ** ** BTM ** ******************************************************************************/ /* Cancel Inquiry on incoming SSP */ #ifndef BTM_NO_SSP_ON_INQUIRY #define BTM_NO_SSP_ON_INQUIRY FALSE #endif /* Includes SCO if TRUE */ #ifndef BTM_SCO_INCLUDED #define BTM_SCO_INCLUDED TRUE /* TRUE includes SCO code */ #endif /* Includes SCO if TRUE */ #ifndef BTM_SCO_HCI_INCLUDED #define BTM_SCO_HCI_INCLUDED FALSE /* TRUE includes SCO over HCI code */ #endif /* Includes WBS if TRUE */ #ifndef BTM_WBS_INCLUDED #define BTM_WBS_INCLUDED FALSE /* TRUE includes WBS code */ #endif /* This is used to work around a controller bug that doesn't like Disconnect ** issued while there is a role switch in progress */ #ifndef BTM_DISC_DURING_RS #define BTM_DISC_DURING_RS TRUE #endif /************************** ** Initial SCO TX credit *************************/ /* max TX SCO data packet size */ #ifndef BTM_SCO_DATA_SIZE_MAX #define BTM_SCO_DATA_SIZE_MAX 240 #endif /* The size in bytes of the BTM inquiry database. */ #ifndef BTM_INQ_DB_SIZE #define BTM_INQ_DB_SIZE 40 #endif /* The default scan mode */ #ifndef BTM_DEFAULT_SCAN_TYPE #define BTM_DEFAULT_SCAN_TYPE BTM_SCAN_TYPE_INTERLACED #endif /* Should connections to unknown devices be allowed when not discoverable? */ #ifndef BTM_ALLOW_CONN_IF_NONDISCOVER #define BTM_ALLOW_CONN_IF_NONDISCOVER TRUE #endif /* Sets the Page_Scan_Window: the length of time that the device is performing a page scan. */ #ifndef BTM_DEFAULT_CONN_WINDOW #define BTM_DEFAULT_CONN_WINDOW 0x0012 #endif /* Sets the Page_Scan_Activity: the interval between the start of two consecutive page scans. */ #ifndef BTM_DEFAULT_CONN_INTERVAL #define BTM_DEFAULT_CONN_INTERVAL 0x0800 #endif /* When automatic inquiry scan is enabled, this sets the inquiry scan window. */ #ifndef BTM_DEFAULT_DISC_WINDOW #define BTM_DEFAULT_DISC_WINDOW 0x0012 #endif /* When automatic inquiry scan is enabled, this sets the inquiry scan interval. */ #ifndef BTM_DEFAULT_DISC_INTERVAL #define BTM_DEFAULT_DISC_INTERVAL 0x0800 #endif /* Default class of device * {SERVICE_CLASS, MAJOR_CLASS, MINOR_CLASS} * * SERVICE_CLASS:0x5A (Bit17 -Networking,Bit19 - Capturing,Bit20 -Object Transfer,Bit22 -Telephony) * MAJOR_CLASS:0x02 - PHONE * MINOR_CLASS:0x0C - SMART_PHONE * */ #ifndef BTA_DM_COD #define BTA_DM_COD {0x5A, 0x02, 0x0C} #endif /* The number of SCO links. */ #ifndef BTM_MAX_SCO_LINKS #define BTM_MAX_SCO_LINKS 3 #endif /* The preferred type of SCO links (2-eSCO, 0-SCO). */ #ifndef BTM_DEFAULT_SCO_MODE #define BTM_DEFAULT_SCO_MODE 2 #endif /* The number of security records for peer devices. */ #ifndef BTM_SEC_MAX_DEVICE_RECORDS #define BTM_SEC_MAX_DEVICE_RECORDS 100 #endif /* The number of security records for services. */ #ifndef BTM_SEC_MAX_SERVICE_RECORDS #define BTM_SEC_MAX_SERVICE_RECORDS 32 #endif /* If True, force a retrieval of remote device name for each bond in case it's changed */ #ifndef BTM_SEC_FORCE_RNR_FOR_DBOND #define BTM_SEC_FORCE_RNR_FOR_DBOND FALSE #endif /* Maximum device name length used in btm database. */ #ifndef BTM_MAX_REM_BD_NAME_LEN #define BTM_MAX_REM_BD_NAME_LEN 248 #endif /* Maximum local device name length stored btm database. '0' disables storage of the local name in BTM */ #ifndef BTM_MAX_LOC_BD_NAME_LEN #define BTM_MAX_LOC_BD_NAME_LEN 248 #endif /* Fixed Default String. When this is defined as null string, the device's * product model name is used as the default local name. */ #ifndef BTM_DEF_LOCAL_NAME #define BTM_DEF_LOCAL_NAME "" #endif /* Maximum service name stored with security authorization (0 if not needed) */ #ifndef BTM_SEC_SERVICE_NAME_LEN #define BTM_SEC_SERVICE_NAME_LEN BT_MAX_SERVICE_NAME_LEN #endif /* Maximum length of the service name. */ #ifndef BT_MAX_SERVICE_NAME_LEN #define BT_MAX_SERVICE_NAME_LEN 21 #endif /* ACL buffer size in HCI Host Buffer Size command. */ #ifndef BTM_ACL_BUF_SIZE #define BTM_ACL_BUF_SIZE 0 #endif /* The maximum number of clients that can register with the power manager. */ #ifndef BTM_MAX_PM_RECORDS #define BTM_MAX_PM_RECORDS 2 #endif /* This is set to show debug trace messages for the power manager. */ #ifndef BTM_PM_DEBUG #define BTM_PM_DEBUG FALSE #endif /* This is set to TRUE if link is to be unparked due to BTM_CreateSCO API. */ #ifndef BTM_SCO_WAKE_PARKED_LINK #define BTM_SCO_WAKE_PARKED_LINK TRUE #endif /* If the user does not respond to security process requests within this many seconds, * a negative response would be sent automatically. * 30 is LMP response timeout value */ #ifndef BTM_SEC_TIMEOUT_VALUE #define BTM_SEC_TIMEOUT_VALUE 35 #endif /* Maximum number of callbacks that can be registered using BTM_RegisterForVSEvents */ #ifndef BTM_MAX_VSE_CALLBACKS #define BTM_MAX_VSE_CALLBACKS 3 #endif /****************************************** ** Lisbon Features *******************************************/ /* This is set to TRUE if the FEC is required for EIR packet. */ #ifndef BTM_EIR_DEFAULT_FEC_REQUIRED #define BTM_EIR_DEFAULT_FEC_REQUIRED TRUE #endif /* The IO capability of the local device (for Simple Pairing) */ #ifndef BTM_LOCAL_IO_CAPS #define BTM_LOCAL_IO_CAPS BTM_IO_CAP_IO #endif #ifndef BTM_LOCAL_IO_CAPS_BLE #define BTM_LOCAL_IO_CAPS_BLE BTM_IO_CAP_KBDISP #endif /* The default MITM Protection Requirement (for Simple Pairing) * Possible values are BTM_AUTH_SP_YES or BTM_AUTH_SP_NO */ #ifndef BTM_DEFAULT_AUTH_REQ #define BTM_DEFAULT_AUTH_REQ BTM_AUTH_SP_NO #endif /* The default MITM Protection Requirement for dedicated bonding using Simple Pairing * Possible values are BTM_AUTH_AP_YES or BTM_AUTH_AP_NO */ #ifndef BTM_DEFAULT_DD_AUTH_REQ #define BTM_DEFAULT_DD_AUTH_REQ BTM_AUTH_AP_YES #endif /* Include Out-of-Band implementation for Simple Pairing */ #ifndef BTM_OOB_INCLUDED #define BTM_OOB_INCLUDED TRUE #endif /* TRUE to include Sniff Subrating */ #ifndef BTM_SSR_INCLUDED #define BTM_SSR_INCLUDED TRUE #endif /************************* ** End of Lisbon Features **************************/ /* 4.1/4.2 secure connections feature */ #ifndef SC_MODE_INCLUDED #define SC_MODE_INCLUDED TRUE #endif /* Used for conformance testing ONLY */ #ifndef BTM_BLE_CONFORMANCE_TESTING #define BTM_BLE_CONFORMANCE_TESTING FALSE #endif /****************************************************************************** ** ** L2CAP ** ******************************************************************************/ /* The maximum number of simultaneous links that L2CAP can support. */ #ifndef MAX_ACL_CONNECTIONS #define MAX_L2CAP_LINKS 7 #else #define MAX_L2CAP_LINKS MAX_ACL_CONNECTIONS #endif /* The maximum number of simultaneous channels that L2CAP can support. */ #ifndef MAX_L2CAP_CHANNELS #define MAX_L2CAP_CHANNELS 16 #endif /* The maximum number of simultaneous applications that can register with L2CAP. */ #ifndef MAX_L2CAP_CLIENTS #define MAX_L2CAP_CLIENTS 15 #endif /* The number of seconds of link inactivity before a link is disconnected. */ #ifndef L2CAP_LINK_INACTIVITY_TOUT #define L2CAP_LINK_INACTIVITY_TOUT 4 #endif /* The number of seconds of link inactivity after bonding before a link is disconnected. */ #ifndef L2CAP_BONDING_TIMEOUT #define L2CAP_BONDING_TIMEOUT 3 #endif /* The time from the HCI connection complete to disconnect if no channel is established. */ #ifndef L2CAP_LINK_STARTUP_TOUT #define L2CAP_LINK_STARTUP_TOUT 60 #endif /* The L2CAP MTU; must be in accord with the HCI ACL pool size. */ #ifndef L2CAP_MTU_SIZE #define L2CAP_MTU_SIZE 1691 #endif /* The L2CAP MPS over Bluetooth; must be in accord with the FCR tx pool size and ACL down buffer size. */ #ifndef L2CAP_MPS_OVER_BR_EDR #define L2CAP_MPS_OVER_BR_EDR 1010 #endif /* If host flow control enabled, this is the number of buffers the controller can have unacknowledged. */ #ifndef L2CAP_HOST_FC_ACL_BUFS #define L2CAP_HOST_FC_ACL_BUFS 20 #endif /* This is set to enable L2CAP to take the ACL link out of park mode when ACL data is to be sent. */ #ifndef L2CAP_WAKE_PARKED_LINK #define L2CAP_WAKE_PARKED_LINK TRUE #endif /* Whether link wants to be the master or the slave. */ #ifndef L2CAP_DESIRED_LINK_ROLE #define L2CAP_DESIRED_LINK_ROLE HCI_ROLE_SLAVE #endif /* Include Non-Flushable Packet Boundary Flag feature of Lisbon */ #ifndef L2CAP_NON_FLUSHABLE_PB_INCLUDED #define L2CAP_NON_FLUSHABLE_PB_INCLUDED TRUE #endif /* Minimum number of ACL credit for high priority link */ #ifndef L2CAP_HIGH_PRI_MIN_XMIT_QUOTA #define L2CAP_HIGH_PRI_MIN_XMIT_QUOTA 5 #endif /* used for monitoring HCI ACL credit management */ #ifndef L2CAP_HCI_FLOW_CONTROL_DEBUG #define L2CAP_HCI_FLOW_CONTROL_DEBUG TRUE #endif /* Used for calculating transmit buffers off of */ #ifndef L2CAP_NUM_XMIT_BUFFS #define L2CAP_NUM_XMIT_BUFFS HCI_ACL_BUF_MAX #endif /* Unicast Connectionless Data */ #ifndef L2CAP_UCD_INCLUDED #define L2CAP_UCD_INCLUDED FALSE #endif /* Unicast Connectionless Data MTU */ #ifndef L2CAP_UCD_MTU #define L2CAP_UCD_MTU L2CAP_MTU_SIZE #endif /* Unicast Connectionless Data Idle Timeout */ #ifndef L2CAP_UCD_IDLE_TIMEOUT #define L2CAP_UCD_IDLE_TIMEOUT 2 #endif /* Unicast Connectionless Data Idle Timeout */ #ifndef L2CAP_UCD_CH_PRIORITY #define L2CAP_UCD_CH_PRIORITY L2CAP_CHNL_PRIORITY_MEDIUM #endif /* Used for features using fixed channels; set to zero if no fixed channels supported (BLE, etc.) */ /* Excluding L2CAP signaling channel and UCD */ #ifndef L2CAP_NUM_FIXED_CHNLS #define L2CAP_NUM_FIXED_CHNLS 32 #endif /* First fixed channel supported */ #ifndef L2CAP_FIRST_FIXED_CHNL #define L2CAP_FIRST_FIXED_CHNL 4 #endif #ifndef L2CAP_LAST_FIXED_CHNL #define L2CAP_LAST_FIXED_CHNL (L2CAP_FIRST_FIXED_CHNL + L2CAP_NUM_FIXED_CHNLS - 1) #endif /* Round Robin service channels in link */ #ifndef L2CAP_ROUND_ROBIN_CHANNEL_SERVICE #define L2CAP_ROUND_ROBIN_CHANNEL_SERVICE TRUE #endif /* Used for calculating transmit buffers off of */ #ifndef L2CAP_NUM_XMIT_BUFFS #define L2CAP_NUM_XMIT_BUFFS HCI_ACL_BUF_MAX #endif /* used for monitoring eL2CAP data flow */ #ifndef L2CAP_ERTM_STATS #define L2CAP_ERTM_STATS FALSE #endif /* Used for conformance testing ONLY: When TRUE lets scriptwrapper overwrite info response */ #ifndef L2CAP_CONFORMANCE_TESTING #define L2CAP_CONFORMANCE_TESTING FALSE #endif /* * Max bytes per connection to buffer locally before dropping the * connection if local client does not receive it - default is 1MB */ #ifndef L2CAP_MAX_RX_BUFFER #define L2CAP_MAX_RX_BUFFER 0x100000 #endif #ifndef TIMER_PARAM_TYPE #define TIMER_PARAM_TYPE UINT32 #endif /****************************************************************************** ** ** BLE ** ******************************************************************************/ #ifndef BLE_INCLUDED #define BLE_INCLUDED TRUE #endif #ifndef BLE_ANDROID_CONTROLLER_SCAN_FILTER #define BLE_ANDROID_CONTROLLER_SCAN_FILTER TRUE #endif #ifndef LOCAL_BLE_CONTROLLER_ID #define LOCAL_BLE_CONTROLLER_ID (1) #endif /* * Toggles support for general LE privacy features such as remote address * resolution, local address rotation etc. */ #ifndef BLE_PRIVACY_SPT #define BLE_PRIVACY_SPT TRUE #endif /* * Enables or disables support for local privacy (ex. address rotation) */ #ifndef BLE_LOCAL_PRIVACY_ENABLED #define BLE_LOCAL_PRIVACY_ENABLED TRUE #endif /* * Toggles support for vendor specific extensions such as RPA offloading, * feature discovery, multi-adv etc. */ #ifndef BLE_VND_INCLUDED #define BLE_VND_INCLUDED FALSE #endif #ifndef BTM_BLE_ADV_TX_POWER #define BTM_BLE_ADV_TX_POWER {-21, -15, -7, 1, 9} #endif #ifndef BLE_BATCH_SCAN_INCLUDED #define BLE_BATCH_SCAN_INCLUDED TRUE #endif /****************************************************************************** ** ** ATT/GATT Protocol/Profile Settings ** ******************************************************************************/ #ifndef BTA_GATT_INCLUDED #if BLE_INCLUDED == TRUE #define BTA_GATT_INCLUDED TRUE #else #define BTA_GATT_INCLUDED FALSE #endif #endif #if BTA_GATT_INCLUDED == TRUE && BLE_INCLUDED == FALSE #error "can't have GATT without BLE" #endif #ifndef BLE_LLT_INCLUDED #define BLE_LLT_INCLUDED TRUE #endif #ifndef ATT_INCLUDED #define ATT_INCLUDED TRUE #endif #ifndef ATT_DEBUG #define ATT_DEBUG TRUE #endif #ifndef BLE_PERIPHERAL_MODE_SUPPORT #define BLE_PERIPHERAL_MODE_SUPPORT TRUE #endif #ifndef BLE_DELAY_REQUEST_ENC /* This flag is to work around IPHONE problem, We need to wait for iPhone ready before send encryption request to iPhone */ #define BLE_DELAY_REQUEST_ENC FALSE #endif #ifndef GAP_TRANSPORT_SUPPORTED #define GAP_TRANSPORT_SUPPORTED GATT_TRANSPORT_LE_BR_EDR #endif #ifndef GATTP_TRANSPORT_SUPPORTED #define GATTP_TRANSPORT_SUPPORTED GATT_TRANSPORT_LE_BR_EDR #endif #ifndef GATT_MAX_SR_PROFILES #define GATT_MAX_SR_PROFILES 32 /* max is 32 */ #endif #ifndef GATT_MAX_APPS #define GATT_MAX_APPS 32 /* note: 2 apps used internally GATT and GAP */ #endif #ifndef GATT_MAX_PHY_CHANNEL #define GATT_MAX_PHY_CHANNEL 7 #endif /* Used for conformance testing ONLY */ #ifndef GATT_CONFORMANCE_TESTING #define GATT_CONFORMANCE_TESTING FALSE #endif /* number of background connection device allowence, ideally to be the same as WL size */ #ifndef GATT_MAX_BG_CONN_DEV #define GATT_MAX_BG_CONN_DEV 32 #endif /****************************************************************************** ** ** SMP ** ******************************************************************************/ #ifndef SMP_INCLUDED #if BLE_INCLUDED == TRUE #define SMP_INCLUDED TRUE #else #define SMP_INCLUDED FALSE #endif #endif #if SMP_INCLUDED == TRUE && BLE_INCLUDED == FALSE #error "can't have SMP without BLE" #endif #ifndef SMP_DEBUG #define SMP_DEBUG FALSE #endif #ifndef SMP_DEFAULT_AUTH_REQ #define SMP_DEFAULT_AUTH_REQ SMP_AUTH_NB_ENC_ONLY #endif #ifndef SMP_MAX_ENC_KEY_SIZE #define SMP_MAX_ENC_KEY_SIZE 16 #endif #ifndef SMP_MIN_ENC_KEY_SIZE #define SMP_MIN_ENC_KEY_SIZE 7 #endif /* minimum link timeout after SMP pairing is done, leave room for key exchange and racing condition for the following service connection. Prefer greater than 0 second, and no less than default inactivity link idle timer(L2CAP_LINK_INACTIVITY_TOUT) in l2cap) */ #ifndef SMP_LINK_TOUT_MIN #if (L2CAP_LINK_INACTIVITY_TOUT > 0) #define SMP_LINK_TOUT_MIN L2CAP_LINK_INACTIVITY_TOUT #else #define SMP_LINK_TOUT_MIN 2 #endif #endif /****************************************************************************** ** ** SDP ** ******************************************************************************/ /* This is set to enable SDP server functionality. */ #ifndef SDP_SERVER_ENABLED #define SDP_SERVER_ENABLED TRUE #endif /* The maximum number of SDP records the server can support. */ #ifndef SDP_MAX_RECORDS #define SDP_MAX_RECORDS 30 #endif /* The maximum number of attributes in each record. */ #ifndef SDP_MAX_REC_ATTR #define SDP_MAX_REC_ATTR 25 #endif #ifndef SDP_MAX_PAD_LEN #define SDP_MAX_PAD_LEN 600 #endif /* The maximum length, in bytes, of an attribute. */ #ifndef SDP_MAX_ATTR_LEN #define SDP_MAX_ATTR_LEN 400 #endif /* The maximum number of attribute filters supported by SDP databases. */ #ifndef SDP_MAX_ATTR_FILTERS #define SDP_MAX_ATTR_FILTERS 15 #endif /* The maximum number of UUID filters supported by SDP databases. */ #ifndef SDP_MAX_UUID_FILTERS #define SDP_MAX_UUID_FILTERS 3 #endif /* This is set to enable SDP client functionality. */ #ifndef SDP_CLIENT_ENABLED #define SDP_CLIENT_ENABLED TRUE #endif /* The maximum number of record handles retrieved in a search. */ #ifndef SDP_MAX_DISC_SERVER_RECS #define SDP_MAX_DISC_SERVER_RECS 21 #endif /* The size of a scratchpad buffer, in bytes, for storing the response to an attribute request. */ #ifndef SDP_MAX_LIST_BYTE_COUNT #define SDP_MAX_LIST_BYTE_COUNT 4096 #endif /* The maximum number of parameters in an SDP protocol element. */ #ifndef SDP_MAX_PROTOCOL_PARAMS #define SDP_MAX_PROTOCOL_PARAMS 2 #endif /* The maximum number of simultaneous client and server connections. */ #ifndef SDP_MAX_CONNECTIONS #define SDP_MAX_CONNECTIONS 4 #endif /* The MTU size for the L2CAP configuration. */ #ifndef SDP_MTU_SIZE #define SDP_MTU_SIZE 672 #endif /* The flush timeout for the L2CAP configuration. */ #ifndef SDP_FLUSH_TO #define SDP_FLUSH_TO 0xFFFF #endif /* The name for security authorization. */ #ifndef SDP_SERVICE_NAME #define SDP_SERVICE_NAME "Service Discovery" #endif /* The security level for BTM. */ #ifndef SDP_SECURITY_LEVEL #define SDP_SECURITY_LEVEL BTM_SEC_NONE #endif /****************************************************************************** ** ** RFCOMM ** ******************************************************************************/ /* The maximum number of ports supported. */ #ifndef MAX_RFC_PORTS #define MAX_RFC_PORTS 30 #endif /* The maximum simultaneous links to different devices. */ #ifndef MAX_ACL_CONNECTIONS #define MAX_BD_CONNECTIONS 7 #else #define MAX_BD_CONNECTIONS MAX_ACL_CONNECTIONS #endif /* The port receive queue low watermark level, in bytes. */ #ifndef PORT_RX_LOW_WM #define PORT_RX_LOW_WM (BTA_RFC_MTU_SIZE * PORT_RX_BUF_LOW_WM) #endif /* The port receive queue high watermark level, in bytes. */ #ifndef PORT_RX_HIGH_WM #define PORT_RX_HIGH_WM (BTA_RFC_MTU_SIZE * PORT_RX_BUF_HIGH_WM) #endif /* The port receive queue critical watermark level, in bytes. */ #ifndef PORT_RX_CRITICAL_WM #define PORT_RX_CRITICAL_WM (BTA_RFC_MTU_SIZE * PORT_RX_BUF_CRITICAL_WM) #endif /* The port receive queue low watermark level, in number of buffers. */ #ifndef PORT_RX_BUF_LOW_WM #define PORT_RX_BUF_LOW_WM 4 #endif /* The port receive queue high watermark level, in number of buffers. */ #ifndef PORT_RX_BUF_HIGH_WM #define PORT_RX_BUF_HIGH_WM 10 #endif /* The port receive queue critical watermark level, in number of buffers. */ #ifndef PORT_RX_BUF_CRITICAL_WM #define PORT_RX_BUF_CRITICAL_WM 15 #endif /* The port transmit queue high watermark level, in bytes. */ #ifndef PORT_TX_HIGH_WM #define PORT_TX_HIGH_WM (BTA_RFC_MTU_SIZE * PORT_TX_BUF_HIGH_WM) #endif /* The port transmit queue critical watermark level, in bytes. */ #ifndef PORT_TX_CRITICAL_WM #define PORT_TX_CRITICAL_WM (BTA_RFC_MTU_SIZE * PORT_TX_BUF_CRITICAL_WM) #endif /* The port transmit queue high watermark level, in number of buffers. */ #ifndef PORT_TX_BUF_HIGH_WM #define PORT_TX_BUF_HIGH_WM 10 #endif /* The port transmit queue high watermark level, in number of buffers. */ #ifndef PORT_TX_BUF_CRITICAL_WM #define PORT_TX_BUF_CRITICAL_WM 15 #endif /* The RFCOMM multiplexer preferred flow control mechanism. */ #ifndef PORT_FC_DEFAULT #define PORT_FC_DEFAULT PORT_FC_CREDIT #endif /* The maximum number of credits receiver sends to peer when using credit-based flow control. */ #ifndef PORT_CREDIT_RX_MAX #define PORT_CREDIT_RX_MAX 16 #endif /* The credit low watermark level. */ #ifndef PORT_CREDIT_RX_LOW #define PORT_CREDIT_RX_LOW 8 #endif /* if application like BTA, Java or script test engine is running on other than BTU thread, */ /* PORT_SCHEDULE_LOCK shall be defined as GKI_sched_lock() or GKI_disable() */ #ifndef PORT_SCHEDULE_LOCK #define PORT_SCHEDULE_LOCK GKI_disable() #endif /* if application like BTA, Java or script test engine is running on other than BTU thread, */ /* PORT_SCHEDULE_LOCK shall be defined as GKI_sched_unlock() or GKI_enable() */ #ifndef PORT_SCHEDULE_UNLOCK #define PORT_SCHEDULE_UNLOCK GKI_enable() #endif /****************************************************************************** ** ** OBEX ** ******************************************************************************/ #define OBX_14_INCLUDED FALSE /* The maximum number of registered servers. */ #ifndef OBX_NUM_SERVERS #define OBX_NUM_SERVERS 12 #endif /* The maximum number of active clients. */ #ifndef OBX_NUM_CLIENTS #define OBX_NUM_CLIENTS 8 #endif /* This option is application when OBX_14_INCLUDED=TRUE Pool ID where to reassemble the SDU. This Pool will allow buffers to be used that are larger than the L2CAP_MAX_MTU. */ #ifndef OBX_USER_RX_POOL_ID #define OBX_USER_RX_POOL_ID OBX_LRG_DATA_POOL_ID #endif /* This option is application when OBX_14_INCLUDED=TRUE Pool ID where to hold the SDU. This Pool will allow buffers to be used that are larger than the L2CAP_MAX_MTU. */ #ifndef OBX_USER_TX_POOL_ID #define OBX_USER_TX_POOL_ID OBX_LRG_DATA_POOL_ID #endif /* This option is application when OBX_14_INCLUDED=TRUE GKI Buffer Pool ID used to hold MPS segments during SDU reassembly */ #ifndef OBX_FCR_RX_POOL_ID #define OBX_FCR_RX_POOL_ID HCI_ACL_POOL_ID #endif /* This option is application when OBX_14_INCLUDED=TRUE GKI Buffer Pool ID used to hold MPS segments used in (re)transmissions. L2CAP_DEFAULT_ERM_POOL_ID is specified to use the HCI ACL data pool. Note: This pool needs to have enough buffers to hold two times the window size negotiated in the L2CA_SetFCROptions (2 * tx_win_size) to allow for retransmissions. The size of each buffer must be able to hold the maximum MPS segment size passed in L2CA_SetFCROptions plus BT_HDR (8) + HCI preamble (4) + L2CAP_MIN_OFFSET (11 - as of BT 2.1 + EDR Spec). */ #ifndef OBX_FCR_TX_POOL_ID #define OBX_FCR_TX_POOL_ID HCI_ACL_POOL_ID #endif /* This option is application when OBX_14_INCLUDED=TRUE Size of the transmission window when using enhanced retransmission mode. Not used in basic and streaming modes. Range: 1 - 63 */ #ifndef OBX_FCR_OPT_TX_WINDOW_SIZE_BR_EDR #define OBX_FCR_OPT_TX_WINDOW_SIZE_BR_EDR 20 #endif /* This option is application when OBX_14_INCLUDED=TRUE Number of transmission attempts for a single I-Frame before taking Down the connection. Used In ERTM mode only. Value is Ignored in basic and Streaming modes. Range: 0, 1-0xFF 0 - infinite retransmissions 1 - single transmission */ #ifndef OBX_FCR_OPT_MAX_TX_B4_DISCNT #define OBX_FCR_OPT_MAX_TX_B4_DISCNT 20 #endif /* This option is application when OBX_14_INCLUDED=TRUE Retransmission Timeout Range: Minimum 2000 (2 secs) on BR/EDR when supporting PBF. */ #ifndef OBX_FCR_OPT_RETX_TOUT #define OBX_FCR_OPT_RETX_TOUT 2000 #endif /* This option is application when OBX_14_INCLUDED=TRUE Monitor Timeout Range: Minimum 12000 (12 secs) on BR/EDR when supporting PBF. */ #ifndef OBX_FCR_OPT_MONITOR_TOUT #define OBX_FCR_OPT_MONITOR_TOUT 12000 #endif /* This option is application when OBX_14_INCLUDED=TRUE Maximum PDU payload size. Suggestion: The maximum amount of data that will fit into a 3-DH5 packet. Range: 2 octets */ #ifndef OBX_FCR_OPT_MAX_PDU_SIZE #define OBX_FCR_OPT_MAX_PDU_SIZE L2CAP_MPS_OVER_BR_EDR #endif /****************************************************************************** ** ** BNEP ** ******************************************************************************/ #ifndef BNEP_INCLUDED #define BNEP_INCLUDED TRUE #endif /* BNEP status API call is used mainly to get the L2CAP handle */ #ifndef BNEP_SUPPORTS_STATUS_API #define BNEP_SUPPORTS_STATUS_API TRUE #endif /* ** When BNEP connection changes roles after the connection is established ** we will do an authentication check again on the new role */ #ifndef BNEP_DO_AUTH_FOR_ROLE_SWITCH #define BNEP_DO_AUTH_FOR_ROLE_SWITCH TRUE #endif /* Maximum number of protocol filters supported. */ #ifndef BNEP_MAX_PROT_FILTERS #define BNEP_MAX_PROT_FILTERS 5 #endif /* Maximum number of multicast filters supported. */ #ifndef BNEP_MAX_MULTI_FILTERS #define BNEP_MAX_MULTI_FILTERS 5 #endif /* Minimum MTU size. */ #ifndef BNEP_MIN_MTU_SIZE #define BNEP_MIN_MTU_SIZE L2CAP_MTU_SIZE #endif /* Preferred MTU size. */ #ifndef BNEP_MTU_SIZE #define BNEP_MTU_SIZE BNEP_MIN_MTU_SIZE #endif /* Maximum number of buffers allowed in transmit data queue. */ #ifndef BNEP_MAX_XMITQ_DEPTH #define BNEP_MAX_XMITQ_DEPTH 20 #endif /* Maximum number BNEP of connections supported. */ #ifndef BNEP_MAX_CONNECTIONS #define BNEP_MAX_CONNECTIONS 7 #endif /****************************************************************************** ** ** AVDTP ** ******************************************************************************/ #ifndef AVDT_INCLUDED #define AVDT_INCLUDED TRUE #endif /* Include reporting capability in AVDTP */ #ifndef AVDT_REPORTING #define AVDT_REPORTING TRUE #endif /* Include multiplexing capability in AVDTP */ #ifndef AVDT_MULTIPLEXING #define AVDT_MULTIPLEXING TRUE #endif /* Number of simultaneous links to different peer devices. */ #ifndef AVDT_NUM_LINKS #define AVDT_NUM_LINKS 2 #endif /* Number of simultaneous stream endpoints. */ #ifndef AVDT_NUM_SEPS #define AVDT_NUM_SEPS 3 #endif /* Number of transport channels setup per media stream(audio or video) */ #ifndef AVDT_NUM_CHANNELS #if AVDT_REPORTING == TRUE /* signaling, media and reporting channels */ #define AVDT_NUM_CHANNELS 3 #else /* signaling and media channels */ #define AVDT_NUM_CHANNELS 2 #endif // AVDT_REPORTING #endif // AVDT_NUM_CHANNELS /* Number of transport channels setup by AVDT for all media streams * AVDT_NUM_CHANNELS * Number of simultaneous streams. */ #ifndef AVDT_NUM_TC_TBL #define AVDT_NUM_TC_TBL 6 #endif /* Maximum size in bytes of the codec capabilities information element. */ #ifndef AVDT_CODEC_SIZE #define AVDT_CODEC_SIZE 10 #endif /* Maximum size in bytes of the content protection information element. */ #ifndef AVDT_PROTECT_SIZE #define AVDT_PROTECT_SIZE 90 #endif /* Maximum number of GKI buffers in the fragment queue (for video frames). * Must be less than the number of buffers in the buffer pool of size AVDT_DATA_POOL_SIZE */ #ifndef AVDT_MAX_FRAG_COUNT #define AVDT_MAX_FRAG_COUNT 15 #endif /****************************************************************************** ** ** PAN ** ******************************************************************************/ #ifndef PAN_INCLUDED #define PAN_INCLUDED TRUE #endif /* This will enable the PANU role */ #ifndef PAN_SUPPORTS_ROLE_PANU #define PAN_SUPPORTS_ROLE_PANU TRUE #endif /* This will enable the GN role */ #ifndef PAN_SUPPORTS_ROLE_GN #define PAN_SUPPORTS_ROLE_GN TRUE #endif /* This will enable the NAP role */ #ifndef PAN_SUPPORTS_ROLE_NAP #define PAN_SUPPORTS_ROLE_NAP TRUE #endif /* This is just for debugging purposes */ #ifndef PAN_SUPPORTS_DEBUG_DUMP #define PAN_SUPPORTS_DEBUG_DUMP TRUE #endif /* Maximum number of PAN connections allowed */ #ifndef MAX_PAN_CONNS #define MAX_PAN_CONNS 7 #endif /* Default service name for NAP role */ #ifndef PAN_NAP_DEFAULT_SERVICE_NAME #define PAN_NAP_DEFAULT_SERVICE_NAME "Network Access Point Service" #endif /* Default service name for GN role */ #ifndef PAN_GN_DEFAULT_SERVICE_NAME #define PAN_GN_DEFAULT_SERVICE_NAME "Group Network Service" #endif /* Default service name for PANU role */ #ifndef PAN_PANU_DEFAULT_SERVICE_NAME #define PAN_PANU_DEFAULT_SERVICE_NAME "PAN User Service" #endif /* Default description for NAP role service */ #ifndef PAN_NAP_DEFAULT_DESCRIPTION #define PAN_NAP_DEFAULT_DESCRIPTION "NAP" #endif /* Default description for GN role service */ #ifndef PAN_GN_DEFAULT_DESCRIPTION #define PAN_GN_DEFAULT_DESCRIPTION "GN" #endif /* Default description for PANU role service */ #ifndef PAN_PANU_DEFAULT_DESCRIPTION #define PAN_PANU_DEFAULT_DESCRIPTION "PANU" #endif /* Default Security level for PANU role. */ #ifndef PAN_PANU_SECURITY_LEVEL #define PAN_PANU_SECURITY_LEVEL 0 #endif /* Default Security level for GN role. */ #ifndef PAN_GN_SECURITY_LEVEL #define PAN_GN_SECURITY_LEVEL 0 #endif /* Default Security level for NAP role. */ #ifndef PAN_NAP_SECURITY_LEVEL #define PAN_NAP_SECURITY_LEVEL 0 #endif /****************************************************************************** ** ** GAP ** ******************************************************************************/ #ifndef GAP_INCLUDED #define GAP_INCLUDED TRUE #endif /* This is set to enable use of GAP L2CAP connections. */ #ifndef GAP_CONN_INCLUDED #define GAP_CONN_INCLUDED TRUE #endif /* This is set to enable posting event for data write */ #ifndef GAP_CONN_POST_EVT_INCLUDED #define GAP_CONN_POST_EVT_INCLUDED FALSE #endif /* The maximum number of simultaneous GAP L2CAP connections. */ #ifndef GAP_MAX_CONNECTIONS #define GAP_MAX_CONNECTIONS 30 #endif /* keep the raw data received from SDP server in database. */ #ifndef SDP_RAW_DATA_INCLUDED #define SDP_RAW_DATA_INCLUDED TRUE #endif /* Inquiry duration in 1.28 second units. */ #ifndef SDP_DEBUG #define SDP_DEBUG TRUE #endif /****************************************************************************** ** ** HID ** ******************************************************************************/ #ifndef HID_DEV_SUBCLASS #define HID_DEV_SUBCLASS COD_MINOR_POINTING #endif #ifndef HID_CONTROL_POOL_ID #define HID_CONTROL_POOL_ID 2 #endif #ifndef HID_INTERRUPT_POOL_ID #define HID_INTERRUPT_POOL_ID 2 #endif /************************************************************************* ** Definitions for Both HID-Host & Device */ #ifndef HID_MAX_SVC_NAME_LEN #define HID_MAX_SVC_NAME_LEN 32 #endif #ifndef HID_MAX_SVC_DESCR_LEN #define HID_MAX_SVC_DESCR_LEN 32 #endif #ifndef HID_MAX_PROV_NAME_LEN #define HID_MAX_PROV_NAME_LEN 32 #endif /************************************************************************* ** Definitions for HID-Host */ #ifndef HID_HOST_INCLUDED #define HID_HOST_INCLUDED TRUE #endif #ifndef HID_HOST_MAX_DEVICES #define HID_HOST_MAX_DEVICES 7 #endif #ifndef HID_HOST_MTU #define HID_HOST_MTU 640 #endif #ifndef HID_HOST_FLUSH_TO #define HID_HOST_FLUSH_TO 0xffff #endif #ifndef HID_HOST_MAX_CONN_RETRY #define HID_HOST_MAX_CONN_RETRY (3) #endif #ifndef HID_HOST_REPAGE_WIN #define HID_HOST_REPAGE_WIN (2) #endif /************************************************************************* * A2DP Definitions */ #ifndef A2D_INCLUDED #define A2D_INCLUDED TRUE #endif /****************************************************************************** ** ** AVCTP ** ******************************************************************************/ /* Number of simultaneous ACL links to different peer devices. */ #ifndef AVCT_NUM_LINKS #define AVCT_NUM_LINKS 2 #endif /* Number of simultaneous AVCTP connections. */ #ifndef AVCT_NUM_CONN #define AVCT_NUM_CONN 3 #endif /****************************************************************************** ** ** AVRCP ** ******************************************************************************/ #ifndef AVRC_METADATA_INCLUDED #define AVRC_METADATA_INCLUDED TRUE #endif #ifndef AVRC_ADV_CTRL_INCLUDED #define AVRC_ADV_CTRL_INCLUDED TRUE #endif #ifndef AVRC_CTLR_INCLUDED #define AVRC_CTLR_INCLUDED TRUE #endif /****************************************************************************** ** ** MCAP ** ******************************************************************************/ #ifndef MCA_INCLUDED #define MCA_INCLUDED FALSE #endif /* The MTU size for the L2CAP configuration on control channel. 48 is the minimal */ #ifndef MCA_CTRL_MTU #define MCA_CTRL_MTU 60 #endif /* The maximum number of registered MCAP instances. */ #ifndef MCA_NUM_REGS #define MCA_NUM_REGS 12 #endif /* The maximum number of control channels (to difference devices) per registered MCAP instances. */ #ifndef MCA_NUM_LINKS #define MCA_NUM_LINKS 3 #endif /* The maximum number of MDEP (including HDP echo) per registered MCAP instances. */ #ifndef MCA_NUM_DEPS #define MCA_NUM_DEPS 13 #endif /* The maximum number of MDL link per control channel. */ #ifndef MCA_NUM_MDLS #define MCA_NUM_MDLS 4 #endif /* Pool ID where to reassemble the SDU. */ #ifndef MCA_USER_RX_POOL_ID #define MCA_USER_RX_POOL_ID HCI_ACL_POOL_ID #endif /* Pool ID where to hold the SDU. */ #ifndef MCA_USER_TX_POOL_ID #define MCA_USER_TX_POOL_ID HCI_ACL_POOL_ID #endif /* GKI Buffer Pool ID used to hold MPS segments during SDU reassembly */ #ifndef MCA_FCR_RX_POOL_ID #define MCA_FCR_RX_POOL_ID HCI_ACL_POOL_ID #endif /* GKI Buffer Pool ID used to hold MPS segments used in (re)transmissions. L2CAP_DEFAULT_ERM_POOL_ID is specified to use the HCI ACL data pool. Note: This pool needs to have enough buffers to hold two times the window size negotiated in the tL2CAP_FCR_OPTIONS (2 * tx_win_size) to allow for retransmissions. The size of each buffer must be able to hold the maximum MPS segment size passed in tL2CAP_FCR_OPTIONS plus BT_HDR (8) + HCI preamble (4) + L2CAP_MIN_OFFSET (11 - as of BT 2.1 + EDR Spec). */ #ifndef MCA_FCR_TX_POOL_ID #define MCA_FCR_TX_POOL_ID HCI_ACL_POOL_ID #endif /* MCAP control channel FCR Option: Size of the transmission window when using enhanced retransmission mode. 1 is defined by HDP specification for control channel. */ #ifndef MCA_FCR_OPT_TX_WINDOW_SIZE #define MCA_FCR_OPT_TX_WINDOW_SIZE 1 #endif /* MCAP control channel FCR Option: Number of transmission attempts for a single I-Frame before taking Down the connection. Used In ERTM mode only. Value is Ignored in basic and Streaming modes. Range: 0, 1-0xFF 0 - infinite retransmissions 1 - single transmission */ #ifndef MCA_FCR_OPT_MAX_TX_B4_DISCNT #define MCA_FCR_OPT_MAX_TX_B4_DISCNT 20 #endif /* MCAP control channel FCR Option: Retransmission Timeout The AVRCP specification set a value in the range of 300 - 2000 ms Timeout (in msecs) to detect Lost I-Frames. Only used in Enhanced retransmission mode. Range: Minimum 2000 (2 secs) when supporting PBF. */ #ifndef MCA_FCR_OPT_RETX_TOUT #define MCA_FCR_OPT_RETX_TOUT 2000 #endif /* MCAP control channel FCR Option: Monitor Timeout The AVRCP specification set a value in the range of 300 - 2000 ms Timeout (in msecs) to detect Lost S-Frames. Only used in Enhanced retransmission mode. Range: Minimum 12000 (12 secs) when supporting PBF. */ #ifndef MCA_FCR_OPT_MONITOR_TOUT #define MCA_FCR_OPT_MONITOR_TOUT 12000 #endif /* MCAP control channel FCR Option: Maximum PDU payload size. The maximum number of payload octets that the local device can receive in a single PDU. */ #ifndef MCA_FCR_OPT_MPS_SIZE #define MCA_FCR_OPT_MPS_SIZE 1000 #endif /* Shared transport */ #ifndef NFC_SHARED_TRANSPORT_ENABLED #define NFC_SHARED_TRANSPORT_ENABLED FALSE #endif /****************************************************************************** ** ** Sleep Mode (Low Power Mode) ** ******************************************************************************/ #ifndef HCILP_INCLUDED #define HCILP_INCLUDED TRUE #endif /****************************************************************************** ** ** APPL - Application Task ** ******************************************************************************/ #define L2CAP_FEATURE_REQ_ID 73 #define L2CAP_FEATURE_RSP_ID 173 /****************************************************************************** ** ** BTA ** ******************************************************************************/ /* BTA EIR canned UUID list (default is dynamic) */ #ifndef BTA_EIR_CANNED_UUID_LIST #define BTA_EIR_CANNED_UUID_LIST FALSE #endif /* Number of supported customer UUID in EIR */ #ifndef BTA_EIR_SERVER_NUM_CUSTOM_UUID #define BTA_EIR_SERVER_NUM_CUSTOM_UUID 8 #endif /* CHLD override for bluedroid */ #ifndef BTA_AG_CHLD_VAL_ECC #define BTA_AG_CHLD_VAL_ECC "(0,1,1x,2,2x,3)" #endif #ifndef BTA_AG_CHLD_VAL #define BTA_AG_CHLD_VAL "(0,1,2,3)" #endif /* Set the CIND to match HFP 1.5 */ #ifndef BTA_AG_CIND_INFO #define BTA_AG_CIND_INFO "(\"call\",(0,1)),(\"callsetup\",(0-3)),(\"service\",(0-1)),(\"signal\",(0-5)),(\"roam\",(0,1)),(\"battchg\",(0-5)),(\"callheld\",(0-2))" #endif #ifndef BTA_DM_AVOID_A2DP_ROLESWITCH_ON_INQUIRY #define BTA_DM_AVOID_A2DP_ROLESWITCH_ON_INQUIRY TRUE #endif /****************************************************************************** ** ** Tracing: Include trace header file here. ** ******************************************************************************/ /* Enable/disable BTSnoop memory logging */ #ifndef BTSNOOP_MEM #define BTSNOOP_MEM TRUE #endif #include "bt_trace.h" #endif /* BT_TARGET_H */