1 /****************************************************************************** 2 * 3 * Copyright (C) 2003-2014 Broadcom Corporation 4 * 5 * Licensed under the Apache License, Version 2.0 (the "License"); 6 * you may not use this file except in compliance with the License. 7 * You may obtain a copy of the License at: 8 * 9 * http://www.apache.org/licenses/LICENSE-2.0 10 * 11 * Unless required by applicable law or agreed to in writing, software 12 * distributed under the License is distributed on an "AS IS" BASIS, 13 * WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied. 14 * See the License for the specific language governing permissions and 15 * limitations under the License. 16 * 17 ******************************************************************************/ 18 19 /****************************************************************************** 20 * 21 * This is the public interface file for BTA, Broadcom's Bluetooth 22 * application layer for mobile phones. 23 * 24 ******************************************************************************/ 25 #ifndef BTA_API_H 26 #define BTA_API_H 27 28 #include "bt_target.h" 29 #include "bt_types.h" 30 #include "btm_api.h" 31 32 #if BLE_INCLUDED == TRUE 33 #include "btm_ble_api.h" 34 #endif 35 36 /***************************************************************************** 37 ** Constants and data types 38 *****************************************************************************/ 39 40 /* Status Return Value */ 41 #define BTA_SUCCESS 0 /* Successful operation. */ 42 #define BTA_FAILURE 1 /* Generic failure. */ 43 #define BTA_PENDING 2 /* API cannot be completed right now */ 44 #define BTA_BUSY 3 45 #define BTA_NO_RESOURCES 4 46 #define BTA_WRONG_MODE 5 47 48 typedef UINT8 tBTA_STATUS; 49 50 /* 51 * Service ID 52 * 53 * NOTES: When you add a new Service ID for BTA AND require to change the value of BTA_MAX_SERVICE_ID, 54 * make sure that the correct security ID of the new service from Security service definitions (btm_api.h) 55 * should be added to bta_service_id_to_btm_srv_id_lkup_tbl table in bta_dm_act.c. 56 */ 57 58 #define BTA_RES_SERVICE_ID 0 /* Reserved */ 59 #define BTA_SPP_SERVICE_ID 1 /* Serial port profile. */ 60 #define BTA_DUN_SERVICE_ID 2 /* Dial-up networking profile. */ 61 #define BTA_A2DP_SOURCE_SERVICE_ID 3 /* A2DP Source profile. */ 62 #define BTA_LAP_SERVICE_ID 4 /* LAN access profile. */ 63 #define BTA_HSP_SERVICE_ID 5 /* Headset profile. */ 64 #define BTA_HFP_SERVICE_ID 6 /* Hands-free profile. */ 65 #define BTA_OPP_SERVICE_ID 7 /* Object push */ 66 #define BTA_FTP_SERVICE_ID 8 /* File transfer */ 67 #define BTA_CTP_SERVICE_ID 9 /* Cordless Terminal */ 68 #define BTA_ICP_SERVICE_ID 10 /* Intercom Terminal */ 69 #define BTA_SYNC_SERVICE_ID 11 /* Synchronization */ 70 #define BTA_BPP_SERVICE_ID 12 /* Basic printing profile */ 71 #define BTA_BIP_SERVICE_ID 13 /* Basic Imaging profile */ 72 #define BTA_PANU_SERVICE_ID 14 /* PAN User */ 73 #define BTA_NAP_SERVICE_ID 15 /* PAN Network access point */ 74 #define BTA_GN_SERVICE_ID 16 /* PAN Group Ad-hoc networks */ 75 #define BTA_SAP_SERVICE_ID 17 /* SIM Access profile */ 76 #define BTA_A2DP_SINK_SERVICE_ID 18 /* A2DP Sink */ 77 #define BTA_AVRCP_SERVICE_ID 19 /* A/V remote control */ 78 #define BTA_HID_SERVICE_ID 20 /* HID */ 79 #define BTA_VDP_SERVICE_ID 21 /* Video distribution */ 80 #define BTA_PBAP_SERVICE_ID 22 /* PhoneBook Access Server*/ 81 #define BTA_HSP_HS_SERVICE_ID 23 /* HFP HS role */ 82 #define BTA_HFP_HS_SERVICE_ID 24 /* HSP HS role */ 83 #define BTA_MAP_SERVICE_ID 25 /* Message Access Profile */ 84 #define BTA_MN_SERVICE_ID 26 /* Message Notification Service */ 85 #define BTA_HDP_SERVICE_ID 27 /* Health Device Profile */ 86 #define BTA_PCE_SERVICE_ID 28 /* PhoneBook Access Client*/ 87 #define BTA_SDP_SERVICE_ID 29 /* SDP Search*/ 88 #if BLE_INCLUDED == TRUE && BTA_GATT_INCLUDED == TRUE 89 /* BLE profile service ID */ 90 #define BTA_BLE_SERVICE_ID 30 /* GATT profile */ 91 92 #define BTA_USER_SERVICE_ID 31 /* User requested UUID */ 93 94 #define BTA_MAX_SERVICE_ID 32 95 #else 96 #define BTA_USER_SERVICE_ID 30 /* User requested UUID */ 97 #define BTA_MAX_SERVICE_ID 31 98 #endif 99 /* service IDs (BTM_SEC_SERVICE_FIRST_EMPTY + 1) to (BTM_SEC_MAX_SERVICES - 1) 100 * are used by BTA JV */ 101 #define BTA_FIRST_JV_SERVICE_ID (BTM_SEC_SERVICE_FIRST_EMPTY + 1) 102 #define BTA_LAST_JV_SERVICE_ID (BTM_SEC_MAX_SERVICES - 1) 103 104 typedef UINT8 tBTA_SERVICE_ID; 105 106 /* Service ID Mask */ 107 #define BTA_RES_SERVICE_MASK 0x00000001 /* Reserved */ 108 #define BTA_SPP_SERVICE_MASK 0x00000002 /* Serial port profile. */ 109 #define BTA_DUN_SERVICE_MASK 0x00000004 /* Dial-up networking profile. */ 110 #define BTA_FAX_SERVICE_MASK 0x00000008 /* Fax profile. */ 111 #define BTA_LAP_SERVICE_MASK 0x00000010 /* LAN access profile. */ 112 #define BTA_HSP_SERVICE_MASK 0x00000020 /* HSP AG role. */ 113 #define BTA_HFP_SERVICE_MASK 0x00000040 /* HFP AG role */ 114 #define BTA_OPP_SERVICE_MASK 0x00000080 /* Object push */ 115 #define BTA_FTP_SERVICE_MASK 0x00000100 /* File transfer */ 116 #define BTA_CTP_SERVICE_MASK 0x00000200 /* Cordless Terminal */ 117 #define BTA_ICP_SERVICE_MASK 0x00000400 /* Intercom Terminal */ 118 #define BTA_SYNC_SERVICE_MASK 0x00000800 /* Synchronization */ 119 #define BTA_BPP_SERVICE_MASK 0x00001000 /* Print server */ 120 #define BTA_BIP_SERVICE_MASK 0x00002000 /* Basic Imaging */ 121 #define BTA_PANU_SERVICE_MASK 0x00004000 /* PAN User */ 122 #define BTA_NAP_SERVICE_MASK 0x00008000 /* PAN Network access point */ 123 #define BTA_GN_SERVICE_MASK 0x00010000 /* PAN Group Ad-hoc networks */ 124 #define BTA_SAP_SERVICE_MASK 0x00020000 /* PAN Group Ad-hoc networks */ 125 #define BTA_A2DP_SERVICE_MASK 0x00040000 /* Advanced audio distribution */ 126 #define BTA_AVRCP_SERVICE_MASK 0x00080000 /* A/V remote control */ 127 #define BTA_HID_SERVICE_MASK 0x00100000 /* HID */ 128 #define BTA_VDP_SERVICE_MASK 0x00200000 /* Video distribution */ 129 #define BTA_PBAP_SERVICE_MASK 0x00400000 /* Phone Book Server */ 130 #define BTA_HSP_HS_SERVICE_MASK 0x00800000 /* HFP HS role */ 131 #define BTA_HFP_HS_SERVICE_MASK 0x01000000 /* HSP HS role */ 132 #define BTA_MAS_SERVICE_MASK 0x02000000 /* Message Access Profile */ 133 #define BTA_MN_SERVICE_MASK 0x04000000 /* Message Notification Profile */ 134 #define BTA_HL_SERVICE_MASK 0x08000000 /* Health Device Profile */ 135 #define BTA_PCE_SERVICE_MASK 0x10000000 /* Phone Book Client */ 136 137 #if BLE_INCLUDED == TRUE && BTA_GATT_INCLUDED == TRUE 138 #define BTA_BLE_SERVICE_MASK 0x20000000 /* GATT based service */ 139 #define BTA_USER_SERVICE_MASK 0x40000000 /* Message Notification Profile */ 140 #else 141 #define BTA_USER_SERVICE_MASK 0x20000000 /* Message Notification Profile */ 142 #endif 143 144 #if BLE_INCLUDED == TRUE && BTA_GATT_INCLUDED == TRUE 145 #define BTA_ALL_SERVICE_MASK 0x3FFFFFFF /* All services supported by BTA. */ 146 #else 147 #define BTA_ALL_SERVICE_MASK 0x1FFFFFFF /* All services supported by BTA. */ 148 #endif 149 150 typedef UINT32 tBTA_SERVICE_MASK; 151 152 /* extended service mask, including mask with one or more GATT UUID */ 153 typedef struct 154 { 155 tBTA_SERVICE_MASK srvc_mask; 156 UINT8 num_uuid; 157 tBT_UUID *p_uuid; 158 }tBTA_SERVICE_MASK_EXT; 159 160 /* Security Setting Mask */ 161 #define BTA_SEC_NONE BTM_SEC_NONE /* No security. */ 162 #define BTA_SEC_AUTHORIZE (BTM_SEC_IN_AUTHORIZE ) /* Authorization required (only needed for out going connection )*/ 163 #define BTA_SEC_AUTHENTICATE (BTM_SEC_IN_AUTHENTICATE | BTM_SEC_OUT_AUTHENTICATE) /* Authentication required. */ 164 #define BTA_SEC_ENCRYPT (BTM_SEC_IN_ENCRYPT | BTM_SEC_OUT_ENCRYPT) /* Encryption required. */ 165 #define BTA_SEC_MODE4_LEVEL4 (BTM_SEC_MODE4_LEVEL4) /* Mode 4 level 4 service, i.e. incoming/outgoing MITM and P-256 encryption */ 166 #define BTA_SEC_MITM (BTM_SEC_IN_MITM | BTM_SEC_OUT_MITM) /* Man-In-The_Middle protection */ 167 #define BTA_SEC_IN_16_DIGITS (BTM_SEC_IN_MIN_16_DIGIT_PIN) /* Min 16 digit for pin code */ 168 169 typedef UINT16 tBTA_SEC; 170 171 /* Ignore for Discoverable, Connectable, Pairable and Connectable Paired only device modes */ 172 #define BTA_DM_IGNORE 0x00FF 173 174 /* Ignore for Discoverable, Connectable only for LE modes */ 175 #define BTA_DM_LE_IGNORE 0xFF00 176 177 #define BTA_APP_ID_PAN_MULTI 0xFE /* app id for pan multiple connection */ 178 #define BTA_ALL_APP_ID 0xFF 179 180 /* Discoverable Modes */ 181 #define BTA_DM_NON_DISC BTM_NON_DISCOVERABLE /* Device is not discoverable. */ 182 #define BTA_DM_GENERAL_DISC BTM_GENERAL_DISCOVERABLE /* General discoverable. */ 183 #define BTA_DM_LIMITED_DISC BTM_LIMITED_DISCOVERABLE /* Limited discoverable. */ 184 #if ((defined BLE_INCLUDED) && (BLE_INCLUDED == TRUE)) 185 #define BTA_DM_BLE_NON_DISCOVERABLE BTM_BLE_NON_DISCOVERABLE /* Device is not LE discoverable */ 186 #define BTA_DM_BLE_GENERAL_DISCOVERABLE BTM_BLE_GENERAL_DISCOVERABLE /* Device is LE General discoverable */ 187 #define BTA_DM_BLE_LIMITED_DISCOVERABLE BTM_BLE_LIMITED_DISCOVERABLE /* Device is LE Limited discoverable */ 188 #endif 189 typedef UINT16 tBTA_DM_DISC; /* this discoverability mode is a bit mask among BR mode and LE mode */ 190 191 /* Connectable Modes */ 192 #define BTA_DM_NON_CONN BTM_NON_CONNECTABLE /* Device is not connectable. */ 193 #define BTA_DM_CONN BTM_CONNECTABLE /* Device is connectable. */ 194 #if ((defined BLE_INCLUDED) && (BLE_INCLUDED == TRUE)) 195 #define BTA_DM_BLE_NON_CONNECTABLE BTM_BLE_NON_CONNECTABLE /* Device is LE non-connectable. */ 196 #define BTA_DM_BLE_CONNECTABLE BTM_BLE_CONNECTABLE /* Device is LE connectable. */ 197 #endif 198 199 typedef UINT16 tBTA_DM_CONN; 200 201 #define BTA_TRANSPORT_UNKNOWN 0 202 #define BTA_TRANSPORT_BR_EDR BT_TRANSPORT_BR_EDR 203 #define BTA_TRANSPORT_LE BT_TRANSPORT_LE 204 typedef tBT_TRANSPORT tBTA_TRANSPORT; 205 206 /* Pairable Modes */ 207 #define BTA_DM_PAIRABLE 1 208 #define BTA_DM_NON_PAIRABLE 0 209 210 /* Connectable Paired Only Mode */ 211 #define BTA_DM_CONN_ALL 0 212 #define BTA_DM_CONN_PAIRED 1 213 214 /* Inquiry Modes */ 215 #define BTA_DM_INQUIRY_NONE BTM_INQUIRY_NONE /*No BR inquiry. */ 216 #define BTA_DM_GENERAL_INQUIRY BTM_GENERAL_INQUIRY /* Perform general inquiry. */ 217 #define BTA_DM_LIMITED_INQUIRY BTM_LIMITED_INQUIRY /* Perform limited inquiry. */ 218 219 #if ((defined BLE_INCLUDED) && (BLE_INCLUDED == TRUE)) 220 #define BTA_BLE_INQUIRY_NONE BTM_BLE_INQUIRY_NONE 221 #define BTA_BLE_GENERAL_INQUIRY BTM_BLE_GENERAL_INQUIRY /* Perform LE general inquiry. */ 222 #define BTA_BLE_LIMITED_INQUIRY BTM_BLE_LIMITED_INQUIRY /* Perform LE limited inquiry. */ 223 #endif 224 typedef UINT8 tBTA_DM_INQ_MODE; 225 226 /* Inquiry Filter Type */ 227 #define BTA_DM_INQ_CLR BTM_CLR_INQUIRY_FILTER /* Clear inquiry filter. */ 228 #define BTA_DM_INQ_DEV_CLASS BTM_FILTER_COND_DEVICE_CLASS /* Filter on device class. */ 229 #define BTA_DM_INQ_BD_ADDR BTM_FILTER_COND_BD_ADDR /* Filter on a specific BD address. */ 230 231 typedef UINT8 tBTA_DM_INQ_FILT; 232 233 /* Authorize Response */ 234 #define BTA_DM_AUTH_PERM 0 /* Authorized for future connections to the service */ 235 #define BTA_DM_AUTH_TEMP 1 /* Authorized for current connection only */ 236 #define BTA_DM_NOT_AUTH 2 /* Not authorized for the service */ 237 238 typedef UINT8 tBTA_AUTH_RESP; 239 240 /* M/S preferred roles */ 241 #define BTA_ANY_ROLE 0x00 242 #define BTA_MASTER_ROLE_PREF 0x01 243 #define BTA_MASTER_ROLE_ONLY 0x02 244 #define BTA_SLAVE_ROLE_ONLY 0x03 /* Used for PANU only, skip role switch to master */ 245 246 typedef UINT8 tBTA_PREF_ROLES; 247 248 enum 249 { 250 251 BTA_DM_NO_SCATTERNET, /* Device doesn't support scatternet, it might 252 support "role switch during connection" for 253 an incoming connection, when it already has 254 another connection in master role */ 255 BTA_DM_PARTIAL_SCATTERNET, /* Device supports partial scatternet. It can have 256 simulateous connection in Master and Slave roles 257 for short period of time */ 258 BTA_DM_FULL_SCATTERNET /* Device can have simultaneous connection in master 259 and slave roles */ 260 261 }; 262 263 264 /* Inquiry filter device class condition */ 265 typedef struct 266 { 267 DEV_CLASS dev_class; /* device class of interest */ 268 DEV_CLASS dev_class_mask; /* mask to determine the bits of device class of interest */ 269 } tBTA_DM_COD_COND; 270 271 272 /* Inquiry Filter Condition */ 273 typedef union 274 { 275 BD_ADDR bd_addr; /* BD address of device to filter. */ 276 tBTA_DM_COD_COND dev_class_cond; /* Device class filter condition */ 277 } tBTA_DM_INQ_COND; 278 279 /* Inquiry Parameters */ 280 typedef struct 281 { 282 tBTA_DM_INQ_MODE mode; /* Inquiry mode, limited or general. */ 283 UINT8 duration; /* Inquiry duration in 1.28 sec units. */ 284 UINT8 max_resps; /* Maximum inquiry responses. Set to zero for unlimited responses. */ 285 BOOLEAN report_dup; /* report duplicated inquiry response with higher RSSI value */ 286 tBTA_DM_INQ_FILT filter_type; /* Filter condition type. */ 287 tBTA_DM_INQ_COND filter_cond; /* Filter condition data. */ 288 #if (defined(BTA_HOST_INTERLEAVE_SEARCH) && BTA_HOST_INTERLEAVE_SEARCH == TRUE) 289 UINT8 intl_duration[4];/*duration array storing the interleave scan's time portions*/ 290 #endif 291 } tBTA_DM_INQ; 292 293 typedef struct 294 { 295 UINT8 bta_dm_eir_min_name_len; /* minimum length of local name when it is shortened */ 296 #if (BTA_EIR_CANNED_UUID_LIST == TRUE) 297 UINT8 bta_dm_eir_uuid16_len; /* length of 16-bit UUIDs */ 298 UINT8 *bta_dm_eir_uuid16; /* 16-bit UUIDs */ 299 #else 300 UINT32 uuid_mask[BTM_EIR_SERVICE_ARRAY_SIZE]; /* mask of UUID list in EIR */ 301 #endif 302 INT8 *bta_dm_eir_inq_tx_power; /* Inquiry TX power */ 303 UINT8 bta_dm_eir_flag_len; /* length of flags in bytes */ 304 UINT8 *bta_dm_eir_flags; /* flags for EIR */ 305 UINT8 bta_dm_eir_manufac_spec_len; /* length of manufacturer specific in bytes */ 306 UINT8 *bta_dm_eir_manufac_spec; /* manufacturer specific */ 307 UINT8 bta_dm_eir_additional_len; /* length of additional data in bytes */ 308 UINT8 *bta_dm_eir_additional; /* additional data */ 309 } tBTA_DM_EIR_CONF; 310 311 #if BLE_INCLUDED == TRUE 312 /* ADV data flag bit definition used for BTM_BLE_AD_TYPE_FLAG */ 313 #define BTA_BLE_LIMIT_DISC_FLAG BTM_BLE_LIMIT_DISC_FLAG 314 #define BTA_BLE_GEN_DISC_FLAG BTM_BLE_GEN_DISC_FLAG 315 #define BTA_BLE_BREDR_NOT_SPT BTM_BLE_BREDR_NOT_SPT 316 #define BTA_BLE_DMT_CONTROLLER_SPT BTM_BLE_DMT_CONTROLLER_SPT 317 #define BTA_BLE_DMT_HOST_SPT BTM_BLE_DMT_HOST_SPT 318 #define BTA_BLE_NON_LIMIT_DISC_FLAG BTM_BLE_NON_LIMIT_DISC_FLAG 319 #define BTA_BLE_ADV_FLAG_MASK BTM_BLE_ADV_FLAG_MASK 320 #define BTA_BLE_LIMIT_DISC_MASK BTM_BLE_LIMIT_DISC_MASK 321 322 /* ADV data bit mask */ 323 #define BTA_BLE_AD_BIT_DEV_NAME BTM_BLE_AD_BIT_DEV_NAME 324 #define BTA_BLE_AD_BIT_FLAGS BTM_BLE_AD_BIT_FLAGS 325 #define BTA_BLE_AD_BIT_MANU BTM_BLE_AD_BIT_MANU 326 #define BTA_BLE_AD_BIT_TX_PWR BTM_BLE_AD_BIT_TX_PWR 327 #define BTA_BLE_AD_BIT_INT_RANGE BTM_BLE_AD_BIT_INT_RANGE 328 #define BTA_BLE_AD_BIT_SERVICE BTM_BLE_AD_BIT_SERVICE 329 #define BTA_BLE_AD_BIT_APPEARANCE BTM_BLE_AD_BIT_APPEARANCE 330 #define BTA_BLE_AD_BIT_PROPRIETARY BTM_BLE_AD_BIT_PROPRIETARY 331 #define BTA_DM_BLE_AD_BIT_SERVICE_SOL BTM_BLE_AD_BIT_SERVICE_SOL 332 #define BTA_DM_BLE_AD_BIT_SERVICE_DATA BTM_BLE_AD_BIT_SERVICE_DATA 333 #define BTA_DM_BLE_AD_BIT_SIGN_DATA BTM_BLE_AD_BIT_SIGN_DATA 334 #define BTA_DM_BLE_AD_BIT_SERVICE_128SOL BTM_BLE_AD_BIT_SERVICE_128SOL 335 #define BTA_DM_BLE_AD_BIT_PUBLIC_ADDR BTM_BLE_AD_BIT_PUBLIC_ADDR 336 #define BTA_DM_BLE_AD_BIT_RANDOM_ADDR BTM_BLE_AD_BIT_RANDOM_ADDR 337 #define BTA_DM_BLE_AD_BIT_SERVICE_128 BTM_BLE_AD_BIT_SERVICE_128 /*128-bit Service UUIDs*/ 338 339 typedef tBTM_BLE_AD_MASK tBTA_BLE_AD_MASK; 340 typedef tBTM_BLE_INT_RANGE tBTA_BLE_INT_RANGE; 341 typedef tBTM_BLE_SERVICE tBTA_BLE_SERVICE; 342 typedef tBTM_BLE_PROP_ELEM tBTA_BLE_PROP_ELEM; 343 typedef tBTM_BLE_PROPRIETARY tBTA_BLE_PROPRIETARY; 344 typedef tBTM_BLE_MANU tBTA_BLE_MANU; 345 typedef tBTM_BLE_SERVICE_DATA tBTA_BLE_SERVICE_DATA; 346 typedef tBTM_BLE_128SERVICE tBTA_BLE_128SERVICE; 347 typedef tBTM_BLE_32SERVICE tBTA_BLE_32SERVICE; 348 349 typedef struct 350 { 351 tBTA_BLE_INT_RANGE int_range; /* slave prefered conn interval range */ 352 tBTA_BLE_MANU manu; /* manufacturer data */ 353 tBTA_BLE_SERVICE services; /* 16 bits services */ 354 tBTA_BLE_128SERVICE services_128b; /* 128 bits service */ 355 tBTA_BLE_32SERVICE service_32b; /* 32 bits Service UUID */ 356 tBTA_BLE_SERVICE sol_services; /* 16 bits services Solicitation UUIDs */ 357 tBTA_BLE_32SERVICE sol_service_32b; /* List of 32 bit Service Solicitation UUIDs */ 358 tBTA_BLE_128SERVICE sol_service_128b;/* List of 128 bit Service Solicitation UUIDs */ 359 tBTA_BLE_PROPRIETARY proprietary; /* proprietary data */ 360 tBTA_BLE_SERVICE_DATA service_data; /* service data */ 361 UINT16 appearance; /* appearance data */ 362 UINT8 flag; 363 UINT8 tx_power; 364 }tBTA_BLE_ADV_DATA; 365 366 typedef void (tBTA_SET_ADV_DATA_CMPL_CBACK) (tBTA_STATUS status); 367 368 /* advertising channel map */ 369 #define BTA_BLE_ADV_CHNL_37 BTM_BLE_ADV_CHNL_37 370 #define BTA_BLE_ADV_CHNL_38 BTM_BLE_ADV_CHNL_38 371 #define BTA_BLE_ADV_CHNL_39 BTM_BLE_ADV_CHNL_39 372 typedef tBTM_BLE_ADV_CHNL_MAP tBTA_BLE_ADV_CHNL_MAP; /* use as a bit mask */ 373 374 /* advertising filter policy */ 375 typedef tBTM_BLE_AFP tBTA_BLE_AFP; 376 377 /* adv event type */ 378 #define BTA_BLE_CONNECT_EVT BTM_BLE_CONNECT_EVT /* Connectable undirected advertising */ 379 #define BTA_BLE_CONNECT_DIR_EVT BTM_BLE_CONNECT_DIR_EVT /* Connectable directed advertising */ 380 #define BTA_BLE_DISCOVER_EVT BTM_BLE_DISCOVER_EVT /* Scannable undirected advertising */ 381 #define BTA_BLE_NON_CONNECT_EVT BTM_BLE_NON_CONNECT_EVT /* Non connectable undirected advertising */ 382 typedef UINT8 tBTA_BLE_ADV_EVT; 383 384 /* adv tx power level */ 385 #define BTA_BLE_ADV_TX_POWER_MIN 0 /* minimum tx power */ 386 #define BTA_BLE_ADV_TX_POWER_LOW 1 /* low tx power */ 387 #define BTA_BLE_ADV_TX_POWER_MID 2 /* middle tx power */ 388 #define BTA_BLE_ADV_TX_POWER_UPPER 3 /* upper tx power */ 389 #define BTA_BLE_ADV_TX_POWER_MAX 4 /* maximum tx power */ 390 typedef UINT8 tBTA_BLE_ADV_TX_POWER; 391 392 /* advertising instance parameters */ 393 typedef struct 394 { 395 UINT16 adv_int_min; /* minimum adv interval */ 396 UINT16 adv_int_max; /* maximum adv interval */ 397 tBTA_BLE_ADV_EVT adv_type; /* adv event type */ 398 tBTA_BLE_ADV_CHNL_MAP channel_map; /* adv channel map */ 399 tBTA_BLE_AFP adv_filter_policy; /* advertising filter policy */ 400 tBTA_BLE_ADV_TX_POWER tx_power; /* adv tx power */ 401 }tBTA_BLE_ADV_PARAMS; 402 403 /* These are the fields returned in each device adv packet. It 404 ** is returned in the results callback if registered. 405 */ 406 typedef struct 407 { 408 UINT8 conn_mode; 409 tBTA_BLE_AD_MASK ad_mask; /* mask of the valid adv data field */ 410 UINT8 flag; 411 UINT8 tx_power_level; 412 UINT8 remote_name_len; 413 UINT8 *p_remote_name; 414 tBTA_BLE_SERVICE service; 415 } tBTA_BLE_INQ_DATA; 416 417 enum 418 { 419 BTA_BLE_BATCH_SCAN_MODE_PASS = 1, 420 BTA_BLE_BATCH_SCAN_MODE_ACTI = 2, 421 BTA_BLE_BATCH_SCAN_MODE_PASS_ACTI = 3 422 }; 423 typedef UINT8 tBTA_BLE_BATCH_SCAN_MODE; 424 425 enum 426 { 427 BTA_BLE_DISCARD_OLD_ITEMS=0, 428 BTA_BLE_DISCARD_LOWER_RSSI_ITEMS=1 429 }; 430 typedef UINT8 tBTA_BLE_DISCARD_RULE; 431 432 enum 433 { 434 BTA_BLE_ADV_SEEN_FIRST_TIME=0, 435 BTA_BLE_ADV_TRACKING_TIMEOUT=1 436 }; 437 typedef UINT8 tBTA_BLE_ADV_CHANGE_REASON; 438 439 enum 440 { 441 BTA_BLE_BATCH_SCAN_ENB_EVT = 1, 442 BTA_BLE_BATCH_SCAN_CFG_STRG_EVT = 2, 443 BTA_BLE_BATCH_SCAN_DATA_EVT = 3, 444 BTA_BLE_BATCH_SCAN_THRES_EVT = 4, 445 BTA_BLE_BATCH_SCAN_PARAM_EVT = 5, 446 BTA_BLE_BATCH_SCAN_DIS_EVT = 6 447 }; 448 typedef tBTM_BLE_BATCH_SCAN_EVT tBTA_BLE_BATCH_SCAN_EVT; 449 450 typedef tBTM_BLE_TRACK_ADV_ACTION tBTA_BLE_TRACK_ADV_ACTION; 451 #endif 452 453 /* BLE customer specific feature function type definitions */ 454 /* data type used on customer specific feature for RSSI monitoring */ 455 #define BTA_BLE_RSSI_ALERT_HI 0 456 #define BTA_BLE_RSSI_ALERT_RANGE 1 457 #define BTA_BLE_RSSI_ALERT_LO 2 458 typedef UINT8 tBTA_DM_BLE_RSSI_ALERT_TYPE; 459 460 #define BTA_BLE_RSSI_ALERT_NONE BTM_BLE_RSSI_ALERT_NONE /* (0) */ 461 #define BTA_BLE_RSSI_ALERT_HI_BIT BTM_BLE_RSSI_ALERT_HI_BIT /* (1) */ 462 #define BTA_BLE_RSSI_ALERT_RANGE_BIT BTM_BLE_RSSI_ALERT_RANGE_BIT /* (1 << 1) */ 463 #define BTA_BLE_RSSI_ALERT_LO_BIT BTM_BLE_RSSI_ALERT_LO_BIT /* (1 << 2) */ 464 typedef UINT8 tBTA_DM_BLE_RSSI_ALERT_MASK; 465 466 467 typedef void (tBTA_DM_BLE_RSSI_CBACK) (BD_ADDR bd_addr, tBTA_DM_BLE_RSSI_ALERT_TYPE alert_type, INT8 rssi); 468 469 /* max number of filter spot for different filter type */ 470 #define BTA_DM_BLE_MAX_UUID_FILTER BTM_BLE_MAX_UUID_FILTER /* 8 */ 471 #define BTA_DM_BLE_MAX_ADDR_FILTER BTM_BLE_MAX_ADDR_FILTER /* 8 */ 472 #define BTA_DM_BLE_PF_STR_COND_MAX BTM_BLE_PF_STR_COND_MAX /* 4 apply to manu data , or local name */ 473 #define BTA_DM_BLE_PF_STR_LEN_MAX BTM_BLE_PF_STR_LEN_MAX /* match for first 20 bytes */ 474 475 #define BTA_DM_BLE_PF_LOGIC_OR 0 476 #define BTA_DM_BLE_PF_LOGIC_AND 1 477 typedef UINT8 tBTA_DM_BLE_PF_LOGIC_TYPE; 478 479 enum 480 { 481 BTA_DM_BLE_SCAN_COND_ADD, 482 BTA_DM_BLE_SCAN_COND_DELETE, 483 BTA_DM_BLE_SCAN_COND_CLEAR = 2 484 }; 485 typedef UINT8 tBTA_DM_BLE_SCAN_COND_OP; 486 487 /* ADV payload filtering vendor specific call event */ 488 enum 489 { 490 BTA_BLE_SCAN_PF_ENABLE_EVT = 7, 491 BTA_BLE_SCAN_PF_COND_EVT 492 }; 493 494 /* filter selection bit index */ 495 #define BTA_DM_BLE_PF_ADDR_FILTER BTM_BLE_PF_ADDR_FILTER 496 #define BTA_DM_BLE_PF_SRVC_DATA BTM_BLE_PF_SRVC_DATA 497 #define BTA_DM_BLE_PF_SRVC_UUID BTM_BLE_PF_SRVC_UUID 498 #define BTA_DM_BLE_PF_SRVC_SOL_UUID BTM_BLE_PF_SRVC_SOL_UUID 499 #define BTA_DM_BLE_PF_LOCAL_NAME BTM_BLE_PF_LOCAL_NAME 500 #define BTA_DM_BLE_PF_MANU_DATA BTM_BLE_PF_MANU_DATA 501 #define BTA_DM_BLE_PF_SRVC_DATA_PATTERN BTM_BLE_PF_SRVC_DATA_PATTERN 502 #define BTA_DM_BLE_PF_TYPE_ALL BTM_BLE_PF_TYPE_ALL 503 #define BTA_DM_BLE_PF_TYPE_MAX BTM_BLE_PF_TYPE_MAX 504 typedef UINT8 tBTA_DM_BLE_PF_COND_TYPE; 505 506 typedef union 507 { 508 UINT16 uuid16_mask; 509 UINT32 uuid32_mask; 510 UINT8 uuid128_mask[LEN_UUID_128]; 511 }tBTA_DM_BLE_PF_COND_MASK; 512 513 typedef struct 514 { 515 tBLE_BD_ADDR *p_target_addr; /* target address, if NULL, generic UUID filter */ 516 tBT_UUID uuid; /* UUID condition */ 517 tBTA_DM_BLE_PF_LOGIC_TYPE cond_logic; /* AND/OR */ 518 tBTA_DM_BLE_PF_COND_MASK *p_uuid_mask; /* UUID condition mask, if NULL, match exact as UUID condition */ 519 }tBTA_DM_BLE_PF_UUID_COND; 520 521 typedef struct 522 { 523 UINT8 data_len; /* <= 20 bytes */ 524 UINT8 *p_data; 525 }tBTA_DM_BLE_PF_LOCAL_NAME_COND; 526 527 typedef struct 528 { 529 UINT16 company_id; /* company ID */ 530 UINT8 data_len; /* <= 20 bytes */ 531 UINT8 *p_pattern; 532 UINT16 company_id_mask; /* UUID value mask */ 533 UINT8 *p_pattern_mask; /* Manufacturer data matching mask, same length 534 as data pattern, set to all 0xff, match exact data */ 535 }tBTA_DM_BLE_PF_MANU_COND; 536 537 typedef struct 538 { 539 UINT16 uuid; /* service ID */ 540 UINT8 data_len; /* <= 20 bytes */ 541 UINT8 *p_pattern; 542 UINT8 *p_pattern_mask; /* Service data matching mask, same length 543 as data pattern, set to all 0xff, match exact data */ 544 }tBTA_DM_BLE_PF_SRVC_PATTERN_COND; 545 546 typedef union 547 { 548 tBLE_BD_ADDR target_addr; 549 tBTA_DM_BLE_PF_LOCAL_NAME_COND local_name; /* lcoal name filtering */ 550 tBTA_DM_BLE_PF_MANU_COND manu_data; /* manufactuer data filtering */ 551 tBTA_DM_BLE_PF_UUID_COND srvc_uuid; /* service UUID filtering */ 552 tBTA_DM_BLE_PF_UUID_COND solicitate_uuid; /* solicitated service UUID filtering */ 553 tBTA_DM_BLE_PF_SRVC_PATTERN_COND srvc_data; /* service data pattern */ 554 }tBTA_DM_BLE_PF_COND_PARAM; 555 556 typedef UINT8 tBTA_DM_BLE_PF_FILT_INDEX; 557 typedef UINT8 tBTA_DM_BLE_PF_AVBL_SPACE; 558 559 typedef INT8 tBTA_DM_RSSI_VALUE; 560 typedef UINT8 tBTA_DM_LINK_QUALITY_VALUE; 561 562 563 typedef UINT8 tBTA_SIG_STRENGTH_MASK; 564 565 566 /* Security Callback Events */ 567 #define BTA_DM_ENABLE_EVT 0 /* Enable Event */ 568 #define BTA_DM_DISABLE_EVT 1 /* Disable Event */ 569 #define BTA_DM_PIN_REQ_EVT 2 /* PIN request. */ 570 #define BTA_DM_AUTH_CMPL_EVT 3 /* Authentication complete indication. */ 571 #define BTA_DM_AUTHORIZE_EVT 4 /* Authorization request. */ 572 #define BTA_DM_LINK_UP_EVT 5 /* Connection UP event */ 573 #define BTA_DM_LINK_DOWN_EVT 6 /* Connection DOWN event */ 574 #define BTA_DM_SIG_STRENGTH_EVT 7 /* Signal strength for bluetooth connection */ 575 #define BTA_DM_BUSY_LEVEL_EVT 8 /* System busy level */ 576 #define BTA_DM_BOND_CANCEL_CMPL_EVT 9 /* Bond cancel complete indication */ 577 #define BTA_DM_SP_CFM_REQ_EVT 10 /* Simple Pairing User Confirmation request. */ 578 #define BTA_DM_SP_KEY_NOTIF_EVT 11 /* Simple Pairing Passkey Notification */ 579 #define BTA_DM_SP_RMT_OOB_EVT 12 /* Simple Pairing Remote OOB Data request. */ 580 #define BTA_DM_SP_KEYPRESS_EVT 13 /* Key press notification event. */ 581 #define BTA_DM_ROLE_CHG_EVT 14 /* Role Change event. */ 582 #define BTA_DM_BLE_KEY_EVT 15 /* BLE SMP key event for peer device keys */ 583 #define BTA_DM_BLE_SEC_REQ_EVT 16 /* BLE SMP security request */ 584 #define BTA_DM_BLE_PASSKEY_NOTIF_EVT 17 /* SMP passkey notification event */ 585 #define BTA_DM_BLE_PASSKEY_REQ_EVT 18 /* SMP passkey request event */ 586 #define BTA_DM_BLE_OOB_REQ_EVT 19 /* SMP OOB request event */ 587 #define BTA_DM_BLE_LOCAL_IR_EVT 20 /* BLE local IR event */ 588 #define BTA_DM_BLE_LOCAL_ER_EVT 21 /* BLE local ER event */ 589 #define BTA_DM_BLE_NC_REQ_EVT 22 /* SMP Numeric Comparison request event */ 590 #define BTA_DM_SP_RMT_OOB_EXT_EVT 23 /* Simple Pairing Remote OOB Extended Data request. */ 591 #define BTA_DM_BLE_AUTH_CMPL_EVT 24 /* BLE Auth complete */ 592 #define BTA_DM_DEV_UNPAIRED_EVT 25 593 #define BTA_DM_HW_ERROR_EVT 26 /* BT Chip H/W error */ 594 #define BTA_DM_LE_FEATURES_READ 27 /* Cotroller specific LE features are read */ 595 #define BTA_DM_ENER_INFO_READ 28 /* Energy info read */ 596 typedef UINT8 tBTA_DM_SEC_EVT; 597 598 /* Structure associated with BTA_DM_ENABLE_EVT */ 599 typedef struct 600 { 601 tBTA_STATUS status; 602 } tBTA_DM_ENABLE; 603 604 /* Structure associated with BTA_DM_PIN_REQ_EVT */ 605 typedef struct 606 { 607 /* Note: First 3 data members must be, bd_addr, dev_class, and bd_name in order */ 608 BD_ADDR bd_addr; /* BD address peer device. */ 609 DEV_CLASS dev_class; /* Class of Device */ 610 BD_NAME bd_name; /* Name of peer device. */ 611 BOOLEAN min_16_digit; /* TRUE if the pin returned must be at least 16 digits */ 612 } tBTA_DM_PIN_REQ; 613 614 /* BLE related definition */ 615 616 #define BTA_DM_AUTH_FAIL_BASE (HCI_ERR_MAX_ERR + 10) 617 #define BTA_DM_AUTH_CONVERT_SMP_CODE(x) (BTA_DM_AUTH_FAIL_BASE + (x)) 618 #define BTA_DM_AUTH_SMP_PASSKEY_FAIL BTA_DM_AUTH_CONVERT_SMP_CODE (SMP_PASSKEY_ENTRY_FAIL) 619 #define BTA_DM_AUTH_SMP_OOB_FAIL (BTA_DM_AUTH_FAIL_BASE + SMP_OOB_FAIL) 620 #define BTA_DM_AUTH_SMP_PAIR_AUTH_FAIL (BTA_DM_AUTH_FAIL_BASE + SMP_PAIR_AUTH_FAIL) 621 #define BTA_DM_AUTH_SMP_CONFIRM_VALUE_FAIL (BTA_DM_AUTH_FAIL_BASE + SMP_CONFIRM_VALUE_ERR) 622 #define BTA_DM_AUTH_SMP_PAIR_NOT_SUPPORT (BTA_DM_AUTH_FAIL_BASE + SMP_PAIR_NOT_SUPPORT) 623 #define BTA_DM_AUTH_SMP_ENC_KEY_SIZE (BTA_DM_AUTH_FAIL_BASE + SMP_ENC_KEY_SIZE) 624 #define BTA_DM_AUTH_SMP_INVALID_CMD (BTA_DM_AUTH_FAIL_BASE + SMP_INVALID_CMD) 625 #define BTA_DM_AUTH_SMP_UNKNOWN_ERR (BTA_DM_AUTH_FAIL_BASE + SMP_PAIR_FAIL_UNKNOWN) 626 #define BTA_DM_AUTH_SMP_REPEATED_ATTEMPT (BTA_DM_AUTH_FAIL_BASE + SMP_REPEATED_ATTEMPTS) 627 #define BTA_DM_AUTH_SMP_INVALID_PARAMETERS (BTA_DM_AUTH_FAIL_BASE + SMP_INVALID_PARAMETERS) 628 #define BTA_DM_AUTH_SMP_INTERNAL_ERR (BTA_DM_AUTH_FAIL_BASE + SMP_PAIR_INTERNAL_ERR) 629 #define BTA_DM_AUTH_SMP_UNKNOWN_IO (BTA_DM_AUTH_FAIL_BASE + SMP_UNKNOWN_IO_CAP) 630 #define BTA_DM_AUTH_SMP_INIT_FAIL (BTA_DM_AUTH_FAIL_BASE + SMP_INIT_FAIL) 631 #define BTA_DM_AUTH_SMP_CONFIRM_FAIL (BTA_DM_AUTH_FAIL_BASE + SMP_CONFIRM_FAIL) 632 #define BTA_DM_AUTH_SMP_BUSY (BTA_DM_AUTH_FAIL_BASE + SMP_BUSY) 633 #define BTA_DM_AUTH_SMP_ENC_FAIL (BTA_DM_AUTH_FAIL_BASE + SMP_ENC_FAIL) 634 #define BTA_DM_AUTH_SMP_RSP_TIMEOUT (BTA_DM_AUTH_FAIL_BASE + SMP_RSP_TIMEOUT) 635 636 /* connection parameter boundary value and dummy value */ 637 #define BTA_DM_BLE_SCAN_INT_MIN BTM_BLE_SCAN_INT_MIN 638 #define BTA_DM_BLE_SCAN_INT_MAX BTM_BLE_SCAN_INT_MAX 639 #define BTA_DM_BLE_SCAN_WIN_MIN BTM_BLE_SCAN_WIN_MIN 640 #define BTA_DM_BLE_SCAN_WIN_MAX BTM_BLE_SCAN_WIN_MAX 641 #define BTA_DM_BLE_CONN_INT_MIN BTM_BLE_CONN_INT_MIN 642 #define BTA_DM_BLE_CONN_INT_MAX BTM_BLE_CONN_INT_MAX 643 #define BTA_DM_BLE_CONN_LATENCY_MAX BTM_BLE_CONN_LATENCY_MAX 644 #define BTA_DM_BLE_CONN_SUP_TOUT_MIN BTM_BLE_CONN_SUP_TOUT_MIN 645 #define BTA_DM_BLE_CONN_SUP_TOUT_MAX BTM_BLE_CONN_SUP_TOUT_MAX 646 #define BTA_DM_BLE_CONN_PARAM_UNDEF BTM_BLE_CONN_PARAM_UNDEF /* use this value when a specific value not to be overwritten */ 647 648 649 #define BTA_LE_KEY_PENC BTM_LE_KEY_PENC /* encryption information of peer device */ 650 #define BTA_LE_KEY_PID BTM_LE_KEY_PID /* identity key of the peer device */ 651 #define BTA_LE_KEY_PCSRK BTM_LE_KEY_PCSRK /* peer SRK */ 652 #define BTA_LE_KEY_LENC BTM_LE_KEY_LENC /* master role security information:div */ 653 #define BTA_LE_KEY_LID BTM_LE_KEY_LID /* master device ID key */ 654 #define BTA_LE_KEY_LCSRK BTM_LE_KEY_LCSRK /* local CSRK has been deliver to peer */ 655 typedef UINT8 tBTA_LE_KEY_TYPE; /* can be used as a bit mask */ 656 657 658 typedef tBTM_LE_PENC_KEYS tBTA_LE_PENC_KEYS ; 659 typedef tBTM_LE_PCSRK_KEYS tBTA_LE_PCSRK_KEYS; 660 typedef tBTM_LE_LENC_KEYS tBTA_LE_LENC_KEYS ; 661 typedef tBTM_LE_LCSRK_KEYS tBTA_LE_LCSRK_KEYS ; 662 typedef tBTM_LE_PID_KEYS tBTA_LE_PID_KEYS ; 663 664 typedef union 665 { 666 tBTA_LE_PENC_KEYS penc_key; /* received peer encryption key */ 667 tBTA_LE_PCSRK_KEYS psrk_key; /* received peer device SRK */ 668 tBTA_LE_PID_KEYS pid_key; /* peer device ID key */ 669 tBTA_LE_LENC_KEYS lenc_key; /* local encryption reproduction keys LTK = = d1(ER,DIV,0)*/ 670 tBTA_LE_LCSRK_KEYS lcsrk_key; /* local device CSRK = d1(ER,DIV,1)*/ 671 tBTA_LE_PID_KEYS lid_key; /* local device ID key for the particular remote */ 672 }tBTA_LE_KEY_VALUE; 673 674 #define BTA_BLE_LOCAL_KEY_TYPE_ID 1 675 #define BTA_BLE_LOCAL_KEY_TYPE_ER 2 676 typedef UINT8 tBTA_DM_BLE_LOCAL_KEY_MASK; 677 678 typedef struct 679 { 680 BT_OCTET16 ir; 681 BT_OCTET16 irk; 682 BT_OCTET16 dhk; 683 }tBTA_BLE_LOCAL_ID_KEYS; 684 685 #define BTA_DM_SEC_GRANTED BTA_SUCCESS 686 #define BTA_DM_SEC_PAIR_NOT_SPT BTA_DM_AUTH_SMP_PAIR_NOT_SUPPORT 687 #define BTA_DM_SEC_REP_ATTEMPTS BTA_DM_AUTH_SMP_REPEATED_ATTEMPT 688 typedef UINT8 tBTA_DM_BLE_SEC_GRANT; 689 690 691 #define BTA_DM_BLE_ONN_NONE BTM_BLE_CONN_NONE 692 #define BTA_DM_BLE_CONN_AUTO BTM_BLE_CONN_AUTO 693 #define BTA_DM_BLE_CONN_SELECTIVE BTM_BLE_CONN_SELECTIVE 694 typedef UINT8 tBTA_DM_BLE_CONN_TYPE; 695 696 typedef BOOLEAN (tBTA_DM_BLE_SEL_CBACK)(BD_ADDR random_bda, UINT8 *p_remote_name); 697 698 /* Structure associated with BTA_DM_BLE_SEC_REQ_EVT */ 699 typedef struct 700 { 701 BD_ADDR bd_addr; /* peer address */ 702 BD_NAME bd_name; /* peer device name */ 703 } tBTA_DM_BLE_SEC_REQ; 704 705 typedef struct 706 { 707 BD_ADDR bd_addr; /* peer address */ 708 tBTM_LE_KEY_TYPE key_type; 709 tBTM_LE_KEY_VALUE *p_key_value; 710 }tBTA_DM_BLE_KEY; 711 712 /* Structure associated with BTA_DM_AUTH_CMPL_EVT */ 713 typedef struct 714 { 715 BD_ADDR bd_addr; /* BD address peer device. */ 716 BD_NAME bd_name; /* Name of peer device. */ 717 BOOLEAN key_present; /* Valid link key value in key element */ 718 LINK_KEY key; /* Link key associated with peer device. */ 719 UINT8 key_type; /* The type of Link Key */ 720 BOOLEAN success; /* TRUE of authentication succeeded, FALSE if failed. */ 721 UINT8 fail_reason; /* The HCI reason/error code for when success=FALSE */ 722 tBLE_ADDR_TYPE addr_type; /* Peer device address type */ 723 tBT_DEVICE_TYPE dev_type; 724 } tBTA_DM_AUTH_CMPL; 725 726 727 /* Structure associated with BTA_DM_AUTHORIZE_EVT */ 728 typedef struct 729 { 730 BD_ADDR bd_addr; /* BD address peer device. */ 731 BD_NAME bd_name; /* Name of peer device. */ 732 tBTA_SERVICE_ID service; /* Service ID to authorize. */ 733 DEV_CLASS dev_class; 734 } tBTA_DM_AUTHORIZE; 735 736 /* Structure associated with BTA_DM_LINK_UP_EVT */ 737 typedef struct 738 { 739 BD_ADDR bd_addr; /* BD address peer device. */ 740 #if BLE_INCLUDED == TRUE 741 tBTA_TRANSPORT link_type; 742 #endif 743 } tBTA_DM_LINK_UP; 744 745 /* Structure associated with BTA_DM_LINK_DOWN_EVT */ 746 typedef struct 747 { 748 BD_ADDR bd_addr; /* BD address peer device. */ 749 UINT8 status; /* connection open/closed */ 750 BOOLEAN is_removed; /* TRUE if device is removed when link is down */ 751 #if BLE_INCLUDED == TRUE 752 tBTA_TRANSPORT link_type; 753 #endif 754 } tBTA_DM_LINK_DOWN; 755 756 /* Structure associated with BTA_DM_ROLE_CHG_EVT */ 757 typedef struct 758 { 759 BD_ADDR bd_addr; /* BD address peer device. */ 760 UINT8 new_role; /* the new connection role */ 761 } tBTA_DM_ROLE_CHG; 762 763 /* Structure associated with BTA_DM_BUSY_LEVEL_EVT */ 764 typedef struct 765 { 766 UINT8 level; /* when paging or inquiring, level is 10. 767 Otherwise, the number of ACL links */ 768 UINT8 level_flags; /* indicates individual flags */ 769 } tBTA_DM_BUSY_LEVEL; 770 771 #define BTA_IO_CAP_OUT BTM_IO_CAP_OUT /* 0 DisplayOnly */ 772 #define BTA_IO_CAP_IO BTM_IO_CAP_IO /* 1 DisplayYesNo */ 773 #define BTA_IO_CAP_IN BTM_IO_CAP_IN /* 2 KeyboardOnly */ 774 #define BTA_IO_CAP_NONE BTM_IO_CAP_NONE /* 3 NoInputNoOutput */ 775 #if BLE_INCLUDED == TRUE && SMP_INCLUDED == TRUE 776 #define BTA_IO_CAP_KBDISP BTM_IO_CAP_KBDISP /* 4 Keyboard display */ 777 #endif 778 typedef tBTM_IO_CAP tBTA_IO_CAP; 779 780 #define BTA_AUTH_SP_NO BTM_AUTH_SP_NO /* 0 MITM Protection Not Required - Single Profile/non-bonding 781 Numeric comparison with automatic accept allowed */ 782 #define BTA_AUTH_SP_YES BTM_AUTH_SP_YES /* 1 MITM Protection Required - Single Profile/non-bonding 783 Use IO Capabilities to determine authentication procedure */ 784 #define BTA_AUTH_AP_NO BTM_AUTH_AP_NO /* 2 MITM Protection Not Required - All Profiles/dedicated bonding 785 Numeric comparison with automatic accept allowed */ 786 #define BTA_AUTH_AP_YES BTM_AUTH_AP_YES /* 3 MITM Protection Required - All Profiles/dedicated bonding 787 Use IO Capabilities to determine authentication procedure */ 788 #define BTA_AUTH_SPGB_NO BTM_AUTH_SPGB_NO /* 4 MITM Protection Not Required - Single Profiles/general bonding 789 Numeric comparison with automatic accept allowed */ 790 #define BTA_AUTH_SPGB_YES BTM_AUTH_SPGB_YES /* 5 MITM Protection Required - Single Profiles/general bonding 791 Use IO Capabilities to determine authentication procedure */ 792 typedef tBTM_AUTH_REQ tBTA_AUTH_REQ; 793 794 #define BTA_AUTH_DD_BOND BTM_AUTH_DD_BOND /* 2 this bit is set for dedicated bonding */ 795 #define BTA_AUTH_GEN_BOND BTM_AUTH_SPGB_NO /* 4 this bit is set for general bonding */ 796 #define BTA_AUTH_BONDS BTM_AUTH_BONDS /* 6 the general/dedicated bonding bits */ 797 798 #define BTA_LE_AUTH_NO_BOND BTM_LE_AUTH_REQ_NO_BOND /* 0*/ 799 #define BTA_LE_AUTH_BOND BTM_LE_AUTH_REQ_BOND /* 1 << 0 */ 800 #define BTA_LE_AUTH_REQ_MITM BTM_LE_AUTH_REQ_MITM /* 1 << 2 */ 801 802 #define BTA_LE_AUTH_REQ_SC_ONLY BTM_LE_AUTH_REQ_SC_ONLY /* 1 << 3 */ 803 #define BTA_LE_AUTH_REQ_SC_BOND BTM_LE_AUTH_REQ_SC_BOND /* 1001 */ 804 #define BTA_LE_AUTH_REQ_SC_MITM BTM_LE_AUTH_REQ_SC_MITM /* 1100 */ 805 #define BTA_LE_AUTH_REQ_SC_MITM_BOND BTM_LE_AUTH_REQ_SC_MITM_BOND /* 1101 */ 806 typedef tBTM_LE_AUTH_REQ tBTA_LE_AUTH_REQ; /* combination of the above bit pattern */ 807 808 #define BTA_OOB_NONE BTM_OOB_NONE 809 #define BTA_OOB_PRESENT BTM_OOB_PRESENT 810 #define BTA_OOB_UNKNOWN BTM_OOB_UNKNOWN 811 812 typedef tBTM_OOB_DATA tBTA_OOB_DATA; 813 814 /* Structure associated with BTA_DM_SP_CFM_REQ_EVT */ 815 typedef struct 816 { 817 /* Note: First 3 data members must be, bd_addr, dev_class, and bd_name in order */ 818 BD_ADDR bd_addr; /* peer address */ 819 DEV_CLASS dev_class; /* peer CoD */ 820 BD_NAME bd_name; /* peer device name */ 821 UINT32 num_val; /* the numeric value for comparison. If just_works, do not show this number to UI */ 822 BOOLEAN just_works; /* TRUE, if "Just Works" association model */ 823 tBTA_AUTH_REQ loc_auth_req; /* Authentication required for local device */ 824 tBTA_AUTH_REQ rmt_auth_req; /* Authentication required for peer device */ 825 tBTA_IO_CAP loc_io_caps; /* IO Capabilities of local device */ 826 tBTA_AUTH_REQ rmt_io_caps; /* IO Capabilities of remote device */ 827 } tBTA_DM_SP_CFM_REQ; 828 829 enum 830 { 831 BTA_SP_KEY_STARTED, /* passkey entry started */ 832 BTA_SP_KEY_ENTERED, /* passkey digit entered */ 833 BTA_SP_KEY_ERASED, /* passkey digit erased */ 834 BTA_SP_KEY_CLEARED, /* passkey cleared */ 835 BTA_SP_KEY_COMPLT /* passkey entry completed */ 836 }; 837 typedef UINT8 tBTA_SP_KEY_TYPE; 838 839 /* Structure associated with BTA_DM_SP_KEYPRESS_EVT */ 840 typedef struct 841 { 842 BD_ADDR bd_addr; /* peer address */ 843 tBTA_SP_KEY_TYPE notif_type; 844 }tBTA_DM_SP_KEY_PRESS; 845 846 /* Structure associated with BTA_DM_SP_KEY_NOTIF_EVT */ 847 typedef struct 848 { 849 /* Note: First 3 data members must be, bd_addr, dev_class, and bd_name in order */ 850 BD_ADDR bd_addr; /* peer address */ 851 DEV_CLASS dev_class; /* peer CoD */ 852 BD_NAME bd_name; /* peer device name */ 853 UINT32 passkey; /* the numeric value for comparison. If just_works, do not show this number to UI */ 854 } tBTA_DM_SP_KEY_NOTIF; 855 856 /* Structure associated with BTA_DM_SP_RMT_OOB_EVT */ 857 typedef struct 858 { 859 /* Note: First 3 data members must be, bd_addr, dev_class, and bd_name in order */ 860 BD_ADDR bd_addr; /* peer address */ 861 DEV_CLASS dev_class; /* peer CoD */ 862 BD_NAME bd_name; /* peer device name */ 863 } tBTA_DM_SP_RMT_OOB; 864 865 /* Structure associated with BTA_DM_BOND_CANCEL_CMPL_EVT */ 866 typedef struct 867 { 868 tBTA_STATUS result; /* TRUE of bond cancel succeeded, FALSE if failed. */ 869 } tBTA_DM_BOND_CANCEL_CMPL; 870 871 /* Union of all security callback structures */ 872 typedef union 873 { 874 tBTA_DM_ENABLE enable; /* BTA enabled */ 875 tBTA_DM_PIN_REQ pin_req; /* PIN request. */ 876 tBTA_DM_AUTH_CMPL auth_cmpl; /* Authentication complete indication. */ 877 tBTA_DM_AUTHORIZE authorize; /* Authorization request. */ 878 tBTA_DM_LINK_UP link_up; /* ACL connection down event */ 879 tBTA_DM_LINK_DOWN link_down; /* ACL connection down event */ 880 tBTA_DM_BUSY_LEVEL busy_level; /* System busy level */ 881 tBTA_DM_SP_CFM_REQ cfm_req; /* user confirm request */ 882 tBTA_DM_SP_KEY_NOTIF key_notif; /* passkey notification */ 883 tBTA_DM_SP_RMT_OOB rmt_oob; /* remote oob */ 884 tBTA_DM_BOND_CANCEL_CMPL bond_cancel_cmpl; /* Bond Cancel Complete indication */ 885 tBTA_DM_SP_KEY_PRESS key_press; /* key press notification event */ 886 tBTA_DM_ROLE_CHG role_chg; /* role change event */ 887 tBTA_DM_BLE_SEC_REQ ble_req; /* BLE SMP related request */ 888 tBTA_DM_BLE_KEY ble_key; /* BLE SMP keys used when pairing */ 889 tBTA_BLE_LOCAL_ID_KEYS ble_id_keys; /* IR event */ 890 BT_OCTET16 ble_er; /* ER event data */ 891 } tBTA_DM_SEC; 892 893 /* Security callback */ 894 typedef void (tBTA_DM_SEC_CBACK)(tBTA_DM_SEC_EVT event, tBTA_DM_SEC *p_data); 895 896 #define BTA_BLE_MULTI_ADV_ILLEGAL 0 897 898 /* multi adv callback event */ 899 #define BTA_BLE_MULTI_ADV_ENB_EVT 1 900 #define BTA_BLE_MULTI_ADV_DISABLE_EVT 2 901 #define BTA_BLE_MULTI_ADV_PARAM_EVT 3 902 #define BTA_BLE_MULTI_ADV_DATA_EVT 4 903 904 typedef UINT8 tBTA_BLE_MULTI_ADV_EVT; 905 906 /* multi adv callback */ 907 typedef void (tBTA_BLE_MULTI_ADV_CBACK)(tBTA_BLE_MULTI_ADV_EVT event, 908 UINT8 inst_id, void *p_ref, tBTA_STATUS status); 909 typedef UINT32 tBTA_DM_BLE_REF_VALUE; 910 911 #define BTA_DM_BLE_PF_ENABLE_EVT BTM_BLE_PF_ENABLE 912 #define BTA_DM_BLE_PF_CONFIG_EVT BTM_BLE_PF_CONFIG 913 typedef UINT8 tBTA_DM_BLE_PF_EVT; 914 915 #define BTA_DM_BLE_PF_ENABLE 1 916 #define BTA_DM_BLE_PF_CONFIG 2 917 typedef UINT8 tBTA_DM_BLE_PF_ACTION; 918 919 /* Config callback */ 920 typedef void (tBTA_DM_BLE_PF_CFG_CBACK) (tBTA_DM_BLE_PF_ACTION action, 921 tBTA_DM_BLE_PF_COND_TYPE cfg_cond, 922 tBTA_DM_BLE_PF_AVBL_SPACE avbl_space, tBTA_STATUS status, 923 tBTA_DM_BLE_REF_VALUE ref_value); 924 /* Param callback */ 925 typedef void (tBTA_DM_BLE_PF_PARAM_CBACK) (UINT8 action_type, tBTA_DM_BLE_PF_AVBL_SPACE avbl_space, 926 tBTA_DM_BLE_REF_VALUE ref_value, tBTA_STATUS status); 927 928 /* Status callback */ 929 typedef void (tBTA_DM_BLE_PF_STATUS_CBACK) (UINT8 action, tBTA_STATUS status, 930 tBTA_DM_BLE_REF_VALUE ref_value); 931 932 933 #define BTA_DM_BLE_PF_BRDCAST_ADDR_FILT 1 934 #define BTA_DM_BLE_PF_SERV_DATA_CHG_FILT 2 935 #define BTA_DM_BLE_PF_SERV_UUID 4 936 #define BTA_DM_BLE_PF_SERV_SOLC_UUID 8 937 #define BTA_DM_BLE_PF_LOC_NAME_CHECK 16 938 #define BTA_DM_BLE_PF_MANUF_NAME_CHECK 32 939 #define BTA_DM_BLE_PF_SERV_DATA_CHECK 64 940 typedef UINT16 tBTA_DM_BLE_PF_FEAT_SEL; 941 942 #define BTA_DM_BLE_PF_LIST_LOGIC_OR 1 943 #define BTA_DM_BLE_PF_LIST_LOGIC_AND 2 944 typedef UINT16 tBTA_DM_BLE_PF_LIST_LOGIC_TYPE; 945 946 #define BTA_DM_BLE_PF_FILT_LOGIC_OR 0 947 #define BTA_DM_BLE_PF_FILT_LOGIC_AND 1 948 typedef UINT16 tBTA_DM_BLE_PF_FILT_LOGIC_TYPE; 949 950 typedef UINT8 tBTA_DM_BLE_PF_RSSI_THRESHOLD; 951 typedef UINT8 tBTA_DM_BLE_PF_DELIVERY_MODE; 952 typedef UINT16 tBTA_DM_BLE_PF_TIMEOUT; 953 typedef UINT8 tBTA_DM_BLE_PF_TIMEOUT_CNT; 954 typedef UINT16 tBTA_DM_BLE_PF_ADV_TRACK_ENTRIES; 955 956 typedef struct 957 { 958 tBTA_DM_BLE_PF_FEAT_SEL feat_seln; 959 tBTA_DM_BLE_PF_LIST_LOGIC_TYPE list_logic_type; 960 tBTA_DM_BLE_PF_FILT_LOGIC_TYPE filt_logic_type; 961 tBTA_DM_BLE_PF_RSSI_THRESHOLD rssi_high_thres; 962 tBTA_DM_BLE_PF_RSSI_THRESHOLD rssi_low_thres; 963 tBTA_DM_BLE_PF_DELIVERY_MODE dely_mode; 964 tBTA_DM_BLE_PF_TIMEOUT found_timeout; 965 tBTA_DM_BLE_PF_TIMEOUT lost_timeout; 966 tBTA_DM_BLE_PF_TIMEOUT_CNT found_timeout_cnt; 967 tBTA_DM_BLE_PF_ADV_TRACK_ENTRIES num_of_tracking_entries; 968 } tBTA_DM_BLE_PF_FILT_PARAMS; 969 970 /* Search callback events */ 971 #define BTA_DM_INQ_RES_EVT 0 /* Inquiry result for a peer device. */ 972 #define BTA_DM_INQ_CMPL_EVT 1 /* Inquiry complete. */ 973 #define BTA_DM_DISC_RES_EVT 2 /* Discovery result for a peer device. */ 974 #define BTA_DM_DISC_BLE_RES_EVT 3 /* Discovery result for BLE GATT based servoce on a peer device. */ 975 #define BTA_DM_DISC_CMPL_EVT 4 /* Discovery complete. */ 976 #define BTA_DM_DI_DISC_CMPL_EVT 5 /* Discovery complete. */ 977 #define BTA_DM_SEARCH_CANCEL_CMPL_EVT 6 /* Search cancelled */ 978 979 typedef UINT8 tBTA_DM_SEARCH_EVT; 980 981 #define BTA_DM_INQ_RES_IGNORE_RSSI BTM_INQ_RES_IGNORE_RSSI /* 0x7f RSSI value not supplied (ignore it) */ 982 983 /* Structure associated with BTA_DM_INQ_RES_EVT */ 984 typedef struct 985 { 986 BD_ADDR bd_addr; /* BD address peer device. */ 987 DEV_CLASS dev_class; /* Device class of peer device. */ 988 BOOLEAN remt_name_not_required; /* Application sets this flag if it already knows the name of the device */ 989 /* If the device name is known to application BTA skips the remote name request */ 990 BOOLEAN is_limited; /* TRUE, if the limited inquiry bit is set in the CoD */ 991 INT8 rssi; /* The rssi value */ 992 UINT8 *p_eir; /* received EIR */ 993 #if (BLE_INCLUDED == TRUE) 994 UINT8 inq_result_type; 995 UINT8 ble_addr_type; 996 tBTM_BLE_EVT_TYPE ble_evt_type; 997 tBT_DEVICE_TYPE device_type; 998 UINT8 flag; 999 #endif 1000 1001 } tBTA_DM_INQ_RES; 1002 1003 /* Structure associated with BTA_DM_INQ_CMPL_EVT */ 1004 typedef struct 1005 { 1006 UINT8 num_resps; /* Number of inquiry responses. */ 1007 } tBTA_DM_INQ_CMPL; 1008 1009 /* Structure associated with BTA_DM_DI_DISC_CMPL_EVT */ 1010 typedef struct 1011 { 1012 BD_ADDR bd_addr; /* BD address peer device. */ 1013 UINT8 num_record; /* Number of DI record */ 1014 tBTA_STATUS result; 1015 } tBTA_DM_DI_DISC_CMPL; 1016 1017 /* Structure associated with BTA_DM_DISC_RES_EVT */ 1018 typedef struct 1019 { 1020 BD_ADDR bd_addr; /* BD address peer device. */ 1021 BD_NAME bd_name; /* Name of peer device. */ 1022 tBTA_SERVICE_MASK services; /* Services found on peer device. */ 1023 UINT8 * p_raw_data; /* Raw data for discovery DB */ 1024 UINT32 raw_data_size; /* size of raw data */ 1025 tBT_DEVICE_TYPE device_type; /* device type in case it is BLE device */ 1026 UINT32 num_uuids; 1027 UINT8 *p_uuid_list; 1028 tBTA_STATUS result; 1029 } tBTA_DM_DISC_RES; 1030 1031 /* Structure associated with tBTA_DM_DISC_BLE_RES */ 1032 typedef struct 1033 { 1034 BD_ADDR bd_addr; /* BD address peer device. */ 1035 BD_NAME bd_name; /* Name of peer device. */ 1036 tBT_UUID service; /* GATT based Services UUID found on peer device. */ 1037 } tBTA_DM_DISC_BLE_RES; 1038 1039 1040 /* Union of all search callback structures */ 1041 typedef union 1042 { 1043 tBTA_DM_INQ_RES inq_res; /* Inquiry result for a peer device. */ 1044 tBTA_DM_INQ_CMPL inq_cmpl; /* Inquiry complete. */ 1045 tBTA_DM_DISC_RES disc_res; /* Discovery result for a peer device. */ 1046 tBTA_DM_DISC_BLE_RES disc_ble_res; /* discovery result for GATT based service */ 1047 tBTA_DM_DI_DISC_CMPL di_disc; /* DI discovery result for a peer device */ 1048 1049 } tBTA_DM_SEARCH; 1050 1051 /* Search callback */ 1052 typedef void (tBTA_DM_SEARCH_CBACK)(tBTA_DM_SEARCH_EVT event, tBTA_DM_SEARCH *p_data); 1053 1054 /* Execute call back */ 1055 typedef void (tBTA_DM_EXEC_CBACK) (void * p_param); 1056 1057 /* Encryption callback*/ 1058 typedef void (tBTA_DM_ENCRYPT_CBACK) (BD_ADDR bd_addr, tBTA_TRANSPORT transport, tBTA_STATUS result); 1059 1060 #define BTA_DM_BLE_SEC_NONE BTM_BLE_SEC_NONE 1061 #define BTA_DM_BLE_SEC_ENCRYPT BTM_BLE_SEC_ENCRYPT 1062 #define BTA_DM_BLE_SEC_NO_MITM BTM_BLE_SEC_ENCRYPT_NO_MITM 1063 #define BTA_DM_BLE_SEC_MITM BTM_BLE_SEC_ENCRYPT_MITM 1064 typedef tBTM_BLE_SEC_ACT tBTA_DM_BLE_SEC_ACT; 1065 1066 #if BLE_INCLUDED == TRUE 1067 typedef tBTM_BLE_TX_TIME_MS tBTA_DM_BLE_TX_TIME_MS; 1068 typedef tBTM_BLE_RX_TIME_MS tBTA_DM_BLE_RX_TIME_MS; 1069 typedef tBTM_BLE_IDLE_TIME_MS tBTA_DM_BLE_IDLE_TIME_MS; 1070 typedef tBTM_BLE_ENERGY_USED tBTA_DM_BLE_ENERGY_USED; 1071 1072 #define BTA_DM_CONTRL_UNKNOWN 0 /* Unknown state */ 1073 #define BTA_DM_CONTRL_ACTIVE 1 /* ACL link on, SCO link ongoing, sniff mode */ 1074 #define BTA_DM_CONTRL_SCAN 2 /* Scan state - paging/inquiry/trying to connect*/ 1075 #define BTA_DM_CONTRL_IDLE 3 /* Idle state - page scan, LE advt, inquiry scan */ 1076 1077 typedef UINT8 tBTA_DM_CONTRL_STATE; 1078 1079 typedef UINT8 tBTA_DM_BLE_ADV_STATE; 1080 typedef UINT8 tBTA_DM_BLE_ADV_INFO_PRESENT; 1081 typedef UINT8 tBTA_DM_BLE_RSSI_VALUE; 1082 typedef UINT16 tBTA_DM_BLE_ADV_INFO_TIMESTAMP; 1083 1084 typedef tBTM_BLE_TRACK_ADV_DATA tBTA_DM_BLE_TRACK_ADV_DATA; 1085 1086 typedef void (tBTA_BLE_SCAN_THRESHOLD_CBACK)(tBTA_DM_BLE_REF_VALUE ref_value); 1087 1088 typedef void (tBTA_BLE_SCAN_REP_CBACK) (tBTA_DM_BLE_REF_VALUE ref_value, UINT8 report_format, 1089 UINT8 num_records, UINT16 data_len, 1090 UINT8* p_rep_data, tBTA_STATUS status); 1091 1092 typedef void (tBTA_BLE_SCAN_SETUP_CBACK) (tBTA_BLE_BATCH_SCAN_EVT evt, 1093 tBTA_DM_BLE_REF_VALUE ref_value, 1094 tBTA_STATUS status); 1095 1096 typedef void (tBTA_BLE_TRACK_ADV_CMPL_CBACK)(int action, tBTA_STATUS status, 1097 tBTA_DM_BLE_PF_AVBL_SPACE avbl_space, 1098 tBTA_DM_BLE_REF_VALUE ref_value); 1099 1100 typedef void (tBTA_BLE_TRACK_ADV_CBACK)(tBTA_DM_BLE_TRACK_ADV_DATA *p_adv_data); 1101 1102 typedef void (tBTA_BLE_ENERGY_INFO_CBACK)(tBTA_DM_BLE_TX_TIME_MS tx_time, 1103 tBTA_DM_BLE_RX_TIME_MS rx_time, 1104 tBTA_DM_BLE_IDLE_TIME_MS idle_time, 1105 tBTA_DM_BLE_ENERGY_USED energy_used, 1106 tBTA_DM_CONTRL_STATE ctrl_state, 1107 tBTA_STATUS status); 1108 1109 #else 1110 typedef UINT8 tBTA_DM_BLE_SEC_ACT; 1111 #endif 1112 1113 /* Maximum service name length */ 1114 #define BTA_SERVICE_NAME_LEN 35 1115 #define BTA_SERVICE_DESP_LEN BTA_SERVICE_NAME_LEN 1116 #define BTA_PROVIDER_NAME_LEN BTA_SERVICE_NAME_LEN 1117 1118 1119 /* link policy masks */ 1120 #define BTA_DM_LP_SWITCH HCI_ENABLE_MASTER_SLAVE_SWITCH 1121 #define BTA_DM_LP_HOLD HCI_ENABLE_HOLD_MODE 1122 #define BTA_DM_LP_SNIFF HCI_ENABLE_SNIFF_MODE 1123 #define BTA_DM_LP_PARK HCI_ENABLE_PARK_MODE 1124 typedef UINT16 tBTA_DM_LP_MASK; 1125 1126 /* power mode actions */ 1127 #define BTA_DM_PM_NO_ACTION 0x00 /* no change to the current pm setting */ 1128 #define BTA_DM_PM_PARK 0x10 /* prefers park mode */ 1129 #define BTA_DM_PM_SNIFF 0x20 /* prefers sniff mode */ 1130 #define BTA_DM_PM_SNIFF1 0x21 /* prefers sniff1 mode */ 1131 #define BTA_DM_PM_SNIFF2 0x22 /* prefers sniff2 mode */ 1132 #define BTA_DM_PM_SNIFF3 0x23 /* prefers sniff3 mode */ 1133 #define BTA_DM_PM_SNIFF4 0x24 /* prefers sniff4 mode */ 1134 #define BTA_DM_PM_SNIFF5 0x25 /* prefers sniff5 mode */ 1135 #define BTA_DM_PM_SNIFF6 0x26 /* prefers sniff6 mode */ 1136 #define BTA_DM_PM_SNIFF7 0x27 /* prefers sniff7 mode */ 1137 #define BTA_DM_PM_SNIFF_USER0 0x28 /* prefers user-defined sniff0 mode (testtool only) */ 1138 #define BTA_DM_PM_SNIFF_USER1 0x29 /* prefers user-defined sniff1 mode (testtool only) */ 1139 #define BTA_DM_PM_ACTIVE 0x40 /* prefers active mode */ 1140 #define BTA_DM_PM_RETRY 0x80 /* retry power mode based on current settings */ 1141 #define BTA_DM_PM_SUSPEND 0x04 /* prefers suspend mode */ 1142 #define BTA_DM_PM_NO_PREF 0x01 /* service has no prefernce on power mode setting. eg. connection to service got closed */ 1143 1144 typedef UINT8 tBTA_DM_PM_ACTION; 1145 1146 /* index to bta_dm_ssr_spec */ 1147 #define BTA_DM_PM_SSR0 0 1148 #define BTA_DM_PM_SSR1 1 /* BTA_DM_PM_SSR1 will be dedicated for 1149 HH SSR setting entry, no other profile can use it */ 1150 #define BTA_DM_PM_SSR2 2 1151 #define BTA_DM_PM_SSR3 3 1152 #define BTA_DM_PM_SSR4 4 1153 #define BTA_DM_PM_SSR5 5 1154 #define BTA_DM_PM_SSR6 6 1155 1156 #define BTA_DM_PM_NUM_EVTS 9 1157 1158 #ifndef BTA_DM_PM_PARK_IDX 1159 #define BTA_DM_PM_PARK_IDX 5 /* the actual index to bta_dm_pm_md[] for PARK mode */ 1160 #endif 1161 1162 #ifndef BTA_DM_PM_SNIFF_A2DP_IDX 1163 #define BTA_DM_PM_SNIFF_A2DP_IDX BTA_DM_PM_SNIFF 1164 #endif 1165 1166 #ifndef BTA_DM_PM_SNIFF_HD_IDLE_IDX 1167 #define BTA_DM_PM_SNIFF_HD_IDLE_IDX BTA_DM_PM_SNIFF2 1168 #endif 1169 1170 #ifndef BTA_DM_PM_SNIFF_SCO_OPEN_IDX 1171 #define BTA_DM_PM_SNIFF_SCO_OPEN_IDX BTA_DM_PM_SNIFF3 1172 #endif 1173 1174 #ifndef BTA_DM_PM_SNIFF_HD_ACTIVE_IDX 1175 #define BTA_DM_PM_SNIFF_HD_ACTIVE_IDX BTA_DM_PM_SNIFF4 1176 #endif 1177 1178 #ifndef BTA_DM_PM_SNIFF_HH_OPEN_IDX 1179 #define BTA_DM_PM_SNIFF_HH_OPEN_IDX BTA_DM_PM_SNIFF2 1180 #endif 1181 1182 #ifndef BTA_DM_PM_SNIFF_HH_ACTIVE_IDX 1183 #define BTA_DM_PM_SNIFF_HH_ACTIVE_IDX BTA_DM_PM_SNIFF2 1184 #endif 1185 1186 #ifndef BTA_DM_PM_SNIFF_HH_IDLE_IDX 1187 #define BTA_DM_PM_SNIFF_HH_IDLE_IDX BTA_DM_PM_SNIFF2 1188 #endif 1189 1190 1191 #ifndef BTA_DM_PM_HH_OPEN_DELAY 1192 #define BTA_DM_PM_HH_OPEN_DELAY 30000 1193 #endif 1194 1195 #ifndef BTA_DM_PM_HH_ACTIVE_DELAY 1196 #define BTA_DM_PM_HH_ACTIVE_DELAY 30000 1197 #endif 1198 1199 #ifndef BTA_DM_PM_HH_IDLE_DELAY 1200 #define BTA_DM_PM_HH_IDLE_DELAY 30000 1201 #endif 1202 1203 /* The Sniff Parameters defined below must be ordered from highest 1204 * latency (biggest interval) to lowest latency. If there is a conflict 1205 * among the connected services the setting with the lowest latency will 1206 * be selected. If a device should override a sniff parameter then it 1207 * must insure that order is maintained. 1208 */ 1209 #ifndef BTA_DM_PM_SNIFF_MAX 1210 #define BTA_DM_PM_SNIFF_MAX 800 1211 #define BTA_DM_PM_SNIFF_MIN 400 1212 #define BTA_DM_PM_SNIFF_ATTEMPT 4 1213 #define BTA_DM_PM_SNIFF_TIMEOUT 1 1214 #endif 1215 1216 #ifndef BTA_DM_PM_SNIFF1_MAX 1217 #define BTA_DM_PM_SNIFF1_MAX 400 1218 #define BTA_DM_PM_SNIFF1_MIN 200 1219 #define BTA_DM_PM_SNIFF1_ATTEMPT 4 1220 #define BTA_DM_PM_SNIFF1_TIMEOUT 1 1221 #endif 1222 1223 #ifndef BTA_DM_PM_SNIFF2_MAX 1224 #define BTA_DM_PM_SNIFF2_MAX 180 1225 #define BTA_DM_PM_SNIFF2_MIN 150 1226 #define BTA_DM_PM_SNIFF2_ATTEMPT 4 1227 #define BTA_DM_PM_SNIFF2_TIMEOUT 1 1228 #endif 1229 1230 #ifndef BTA_DM_PM_SNIFF3_MAX 1231 #define BTA_DM_PM_SNIFF3_MAX 150 1232 #define BTA_DM_PM_SNIFF3_MIN 50 1233 #define BTA_DM_PM_SNIFF3_ATTEMPT 4 1234 #define BTA_DM_PM_SNIFF3_TIMEOUT 1 1235 #endif 1236 1237 #ifndef BTA_DM_PM_SNIFF4_MAX 1238 #define BTA_DM_PM_SNIFF4_MAX 54 1239 #define BTA_DM_PM_SNIFF4_MIN 30 1240 #define BTA_DM_PM_SNIFF4_ATTEMPT 4 1241 #define BTA_DM_PM_SNIFF4_TIMEOUT 1 1242 #endif 1243 1244 #ifndef BTA_DM_PM_SNIFF5_MAX 1245 #define BTA_DM_PM_SNIFF5_MAX 36 1246 #define BTA_DM_PM_SNIFF5_MIN 30 1247 #define BTA_DM_PM_SNIFF5_ATTEMPT 2 1248 #define BTA_DM_PM_SNIFF5_TIMEOUT 0 1249 #endif 1250 1251 #ifndef BTA_DM_PM_PARK_MAX 1252 #define BTA_DM_PM_PARK_MAX 800 1253 #define BTA_DM_PM_PARK_MIN 400 1254 #define BTA_DM_PM_PARK_ATTEMPT 0 1255 #define BTA_DM_PM_PARK_TIMEOUT 0 1256 #endif 1257 1258 1259 /* Switch callback events */ 1260 #define BTA_DM_SWITCH_CMPL_EVT 0 /* Completion of the Switch API */ 1261 1262 typedef UINT8 tBTA_DM_SWITCH_EVT; 1263 typedef void (tBTA_DM_SWITCH_CBACK)(tBTA_DM_SWITCH_EVT event, tBTA_STATUS status); 1264 1265 /* Audio routing out configuration */ 1266 #define BTA_DM_ROUTE_NONE 0x00 /* No Audio output */ 1267 #define BTA_DM_ROUTE_DAC 0x01 /* routing over analog output */ 1268 #define BTA_DM_ROUTE_I2S 0x02 /* routing over digital (I2S) output */ 1269 #define BTA_DM_ROUTE_BT_MONO 0x04 /* routing over SCO */ 1270 #define BTA_DM_ROUTE_BT_STEREO 0x08 /* routing over BT Stereo */ 1271 #define BTA_DM_ROUTE_HOST 0x10 /* routing over Host */ 1272 #define BTA_DM_ROUTE_FMTX 0x20 /* routing over FMTX */ 1273 #define BTA_DM_ROUTE_FMRX 0x40 /* routing over FMRX */ 1274 #define BTA_DM_ROUTE_BTSNK 0x80 /* routing over BT SNK */ 1275 1276 typedef UINT8 tBTA_DM_ROUTE_PATH; 1277 1278 1279 /* Device Identification (DI) data structure 1280 */ 1281 /* Used to set the DI record */ 1282 typedef tSDP_DI_RECORD tBTA_DI_RECORD; 1283 /* Used to get the DI record */ 1284 typedef tSDP_DI_GET_RECORD tBTA_DI_GET_RECORD; 1285 /* SDP discovery database */ 1286 typedef tSDP_DISCOVERY_DB tBTA_DISCOVERY_DB; 1287 1288 #ifndef BTA_DI_NUM_MAX 1289 #define BTA_DI_NUM_MAX 3 1290 #endif 1291 1292 /* Device features mask definitions */ 1293 #define BTA_FEATURE_BYTES_PER_PAGE BTM_FEATURE_BYTES_PER_PAGE 1294 #define BTA_EXT_FEATURES_PAGE_MAX BTM_EXT_FEATURES_PAGE_MAX 1295 /* ACL type 1296 */ 1297 #define BTA_DM_LINK_TYPE_BR_EDR 0x01 1298 #define BTA_DM_LINK_TYPE_LE 0x02 1299 #define BTA_DM_LINK_TYPE_ALL 0xFF 1300 typedef UINT8 tBTA_DM_LINK_TYPE; 1301 1302 #define IMMEDIATE_DELY_MODE 0x00 1303 #define ONFOUND_DELY_MODE 0x01 1304 #define BATCH_DELY_MODE 0x02 1305 #define ALLOW_ALL_FILTER 0x00 1306 #define LOWEST_RSSI_VALUE 129 1307 1308 /***************************************************************************** 1309 ** External Function Declarations 1310 *****************************************************************************/ 1311 #ifdef __cplusplus 1312 extern "C" 1313 { 1314 #endif 1315 1316 /******************************************************************************* 1317 ** 1318 ** Function BTA_EnableBluetooth 1319 ** 1320 ** Description This function initializes BTA and prepares BTA and the 1321 ** Bluetooth protocol stack for use. This function is 1322 ** typically called at startup or when Bluetooth services 1323 ** are required by the phone. This function must be called 1324 ** before calling any other API function. 1325 ** 1326 ** 1327 ** Returns BTA_SUCCESS if successful. 1328 ** BTA_FAIL if internal failure. 1329 ** 1330 *******************************************************************************/ 1331 extern tBTA_STATUS BTA_EnableBluetooth(tBTA_DM_SEC_CBACK *p_cback); 1332 1333 /******************************************************************************* 1334 ** 1335 ** Function BTA_DisableBluetooth 1336 ** 1337 ** Description This function disables BTA and the Bluetooth protocol 1338 ** stack. It is called when BTA is no longer being used 1339 ** by any application in the system. 1340 ** 1341 ** 1342 ** Returns void 1343 ** 1344 *******************************************************************************/ 1345 extern tBTA_STATUS BTA_DisableBluetooth(void); 1346 1347 /******************************************************************************* 1348 ** 1349 ** Function BTA_EnableTestMode 1350 ** 1351 ** Description Enables bluetooth device under test mode 1352 ** 1353 ** 1354 ** Returns tBTA_STATUS 1355 ** 1356 *******************************************************************************/ 1357 extern tBTA_STATUS BTA_EnableTestMode(void); 1358 1359 /******************************************************************************* 1360 ** 1361 ** Function BTA_DisableTestMode 1362 ** 1363 ** Description Disable bluetooth device under test mode 1364 ** 1365 ** 1366 ** Returns None 1367 ** 1368 *******************************************************************************/ 1369 extern void BTA_DisableTestMode(void); 1370 1371 /******************************************************************************* 1372 ** 1373 ** Function BTA_DmSetDeviceName 1374 ** 1375 ** Description This function sets the Bluetooth name of the local device. 1376 ** 1377 ** 1378 ** Returns void 1379 ** 1380 *******************************************************************************/ 1381 extern void BTA_DmSetDeviceName(char *p_name); 1382 1383 /******************************************************************************* 1384 ** 1385 ** Function BTA_DmSetVisibility 1386 ** 1387 ** Description This function sets the Bluetooth connectable,discoverable, 1388 ** pairable and conn paired only modesmodes of the local device. 1389 ** This controls whether other Bluetooth devices can find and connect to 1390 ** the local device. 1391 ** 1392 ** 1393 ** Returns void 1394 ** 1395 *******************************************************************************/ 1396 extern void BTA_DmSetVisibility(tBTA_DM_DISC disc_mode, tBTA_DM_CONN conn_mode, UINT8 pairable_mode, UINT8 conn_filter); 1397 1398 /******************************************************************************* 1399 ** 1400 ** Function BTA_DmSearch 1401 ** 1402 ** Description This function searches for peer Bluetooth devices. It 1403 ** first performs an inquiry; for each device found from the 1404 ** inquiry it gets the remote name of the device. If 1405 ** parameter services is nonzero, service discovery will be 1406 ** performed on each device for the services specified. 1407 ** 1408 ** 1409 ** Returns void 1410 ** 1411 *******************************************************************************/ 1412 extern void BTA_DmSearch(tBTA_DM_INQ *p_dm_inq, tBTA_SERVICE_MASK services, 1413 tBTA_DM_SEARCH_CBACK *p_cback); 1414 1415 /******************************************************************************* 1416 ** 1417 ** Function BTA_DmSearchCancel 1418 ** 1419 ** Description This function cancels a search that has been initiated 1420 ** by calling BTA_DmSearch(). 1421 ** 1422 ** 1423 ** Returns void 1424 ** 1425 *******************************************************************************/ 1426 extern void BTA_DmSearchCancel(void); 1427 1428 /******************************************************************************* 1429 ** 1430 ** Function BTA_DmDiscover 1431 ** 1432 ** Description This function performs service discovery for the services 1433 ** of a particular peer device. 1434 ** 1435 ** 1436 ** Returns void 1437 ** 1438 *******************************************************************************/ 1439 extern void BTA_DmDiscover(BD_ADDR bd_addr, tBTA_SERVICE_MASK services, 1440 tBTA_DM_SEARCH_CBACK *p_cback, BOOLEAN sdp_search); 1441 1442 /******************************************************************************* 1443 ** 1444 ** Function BTA_DmDiscoverUUID 1445 ** 1446 ** Description This function performs service discovery for the services 1447 ** of a particular peer device. 1448 ** 1449 ** 1450 ** Returns void 1451 ** 1452 *******************************************************************************/ 1453 extern void BTA_DmDiscoverUUID(BD_ADDR bd_addr, tSDP_UUID *uuid, 1454 tBTA_DM_SEARCH_CBACK *p_cback, BOOLEAN sdp_search); 1455 1456 /******************************************************************************* 1457 ** 1458 ** Function BTA_DmGetCachedRemoteName 1459 ** 1460 ** Description Retieve cached remote name if available 1461 ** 1462 ** Returns BTA_SUCCESS if cached name was retrieved 1463 ** BTA_FAILURE if cached name is not available 1464 ** 1465 *******************************************************************************/ 1466 tBTA_STATUS BTA_DmGetCachedRemoteName(BD_ADDR remote_device, UINT8 **pp_cached_name); 1467 1468 /******************************************************************************* 1469 ** 1470 ** Function BTA_DmBond 1471 ** 1472 ** Description This function initiates a bonding procedure with a peer 1473 ** device. The bonding procedure enables authentication 1474 ** and optionally encryption on the Bluetooth link. 1475 ** 1476 ** 1477 ** Returns void 1478 ** 1479 *******************************************************************************/ 1480 extern void BTA_DmBond(BD_ADDR bd_addr); 1481 1482 /******************************************************************************* 1483 ** 1484 ** Function BTA_DmBondByTransport 1485 ** 1486 ** Description This function initiates a bonding procedure with a peer 1487 ** device by designated transport. The bonding procedure enables 1488 ** authentication and optionally encryption on the Bluetooth link. 1489 ** 1490 ** 1491 ** Returns void 1492 ** 1493 *******************************************************************************/ 1494 extern void BTA_DmBondByTransport(BD_ADDR bd_addr, tBTA_TRANSPORT transport); 1495 1496 1497 /******************************************************************************* 1498 ** 1499 ** Function BTA_DmBondCancel 1500 ** 1501 ** Description This function cancels a bonding procedure with a peer 1502 ** device. 1503 ** 1504 ** 1505 ** Returns void 1506 ** 1507 *******************************************************************************/ 1508 extern void BTA_DmBondCancel(BD_ADDR bd_addr); 1509 1510 /******************************************************************************* 1511 ** 1512 ** Function BTA_DmPinReply 1513 ** 1514 ** Description This function provides a PIN when one is requested by DM 1515 ** during a bonding procedure. The application should call 1516 ** this function after the security callback is called with 1517 ** a BTA_DM_PIN_REQ_EVT. 1518 ** 1519 ** 1520 ** Returns void 1521 ** 1522 *******************************************************************************/ 1523 extern void BTA_DmPinReply(BD_ADDR bd_addr, BOOLEAN accept, UINT8 pin_len, 1524 UINT8 *p_pin); 1525 1526 /******************************************************************************* 1527 ** 1528 ** Function BTA_DmLocalOob 1529 ** 1530 ** Description This function retrieves the OOB data from local controller. 1531 ** The result is reported by bta_dm_co_loc_oob(). 1532 ** 1533 ** Returns void 1534 ** 1535 *******************************************************************************/ 1536 extern void BTA_DmLocalOob(void); 1537 1538 /******************************************************************************* 1539 ** 1540 ** Function BTA_DmConfirm 1541 ** 1542 ** Description This function accepts or rejects the numerical value of the 1543 ** Simple Pairing process on BTA_DM_SP_CFM_REQ_EVT 1544 ** 1545 ** Returns void 1546 ** 1547 *******************************************************************************/ 1548 extern void BTA_DmConfirm(BD_ADDR bd_addr, BOOLEAN accept); 1549 1550 /******************************************************************************* 1551 ** 1552 ** Function BTA_DmAddDevice 1553 ** 1554 ** Description This function adds a device to the security database list 1555 ** of peer devices. This function would typically be called 1556 ** at system startup to initialize the security database with 1557 ** known peer devices. This is a direct execution function 1558 ** that may lock task scheduling on some platforms. 1559 ** 1560 ** Returns void 1561 ** 1562 *******************************************************************************/ 1563 extern void BTA_DmAddDevice(BD_ADDR bd_addr, DEV_CLASS dev_class, 1564 LINK_KEY link_key, tBTA_SERVICE_MASK trusted_mask, 1565 BOOLEAN is_trusted, UINT8 key_type, 1566 tBTA_IO_CAP io_cap, UINT8 pin_length); 1567 1568 /******************************************************************************* 1569 ** 1570 ** Function BTA_DmRemoveDevice 1571 ** 1572 ** Description This function removes a device from the security database. 1573 ** This is a direct execution function that may lock task 1574 ** scheduling on some platforms. 1575 ** 1576 ** 1577 ** Returns BTA_SUCCESS if successful. 1578 ** BTA_FAIL if operation failed. 1579 ** 1580 *******************************************************************************/ 1581 extern tBTA_STATUS BTA_DmRemoveDevice(BD_ADDR bd_addr); 1582 1583 /******************************************************************************* 1584 ** 1585 ** Function BTA_GetEirService 1586 ** 1587 ** Description This function is called to get BTA service mask from EIR. 1588 ** 1589 ** Parameters p_eir - pointer of EIR significant part 1590 ** p_services - return the BTA service mask 1591 ** 1592 ** Returns None 1593 ** 1594 *******************************************************************************/ 1595 extern void BTA_GetEirService( UINT8 *p_eir, tBTA_SERVICE_MASK *p_services ); 1596 1597 /******************************************************************************* 1598 ** 1599 ** Function BTA_DmGetConnectionState 1600 ** 1601 ** Description Returns whether the remote device is currently connected. 1602 ** 1603 ** Returns 0 if the device is NOT connected. 1604 ** 1605 *******************************************************************************/ 1606 extern UINT16 BTA_DmGetConnectionState( BD_ADDR bd_addr ); 1607 1608 1609 /******************************************************************************* 1610 ** 1611 ** Function BTA_DmSetLocalDiRecord 1612 ** 1613 ** Description This function adds a DI record to the local SDP database. 1614 ** 1615 ** Returns BTA_SUCCESS if record set sucessfully, otherwise error code. 1616 ** 1617 *******************************************************************************/ 1618 extern tBTA_STATUS BTA_DmSetLocalDiRecord( tBTA_DI_RECORD *p_device_info, 1619 UINT32 *p_handle ); 1620 1621 /******************************************************************************* 1622 ** 1623 ** 1624 ** Function BTA_DmCloseACL 1625 ** 1626 ** Description This function force to close an ACL connection and remove the 1627 ** device from the security database list of known devices. 1628 ** 1629 ** Parameters: bd_addr - Address of the peer device 1630 ** remove_dev - remove device or not after link down 1631 ** transport - which transport to close 1632 1633 ** 1634 ** Returns void. 1635 ** 1636 *******************************************************************************/ 1637 extern void BTA_DmCloseACL(BD_ADDR bd_addr, BOOLEAN remove_dev, tBTA_TRANSPORT transport); 1638 1639 /******************************************************************************* 1640 ** 1641 ** Function bta_dmexecutecallback 1642 ** 1643 ** Description This function will request BTA to execute a call back in the context of BTU task 1644 ** This API was named in lower case because it is only intended 1645 ** for the internal customers(like BTIF). 1646 ** 1647 ** Returns void 1648 ** 1649 *******************************************************************************/ 1650 extern void bta_dmexecutecallback (tBTA_DM_EXEC_CBACK* p_callback, void * p_param); 1651 1652 #if (BTM_SCO_HCI_INCLUDED == TRUE) 1653 /******************************************************************************* 1654 ** 1655 ** Function BTA_DmPcmInitSamples 1656 ** 1657 ** Description initialize the down sample converter. 1658 ** 1659 ** src_sps: original samples per second (source audio data) 1660 ** (ex. 44100, 48000) 1661 ** bits: number of bits per pcm sample (16) 1662 ** n_channels: number of channels (i.e. mono(1), stereo(2)...) 1663 ** 1664 ** Returns none 1665 ** 1666 *******************************************************************************/ 1667 extern void BTA_DmPcmInitSamples (UINT32 src_sps, UINT32 bits, UINT32 n_channels); 1668 1669 /************************************************************************************** 1670 ** Function BTA_DmPcmResample 1671 ** 1672 ** Description Down sampling utility to convert higher sampling rate into 8K/16bits 1673 ** PCM samples. 1674 ** 1675 ** Parameters p_src: pointer to the buffer where the original sampling PCM 1676 ** are stored. 1677 ** in_bytes: Length of the input PCM sample buffer in byte. 1678 ** p_dst: pointer to the buffer which is to be used to store 1679 ** the converted PCM samples. 1680 ** 1681 ** 1682 ** Returns INT32: number of samples converted. 1683 ** 1684 **************************************************************************************/ 1685 extern INT32 BTA_DmPcmResample (void *p_src, UINT32 in_bytes, void *p_dst); 1686 #endif 1687 1688 #if ((defined BLE_INCLUDED) && (BLE_INCLUDED == TRUE)) 1689 /* BLE related API functions */ 1690 /******************************************************************************* 1691 ** 1692 ** Function BTA_DmBleSecurityGrant 1693 ** 1694 ** Description Grant security request access. 1695 ** 1696 ** Parameters: bd_addr - BD address of the peer 1697 ** res - security grant status. 1698 ** 1699 ** Returns void 1700 ** 1701 *******************************************************************************/ 1702 extern void BTA_DmBleSecurityGrant(BD_ADDR bd_addr, tBTA_DM_BLE_SEC_GRANT res); 1703 1704 1705 1706 /******************************************************************************* 1707 ** 1708 ** Function BTA_DmBleSetBgConnType 1709 ** 1710 ** Description This function is called to set BLE connectable mode for a 1711 ** peripheral device. 1712 ** 1713 ** Parameters bg_conn_type: it can be auto connection, or selective connection. 1714 ** p_select_cback: callback function when selective connection procedure 1715 ** is being used. 1716 ** 1717 ** Returns void 1718 ** 1719 *******************************************************************************/ 1720 extern void BTA_DmBleSetBgConnType(tBTA_DM_BLE_CONN_TYPE bg_conn_type, tBTA_DM_BLE_SEL_CBACK *p_select_cback); 1721 1722 /******************************************************************************* 1723 ** 1724 ** Function BTA_DmBlePasskeyReply 1725 ** 1726 ** Description Send BLE SMP passkey reply. 1727 ** 1728 ** Parameters: bd_addr - BD address of the peer 1729 ** accept - passkey entry sucessful or declined. 1730 ** passkey - passkey value, must be a 6 digit number, 1731 ** can be lead by 0. 1732 ** 1733 ** Returns void 1734 ** 1735 *******************************************************************************/ 1736 extern void BTA_DmBlePasskeyReply(BD_ADDR bd_addr, BOOLEAN accept, UINT32 passkey); 1737 1738 /******************************************************************************* 1739 ** 1740 ** Function BTA_DmBleConfirmReply 1741 ** 1742 ** Description Send BLE SMP SC user confirmation reply. 1743 ** 1744 ** Parameters: bd_addr - BD address of the peer 1745 ** accept - numbers to compare are the same or different. 1746 ** 1747 ** Returns void 1748 ** 1749 *******************************************************************************/ 1750 extern void BTA_DmBleConfirmReply(BD_ADDR bd_addr, BOOLEAN accept); 1751 1752 /******************************************************************************* 1753 ** 1754 ** Function BTA_DmAddBleDevice 1755 ** 1756 ** Description Add a BLE device. This function will be normally called 1757 ** during host startup to restore all required information 1758 ** for a LE device stored in the NVRAM. 1759 ** 1760 ** Parameters: bd_addr - BD address of the peer 1761 ** dev_type - Remote device's device type. 1762 ** addr_type - LE device address type. 1763 ** 1764 ** Returns void 1765 ** 1766 *******************************************************************************/ 1767 extern void BTA_DmAddBleDevice(BD_ADDR bd_addr, tBLE_ADDR_TYPE addr_type, 1768 tBT_DEVICE_TYPE dev_type); 1769 1770 1771 /******************************************************************************* 1772 ** 1773 ** Function BTA_DmAddBleKey 1774 ** 1775 ** Description Add/modify LE device information. This function will be 1776 ** normally called during host startup to restore all required 1777 ** information stored in the NVRAM. 1778 ** 1779 ** Parameters: bd_addr - BD address of the peer 1780 ** p_le_key - LE key values. 1781 ** key_type - LE SMP key type. 1782 ** 1783 ** Returns void 1784 ** 1785 *******************************************************************************/ 1786 extern void BTA_DmAddBleKey (BD_ADDR bd_addr, 1787 tBTA_LE_KEY_VALUE *p_le_key, 1788 tBTA_LE_KEY_TYPE key_type); 1789 1790 /******************************************************************************* 1791 ** 1792 ** Function BTA_DmSetBlePrefConnParams 1793 ** 1794 ** Description This function is called to set the preferred connection 1795 ** parameters when default connection parameter is not desired. 1796 ** 1797 ** Parameters: bd_addr - BD address of the peripheral 1798 ** min_conn_int - minimum preferred connection interval 1799 ** max_conn_int - maximum preferred connection interval 1800 ** slave_latency - preferred slave latency 1801 ** supervision_tout - preferred supervision timeout 1802 ** 1803 ** 1804 ** Returns void 1805 ** 1806 *******************************************************************************/ 1807 extern void BTA_DmSetBlePrefConnParams(BD_ADDR bd_addr, 1808 UINT16 min_conn_int, UINT16 max_conn_int, 1809 UINT16 slave_latency, UINT16 supervision_tout ); 1810 1811 /******************************************************************************* 1812 ** 1813 ** Function BTA_DmSetBleConnScanParams 1814 ** 1815 ** Description This function is called to set scan parameters used in 1816 ** BLE connection request 1817 ** 1818 ** Parameters: scan_interval - scan interval 1819 ** scan_window - scan window 1820 ** 1821 ** Returns void 1822 ** 1823 *******************************************************************************/ 1824 extern void BTA_DmSetBleConnScanParams(UINT32 scan_interval, 1825 UINT32 scan_window); 1826 1827 /******************************************************************************* 1828 ** 1829 ** Function BTA_DmSetBleScanParams 1830 ** 1831 ** Description This function is called to set scan parameters 1832 ** 1833 ** Parameters: client_if - Client IF 1834 ** scan_interval - scan interval 1835 ** scan_window - scan window 1836 ** scan_mode - scan mode 1837 ** scan_param_setup_status_cback - Set scan param status callback 1838 ** 1839 ** Returns void 1840 ** 1841 *******************************************************************************/ 1842 extern void BTA_DmSetBleScanParams(tGATT_IF client_if, UINT32 scan_interval, 1843 UINT32 scan_window, tBLE_SCAN_MODE scan_mode, 1844 tBLE_SCAN_PARAM_SETUP_CBACK scan_param_setup_status_cback); 1845 1846 /******************************************************************************* 1847 ** 1848 ** Function BTA_DmSetBleAdvParams 1849 ** 1850 ** Description This function sets the advertising parameters BLE functionality. 1851 ** It is to be called when device act in peripheral or broadcaster 1852 ** role. 1853 ** 1854 ** Parameters: adv_int_min - adv interval minimum 1855 ** adv_int_max - adv interval max 1856 ** p_dir_bda - directed adv initator address 1857 ** 1858 ** Returns void 1859 ** 1860 *******************************************************************************/ 1861 extern void BTA_DmSetBleAdvParams (UINT16 adv_int_min, UINT16 adv_int_max, 1862 tBLE_BD_ADDR *p_dir_bda); 1863 /******************************************************************************* 1864 ** 1865 ** Function BTA_DmSearchExt 1866 ** 1867 ** Description This function searches for peer Bluetooth devices. It performs 1868 ** an inquiry and gets the remote name for devices. Service 1869 ** discovery is done if services is non zero 1870 ** 1871 ** Parameters p_dm_inq: inquiry conditions 1872 ** services: if service is not empty, service discovery will be done. 1873 ** for all GATT based service condition, put num_uuid, and 1874 ** p_uuid is the pointer to the list of UUID values. 1875 ** p_cback: callback functino when search is completed. 1876 ** 1877 ** 1878 ** 1879 ** Returns void 1880 ** 1881 *******************************************************************************/ 1882 extern void BTA_DmSearchExt(tBTA_DM_INQ *p_dm_inq, tBTA_SERVICE_MASK_EXT *p_services, 1883 tBTA_DM_SEARCH_CBACK *p_cback); 1884 1885 /******************************************************************************* 1886 ** 1887 ** Function BTA_DmDiscoverExt 1888 ** 1889 ** Description This function does service discovery for services of a 1890 ** peer device. When services.num_uuid is 0, it indicates all 1891 ** GATT based services are to be searched; other wise a list of 1892 ** UUID of interested services should be provided through 1893 ** services.p_uuid. 1894 ** 1895 ** 1896 ** 1897 ** Returns void 1898 ** 1899 *******************************************************************************/ 1900 extern void BTA_DmDiscoverExt(BD_ADDR bd_addr, tBTA_SERVICE_MASK_EXT *p_services, 1901 tBTA_DM_SEARCH_CBACK *p_cback, BOOLEAN sdp_search); 1902 1903 /******************************************************************************* 1904 ** 1905 ** Function BTA_DmDiscoverByTransport 1906 ** 1907 ** Description This function does service discovery on particular transport 1908 ** for services of a 1909 ** peer device. When services.num_uuid is 0, it indicates all 1910 ** GATT based services are to be searched; other wise a list of 1911 ** UUID of interested services should be provided through 1912 ** p_services->p_uuid. 1913 ** 1914 ** 1915 ** 1916 ** Returns void 1917 ** 1918 *******************************************************************************/ 1919 extern void BTA_DmDiscoverByTransport(BD_ADDR bd_addr, tBTA_SERVICE_MASK_EXT *p_services, 1920 tBTA_DM_SEARCH_CBACK *p_cback, BOOLEAN sdp_search, 1921 tBTA_TRANSPORT transport); 1922 1923 /******************************************************************************* 1924 ** 1925 ** Function BTA_DmSetEncryption 1926 ** 1927 ** Description This function is called to ensure that connection is 1928 ** encrypted. Should be called only on an open connection. 1929 ** Typically only needed for connections that first want to 1930 ** bring up unencrypted links, then later encrypt them. 1931 ** 1932 ** Parameters: bd_addr - Address of the peer device 1933 ** transport - transport of the link to be encruypted 1934 ** p_callback - Pointer to callback function to indicat the 1935 ** link encryption status 1936 ** sec_act - This is the security action to indicate 1937 ** what knid of BLE security level is required for 1938 ** the BLE link if the BLE is supported 1939 ** Note: This parameter is ignored for the BR/EDR link 1940 ** or the BLE is not supported 1941 ** 1942 ** Returns void 1943 ** 1944 ** 1945 *******************************************************************************/ 1946 extern void BTA_DmSetEncryption(BD_ADDR bd_addr, tBTA_TRANSPORT transport, 1947 tBTA_DM_ENCRYPT_CBACK *p_callback, 1948 tBTA_DM_BLE_SEC_ACT sec_act); 1949 1950 1951 /******************************************************************************* 1952 ** 1953 ** Function BTA_DmBleObserve 1954 ** 1955 ** Description This procedure keep the device listening for advertising 1956 ** events from a broadcast device. 1957 ** 1958 ** Parameters start: start or stop observe. 1959 ** duration : Duration of the scan. Continuous scan if 0 is passed 1960 ** p_results_cb: Callback to be called with scan results 1961 ** 1962 ** Returns void 1963 ** 1964 *******************************************************************************/ 1965 extern void BTA_DmBleObserve(BOOLEAN start, UINT8 duration, 1966 tBTA_DM_SEARCH_CBACK *p_results_cb); 1967 1968 1969 #endif 1970 1971 #if BLE_INCLUDED == TRUE 1972 /******************************************************************************* 1973 ** 1974 ** Function BTA_DmBleConfigLocalPrivacy 1975 ** 1976 ** Description Enable/disable privacy on the local device 1977 ** 1978 ** Parameters: privacy_enable - enable/disabe privacy on remote device. 1979 ** 1980 ** Returns void 1981 ** 1982 *******************************************************************************/ 1983 extern void BTA_DmBleConfigLocalPrivacy(BOOLEAN privacy_enable); 1984 1985 /******************************************************************************* 1986 ** 1987 ** Function BTA_DmBleEnableRemotePrivacy 1988 ** 1989 ** Description Enable/disable privacy on a remote device 1990 ** 1991 ** Parameters: bd_addr - BD address of the peer 1992 ** privacy_enable - enable/disabe privacy on remote device. 1993 ** 1994 ** Returns void 1995 ** 1996 *******************************************************************************/ 1997 extern void BTA_DmBleEnableRemotePrivacy(BD_ADDR bd_addr, BOOLEAN privacy_enable); 1998 1999 2000 /******************************************************************************* 2001 ** 2002 ** Function BTA_DmBleSetAdvConfig 2003 ** 2004 ** Description This function is called to override the BTA default ADV parameters. 2005 ** 2006 ** Parameters Pointer to User defined ADV data structure 2007 ** 2008 ** Returns None 2009 ** 2010 *******************************************************************************/ 2011 extern void BTA_DmBleSetAdvConfig (tBTA_BLE_AD_MASK data_mask, 2012 tBTA_BLE_ADV_DATA *p_adv_cfg, 2013 tBTA_SET_ADV_DATA_CMPL_CBACK *p_adv_data_cback); 2014 2015 /******************************************************************************* 2016 ** 2017 ** Function BTA_DmBleSetScanRsp 2018 ** 2019 ** Description This function is called to override the BTA scan response. 2020 ** 2021 ** Parameters Pointer to User defined ADV data structure 2022 ** 2023 ** Returns None 2024 ** 2025 *******************************************************************************/ 2026 extern void BTA_DmBleSetScanRsp (tBTA_BLE_AD_MASK data_mask, 2027 tBTA_BLE_ADV_DATA *p_adv_cfg, 2028 tBTA_SET_ADV_DATA_CMPL_CBACK *p_adv_data_cback); 2029 2030 /******************************************************************************* 2031 ** 2032 ** Function BTA_DmBleBroadcast 2033 ** 2034 ** Description This function starts or stops LE broadcasting. 2035 ** 2036 ** Parameters start: start or stop broadcast. 2037 ** 2038 ** Returns None 2039 ** 2040 *******************************************************************************/ 2041 extern void BTA_DmBleBroadcast (BOOLEAN start); 2042 2043 2044 /******************************************************************************* 2045 ** 2046 ** Function BTA_BleEnableAdvInstance 2047 ** 2048 ** Description This function enables the Multi ADV instance feature 2049 ** 2050 ** Parameters p_params Pointer to ADV param user defined structure 2051 ** p_cback Pointer to Multi ADV callback structure 2052 ** p_ref - Reference pointer 2053 ** 2054 ** Returns None 2055 ** 2056 *******************************************************************************/ 2057 extern void BTA_BleEnableAdvInstance (tBTA_BLE_ADV_PARAMS *p_params, 2058 tBTA_BLE_MULTI_ADV_CBACK *p_cback,void *p_ref); 2059 2060 /******************************************************************************* 2061 ** 2062 ** Function BTA_BleUpdateAdvInstParam 2063 ** 2064 ** Description This function updates the Multi ADV instance params 2065 ** 2066 ** Parameters inst_id Instance ID 2067 ** p_params Pointer to ADV param user defined structure 2068 ** 2069 ** Returns None 2070 ** 2071 *******************************************************************************/ 2072 extern void BTA_BleUpdateAdvInstParam (UINT8 inst_id, 2073 tBTA_BLE_ADV_PARAMS *p_params); 2074 2075 /******************************************************************************* 2076 ** 2077 ** Function BTA_BleCfgAdvInstData 2078 ** 2079 ** Description This function is called to configure the ADV instance data 2080 ** 2081 ** Parameters inst_id - Instance ID 2082 ** is_scan_rsp - Boolean value Scan response 2083 ** Pointer to User defined ADV data structure 2084 ** Returns None 2085 ** 2086 *******************************************************************************/ 2087 extern void BTA_BleCfgAdvInstData (UINT8 inst_id, BOOLEAN is_scan_rsp, 2088 tBTA_BLE_AD_MASK data_mask, tBTA_BLE_ADV_DATA *p_data); 2089 2090 /******************************************************************************* 2091 ** 2092 ** Function BTA_BleDisableAdvInstance 2093 ** 2094 ** Description This function is called to disable the ADV instance 2095 ** 2096 ** Parameters inst_id - Instance ID to be disabled 2097 ** 2098 ** Returns None 2099 ** 2100 *******************************************************************************/ 2101 extern void BTA_BleDisableAdvInstance(UINT8 inst_id); 2102 2103 /******************************************************************************* 2104 ** 2105 ** Function BTA_DmBleUpdateConnectionParams 2106 ** 2107 ** Description Update connection parameters, can only be used when connection is up. 2108 ** 2109 ** Parameters: bd_addr - BD address of the peer 2110 ** min_int - minimum connection interval, [0x0004~ 0x4000] 2111 ** max_int - maximum connection interval, [0x0004~ 0x4000] 2112 ** latency - slave latency [0 ~ 500] 2113 ** timeout - supervision timeout [0x000a ~ 0xc80] 2114 ** 2115 ** Returns void 2116 ** 2117 *******************************************************************************/ 2118 extern void BTA_DmBleUpdateConnectionParams(BD_ADDR bd_addr, UINT16 min_int, 2119 UINT16 max_int, UINT16 latency, UINT16 timeout); 2120 2121 /******************************************************************************* 2122 ** 2123 ** Function BTA_DmBleSetDataLength 2124 ** 2125 ** Description This function is to set maximum LE data packet size 2126 ** 2127 ** Returns void 2128 ** 2129 *******************************************************************************/ 2130 extern void BTA_DmBleSetDataLength(BD_ADDR remote_device, UINT16 tx_data_length); 2131 2132 /******************************************************************************* 2133 ** 2134 ** Function BTA_DmBleSetStorageParams 2135 ** 2136 ** Description This function is called to set the storage parameters 2137 ** 2138 ** Parameters batch_scan_full_max -Max storage space (in %) allocated to full scanning 2139 ** batch_scan_trunc_max -Max storage space (in %) allocated to truncated scanning 2140 ** batch_scan_notify_threshold - Setup notification level based on total space 2141 ** consumed by both pools. Setting it to 0 will disable threshold notification 2142 ** p_setup_cback - Setup callback 2143 ** p_thres_cback - Threshold callback 2144 ** p_rep_cback - Reports callback 2145 ** ref_value - Reference value 2146 ** 2147 ** Returns None 2148 ** 2149 *******************************************************************************/ 2150 extern void BTA_DmBleSetStorageParams(UINT8 batch_scan_full_max, 2151 UINT8 batch_scan_trunc_max, 2152 UINT8 batch_scan_notify_threshold, 2153 tBTA_BLE_SCAN_SETUP_CBACK *p_setup_cback, 2154 tBTA_BLE_SCAN_THRESHOLD_CBACK *p_thres_cback, 2155 tBTA_BLE_SCAN_REP_CBACK* p_rep_cback, 2156 tBTA_DM_BLE_REF_VALUE ref_value); 2157 2158 /******************************************************************************* 2159 ** 2160 ** Function BTA_DmBleEnableBatchScan 2161 ** 2162 ** Description This function is called to enable the batch scan 2163 ** 2164 ** Parameters scan_mode -Batch scan mode 2165 ** scan_interval - Scan interval 2166 ** scan_window - Scan window 2167 ** discard_rule -Discard rules 2168 ** addr_type - Address type 2169 ** ref_value - Reference value 2170 ** 2171 ** Returns None 2172 ** 2173 *******************************************************************************/ 2174 extern void BTA_DmBleEnableBatchScan(tBTA_BLE_BATCH_SCAN_MODE scan_mode, 2175 UINT32 scan_interval, UINT32 scan_window, 2176 tBTA_BLE_DISCARD_RULE discard_rule, 2177 tBLE_ADDR_TYPE addr_type, 2178 tBTA_DM_BLE_REF_VALUE ref_value); 2179 2180 /******************************************************************************* 2181 ** 2182 ** Function BTA_DmBleReadScanReports 2183 ** 2184 ** Description This function is called to read the batch scan reports 2185 ** 2186 ** Parameters scan_mode -Batch scan mode 2187 ** ref_value - Reference value 2188 ** 2189 ** Returns None 2190 ** 2191 *******************************************************************************/ 2192 extern void BTA_DmBleReadScanReports(tBTA_BLE_BATCH_SCAN_MODE scan_type, 2193 tBTA_DM_BLE_REF_VALUE ref_value); 2194 2195 /******************************************************************************* 2196 ** 2197 ** Function BTA_DmBleDisableBatchScan 2198 ** 2199 ** Description This function is called to disable the batch scanning 2200 ** 2201 ** Parameters ref_value - Reference value 2202 ** 2203 ** Returns None 2204 ** 2205 *******************************************************************************/ 2206 extern void BTA_DmBleDisableBatchScan(tBTA_DM_BLE_REF_VALUE ref_value); 2207 2208 /******************************************************************************* 2209 ** 2210 ** Function BTA_DmEnableScanFilter 2211 ** 2212 ** Description This function is called to enable the adv data payload filter 2213 ** 2214 ** Parameters action - enable or disable the APCF feature 2215 ** p_cmpl_cback - Command completed callback 2216 ** ref_value - Reference value 2217 ** 2218 ** Returns void 2219 ** 2220 *******************************************************************************/ 2221 extern void BTA_DmEnableScanFilter(UINT8 action, 2222 tBTA_DM_BLE_PF_STATUS_CBACK *p_cmpl_cback, 2223 tBTA_DM_BLE_REF_VALUE ref_value); 2224 2225 /******************************************************************************* 2226 ** 2227 ** Function BTA_DmBleScanFilterSetup 2228 ** 2229 ** Description This function is called to setup the filter params 2230 ** 2231 ** Parameters p_target: enable the filter condition on a target device; if NULL 2232 ** filt_index - Filter index 2233 ** p_filt_params -Filter parameters 2234 ** ref_value - Reference value 2235 ** action - Add, delete or clear 2236 ** p_cmpl_back - Command completed callback 2237 ** 2238 ** Returns void 2239 ** 2240 *******************************************************************************/ 2241 extern void BTA_DmBleScanFilterSetup(UINT8 action, 2242 tBTA_DM_BLE_PF_FILT_INDEX filt_index, 2243 tBTA_DM_BLE_PF_FILT_PARAMS *p_filt_params, 2244 tBLE_BD_ADDR *p_target, 2245 tBTA_DM_BLE_PF_PARAM_CBACK *p_cmpl_cback, 2246 tBTA_DM_BLE_REF_VALUE ref_value); 2247 2248 /******************************************************************************* 2249 ** 2250 ** Function BTA_DmBleCfgFilterCondition 2251 ** 2252 ** Description This function is called to configure the adv data payload filter 2253 ** condition. 2254 ** 2255 ** Parameters action: to read/write/clear 2256 ** cond_type: filter condition type 2257 ** filt_index - Filter index 2258 ** p_cond: filter condition parameter 2259 ** p_cmpl_back - Command completed callback 2260 ** ref_value - Reference value 2261 ** 2262 ** Returns void 2263 ** 2264 *******************************************************************************/ 2265 extern void BTA_DmBleCfgFilterCondition(tBTA_DM_BLE_SCAN_COND_OP action, 2266 tBTA_DM_BLE_PF_COND_TYPE cond_type, 2267 tBTA_DM_BLE_PF_FILT_INDEX filt_index, 2268 tBTA_DM_BLE_PF_COND_PARAM *p_cond, 2269 tBTA_DM_BLE_PF_CFG_CBACK *p_cmpl_cback, 2270 tBTA_DM_BLE_REF_VALUE ref_value); 2271 2272 2273 /******************************************************************************* 2274 ** 2275 ** Function BTA_DmBleTrackAdvertiser 2276 ** 2277 ** Description This function is called to track the advertiser 2278 ** 2279 ** Parameters ref_value - Reference value 2280 ** p_track_adv_cback - ADV callback 2281 ** 2282 ** Returns None 2283 ** 2284 *******************************************************************************/ 2285 extern void BTA_DmBleTrackAdvertiser(tBTA_DM_BLE_REF_VALUE ref_value, 2286 tBTA_BLE_TRACK_ADV_CBACK *p_track_adv_cback); 2287 2288 /******************************************************************************* 2289 ** 2290 ** Function BTA_DmBleGetEnergyInfo 2291 ** 2292 ** Description This function is called to obtain the energy info 2293 ** 2294 ** Parameters p_cmpl_cback - Command complete callback 2295 ** 2296 ** Returns void 2297 ** 2298 *******************************************************************************/ 2299 extern void BTA_DmBleGetEnergyInfo(tBTA_BLE_ENERGY_INFO_CBACK *p_cmpl_cback); 2300 2301 /******************************************************************************* 2302 ** 2303 ** Function BTA_BrcmInit 2304 ** 2305 ** Description This function initializes Broadcom specific VS handler in BTA 2306 ** 2307 ** Returns void 2308 ** 2309 *******************************************************************************/ 2310 extern void BTA_VendorInit (void); 2311 2312 /******************************************************************************* 2313 ** 2314 ** Function BTA_BrcmCleanup 2315 ** 2316 ** Description This function frees up Broadcom specific VS specific dynamic memory 2317 ** 2318 ** Returns void 2319 ** 2320 *******************************************************************************/ 2321 extern void BTA_VendorCleanup (void); 2322 2323 #endif 2324 2325 #ifdef __cplusplus 2326 } 2327 #endif 2328 2329 #endif /* BTA_API_H */ 2330