/******************************************************************************
 *
 *  Copyright (C) 2011-2014 Broadcom Corporation
 *
 *  Licensed under the Apache License, Version 2.0 (the "License");
 *  you may not use this file except in compliance with the License.
 *  You may obtain a copy of the License at:
 *
 *  http://www.apache.org/licenses/LICENSE-2.0
 *
 *  Unless required by applicable law or agreed to in writing, software
 *  distributed under the License is distributed on an "AS IS" BASIS,
 *  WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied.
 *  See the License for the specific language governing permissions and
 *  limitations under the License.
 *
 ******************************************************************************/

/******************************************************************************
 *
 *  This file contains compile-time configurable constants for BRCM HAL
 *  modules
 *
 ******************************************************************************/
#include "nci_defs.h"
#include "nfc_brcm_defs.h"
#include "nfc_hal_int.h"

/* the SetConfig at start up*/
uint8_t nfc_hal_start_up_cfg[] = {
    /* TLV len */ 31,
    /* B0 */ NCI_PARAM_ID_EMVCO_ENABLE,
    /* B1 */ 1,
    /* B2 */
    1, /* (1 = enable emvco mode, 0 = disable emvco mode) Default = 0.*/
    /* B3 */ NCI_PARAM_ID_CONTINUE_MODE, /* NFCC will restart discovery
                                            after deactivated */
    /* B4 */ 1,
    /* B5 */ 1, /* (1 = enable, 0 = disable) Default = 0.*/
    /* B6 */ NCI_PARAM_ID_RFU_CONFIG,
    /* B7 */ 0x14,
    /* B8 */ 0x00,
    /* B9 */ 0x00,
    /* B10*/ 0x00,
    /* B11*/ 0x00,
    /* B12*/ 0x0E,
    /* B13*/ 0xE8,
    /* B14*/ 0xF0,
    /* B15*/ 0x55,
    /* B16*/ 0x00,
    /* B17*/ 0x0F, /* CE3 SO delay in sec */
    /* B18*/ 0x00,
    /* B19*/ 0x00,
    /* B20*/ 0x00,
    /* B21*/ 0x00,
    /* B22*/ 0x00,
    /* B23*/ 0x00,
    /* B24*/ 0x00,
    /* B25*/ 0x00,
    /* B26*/ 0x00,
    /* B27*/ 0x00,
    /* B28*/ NCI_PARAM_ID_ACT_ORDER, /* polling sequence */
    /* B29*/ 1,
    /* B30*/ 1, /* (1 = active mode polling before passive, 0 = passive
                   polling first) Default = 0.*/
};

uint8_t* p_nfc_hal_dm_start_up_cfg = (uint8_t*)nfc_hal_start_up_cfg;

/* the VSCs at start up:
 * The VSCs are specified in TLV format similar to nfa_start_up_cfg[]
 * first byte is the TLV total len.
 * B0 is the first T; i.e. the opcode for the VSC
 * B1 is the len of the VSC parameters/payload
 * */
uint8_t nfc_hal_dm_start_up_vsc_cfg[] = {
    /* TLV len */ 5,
    /* B0 */ NCI_MTS_CMD | NCI_GID_PROP,
    /* B1 */ NCI_MSG_FRAME_LOG,
    /* B2 */ 2,
    /* B3 */ 0, /* 1 to enable RF frames */
    /* B4 */ 1  /* 1 to enable SWP frames */
};

uint8_t* p_nfc_hal_dm_start_up_vsc_cfg = NULL;

/* the SetConfig at HAL_NfcPreDiscover. This is done once after HAL_NfcOpen */
uint8_t nfc_hal_pre_discover_cfg[] = {
    /* TLV len */ 0x0A,
    /* B0 */ NCI_PARAM_ID_SWPCFG,
    /* B1 */ 0x08,
    /* B2 */ 0x01,
    /* B3 */ 0x08,
    /* B4 */ 0x00,
    /* B5 */ 0x04,
    /* B6 */ 0x80,
    /* B7 */ 0xC3,
    /* B8 */ 0xC9,
    /* B9 */ 0x01};

uint8_t* p_nfc_hal_pre_discover_cfg = NULL;

/* LPTD parameters (LowPowerTagDetection)
 * This is typical values for 20791B2
 * The timing and threshold parameters used for a customer handset/hardware may
 * vary
 * depending on antenna and should be verified during a customer testing phase.
 * the data fields without comments are too complicated. Please see ""
 * */
const uint8_t nfc_hal_dm_lptd_cfg[] = {
    21,                        /* total TLV length excluding itself */
    NCI_PARAM_ID_TAGSNIFF_CFG, /* type */
    19,                        /* length */
    0x01,                      /* B0 enable: 0/disable, 1/enable*/
    0x02, /* B1 poll count: number of full power poll before starting lptd
             poll */
    0xFF, /* B2 sniff count lsb: number of lptd poll before switching to
             full power poll */
    0xFF, /* B3 sniff count msb */
    0x80, /* B4 threshold: Bigger thresholds give a smaller LPTD range but
             more immunity to false detections. Smaller thresholds increase
             LPTD range at the cost of greater likelihood of false
             detections. */
    0x40, /* B5 delay lsb: delay (us) to sampling power */
    0x00, /* B6 delay msb */
    0x40, /* B7 carrier threshold lsb */
    0x00, /* B8 carrier threshold msb */
    0x80, /* B9 mode: Bitwise variable used to enable various algorithm
             modes.*/
    0x80, /* B10 0-offset lsb */
    0x00, /* B11 0-offset msb */
    0x10, /* B12 field sense time lsb */
    0x00, /* B13 field sense time msb */
    0x00, /* B14 false detect threshold lsb: 0x00 to disable LPTD NTF. The
             number of false tag detections to resport LPTD NTF. */
    0x00, /* B15 false detect threshold msb. A false tag detect - full poll
             results in no tag being detected.*/
    0x75, /* B16 mode1; Bitwise variable used to enable various algorithm
             modes. */
    0x0D, /* B17 lptd ant cfg rx */
    0x30, /* B18 lptd rdr cfg ve */
};

uint8_t* p_nfc_hal_dm_lptd_cfg = (uint8_t*)&nfc_hal_dm_lptd_cfg[0];

/*
** NFCC has a table which has 9 XTAL frequencies: 9.6, 13, 16.2,  19.2, 24, 26,
*38.4, 52 and 37.4 in MHz.
** For these 9 xtal frequencies, host doesn't need to configure PLL325.
** For 43341, host doesn't need to configure it at all.
*/
uint8_t* p_nfc_hal_dm_pll_325_cfg = NULL;

/*
** Proprietary pre-set is required, if not NULL.
*/
tNFC_HAL_DM_PRE_SET_MEM* p_nfc_hal_dm_pre_set_mem = NULL;

tNFC_HAL_CFG nfc_hal_cfg = {
    false, /* set nfc_hal_prm_nvm_required to TRUE, if the platform wants to
              abort PRM process without NVM */
    (uint16_t)NFC_HAL_NFCC_ENABLE_TIMEOUT, /* max time to wait for RESET NTF
                                         *after setting REG_PU to high
                                         ** If NFCC doesn't have NVM or cannot
                                         *load patch from NVM without Xtal
                                         *setting
                                         ** then set it to short to optimize
                                         *bootup time because NFCC cannot send
                                         *RESET NTF.
                                         ** Otherwise, it depends on NVM type
                                         *and size of patchram.
                                         */
    (uint16_t)NFC_HAL_NFCC_ENABLE_TIMEOUT  /* max time to wait for RESET NTF
                                         *after setting Xtal frequency
                                         ** It depends on NVM type and size of
                                         *patchram.
                                         */
#if (NFC_HAL_HCI_INCLUDED == TRUE)
    ,
    true, /* set nfc_hal_first_boot to TRUE, if platform enables NFC for the
             first time after bootup */
    (HAL_NFC_HCI_UICC0_HOST | HAL_NFC_HCI_UICC1_HOST |
     HAL_NFC_HCI_UICC2_HOST) /* Set bit(s) for supported UICC(s) */
#endif
};

tNFC_HAL_CFG* p_nfc_hal_cfg = (tNFC_HAL_CFG*)&nfc_hal_cfg;

const uint8_t nfc_hal_dm_xtal_params_cfg[] = {
    8,    /* length */
    0x00, /* B0 Rfpll_cfg_pll_xtal_div_2                  */
    0x00, /* B1 Rfpll_cfg_pll_vcocal1_0_cal_ref_timeout   */
    0x00, /* B2 Rfpll_cfg_pll_vcocal2_cal_count           */
    0x00, /* B3 Rfpll_cfg_pll_vcocal3_cal_count           */
    0x00, /* B4 Rfpll_cfg_pll_dsm_b_msb_wild_base         */
    0x00, /* B5 Rfpll_cfg_pll_dsm_b_lsb_3_wild_base_3     */
    0x00, /* B6 Rfpll_cfg_pll_dsm_b_lsb_2_wild_base_2     */
    0x00  /* B7 Rfpll_cfg_pll_dsm_b_lsb_1_wild_base_1     */
};

/* By default, the XTAL command does not need these extra params. */
uint8_t* p_nfc_hal_dm_xtal_params_cfg = NULL;