1 /* 2 * Qualcomm Atheros OUI and vendor specific assignments 3 * Copyright (c) 2014-2017, Qualcomm Atheros, Inc. 4 * Copyright (c) 2018, The Linux Foundation 5 * 6 * This software may be distributed under the terms of the BSD license. 7 * See README for more details. 8 */ 9 10 #ifndef QCA_VENDOR_H 11 #define QCA_VENDOR_H 12 13 /* 14 * This file is a registry of identifier assignments from the Qualcomm Atheros 15 * OUI 00:13:74 for purposes other than MAC address assignment. New identifiers 16 * can be assigned through normal review process for changes to the upstream 17 * hostap.git repository. 18 */ 19 20 #define OUI_QCA 0x001374 21 22 /** 23 * enum qca_radiotap_vendor_ids - QCA radiotap vendor namespace IDs 24 */ 25 enum qca_radiotap_vendor_ids { 26 QCA_RADIOTAP_VID_WLANTEST = 0, 27 }; 28 29 /** 30 * enum qca_nl80211_vendor_subcmds - QCA nl80211 vendor command identifiers 31 * 32 * @QCA_NL80211_VENDOR_SUBCMD_UNSPEC: Reserved value 0 33 * 34 * @QCA_NL80211_VENDOR_SUBCMD_TEST: Test command/event 35 * 36 * @QCA_NL80211_VENDOR_SUBCMD_ROAMING: Set roaming policy for drivers that use 37 * internal BSS-selection. This command uses 38 * @QCA_WLAN_VENDOR_ATTR_ROAMING_POLICY to specify the new roaming policy 39 * for the current connection (i.e., changes policy set by the nl80211 40 * Connect command). @QCA_WLAN_VENDOR_ATTR_MAC_ADDR may optionally be 41 * included to indicate which BSS to use in case roaming is disabled. 42 * 43 * @QCA_NL80211_VENDOR_SUBCMD_AVOID_FREQUENCY: Recommendation of frequency 44 * ranges to avoid to reduce issues due to interference or internal 45 * co-existence information in the driver. These frequencies aim to 46 * minimize the traffic but not to totally avoid the traffic. That said 47 * for a P2P use case, these frequencies are allowed for the P2P 48 * discovery/negotiation but avoid the group to get formed on these 49 * frequencies. The event data structure is defined in 50 * struct qca_avoid_freq_list. 51 * 52 * @QCA_NL80211_VENDOR_SUBCMD_DFS_CAPABILITY: Command to check driver support 53 * for DFS offloading. 54 * 55 * @QCA_NL80211_VENDOR_SUBCMD_NAN: NAN command/event which is used to pass 56 * NAN Request/Response and NAN Indication messages. These messages are 57 * interpreted between the framework and the firmware component. While 58 * sending the command from userspace to the driver, payload is not 59 * encapsulated inside any attribute. Attribute QCA_WLAN_VENDOR_ATTR_NAN 60 * is used when receiving vendor events in userspace from the driver. 61 * 62 * @QCA_NL80211_VENDOR_SUBCMD_KEY_MGMT_SET_KEY: Set key operation that can be 63 * used to configure PMK to the driver even when not connected. This can 64 * be used to request offloading of key management operations. Only used 65 * if device supports QCA_WLAN_VENDOR_FEATURE_KEY_MGMT_OFFLOAD. 66 * 67 * @QCA_NL80211_VENDOR_SUBCMD_KEY_MGMT_ROAM_AUTH: An extended version of 68 * NL80211_CMD_ROAM event with optional attributes including information 69 * from offloaded key management operation. Uses 70 * enum qca_wlan_vendor_attr_roam_auth attributes. Only used 71 * if device supports QCA_WLAN_VENDOR_FEATURE_KEY_MGMT_OFFLOAD. 72 * 73 * @QCA_NL80211_VENDOR_SUBCMD_DO_ACS: ACS command/event which is used to 74 * invoke the ACS function in device and pass selected channels to 75 * hostapd. 76 * 77 * @QCA_NL80211_VENDOR_SUBCMD_GET_FEATURES: Command to get the features 78 * supported by the driver. enum qca_wlan_vendor_features defines 79 * the possible features. 80 * 81 * @QCA_NL80211_VENDOR_SUBCMD_DFS_OFFLOAD_CAC_STARTED: Event used by driver, 82 * which supports DFS offloading, to indicate a channel availability check 83 * start. 84 * 85 * @QCA_NL80211_VENDOR_SUBCMD_DFS_OFFLOAD_CAC_FINISHED: Event used by driver, 86 * which supports DFS offloading, to indicate a channel availability check 87 * completion. 88 * 89 * @QCA_NL80211_VENDOR_SUBCMD_DFS_OFFLOAD_CAC_ABORTED: Event used by driver, 90 * which supports DFS offloading, to indicate that the channel availability 91 * check aborted, no change to the channel status. 92 * 93 * @QCA_NL80211_VENDOR_SUBCMD_DFS_OFFLOAD_CAC_NOP_FINISHED: Event used by 94 * driver, which supports DFS offloading, to indicate that the 95 * Non-Occupancy Period for this channel is over, channel becomes usable. 96 * 97 * @QCA_NL80211_VENDOR_SUBCMD_DFS_OFFLOAD_RADAR_DETECTED: Event used by driver, 98 * which supports DFS offloading, to indicate a radar pattern has been 99 * detected. The channel is now unusable. 100 * 101 * @QCA_NL80211_VENDOR_SUBCMD_GET_LOGGER_FEATURE_SET: Get the feature bitmap 102 * based on enum wifi_logger_supported_features. Attributes defined in 103 * enum qca_wlan_vendor_attr_get_logger_features. 104 * 105 * @QCA_NL80211_VENDOR_SUBCMD_GET_RING_DATA: Get the ring data from a particular 106 * logger ring, QCA_WLAN_VENDOR_ATTR_WIFI_LOGGER_RING_ID is passed as the 107 * attribute for this command. Attributes defined in 108 * enum qca_wlan_vendor_attr_wifi_logger_start. 109 * 110 * @QCA_NL80211_VENDOR_SUBCMD_TDLS_GET_CAPABILITIES: Get the supported TDLS 111 * capabilities of the driver, parameters includes the attributes defined 112 * in enum qca_wlan_vendor_attr_tdls_get_capabilities. 113 * 114 * @QCA_NL80211_VENDOR_SUBCMD_OFFLOADED_PACKETS: Vendor command used to offload 115 * sending of certain periodic IP packet to firmware, attributes defined in 116 * enum qca_wlan_vendor_attr_offloaded_packets. 117 * 118 * @QCA_NL80211_VENDOR_SUBCMD_MONITOR_RSSI: Command used to configure RSSI 119 * monitoring, defines min and max RSSI which are configured for RSSI 120 * monitoring. Also used to notify the RSSI breach and provides the BSSID 121 * and RSSI value that was breached. Attributes defined in 122 * enum qca_wlan_vendor_attr_rssi_monitoring. 123 * 124 * @QCA_NL80211_VENDOR_SUBCMD_NDP: Command used for performing various NAN 125 * Data Path (NDP) related operations, attributes defined in 126 * enum qca_wlan_vendor_attr_ndp_params. 127 * 128 * @QCA_NL80211_VENDOR_SUBCMD_ND_OFFLOAD: Command used to enable/disable 129 * Neighbour Discovery offload, attributes defined in 130 * enum qca_wlan_vendor_attr_nd_offload. 131 * 132 * @QCA_NL80211_VENDOR_SUBCMD_PACKET_FILTER: Used to set/get the various 133 * configuration parameter for BPF packet filter, attributes defined in 134 * enum qca_wlan_vendor_attr_packet_filter. 135 * 136 * @QCA_NL80211_VENDOR_SUBCMD_GET_BUS_SIZE: Gets the driver-firmware 137 * maximum supported size, attributes defined in 138 * enum qca_wlan_vendor_drv_info. 139 * 140 * @QCA_NL80211_VENDOR_SUBCMD_GET_WAKE_REASON_STATS: Command to get various 141 * data about wake reasons and datapath IP statistics, attributes defined 142 * in enum qca_wlan_vendor_attr_wake_stats. 143 * 144 * @QCA_NL80211_VENDOR_SUBCMD_OCB_SET_CONFIG: Command used to set configuration 145 * for IEEE 802.11 communicating outside the context of a basic service 146 * set, called OCB command. Uses the attributes defines in 147 * enum qca_wlan_vendor_attr_ocb_set_config. 148 * 149 * @QCA_NL80211_VENDOR_SUBCMD_OCB_SET_UTC_TIME: Command used to set OCB 150 * UTC time. Use the attributes defines in 151 * enum qca_wlan_vendor_attr_ocb_set_utc_time. 152 * 153 * @QCA_NL80211_VENDOR_SUBCMD_OCB_START_TIMING_ADVERT: Command used to start 154 * sending OCB timing advert frames. Uses the attributes defines in 155 * enum qca_wlan_vendor_attr_ocb_start_timing_advert. 156 * 157 * @QCA_NL80211_VENDOR_SUBCMD_OCB_STOP_TIMING_ADVERT: Command used to stop 158 * OCB timing advert. Uses the attributes defines in 159 * enum qca_wlan_vendor_attr_ocb_stop_timing_advert. 160 * 161 * @QCA_NL80211_VENDOR_SUBCMD_OCB_GET_TSF_TIMER: Command used to get TSF 162 * timer value. Uses the attributes defines in 163 * enum qca_wlan_vendor_attr_ocb_get_tsf_resp. 164 * 165 * @QCA_NL80211_VENDOR_SUBCMD_LINK_PROPERTIES: Command/event to update the 166 * link properties of the respective interface. As an event, is used 167 * to notify the connected station's status. The attributes for this 168 * command are defined in enum qca_wlan_vendor_attr_link_properties. 169 * 170 * @QCA_NL80211_VENDOR_SUBCMD_P2P_LISTEN_OFFLOAD_START: Command used to 171 * start the P2P Listen offload function in device and pass the listen 172 * channel, period, interval, count, device types, and vendor specific 173 * information elements to the device driver and firmware. 174 * Uses the attributes defines in 175 * enum qca_wlan_vendor_attr_p2p_listen_offload. 176 * 177 * @QCA_NL80211_VENDOR_SUBCMD_P2P_LISTEN_OFFLOAD_STOP: Command/event used to 178 * indicate stop request/response of the P2P Listen offload function in 179 * device. As an event, it indicates either the feature stopped after it 180 * was already running or feature has actually failed to start. Uses the 181 * attributes defines in enum qca_wlan_vendor_attr_p2p_listen_offload. 182 * 183 * @QCA_NL80211_VENDOR_SUBCMD_SAP_CONDITIONAL_CHAN_SWITCH: After AP starts 184 * beaconing, this sub command provides the driver, the frequencies on the 185 * 5 GHz band to check for any radar activity. Driver selects one channel 186 * from this priority list provided through 187 * @QCA_WLAN_VENDOR_ATTR_SAP_CONDITIONAL_CHAN_SWITCH_FREQ_LIST and starts 188 * to check for radar activity on it. If no radar activity is detected 189 * during the channel availability check period, driver internally switches 190 * to the selected frequency of operation. If the frequency is zero, driver 191 * internally selects a channel. The status of this conditional switch is 192 * indicated through an event using the same sub command through 193 * @QCA_WLAN_VENDOR_ATTR_SAP_CONDITIONAL_CHAN_SWITCH_STATUS. Attributes are 194 * listed in qca_wlan_vendor_attr_sap_conditional_chan_switch. 195 * 196 * @QCA_NL80211_VENDOR_SUBCMD_GPIO_CONFIG_COMMAND: Set GPIO pins. This uses the 197 * attributes defined in enum qca_wlan_gpio_attr. 198 * 199 * @QCA_NL80211_VENDOR_SUBCMD_GET_HW_CAPABILITY: Fetch hardware capabilities. 200 * This uses @QCA_WLAN_VENDOR_ATTR_GET_HW_CAPABILITY to indicate which 201 * capabilities are to be fetched and other 202 * enum qca_wlan_vendor_attr_get_hw_capability attributes to return the 203 * requested capabilities. 204 * 205 * @QCA_NL80211_VENDOR_SUBCMD_LL_STATS_EXT: Link layer statistics extension. 206 * enum qca_wlan_vendor_attr_ll_stats_ext attributes are used with this 207 * command and event. 208 * 209 * @QCA_NL80211_VENDOR_SUBCMD_LOC_GET_CAPA: Get capabilities for 210 * indoor location features. Capabilities are reported in 211 * QCA_WLAN_VENDOR_ATTR_LOC_CAPA. 212 * 213 * @QCA_NL80211_VENDOR_SUBCMD_FTM_START_SESSION: Start an FTM 214 * (fine timing measurement) session with one or more peers. 215 * Specify Session cookie in QCA_WLAN_VENDOR_ATTR_FTM_SESSION_COOKIE and 216 * peer information in QCA_WLAN_VENDOR_ATTR_FTM_MEAS_PEERS. 217 * On success, 0 or more QCA_NL80211_VENDOR_SUBCMD_FTM_MEAS_RESULT 218 * events will be reported, followed by 219 * QCA_NL80211_VENDOR_SUBCMD_FTM_SESSION_DONE event to indicate 220 * end of session. 221 * Refer to IEEE P802.11-REVmc/D7.0, 11.24.6 222 * 223 * @QCA_NL80211_VENDOR_SUBCMD_FTM_ABORT_SESSION: Abort a running session. 224 * A QCA_NL80211_VENDOR_SUBCMD_FTM_SESSION_DONE will be reported with 225 * status code indicating session was aborted. 226 * 227 * @QCA_NL80211_VENDOR_SUBCMD_FTM_MEAS_RESULT: Event with measurement 228 * results for one peer. Results are reported in 229 * QCA_WLAN_VENDOR_ATTR_FTM_MEAS_PEER_RESULTS. 230 * 231 * @QCA_NL80211_VENDOR_SUBCMD_FTM_SESSION_DONE: Event triggered when 232 * FTM session is finished, either successfully or aborted by 233 * request. 234 * 235 * @QCA_NL80211_VENDOR_SUBCMD_FTM_CFG_RESPONDER: Configure FTM responder 236 * mode. QCA_WLAN_VENDOR_ATTR_FTM_RESPONDER_ENABLE specifies whether 237 * to enable or disable the responder. LCI/LCR reports can be 238 * configured with QCA_WLAN_VENDOR_ATTR_FTM_LCI and 239 * QCA_WLAN_VENDOR_ATTR_FTM_LCR. Can be called multiple 240 * times to update the LCI/LCR reports. 241 * 242 * @QCA_NL80211_VENDOR_SUBCMD_AOA_MEAS: Perform a standalone AOA (angle of 243 * arrival) measurement with a single peer. Specify peer MAC address in 244 * QCA_WLAN_VENDOR_ATTR_MAC_ADDR and optionally frequency (MHz) in 245 * QCA_WLAN_VENDOR_ATTR_FREQ (if not specified, locate peer in kernel 246 * scan results cache and use the frequency from there). 247 * Also specify measurement type in QCA_WLAN_VENDOR_ATTR_AOA_TYPE. 248 * Measurement result is reported in 249 * QCA_NL80211_VENDOR_SUBCMD_AOA_MEAS_RESULT event. 250 * 251 * @QCA_NL80211_VENDOR_SUBCMD_AOA_ABORT_MEAS: Abort an AOA measurement. Specify 252 * peer MAC address in QCA_WLAN_VENDOR_ATTR_MAC_ADDR. 253 * 254 * @QCA_NL80211_VENDOR_SUBCMD_AOA_MEAS_RESULT: Event that reports 255 * the AOA measurement result. 256 * Peer MAC address reported in QCA_WLAN_VENDOR_ATTR_MAC_ADDR. 257 * success/failure status is reported in 258 * QCA_WLAN_VENDOR_ATTR_LOC_SESSION_STATUS. 259 * Measurement data is reported in QCA_WLAN_VENDOR_ATTR_AOA_MEAS_RESULT. 260 * The antenna array(s) used in the measurement are reported in 261 * QCA_WLAN_VENDOR_ATTR_LOC_ANTENNA_ARRAY_MASK. 262 * 263 * @QCA_NL80211_VENDOR_SUBCMD_ENCRYPTION_TEST: Encrypt/decrypt the given 264 * data as per the given parameters. 265 * 266 * @QCA_NL80211_VENDOR_SUBCMD_GET_CHAIN_RSSI: Get antenna RSSI value for a 267 * specific chain. 268 * 269 * @QCA_NL80211_VENDOR_SUBCMD_DMG_RF_GET_SECTOR_CFG: Get low level 270 * configuration for a DMG RF sector. Specify sector index in 271 * QCA_WLAN_VENDOR_ATTR_DMG_RF_SECTOR_INDEX, sector type in 272 * QCA_WLAN_VENDOR_ATTR_DMG_RF_SECTOR_TYPE and RF modules 273 * to return sector information for in 274 * QCA_WLAN_VENDOR_ATTR_DMG_RF_MODULE_MASK. Returns sector configuration 275 * in QCA_WLAN_VENDOR_ATTR_DMG_RF_SECTOR_CFG. Also return the 276 * exact time where information was captured in 277 * QCA_WLAN_VENDOR_ATTR_TSF. 278 * 279 * @QCA_NL80211_VENDOR_SUBCMD_DMG_RF_SET_SECTOR_CFG: Set low level 280 * configuration for a DMG RF sector. Specify sector index in 281 * QCA_WLAN_VENDOR_ATTR_DMG_RF_SECTOR_INDEX, sector type in 282 * QCA_WLAN_VENDOR_ATTR_DMG_RF_SECTOR_TYPE and sector configuration 283 * for one or more DMG RF modules in 284 * QCA_WLAN_VENDOR_ATTR_DMG_RF_SECTOR_CFG. 285 * 286 * @QCA_NL80211_VENDOR_SUBCMD_DMG_RF_GET_SELECTED_SECTOR: Get selected 287 * DMG RF sector for a station. This is the sector that the HW 288 * will use to communicate with the station. Specify the MAC address 289 * of associated station/AP/PCP in QCA_WLAN_VENDOR_ATTR_MAC_ADDR (not 290 * needed for unassociated station). Specify sector type to return in 291 * QCA_WLAN_VENDOR_ATTR_DMG_RF_SECTOR_TYPE. Returns the selected 292 * sector index in QCA_WLAN_VENDOR_ATTR_DMG_RF_SECTOR_INDEX. 293 * Also return the exact time where the information was captured 294 * in QCA_WLAN_VENDOR_ATTR_TSF. 295 * 296 * @QCA_NL80211_VENDOR_SUBCMD_DMG_RF_SET_SELECTED_SECTOR: Set the 297 * selected DMG RF sector for a station. This is the sector that 298 * the HW will use to communicate with the station. 299 * Specify the MAC address of associated station/AP/PCP in 300 * QCA_WLAN_VENDOR_ATTR_MAC_ADDR, the sector type to select in 301 * QCA_WLAN_VENDOR_ATTR_DMG_RF_SECTOR_TYPE and the sector index 302 * in QCA_WLAN_VENDOR_ATTR_DMG_RF_SECTOR_INDEX. 303 * The selected sector will be locked such that it will not be 304 * modified like it normally does (for example when station 305 * moves around). To unlock the selected sector for a station 306 * pass the special value 0xFFFF in the sector index. To unlock 307 * all connected stations also pass a broadcast MAC address. 308 * 309 * @QCA_NL80211_VENDOR_SUBCMD_CONFIGURE_TDLS: Configure the TDLS behavior 310 * in the host driver. The different TDLS configurations are defined 311 * by the attributes in enum qca_wlan_vendor_attr_tdls_configuration. 312 * 313 * @QCA_NL80211_VENDOR_SUBCMD_GET_HE_CAPABILITIES: Query device IEEE 802.11ax HE 314 * capabilities. The response uses the attributes defined in 315 * enum qca_wlan_vendor_attr_get_he_capabilities. 316 * 317 * @QCA_NL80211_VENDOR_SUBCMD_ABORT_SCAN: Abort an ongoing vendor scan that was 318 * started with QCA_NL80211_VENDOR_SUBCMD_TRIGGER_SCAN. This command 319 * carries the scan cookie of the corresponding scan request. The scan 320 * cookie is represented by QCA_WLAN_VENDOR_ATTR_SCAN_COOKIE. 321 * 322 * @QCA_NL80211_VENDOR_SUBCMD_SET_SAR_LIMITS: Set the Specific 323 * Absorption Rate (SAR) power limits. A critical regulation for 324 * FCC compliance, OEMs require methods to set SAR limits on TX 325 * power of WLAN/WWAN. enum qca_vendor_attr_sar_limits 326 * attributes are used with this command. 327 * 328 * @QCA_NL80211_VENDOR_SUBCMD_EXTERNAL_ACS: This command/event is used by the 329 * host driver for offloading the implementation of Auto Channel Selection 330 * (ACS) to an external user space entity. This interface is used as the 331 * event from the host driver to the user space entity and also as the 332 * request from the user space entity to the host driver. The event from 333 * the host driver is used by the user space entity as an indication to 334 * start the ACS functionality. The attributes used by this event are 335 * represented by the enum qca_wlan_vendor_attr_external_acs_event. 336 * User space entity uses the same interface to inform the host driver with 337 * selected channels after the ACS operation using the attributes defined 338 * by enum qca_wlan_vendor_attr_external_acs_channels. 339 * 340 * @QCA_NL80211_VENDOR_SUBCMD_CHIP_PWRSAVE_FAILURE: Vendor event carrying the 341 * requisite information leading to a power save failure. The information 342 * carried as part of this event is represented by the 343 * enum qca_attr_chip_power_save_failure attributes. 344 * 345 * @QCA_NL80211_VENDOR_SUBCMD_NUD_STATS_SET: Start/Stop the NUD statistics 346 * collection. Uses attributes defined in enum qca_attr_nud_stats_set. 347 * 348 * @QCA_NL80211_VENDOR_SUBCMD_NUD_STATS_GET: Get the NUD statistics. These 349 * statistics are represented by the enum qca_attr_nud_stats_get 350 * attributes. 351 * 352 * @QCA_NL80211_VENDOR_SUBCMD_FETCH_BSS_TRANSITION_STATUS: Sub-command to fetch 353 * the BSS transition status, whether accept or reject, for a list of 354 * candidate BSSIDs provided by the userspace. This uses the vendor 355 * attributes QCA_WLAN_VENDOR_ATTR_BTM_MBO_TRANSITION_REASON and 356 * QCA_WLAN_VENDOR_ATTR_BTM_CANDIDATE_INFO. The userspace shall specify 357 * the attributes QCA_WLAN_VENDOR_ATTR_BTM_MBO_TRANSITION_REASON and an 358 * array of QCA_WLAN_VENDOR_ATTR_BTM_CANDIDATE_INFO_BSSID nested in 359 * QCA_WLAN_VENDOR_ATTR_BTM_CANDIDATE_INFO in the request. In the response 360 * the driver shall specify array of 361 * QCA_WLAN_VENDOR_ATTR_BTM_CANDIDATE_INFO_BSSID and 362 * QCA_WLAN_VENDOR_ATTR_BTM_CANDIDATE_INFO_STATUS pairs nested in 363 * QCA_WLAN_VENDOR_ATTR_BTM_CANDIDATE_INFO. 364 * 365 * @QCA_NL80211_VENDOR_SUBCMD_SET_TRACE_LEVEL: Set the trace level for a 366 * specific QCA module. The trace levels are represented by 367 * enum qca_attr_trace_level attributes. 368 * 369 * @QCA_NL80211_VENDOR_SUBCMD_BRP_SET_ANT_LIMIT: Set the Beam Refinement 370 * Protocol antenna limit in different modes. See enum 371 * qca_wlan_vendor_attr_brp_ant_limit_mode. 372 * 373 * @QCA_NL80211_VENDOR_SUBCMD_SPECTRAL_SCAN_START: Start spectral scan. The scan 374 * parameters are specified by enum qca_wlan_vendor_attr_spectral_scan. 375 * This returns a cookie (%QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_COOKIE) 376 * identifying the operation in success case. 377 * 378 * @QCA_NL80211_VENDOR_SUBCMD_SPECTRAL_SCAN_STOP: Stop spectral scan. This uses 379 * a cookie (%QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_COOKIE) from 380 * @QCA_NL80211_VENDOR_SUBCMD_SPECTRAL_SCAN_START to identify the scan to 381 * be stopped. 382 * 383 * @QCA_NL80211_VENDOR_SUBCMD_ACTIVE_TOS: Set the active Type Of Service on the 384 * specific interface. This can be used to modify some of the low level 385 * scan parameters (off channel dwell time, home channel time) in the 386 * driver/firmware. These parameters are maintained within the host driver. 387 * This command is valid only when the interface is in the connected state. 388 * These scan parameters shall be reset by the driver/firmware once 389 * disconnected. The attributes used with this command are defined in 390 * enum qca_wlan_vendor_attr_active_tos. 391 * 392 * @QCA_NL80211_VENDOR_SUBCMD_HANG: Event indicating to the user space that the 393 * driver has detected an internal failure. This event carries the 394 * information indicating the reason that triggered this detection. The 395 * attributes for this command are defined in 396 * enum qca_wlan_vendor_attr_hang. 397 * 398 * @QCA_NL80211_VENDOR_SUBCMD_SPECTRAL_SCAN_GET_CONFIG: Get the current values 399 * of spectral parameters used. The spectral scan parameters are specified 400 * by enum qca_wlan_vendor_attr_spectral_scan. 401 * 402 * @QCA_NL80211_VENDOR_SUBCMD_SPECTRAL_SCAN_GET_DIAG_STATS: Get the debug stats 403 * for spectral scan functionality. The debug stats are specified by 404 * enum qca_wlan_vendor_attr_spectral_diag_stats. 405 * 406 * @QCA_NL80211_VENDOR_SUBCMD_SPECTRAL_SCAN_GET_CAP_INFO: Get spectral 407 * scan system capabilities. The capabilities are specified 408 * by enum qca_wlan_vendor_attr_spectral_cap. 409 * 410 * @QCA_NL80211_VENDOR_SUBCMD_SPECTRAL_SCAN_GET_STATUS: Get the current 411 * status of spectral scan. The status values are specified 412 * by enum qca_wlan_vendor_attr_spectral_scan_status. 413 * 414 * @QCA_NL80211_VENDOR_SUBCMD_PEER_FLUSH_PENDING: Sub-command to flush 415 * peer pending packets. Specify the peer MAC address in 416 * QCA_WLAN_VENDOR_ATTR_PEER_ADDR and the access category of the packets 417 * in QCA_WLAN_VENDOR_ATTR_AC. The attributes are listed 418 * in enum qca_wlan_vendor_attr_flush_pending. 419 * 420 * @QCA_NL80211_VENDOR_SUBCMD_GET_RROP_INFO: Get vendor specific Representative 421 * RF Operating Parameter (RROP) information. The attributes for this 422 * information are defined in enum qca_wlan_vendor_attr_rrop_info. This is 423 * intended for use by external Auto Channel Selection applications. 424 * 425 * @QCA_NL80211_VENDOR_SUBCMD_GET_SAR_LIMITS: Get the Specific Absorption Rate 426 * (SAR) power limits. This is a companion to the command 427 * @QCA_NL80211_VENDOR_SUBCMD_SET_SAR_LIMITS and is used to retrieve the 428 * settings currently in use. The attributes returned by this command are 429 * defined by enum qca_vendor_attr_sar_limits. 430 * 431 * @QCA_NL80211_VENDOR_SUBCMD_WLAN_MAC_INFO: Provides the current behavior of 432 * the WLAN hardware MAC. Also, provides the WLAN netdev interface 433 * information attached to the respective MAC. 434 * This works both as a query (user space asks the current mode) or event 435 * interface (driver advertising the current mode to the user space). 436 * Driver does not trigger this event for temporary hardware mode changes. 437 * Mode changes w.r.t Wi-Fi connection update (VIZ creation / deletion, 438 * channel change, etc.) are updated with this event. Attributes for this 439 * interface are defined in enum qca_wlan_vendor_attr_mac. 440 * 441 * @QCA_NL80211_VENDOR_SUBCMD_SET_QDEPTH_THRESH: Set MSDU queue depth threshold 442 * per peer per TID. Attributes for this command are define in 443 * enum qca_wlan_set_qdepth_thresh_attr. 444 * @QCA_NL80211_VENDOR_SUBCMD_THERMAL_CMD: Provides the thermal shutdown action 445 * guide for WLAN driver. Request to suspend of driver and FW if the 446 * temperature is higher than the suspend threshold; resume action is 447 * requested to driver if the temperature is lower than the resume 448 * threshold. In user poll mode, request temperature data by user. For test 449 * purpose, getting thermal shutdown configuration parameters is needed. 450 * Attributes for this interface are defined in 451 * enum qca_wlan_vendor_attr_thermal_cmd. 452 * @QCA_NL80211_VENDOR_SUBCMD_THERMAL_EVENT: Thermal events reported from 453 * driver. Thermal temperature and indication of resume completion are 454 * reported as thermal events. The attributes for this command are defined 455 * in enum qca_wlan_vendor_attr_thermal_event. 456 * 457 * @QCA_NL80211_VENDOR_SUBCMD_WIFI_TEST_CONFIGURATION: Sub command to set WiFi 458 * test configuration. Attributes for this command are defined in 459 * enum qca_wlan_vendor_attr_wifi_test_config. 460 * 461 * @QCA_NL80211_VENDOR_SUBCMD_BSS_FILTER: This command is used to configure an 462 * RX filter to receive frames from stations that are active on the 463 * operating channel, but not associated with the local device (e.g., STAs 464 * associated with other APs). Filtering is done based on a list of BSSIDs 465 * and STA MAC addresses added by the user. This command is also used to 466 * fetch the statistics of unassociated stations. The attributes used with 467 * this command are defined in enum qca_wlan_vendor_attr_bss_filter. 468 * 469 * @QCA_NL80211_VENDOR_SUBCMD_NAN_EXT: An extendable version of NAN vendor 470 * command. The earlier command for NAN, QCA_NL80211_VENDOR_SUBCMD_NAN, 471 * carried a payload which was a binary blob of data. The command was not 472 * extendable to send more information. The newer version carries the 473 * legacy blob encapsulated within an attribute and can be extended with 474 * additional vendor attributes that can enhance the NAN command interface. 475 * @QCA_NL80211_VENDOR_SUBCMD_ROAM_SCAN_EVENT: Event to indicate scan triggered 476 * or stopped within driver/firmware in order to initiate roaming. The 477 * attributes used with this event are defined in enum 478 * qca_wlan_vendor_attr_roam_scan. Some drivers may not send these events 479 * in few cases, e.g., if the host processor is sleeping when this event 480 * is generated in firmware. 481 * 482 * @QCA_NL80211_VENDOR_SUBCMD_PEER_CFR_CAPTURE_CFG: This command is used to 483 * configure parameters per peer to capture Channel Frequency Response 484 * (CFR) and enable Periodic CFR capture. The attributes for this command 485 * are defined in enum qca_wlan_vendor_peer_cfr_capture_attr. 486 * 487 * @QCA_NL80211_VENDOR_SUBCMD_THROUGHPUT_CHANGE_EVENT: Event to indicate changes 488 * in throughput dynamically. The driver estimates the throughput based on 489 * number of packets being transmitted/received per second and indicates 490 * the changes in throughput to user space. Userspace tools can use this 491 * information to configure kernel's TCP parameters in order to achieve 492 * peak throughput. Optionally, the driver will also send guidance on 493 * modifications to kernel's TCP parameters which can be referred by 494 * userspace tools. The attributes used with this event are defined in enum 495 * qca_wlan_vendor_attr_throughput_change. 496 * 497 * @QCA_NL80211_VENDOR_SUBCMD_COEX_CONFIG: This command is used to set 498 * priorities among different types of traffic during coex scenarios. 499 * Current supported prioritization is among WLAN/BT/ZIGBEE with different 500 * profiles mentioned in enum qca_coex_config_profiles. The associated 501 * attributes used with this command are defined in enum 502 * qca_vendor_attr_coex_config. 503 * 504 * Based on the config provided, FW will boost the weight and prioritize 505 * the traffic for that subsystem (WLAN/BT/Zigbee). 506 * 507 * @QCA_NL80211_VENDOR_SUBCMD_GET_SUPPORTED_AKMS: This command is used to query 508 * the supported AKM suite selectorss from the driver. It returns the list 509 * of supported AKMs in the attribute NL80211_ATTR_AKM_SUITES. 510 * @QCA_NL80211_VENDOR_SUBCMD_GET_FW_STATE: This command is used to get firmware 511 * state from the driver. It returns the firmware state in the attribute 512 * QCA_WLAN_VENDOR_ATTR_FW_STATE. 513 * @QCA_NL80211_VENDOR_SUBCMD_PEER_STATS_CACHE_FLUSH: This vendor subcommand 514 * is used by the driver to flush per-peer cached statistics to user space 515 * application. This interface is used as an event from the driver to 516 * user space application. Attributes for this event are specified in 517 * enum qca_wlan_vendor_attr_peer_stats_cache_params. 518 * QCA_WLAN_VENDOR_ATTR_PEER_STATS_CACHE_DATA attribute is expected to be 519 * sent in the event. 520 * @QCA_NL80211_VENDOR_SUBCMD_MPTA_HELPER_CONFIG: This sub command is used to 521 * improve the success rate of Zigbee joining network. 522 * Due to PTA master limitation, Zigbee joining network success rate is 523 * low while WLAN is working. The WLAN driver needs to configure some 524 * parameters including Zigbee state and specific WLAN periods to enhance 525 * PTA master. All these parameters are delivered by the attributes 526 * defined in enum qca_mpta_helper_vendor_attr. 527 */ 528 enum qca_nl80211_vendor_subcmds { 529 QCA_NL80211_VENDOR_SUBCMD_UNSPEC = 0, 530 QCA_NL80211_VENDOR_SUBCMD_TEST = 1, 531 /* subcmds 2..8 not yet allocated */ 532 QCA_NL80211_VENDOR_SUBCMD_ROAMING = 9, 533 QCA_NL80211_VENDOR_SUBCMD_AVOID_FREQUENCY = 10, 534 QCA_NL80211_VENDOR_SUBCMD_DFS_CAPABILITY = 11, 535 QCA_NL80211_VENDOR_SUBCMD_NAN = 12, 536 QCA_NL80211_VENDOR_SUBCMD_STATS_EXT = 13, 537 QCA_NL80211_VENDOR_SUBCMD_LL_STATS_SET = 14, 538 QCA_NL80211_VENDOR_SUBCMD_LL_STATS_GET = 15, 539 QCA_NL80211_VENDOR_SUBCMD_LL_STATS_CLR = 16, 540 QCA_NL80211_VENDOR_SUBCMD_LL_STATS_RADIO_RESULTS = 17, 541 QCA_NL80211_VENDOR_SUBCMD_LL_STATS_IFACE_RESULTS = 18, 542 QCA_NL80211_VENDOR_SUBCMD_LL_STATS_PEERS_RESULTS = 19, 543 QCA_NL80211_VENDOR_SUBCMD_GSCAN_START = 20, 544 QCA_NL80211_VENDOR_SUBCMD_GSCAN_STOP = 21, 545 QCA_NL80211_VENDOR_SUBCMD_GSCAN_GET_VALID_CHANNELS = 22, 546 QCA_NL80211_VENDOR_SUBCMD_GSCAN_GET_CAPABILITIES = 23, 547 QCA_NL80211_VENDOR_SUBCMD_GSCAN_GET_CACHED_RESULTS = 24, 548 QCA_NL80211_VENDOR_SUBCMD_GSCAN_SCAN_RESULTS_AVAILABLE = 25, 549 QCA_NL80211_VENDOR_SUBCMD_GSCAN_FULL_SCAN_RESULT = 26, 550 QCA_NL80211_VENDOR_SUBCMD_GSCAN_SCAN_EVENT = 27, 551 QCA_NL80211_VENDOR_SUBCMD_GSCAN_HOTLIST_AP_FOUND = 28, 552 QCA_NL80211_VENDOR_SUBCMD_GSCAN_SET_BSSID_HOTLIST = 29, 553 QCA_NL80211_VENDOR_SUBCMD_GSCAN_RESET_BSSID_HOTLIST = 30, 554 QCA_NL80211_VENDOR_SUBCMD_GSCAN_SIGNIFICANT_CHANGE = 31, 555 QCA_NL80211_VENDOR_SUBCMD_GSCAN_SET_SIGNIFICANT_CHANGE = 32, 556 QCA_NL80211_VENDOR_SUBCMD_GSCAN_RESET_SIGNIFICANT_CHANGE = 33, 557 QCA_NL80211_VENDOR_SUBCMD_TDLS_ENABLE = 34, 558 QCA_NL80211_VENDOR_SUBCMD_TDLS_DISABLE = 35, 559 QCA_NL80211_VENDOR_SUBCMD_TDLS_GET_STATUS = 36, 560 QCA_NL80211_VENDOR_SUBCMD_TDLS_STATE = 37, 561 QCA_NL80211_VENDOR_SUBCMD_GET_SUPPORTED_FEATURES = 38, 562 QCA_NL80211_VENDOR_SUBCMD_SCANNING_MAC_OUI = 39, 563 QCA_NL80211_VENDOR_SUBCMD_NO_DFS_FLAG = 40, 564 QCA_NL80211_VENDOR_SUBCMD_GSCAN_HOTLIST_AP_LOST = 41, 565 QCA_NL80211_VENDOR_SUBCMD_GET_CONCURRENCY_MATRIX = 42, 566 /* 43..49 - reserved for QCA */ 567 QCA_NL80211_VENDOR_SUBCMD_KEY_MGMT_SET_KEY = 50, 568 QCA_NL80211_VENDOR_SUBCMD_KEY_MGMT_ROAM_AUTH = 51, 569 QCA_NL80211_VENDOR_SUBCMD_APFIND = 52, 570 /* 53 - reserved - was used by QCA, but not in use anymore */ 571 QCA_NL80211_VENDOR_SUBCMD_DO_ACS = 54, 572 QCA_NL80211_VENDOR_SUBCMD_GET_FEATURES = 55, 573 QCA_NL80211_VENDOR_SUBCMD_DFS_OFFLOAD_CAC_STARTED = 56, 574 QCA_NL80211_VENDOR_SUBCMD_DFS_OFFLOAD_CAC_FINISHED = 57, 575 QCA_NL80211_VENDOR_SUBCMD_DFS_OFFLOAD_CAC_ABORTED = 58, 576 QCA_NL80211_VENDOR_SUBCMD_DFS_OFFLOAD_CAC_NOP_FINISHED = 59, 577 QCA_NL80211_VENDOR_SUBCMD_DFS_OFFLOAD_RADAR_DETECTED = 60, 578 QCA_NL80211_VENDOR_SUBCMD_GET_WIFI_INFO = 61, 579 QCA_NL80211_VENDOR_SUBCMD_WIFI_LOGGER_START = 62, 580 QCA_NL80211_VENDOR_SUBCMD_WIFI_LOGGER_MEMORY_DUMP = 63, 581 QCA_NL80211_VENDOR_SUBCMD_ROAM = 64, 582 QCA_NL80211_VENDOR_SUBCMD_GSCAN_SET_SSID_HOTLIST = 65, 583 QCA_NL80211_VENDOR_SUBCMD_GSCAN_RESET_SSID_HOTLIST = 66, 584 QCA_NL80211_VENDOR_SUBCMD_GSCAN_HOTLIST_SSID_FOUND = 67, 585 QCA_NL80211_VENDOR_SUBCMD_GSCAN_HOTLIST_SSID_LOST = 68, 586 QCA_NL80211_VENDOR_SUBCMD_PNO_SET_LIST = 69, 587 QCA_NL80211_VENDOR_SUBCMD_PNO_SET_PASSPOINT_LIST = 70, 588 QCA_NL80211_VENDOR_SUBCMD_PNO_RESET_PASSPOINT_LIST = 71, 589 QCA_NL80211_VENDOR_SUBCMD_PNO_NETWORK_FOUND = 72, 590 QCA_NL80211_VENDOR_SUBCMD_PNO_PASSPOINT_NETWORK_FOUND = 73, 591 /* Wi-Fi configuration subcommands */ 592 QCA_NL80211_VENDOR_SUBCMD_SET_WIFI_CONFIGURATION = 74, 593 QCA_NL80211_VENDOR_SUBCMD_GET_WIFI_CONFIGURATION = 75, 594 QCA_NL80211_VENDOR_SUBCMD_GET_LOGGER_FEATURE_SET = 76, 595 QCA_NL80211_VENDOR_SUBCMD_GET_RING_DATA = 77, 596 QCA_NL80211_VENDOR_SUBCMD_TDLS_GET_CAPABILITIES = 78, 597 QCA_NL80211_VENDOR_SUBCMD_OFFLOADED_PACKETS = 79, 598 QCA_NL80211_VENDOR_SUBCMD_MONITOR_RSSI = 80, 599 QCA_NL80211_VENDOR_SUBCMD_NDP = 81, 600 QCA_NL80211_VENDOR_SUBCMD_ND_OFFLOAD = 82, 601 QCA_NL80211_VENDOR_SUBCMD_PACKET_FILTER = 83, 602 QCA_NL80211_VENDOR_SUBCMD_GET_BUS_SIZE = 84, 603 QCA_NL80211_VENDOR_SUBCMD_GET_WAKE_REASON_STATS = 85, 604 /* 86-90 - reserved for QCA */ 605 QCA_NL80211_VENDOR_SUBCMD_DATA_OFFLOAD = 91, 606 QCA_NL80211_VENDOR_SUBCMD_OCB_SET_CONFIG = 92, 607 QCA_NL80211_VENDOR_SUBCMD_OCB_SET_UTC_TIME = 93, 608 QCA_NL80211_VENDOR_SUBCMD_OCB_START_TIMING_ADVERT = 94, 609 QCA_NL80211_VENDOR_SUBCMD_OCB_STOP_TIMING_ADVERT = 95, 610 QCA_NL80211_VENDOR_SUBCMD_OCB_GET_TSF_TIMER = 96, 611 QCA_NL80211_VENDOR_SUBCMD_DCC_GET_STATS = 97, 612 QCA_NL80211_VENDOR_SUBCMD_DCC_CLEAR_STATS = 98, 613 QCA_NL80211_VENDOR_SUBCMD_DCC_UPDATE_NDL = 99, 614 QCA_NL80211_VENDOR_SUBCMD_DCC_STATS_EVENT = 100, 615 QCA_NL80211_VENDOR_SUBCMD_LINK_PROPERTIES = 101, 616 QCA_NL80211_VENDOR_SUBCMD_GW_PARAM_CONFIG = 102, 617 QCA_NL80211_VENDOR_SUBCMD_GET_PREFERRED_FREQ_LIST = 103, 618 QCA_NL80211_VENDOR_SUBCMD_SET_PROBABLE_OPER_CHANNEL = 104, 619 QCA_NL80211_VENDOR_SUBCMD_SETBAND = 105, 620 QCA_NL80211_VENDOR_SUBCMD_TRIGGER_SCAN = 106, 621 QCA_NL80211_VENDOR_SUBCMD_SCAN_DONE = 107, 622 QCA_NL80211_VENDOR_SUBCMD_OTA_TEST = 108, 623 QCA_NL80211_VENDOR_SUBCMD_SET_TXPOWER_SCALE = 109, 624 /* 110..114 - reserved for QCA */ 625 QCA_NL80211_VENDOR_SUBCMD_SET_TXPOWER_DECR_DB = 115, 626 /* 116..117 - reserved for QCA */ 627 QCA_NL80211_VENDOR_SUBCMD_SET_SAP_CONFIG = 118, 628 QCA_NL80211_VENDOR_SUBCMD_TSF = 119, 629 QCA_NL80211_VENDOR_SUBCMD_WISA = 120, 630 /* 121 - reserved for QCA */ 631 QCA_NL80211_VENDOR_SUBCMD_P2P_LISTEN_OFFLOAD_START = 122, 632 QCA_NL80211_VENDOR_SUBCMD_P2P_LISTEN_OFFLOAD_STOP = 123, 633 QCA_NL80211_VENDOR_SUBCMD_SAP_CONDITIONAL_CHAN_SWITCH = 124, 634 QCA_NL80211_VENDOR_SUBCMD_GPIO_CONFIG_COMMAND = 125, 635 QCA_NL80211_VENDOR_SUBCMD_GET_HW_CAPABILITY = 126, 636 QCA_NL80211_VENDOR_SUBCMD_LL_STATS_EXT = 127, 637 /* FTM/indoor location subcommands */ 638 QCA_NL80211_VENDOR_SUBCMD_LOC_GET_CAPA = 128, 639 QCA_NL80211_VENDOR_SUBCMD_FTM_START_SESSION = 129, 640 QCA_NL80211_VENDOR_SUBCMD_FTM_ABORT_SESSION = 130, 641 QCA_NL80211_VENDOR_SUBCMD_FTM_MEAS_RESULT = 131, 642 QCA_NL80211_VENDOR_SUBCMD_FTM_SESSION_DONE = 132, 643 QCA_NL80211_VENDOR_SUBCMD_FTM_CFG_RESPONDER = 133, 644 QCA_NL80211_VENDOR_SUBCMD_AOA_MEAS = 134, 645 QCA_NL80211_VENDOR_SUBCMD_AOA_ABORT_MEAS = 135, 646 QCA_NL80211_VENDOR_SUBCMD_AOA_MEAS_RESULT = 136, 647 QCA_NL80211_VENDOR_SUBCMD_ENCRYPTION_TEST = 137, 648 QCA_NL80211_VENDOR_SUBCMD_GET_CHAIN_RSSI = 138, 649 /* DMG low level RF sector operations */ 650 QCA_NL80211_VENDOR_SUBCMD_DMG_RF_GET_SECTOR_CFG = 139, 651 QCA_NL80211_VENDOR_SUBCMD_DMG_RF_SET_SECTOR_CFG = 140, 652 QCA_NL80211_VENDOR_SUBCMD_DMG_RF_GET_SELECTED_SECTOR = 141, 653 QCA_NL80211_VENDOR_SUBCMD_DMG_RF_SET_SELECTED_SECTOR = 142, 654 QCA_NL80211_VENDOR_SUBCMD_CONFIGURE_TDLS = 143, 655 QCA_NL80211_VENDOR_SUBCMD_GET_HE_CAPABILITIES = 144, 656 QCA_NL80211_VENDOR_SUBCMD_ABORT_SCAN = 145, 657 QCA_NL80211_VENDOR_SUBCMD_SET_SAR_LIMITS = 146, 658 QCA_NL80211_VENDOR_SUBCMD_EXTERNAL_ACS = 147, 659 QCA_NL80211_VENDOR_SUBCMD_CHIP_PWRSAVE_FAILURE = 148, 660 QCA_NL80211_VENDOR_SUBCMD_NUD_STATS_SET = 149, 661 QCA_NL80211_VENDOR_SUBCMD_NUD_STATS_GET = 150, 662 QCA_NL80211_VENDOR_SUBCMD_FETCH_BSS_TRANSITION_STATUS = 151, 663 QCA_NL80211_VENDOR_SUBCMD_SET_TRACE_LEVEL = 152, 664 QCA_NL80211_VENDOR_SUBCMD_BRP_SET_ANT_LIMIT = 153, 665 QCA_NL80211_VENDOR_SUBCMD_SPECTRAL_SCAN_START = 154, 666 QCA_NL80211_VENDOR_SUBCMD_SPECTRAL_SCAN_STOP = 155, 667 QCA_NL80211_VENDOR_SUBCMD_ACTIVE_TOS = 156, 668 QCA_NL80211_VENDOR_SUBCMD_HANG = 157, 669 QCA_NL80211_VENDOR_SUBCMD_SPECTRAL_SCAN_GET_CONFIG = 158, 670 QCA_NL80211_VENDOR_SUBCMD_SPECTRAL_SCAN_GET_DIAG_STATS = 159, 671 QCA_NL80211_VENDOR_SUBCMD_SPECTRAL_SCAN_GET_CAP_INFO = 160, 672 QCA_NL80211_VENDOR_SUBCMD_SPECTRAL_SCAN_GET_STATUS = 161, 673 /* Flush peer pending data */ 674 QCA_NL80211_VENDOR_SUBCMD_PEER_FLUSH_PENDING = 162, 675 QCA_NL80211_VENDOR_SUBCMD_GET_RROP_INFO = 163, 676 QCA_NL80211_VENDOR_SUBCMD_GET_SAR_LIMITS = 164, 677 QCA_NL80211_VENDOR_SUBCMD_WLAN_MAC_INFO = 165, 678 QCA_NL80211_VENDOR_SUBCMD_SET_QDEPTH_THRESH = 166, 679 /* Thermal shutdown commands to protect wifi chip */ 680 QCA_NL80211_VENDOR_SUBCMD_THERMAL_CMD = 167, 681 QCA_NL80211_VENDOR_SUBCMD_THERMAL_EVENT = 168, 682 /* Wi-Fi test configuration subcommand */ 683 QCA_NL80211_VENDOR_SUBCMD_WIFI_TEST_CONFIGURATION = 169, 684 /* Frame filter operations for other BSSs/unassociated STAs */ 685 QCA_NL80211_VENDOR_SUBCMD_BSS_FILTER = 170, 686 QCA_NL80211_VENDOR_SUBCMD_NAN_EXT = 171, 687 QCA_NL80211_VENDOR_SUBCMD_ROAM_SCAN_EVENT = 172, 688 QCA_NL80211_VENDOR_SUBCMD_PEER_CFR_CAPTURE_CFG = 173, 689 QCA_NL80211_VENDOR_SUBCMD_THROUGHPUT_CHANGE_EVENT = 174, 690 QCA_NL80211_VENDOR_SUBCMD_COEX_CONFIG = 175, 691 QCA_NL80211_VENDOR_SUBCMD_GET_SUPPORTED_AKMS = 176, 692 QCA_NL80211_VENDOR_SUBCMD_GET_FW_STATE = 177, 693 QCA_NL80211_VENDOR_SUBCMD_PEER_STATS_CACHE_FLUSH = 178, 694 QCA_NL80211_VENDOR_SUBCMD_MPTA_HELPER_CONFIG = 179, 695 }; 696 697 enum qca_wlan_vendor_attr { 698 QCA_WLAN_VENDOR_ATTR_INVALID = 0, 699 /* used by QCA_NL80211_VENDOR_SUBCMD_DFS_CAPABILITY */ 700 QCA_WLAN_VENDOR_ATTR_DFS = 1, 701 /* Used only when driver sends vendor events to the userspace under the 702 * command QCA_NL80211_VENDOR_SUBCMD_NAN. Not used when userspace sends 703 * commands to the driver. 704 */ 705 QCA_WLAN_VENDOR_ATTR_NAN = 2, 706 /* used by QCA_NL80211_VENDOR_SUBCMD_STATS_EXT */ 707 QCA_WLAN_VENDOR_ATTR_STATS_EXT = 3, 708 /* used by QCA_NL80211_VENDOR_SUBCMD_STATS_EXT */ 709 QCA_WLAN_VENDOR_ATTR_IFINDEX = 4, 710 /* used by QCA_NL80211_VENDOR_SUBCMD_ROAMING, u32 with values defined 711 * by enum qca_roaming_policy. 712 */ 713 QCA_WLAN_VENDOR_ATTR_ROAMING_POLICY = 5, 714 QCA_WLAN_VENDOR_ATTR_MAC_ADDR = 6, 715 /* used by QCA_NL80211_VENDOR_SUBCMD_GET_FEATURES */ 716 QCA_WLAN_VENDOR_ATTR_FEATURE_FLAGS = 7, 717 QCA_WLAN_VENDOR_ATTR_TEST = 8, 718 /* used by QCA_NL80211_VENDOR_SUBCMD_GET_FEATURES */ 719 /* Unsigned 32-bit value. */ 720 QCA_WLAN_VENDOR_ATTR_CONCURRENCY_CAPA = 9, 721 /* Unsigned 32-bit value */ 722 QCA_WLAN_VENDOR_ATTR_MAX_CONCURRENT_CHANNELS_2_4_BAND = 10, 723 /* Unsigned 32-bit value */ 724 QCA_WLAN_VENDOR_ATTR_MAX_CONCURRENT_CHANNELS_5_0_BAND = 11, 725 /* Unsigned 32-bit value from enum qca_set_band. */ 726 QCA_WLAN_VENDOR_ATTR_SETBAND_VALUE = 12, 727 /* Dummy (NOP) attribute for 64 bit padding */ 728 QCA_WLAN_VENDOR_ATTR_PAD = 13, 729 /* Unique FTM session cookie (Unsigned 64 bit). Specified in 730 * QCA_NL80211_VENDOR_SUBCMD_FTM_START_SESSION. Reported in 731 * the session in QCA_NL80211_VENDOR_SUBCMD_FTM_MEAS_RESULT and 732 * QCA_NL80211_VENDOR_SUBCMD_FTM_SESSION_DONE. 733 */ 734 QCA_WLAN_VENDOR_ATTR_FTM_SESSION_COOKIE = 14, 735 /* Indoor location capabilities, returned by 736 * QCA_NL80211_VENDOR_SUBCMD_LOC_GET_CAPA. 737 * see enum qca_wlan_vendor_attr_loc_capa. 738 */ 739 QCA_WLAN_VENDOR_ATTR_LOC_CAPA = 15, 740 /* Array of nested attributes containing information about each peer 741 * in FTM measurement session. See enum qca_wlan_vendor_attr_peer_info 742 * for supported attributes for each peer. 743 */ 744 QCA_WLAN_VENDOR_ATTR_FTM_MEAS_PEERS = 16, 745 /* Array of nested attributes containing measurement results for 746 * one or more peers, reported by the 747 * QCA_NL80211_VENDOR_SUBCMD_FTM_MEAS_RESULT event. 748 * See enum qca_wlan_vendor_attr_peer_result for list of supported 749 * attributes. 750 */ 751 QCA_WLAN_VENDOR_ATTR_FTM_MEAS_PEER_RESULTS = 17, 752 /* Flag attribute for enabling or disabling responder functionality. */ 753 QCA_WLAN_VENDOR_ATTR_FTM_RESPONDER_ENABLE = 18, 754 /* Used in the QCA_NL80211_VENDOR_SUBCMD_FTM_CFG_RESPONDER 755 * command to specify the LCI report that will be sent by 756 * the responder during a measurement exchange. The format is 757 * defined in IEEE P802.11-REVmc/D7.0, 9.4.2.22.10. 758 */ 759 QCA_WLAN_VENDOR_ATTR_FTM_LCI = 19, 760 /* Used in the QCA_NL80211_VENDOR_SUBCMD_FTM_CFG_RESPONDER 761 * command to specify the location civic report that will 762 * be sent by the responder during a measurement exchange. 763 * The format is defined in IEEE P802.11-REVmc/D7.0, 9.4.2.22.13. 764 */ 765 QCA_WLAN_VENDOR_ATTR_FTM_LCR = 20, 766 /* Session/measurement completion status code, 767 * reported in QCA_NL80211_VENDOR_SUBCMD_FTM_SESSION_DONE and 768 * QCA_NL80211_VENDOR_SUBCMD_AOA_MEAS_RESULT 769 * see enum qca_vendor_attr_loc_session_status. 770 */ 771 QCA_WLAN_VENDOR_ATTR_LOC_SESSION_STATUS = 21, 772 /* Initial dialog token used by responder (0 if not specified), 773 * unsigned 8 bit value. 774 */ 775 QCA_WLAN_VENDOR_ATTR_FTM_INITIAL_TOKEN = 22, 776 /* AOA measurement type. Requested in QCA_NL80211_VENDOR_SUBCMD_AOA_MEAS 777 * and optionally in QCA_NL80211_VENDOR_SUBCMD_FTM_START_SESSION if 778 * AOA measurements are needed as part of an FTM session. 779 * Reported by QCA_NL80211_VENDOR_SUBCMD_AOA_MEAS_RESULT. See 780 * enum qca_wlan_vendor_attr_aoa_type. 781 */ 782 QCA_WLAN_VENDOR_ATTR_AOA_TYPE = 23, 783 /* A bit mask (unsigned 32 bit value) of antenna arrays used 784 * by indoor location measurements. Refers to the antenna 785 * arrays described by QCA_VENDOR_ATTR_LOC_CAPA_ANTENNA_ARRAYS. 786 */ 787 QCA_WLAN_VENDOR_ATTR_LOC_ANTENNA_ARRAY_MASK = 24, 788 /* AOA measurement data. Its contents depends on the AOA measurement 789 * type and antenna array mask: 790 * QCA_WLAN_VENDOR_ATTR_AOA_TYPE_TOP_CIR_PHASE: array of U16 values, 791 * phase of the strongest CIR path for each antenna in the measured 792 * array(s). 793 * QCA_WLAN_VENDOR_ATTR_AOA_TYPE_TOP_CIR_PHASE_AMP: array of 2 U16 794 * values, phase and amplitude of the strongest CIR path for each 795 * antenna in the measured array(s). 796 */ 797 QCA_WLAN_VENDOR_ATTR_AOA_MEAS_RESULT = 25, 798 /* Used in QCA_NL80211_VENDOR_SUBCMD_GET_CHAIN_RSSI command 799 * to specify the chain number (unsigned 32 bit value) to inquire 800 * the corresponding antenna RSSI value 801 */ 802 QCA_WLAN_VENDOR_ATTR_CHAIN_INDEX = 26, 803 /* Used in QCA_NL80211_VENDOR_SUBCMD_GET_CHAIN_RSSI command 804 * to report the specific antenna RSSI value (unsigned 32 bit value) 805 */ 806 QCA_WLAN_VENDOR_ATTR_CHAIN_RSSI = 27, 807 /* Frequency in MHz, various uses. Unsigned 32 bit value */ 808 QCA_WLAN_VENDOR_ATTR_FREQ = 28, 809 /* TSF timer value, unsigned 64 bit value. 810 * May be returned by various commands. 811 */ 812 QCA_WLAN_VENDOR_ATTR_TSF = 29, 813 /* DMG RF sector index, unsigned 16 bit number. Valid values are 814 * 0..127 for sector indices or 65535 as special value used to 815 * unlock sector selection in 816 * QCA_NL80211_VENDOR_SUBCMD_DMG_RF_SET_SELECTED_SECTOR. 817 */ 818 QCA_WLAN_VENDOR_ATTR_DMG_RF_SECTOR_INDEX = 30, 819 /* DMG RF sector type, unsigned 8 bit value. One of the values 820 * in enum qca_wlan_vendor_attr_dmg_rf_sector_type. 821 */ 822 QCA_WLAN_VENDOR_ATTR_DMG_RF_SECTOR_TYPE = 31, 823 /* Bitmask of DMG RF modules for which information is requested. Each 824 * bit corresponds to an RF module with the same index as the bit 825 * number. Unsigned 32 bit number but only low 8 bits can be set since 826 * all DMG chips currently have up to 8 RF modules. 827 */ 828 QCA_WLAN_VENDOR_ATTR_DMG_RF_MODULE_MASK = 32, 829 /* Array of nested attributes where each entry is DMG RF sector 830 * configuration for a single RF module. 831 * Attributes for each entry are taken from enum 832 * qca_wlan_vendor_attr_dmg_rf_sector_cfg. 833 * Specified in QCA_NL80211_VENDOR_SUBCMD_DMG_RF_SET_SECTOR_CFG 834 * and returned by QCA_NL80211_VENDOR_SUBCMD_DMG_RF_GET_SECTOR_CFG. 835 */ 836 QCA_WLAN_VENDOR_ATTR_DMG_RF_SECTOR_CFG = 33, 837 /* Used in QCA_NL80211_VENDOR_SUBCMD_STATS_EXT command 838 * to report frame aggregation statistics to userspace. 839 */ 840 QCA_WLAN_VENDOR_ATTR_RX_AGGREGATION_STATS_HOLES_NUM = 34, 841 QCA_WLAN_VENDOR_ATTR_RX_AGGREGATION_STATS_HOLES_INFO = 35, 842 /* Unsigned 8-bit value representing MBO transition reason code as 843 * provided by the AP used by subcommand 844 * QCA_NL80211_VENDOR_SUBCMD_FETCH_BSS_TRANSITION_STATUS. This is 845 * specified by the userspace in the request to the driver. 846 */ 847 QCA_WLAN_VENDOR_ATTR_BTM_MBO_TRANSITION_REASON = 36, 848 /* Array of nested attributes, BSSID and status code, used by subcommand 849 * QCA_NL80211_VENDOR_SUBCMD_FETCH_BSS_TRANSITION_STATUS, where each 850 * entry is taken from enum qca_wlan_vendor_attr_btm_candidate_info. 851 * The userspace space specifies the list/array of candidate BSSIDs in 852 * the order of preference in the request. The driver specifies the 853 * status code, for each BSSID in the list, in the response. The 854 * acceptable candidates are listed in the order preferred by the 855 * driver. 856 */ 857 QCA_WLAN_VENDOR_ATTR_BTM_CANDIDATE_INFO = 37, 858 /* Used in QCA_NL80211_VENDOR_SUBCMD_BRP_SET_ANT_LIMIT command 859 * See enum qca_wlan_vendor_attr_brp_ant_limit_mode. 860 */ 861 QCA_WLAN_VENDOR_ATTR_BRP_ANT_LIMIT_MODE = 38, 862 /* Used in QCA_NL80211_VENDOR_SUBCMD_BRP_SET_ANT_LIMIT command 863 * to define the number of antennas to use for BRP. 864 * different purpose in each ANT_LIMIT_MODE: 865 * DISABLE - ignored 866 * EFFECTIVE - upper limit to number of antennas to be used 867 * FORCE - exact number of antennas to be used 868 * unsigned 8 bit value 869 */ 870 QCA_WLAN_VENDOR_ATTR_BRP_ANT_NUM_LIMIT = 39, 871 /* Used in QCA_NL80211_VENDOR_SUBCMD_GET_CHAIN_RSSI command 872 * to report the corresponding antenna index to the chain RSSI value 873 */ 874 QCA_WLAN_VENDOR_ATTR_ANTENNA_INFO = 40, 875 /* Used in QCA_NL80211_VENDOR_SUBCMD_GET_CHAIN_RSSI command to report 876 * the specific antenna EVM value (unsigned 32 bit value). With a 877 * determinate group of antennas, the driver specifies the EVM value 878 * for each antenna ID, and application extract them in user space. 879 */ 880 QCA_WLAN_VENDOR_ATTR_CHAIN_EVM = 41, 881 /* 882 * Used in QCA_NL80211_VENDOR_SUBCMD_GET_FW_STATE command to report 883 * wlan firmware current state. FW state is an unsigned 8 bit value, 884 * one of the values in enum qca_wlan_vendor_attr_fw_state. 885 */ 886 QCA_WLAN_VENDOR_ATTR_FW_STATE = 42, 887 888 /* keep last */ 889 QCA_WLAN_VENDOR_ATTR_AFTER_LAST, 890 QCA_WLAN_VENDOR_ATTR_MAX = QCA_WLAN_VENDOR_ATTR_AFTER_LAST - 1, 891 }; 892 893 enum qca_roaming_policy { 894 QCA_ROAMING_NOT_ALLOWED, 895 QCA_ROAMING_ALLOWED_WITHIN_ESS, 896 }; 897 898 /** 899 * enum qca_roam_reason - Represents the reason codes for roaming. Used by 900 * QCA_WLAN_VENDOR_ATTR_ROAM_AUTH_REASON. 901 * 902 * @QCA_ROAM_REASON_UNKNOWN: Any reason that do not classify under the below 903 * reasons. 904 * 905 * @QCA_ROAM_REASON_PER: Roam triggered when packet error rates (PER) breached 906 * the configured threshold. 907 * 908 * @QCA_ROAM_REASON_BEACON_MISS: Roam triggered due to the continuous configured 909 * beacon misses from the then connected AP. 910 * 911 * @QCA_ROAM_REASON_POOR_RSSI: Roam triggered due to the poor RSSI reported 912 * by the connected AP. 913 * 914 * @QCA_ROAM_REASON_BETTER_RSSI: Roam triggered for finding a BSS with a better 915 * RSSI than the connected BSS. Here the RSSI of the current BSS is not poor. 916 * 917 * @QCA_ROAM_REASON_CONGESTION: Roam triggered considering the connected channel 918 * or environment being very noisy or congested. 919 * 920 * @QCA_ROAM_REASON_EXPLICIT_REQUEST: Roam triggered due to an explicit request 921 * from the user (user space). 922 * 923 * @QCA_ROAM_REASON_BTM: Roam triggered due to BTM Request frame received from 924 * the connected AP. 925 * 926 * @QCA_ROAM_REASON_BSS_LOAD: Roam triggered due to the channel utilization 927 * breaching out the configured threshold. 928 */ 929 enum qca_roam_reason { 930 QCA_ROAM_REASON_UNKNOWN, 931 QCA_ROAM_REASON_PER, 932 QCA_ROAM_REASON_BEACON_MISS, 933 QCA_ROAM_REASON_POOR_RSSI, 934 QCA_ROAM_REASON_BETTER_RSSI, 935 QCA_ROAM_REASON_CONGESTION, 936 QCA_ROAM_REASON_USER_TRIGGER, 937 QCA_ROAM_REASON_BTM, 938 QCA_ROAM_REASON_BSS_LOAD, 939 }; 940 941 enum qca_wlan_vendor_attr_roam_auth { 942 QCA_WLAN_VENDOR_ATTR_ROAM_AUTH_INVALID = 0, 943 QCA_WLAN_VENDOR_ATTR_ROAM_AUTH_BSSID, 944 QCA_WLAN_VENDOR_ATTR_ROAM_AUTH_REQ_IE, 945 QCA_WLAN_VENDOR_ATTR_ROAM_AUTH_RESP_IE, 946 QCA_WLAN_VENDOR_ATTR_ROAM_AUTH_AUTHORIZED, 947 QCA_WLAN_VENDOR_ATTR_ROAM_AUTH_KEY_REPLAY_CTR, 948 QCA_WLAN_VENDOR_ATTR_ROAM_AUTH_PTK_KCK, 949 QCA_WLAN_VENDOR_ATTR_ROAM_AUTH_PTK_KEK, 950 QCA_WLAN_VENDOR_ATTR_ROAM_AUTH_SUBNET_STATUS, 951 /* Indicates the status of re-association requested by user space for 952 * the BSSID specified by QCA_WLAN_VENDOR_ATTR_ROAM_AUTH_BSSID. 953 * Type u16. 954 * Represents the status code from AP. Use 955 * %WLAN_STATUS_UNSPECIFIED_FAILURE if the device cannot give you the 956 * real status code for failures. 957 */ 958 QCA_WLAN_VENDOR_ATTR_ROAM_AUTH_STATUS, 959 /* This attribute indicates that the old association was maintained when 960 * a re-association is requested by user space and that re-association 961 * attempt fails (i.e., cannot connect to the requested BSS, but can 962 * remain associated with the BSS with which the association was in 963 * place when being requested to roam). Used along with 964 * WLAN_VENDOR_ATTR_ROAM_AUTH_STATUS to indicate the current 965 * re-association status. Type flag. 966 * This attribute is applicable only for re-association failure cases. 967 */ 968 QCA_WLAN_VENDOR_ATTR_ROAM_AUTH_RETAIN_CONNECTION, 969 /* This attribute specifies the PMK if one was newly generated during 970 * FILS roaming. This is added to the PMKSA cache and is used in 971 * subsequent connections with PMKSA caching. 972 */ 973 QCA_WLAN_VENDOR_ATTR_ROAM_AUTH_PMK = 11, 974 /* This attribute specifies the PMKID used/generated for the current 975 * FILS roam. This is used in subsequent connections with PMKSA caching. 976 */ 977 QCA_WLAN_VENDOR_ATTR_ROAM_AUTH_PMKID = 12, 978 /* A 16-bit unsigned value specifying the next sequence number to use 979 * in ERP message in the currently associated realm. This is used in 980 * doing subsequent ERP based connections in the same realm. 981 */ 982 QCA_WLAN_VENDOR_ATTR_ROAM_AUTH_FILS_ERP_NEXT_SEQ_NUM = 13, 983 /* A 16-bit unsigned value representing the reasons for the roaming. 984 * Defined by enum qca_roam_reason. 985 */ 986 QCA_WLAN_VENDOR_ATTR_ROAM_AUTH_REASON = 14, 987 988 /* keep last */ 989 QCA_WLAN_VENDOR_ATTR_ROAM_AUTH_AFTER_LAST, 990 QCA_WLAN_VENDOR_ATTR_ROAM_AUTH_MAX = 991 QCA_WLAN_VENDOR_ATTR_ROAM_AUTH_AFTER_LAST - 1 992 }; 993 994 enum qca_wlan_vendor_attr_p2p_listen_offload { 995 QCA_WLAN_VENDOR_ATTR_P2P_LISTEN_OFFLOAD_INVALID = 0, 996 /* A 32-bit unsigned value; the P2P listen frequency (MHz); must be one 997 * of the social channels. 998 */ 999 QCA_WLAN_VENDOR_ATTR_P2P_LISTEN_OFFLOAD_CHANNEL, 1000 /* A 32-bit unsigned value; the P2P listen offload period (ms). 1001 */ 1002 QCA_WLAN_VENDOR_ATTR_P2P_LISTEN_OFFLOAD_PERIOD, 1003 /* A 32-bit unsigned value; the P2P listen interval duration (ms). 1004 */ 1005 QCA_WLAN_VENDOR_ATTR_P2P_LISTEN_OFFLOAD_INTERVAL, 1006 /* A 32-bit unsigned value; number of interval times the firmware needs 1007 * to run the offloaded P2P listen operation before it stops. 1008 */ 1009 QCA_WLAN_VENDOR_ATTR_P2P_LISTEN_OFFLOAD_COUNT, 1010 /* An array of arbitrary binary data with one or more 8-byte values. 1011 * The device types include both primary and secondary device types. 1012 */ 1013 QCA_WLAN_VENDOR_ATTR_P2P_LISTEN_OFFLOAD_DEVICE_TYPES, 1014 /* An array of unsigned 8-bit characters; vendor information elements. 1015 */ 1016 QCA_WLAN_VENDOR_ATTR_P2P_LISTEN_OFFLOAD_VENDOR_IE, 1017 /* A 32-bit unsigned value; a control flag to indicate whether listen 1018 * results need to be flushed to wpa_supplicant. 1019 */ 1020 QCA_WLAN_VENDOR_ATTR_P2P_LISTEN_OFFLOAD_CTRL_FLAG, 1021 /* A 8-bit unsigned value; reason code for P2P listen offload stop 1022 * event. 1023 */ 1024 QCA_WLAN_VENDOR_ATTR_P2P_LISTEN_OFFLOAD_STOP_REASON, 1025 /* keep last */ 1026 QCA_WLAN_VENDOR_ATTR_P2P_LISTEN_OFFLOAD_AFTER_LAST, 1027 QCA_WLAN_VENDOR_ATTR_P2P_LISTEN_OFFLOAD_MAX = 1028 QCA_WLAN_VENDOR_ATTR_P2P_LISTEN_OFFLOAD_AFTER_LAST - 1 1029 }; 1030 1031 enum qca_wlan_vendor_attr_acs_offload { 1032 QCA_WLAN_VENDOR_ATTR_ACS_CHANNEL_INVALID = 0, 1033 QCA_WLAN_VENDOR_ATTR_ACS_PRIMARY_CHANNEL, 1034 QCA_WLAN_VENDOR_ATTR_ACS_SECONDARY_CHANNEL, 1035 QCA_WLAN_VENDOR_ATTR_ACS_HW_MODE, 1036 QCA_WLAN_VENDOR_ATTR_ACS_HT_ENABLED, 1037 QCA_WLAN_VENDOR_ATTR_ACS_HT40_ENABLED, 1038 QCA_WLAN_VENDOR_ATTR_ACS_VHT_ENABLED, 1039 QCA_WLAN_VENDOR_ATTR_ACS_CHWIDTH, 1040 QCA_WLAN_VENDOR_ATTR_ACS_CH_LIST, 1041 QCA_WLAN_VENDOR_ATTR_ACS_VHT_SEG0_CENTER_CHANNEL, 1042 QCA_WLAN_VENDOR_ATTR_ACS_VHT_SEG1_CENTER_CHANNEL, 1043 QCA_WLAN_VENDOR_ATTR_ACS_FREQ_LIST, 1044 /* keep last */ 1045 QCA_WLAN_VENDOR_ATTR_ACS_AFTER_LAST, 1046 QCA_WLAN_VENDOR_ATTR_ACS_MAX = 1047 QCA_WLAN_VENDOR_ATTR_ACS_AFTER_LAST - 1 1048 }; 1049 1050 enum qca_wlan_vendor_acs_hw_mode { 1051 QCA_ACS_MODE_IEEE80211B, 1052 QCA_ACS_MODE_IEEE80211G, 1053 QCA_ACS_MODE_IEEE80211A, 1054 QCA_ACS_MODE_IEEE80211AD, 1055 QCA_ACS_MODE_IEEE80211ANY, 1056 }; 1057 1058 /** 1059 * enum qca_wlan_vendor_features - Vendor device/driver feature flags 1060 * 1061 * @QCA_WLAN_VENDOR_FEATURE_KEY_MGMT_OFFLOAD: Device supports key 1062 * management offload, a mechanism where the station's firmware 1063 * does the exchange with the AP to establish the temporal keys 1064 * after roaming, rather than having the user space wpa_supplicant do it. 1065 * @QCA_WLAN_VENDOR_FEATURE_SUPPORT_HW_MODE_ANY: Device supports automatic 1066 * band selection based on channel selection results. 1067 * @QCA_WLAN_VENDOR_FEATURE_OFFCHANNEL_SIMULTANEOUS: Device supports 1068 * simultaneous off-channel operations. 1069 * @QCA_WLAN_VENDOR_FEATURE_P2P_LISTEN_OFFLOAD: Device supports P2P 1070 * Listen offload; a mechanism where the station's firmware takes care of 1071 * responding to incoming Probe Request frames received from other P2P 1072 * Devices whilst in Listen state, rather than having the user space 1073 * wpa_supplicant do it. Information from received P2P requests are 1074 * forwarded from firmware to host whenever the host processor wakes up. 1075 * @QCA_WLAN_VENDOR_FEATURE_OCE_STA: Device supports all OCE non-AP STA 1076 * specific features. 1077 * @QCA_WLAN_VENDOR_FEATURE_OCE_AP: Device supports all OCE AP specific 1078 * features. 1079 * @QCA_WLAN_VENDOR_FEATURE_OCE_STA_CFON: Device supports OCE STA-CFON 1080 * specific features only. If a Device sets this bit but not the 1081 * %QCA_WLAN_VENDOR_FEATURE_OCE_AP, the userspace shall assume that 1082 * this Device may not support all OCE AP functionalities but can support 1083 * only OCE STA-CFON functionalities. 1084 * @QCA_WLAN_VENDOR_FEATURE_SELF_MANAGED_REGULATORY: Device supports self 1085 * managed regulatory. 1086 * @QCA_WLAN_VENDOR_FEATURE_TWT: Device supports TWT (Target Wake Time). 1087 * @NUM_QCA_WLAN_VENDOR_FEATURES: Number of assigned feature bits 1088 */ 1089 enum qca_wlan_vendor_features { 1090 QCA_WLAN_VENDOR_FEATURE_KEY_MGMT_OFFLOAD = 0, 1091 QCA_WLAN_VENDOR_FEATURE_SUPPORT_HW_MODE_ANY = 1, 1092 QCA_WLAN_VENDOR_FEATURE_OFFCHANNEL_SIMULTANEOUS = 2, 1093 QCA_WLAN_VENDOR_FEATURE_P2P_LISTEN_OFFLOAD = 3, 1094 QCA_WLAN_VENDOR_FEATURE_OCE_STA = 4, 1095 QCA_WLAN_VENDOR_FEATURE_OCE_AP = 5, 1096 QCA_WLAN_VENDOR_FEATURE_OCE_STA_CFON = 6, 1097 QCA_WLAN_VENDOR_FEATURE_SELF_MANAGED_REGULATORY = 7, 1098 QCA_WLAN_VENDOR_FEATURE_TWT = 8, 1099 NUM_QCA_WLAN_VENDOR_FEATURES /* keep last */ 1100 }; 1101 1102 /** 1103 * enum qca_wlan_vendor_attr_data_offload_ind - Vendor Data Offload Indication 1104 * 1105 * @QCA_WLAN_VENDOR_ATTR_DATA_OFFLOAD_IND_SESSION: Session corresponding to 1106 * the offloaded data. 1107 * @QCA_WLAN_VENDOR_ATTR_DATA_OFFLOAD_IND_PROTOCOL: Protocol of the offloaded 1108 * data. 1109 * @QCA_WLAN_VENDOR_ATTR_DATA_OFFLOAD_IND_EVENT: Event type for the data offload 1110 * indication. 1111 */ 1112 enum qca_wlan_vendor_attr_data_offload_ind { 1113 QCA_WLAN_VENDOR_ATTR_DATA_OFFLOAD_IND_INVALID = 0, 1114 QCA_WLAN_VENDOR_ATTR_DATA_OFFLOAD_IND_SESSION, 1115 QCA_WLAN_VENDOR_ATTR_DATA_OFFLOAD_IND_PROTOCOL, 1116 QCA_WLAN_VENDOR_ATTR_DATA_OFFLOAD_IND_EVENT, 1117 1118 /* keep last */ 1119 QCA_WLAN_VENDOR_ATTR_DATA_OFFLOAD_IND_AFTER_LAST, 1120 QCA_WLAN_VENDOR_ATTR_DATA_OFFLOAD_IND_MAX = 1121 QCA_WLAN_VENDOR_ATTR_DATA_OFFLOAD_IND_AFTER_LAST - 1 1122 }; 1123 1124 /** 1125 * enum qca_wlan_vendor_attr_ocb_set_config - Vendor subcmd attributes to set 1126 * OCB config 1127 * 1128 * @QCA_WLAN_VENDOR_ATTR_OCB_SET_CONFIG_CHANNEL_COUNT: Number of channels in the 1129 * configuration 1130 * @QCA_WLAN_VENDOR_ATTR_OCB_SET_CONFIG_SCHEDULE_SIZE: Size of the schedule 1131 * @QCA_WLAN_VENDOR_ATTR_OCB_SET_CONFIG_CHANNEL_ARRAY: Array of channels 1132 * @QCA_WLAN_VENDOR_ATTR_OCB_SET_CONFIG_SCHEDULE_ARRAY: Array of channels to be 1133 * scheduled 1134 * @QCA_WLAN_VENDOR_ATTR_OCB_SET_CONFIG_NDL_CHANNEL_ARRAY: Array of NDL channel 1135 * information 1136 * @QCA_WLAN_VENDOR_ATTR_OCB_SET_CONFIG_NDL_ACTIVE_STATE_ARRAY: Array of NDL 1137 * active state configuration 1138 * @QCA_WLAN_VENDOR_ATTR_OCB_SET_CONFIG_FLAGS: Configuration flags such as 1139 * OCB_CONFIG_FLAG_80211_FRAME_MODE 1140 * @QCA_WLAN_VENDOR_ATTR_OCB_SET_CONFIG_DEF_TX_PARAM: Default TX parameters to 1141 * use in the case that a packet is sent without a TX control header 1142 * @QCA_WLAN_VENDOR_ATTR_OCB_SET_CONFIG_TA_MAX_DURATION: Max duration after the 1143 * last TA received that the local time set by TA is synchronous to other 1144 * communicating OCB STAs. 1145 */ 1146 enum qca_wlan_vendor_attr_ocb_set_config { 1147 QCA_WLAN_VENDOR_ATTR_OCB_SET_CONFIG_INVALID = 0, 1148 QCA_WLAN_VENDOR_ATTR_OCB_SET_CONFIG_CHANNEL_COUNT = 1, 1149 QCA_WLAN_VENDOR_ATTR_OCB_SET_CONFIG_SCHEDULE_SIZE = 2, 1150 QCA_WLAN_VENDOR_ATTR_OCB_SET_CONFIG_CHANNEL_ARRAY = 3, 1151 QCA_WLAN_VENDOR_ATTR_OCB_SET_CONFIG_SCHEDULE_ARRAY = 4, 1152 QCA_WLAN_VENDOR_ATTR_OCB_SET_CONFIG_NDL_CHANNEL_ARRAY = 5, 1153 QCA_WLAN_VENDOR_ATTR_OCB_SET_CONFIG_NDL_ACTIVE_STATE_ARRAY = 6, 1154 QCA_WLAN_VENDOR_ATTR_OCB_SET_CONFIG_FLAGS = 7, 1155 QCA_WLAN_VENDOR_ATTR_OCB_SET_CONFIG_DEF_TX_PARAM = 8, 1156 QCA_WLAN_VENDOR_ATTR_OCB_SET_CONFIG_TA_MAX_DURATION = 9, 1157 QCA_WLAN_VENDOR_ATTR_OCB_SET_CONFIG_AFTER_LAST, 1158 QCA_WLAN_VENDOR_ATTR_OCB_SET_CONFIG_MAX = 1159 QCA_WLAN_VENDOR_ATTR_OCB_SET_CONFIG_AFTER_LAST - 1 1160 }; 1161 1162 /** 1163 * enum qca_wlan_vendor_attr_ocb_set_utc_time - Vendor subcmd attributes to set 1164 * UTC time 1165 * 1166 * @QCA_WLAN_VENDOR_ATTR_OCB_SET_UTC_TIME_VALUE: The UTC time as an array of 1167 * 10 bytes 1168 * @QCA_WLAN_VENDOR_ATTR_OCB_SET_UTC_TIME_ERROR: The time error as an array of 1169 * 5 bytes 1170 */ 1171 enum qca_wlan_vendor_attr_ocb_set_utc_time { 1172 QCA_WLAN_VENDOR_ATTR_OCB_SET_UTC_TIME_INVALID = 0, 1173 QCA_WLAN_VENDOR_ATTR_OCB_SET_UTC_TIME_VALUE = 1, 1174 QCA_WLAN_VENDOR_ATTR_OCB_SET_UTC_TIME_ERROR = 2, 1175 QCA_WLAN_VENDOR_ATTR_OCB_SET_UTC_TIME_AFTER_LAST, 1176 QCA_WLAN_VENDOR_ATTR_OCB_SET_UTC_TIME_MAX = 1177 QCA_WLAN_VENDOR_ATTR_OCB_SET_UTC_TIME_AFTER_LAST - 1 1178 }; 1179 1180 /** 1181 * enum qca_wlan_vendor_attr_ocb_start_timing_advert - Vendor subcmd attributes 1182 * to start sending timing advert frames 1183 * 1184 * @QCA_WLAN_VENDOR_ATTR_OCB_START_TIMING_ADVERT_CHANNEL_FREQ: Cannel frequency 1185 * on which to send the frames 1186 * @QCA_WLAN_VENDOR_ATTR_OCB_START_TIMING_ADVERT_REPEAT_RATE: Number of times 1187 * the frame is sent in 5 seconds 1188 */ 1189 enum qca_wlan_vendor_attr_ocb_start_timing_advert { 1190 QCA_WLAN_VENDOR_ATTR_OCB_START_TIMING_ADVERT_INVALID = 0, 1191 QCA_WLAN_VENDOR_ATTR_OCB_START_TIMING_ADVERT_CHANNEL_FREQ = 1, 1192 QCA_WLAN_VENDOR_ATTR_OCB_START_TIMING_ADVERT_REPEAT_RATE = 2, 1193 QCA_WLAN_VENDOR_ATTR_OCB_START_TIMING_ADVERT_AFTER_LAST, 1194 QCA_WLAN_VENDOR_ATTR_OCB_START_TIMING_ADVERT_MAX = 1195 QCA_WLAN_VENDOR_ATTR_OCB_START_TIMING_ADVERT_AFTER_LAST - 1 1196 }; 1197 1198 /** 1199 * enum qca_wlan_vendor_attr_ocb_stop_timing_advert - Vendor subcmd attributes 1200 * to stop timing advert 1201 * 1202 * @QCA_WLAN_VENDOR_ATTR_OCB_STOP_TIMING_ADVERT_CHANNEL_FREQ: The channel 1203 * frequency on which to stop the timing advert 1204 */ 1205 enum qca_wlan_vendor_attr_ocb_stop_timing_advert { 1206 QCA_WLAN_VENDOR_ATTR_OCB_STOP_TIMING_ADVERT_INVALID = 0, 1207 QCA_WLAN_VENDOR_ATTR_OCB_STOP_TIMING_ADVERT_CHANNEL_FREQ = 1, 1208 QCA_WLAN_VENDOR_ATTR_OCB_STOP_TIMING_ADVERT_AFTER_LAST, 1209 QCA_WLAN_VENDOR_ATTR_OCB_STOP_TIMING_ADVERT_MAX = 1210 QCA_WLAN_VENDOR_ATTR_OCB_STOP_TIMING_ADVERT_AFTER_LAST - 1 1211 }; 1212 1213 /** 1214 * enum qca_wlan_vendor_attr_ocb_get_tsf_response - Vendor subcmd attributes to 1215 * get TSF timer value 1216 * 1217 * @QCA_WLAN_VENDOR_ATTR_OCB_GET_TSF_RESP_TIMER_HIGH: Higher 32 bits of the 1218 * timer 1219 * @QCA_WLAN_VENDOR_ATTR_OCB_GET_TSF_RESP_TIMER_LOW: Lower 32 bits of the timer 1220 */ 1221 enum qca_wlan_vendor_attr_ocb_get_tsf_resp { 1222 QCA_WLAN_VENDOR_ATTR_OCB_GET_TSF_RESP_INVALID = 0, 1223 QCA_WLAN_VENDOR_ATTR_OCB_GET_TSF_RESP_TIMER_HIGH = 1, 1224 QCA_WLAN_VENDOR_ATTR_OCB_GET_TSF_RESP_TIMER_LOW = 2, 1225 QCA_WLAN_VENDOR_ATTR_OCB_GET_TSF_RESP_AFTER_LAST, 1226 QCA_WLAN_VENDOR_ATTR_OCB_GET_TSF_RESP_MAX = 1227 QCA_WLAN_VENDOR_ATTR_OCB_GET_TSF_RESP_AFTER_LAST - 1 1228 }; 1229 1230 enum qca_vendor_attr_get_preferred_freq_list { 1231 QCA_WLAN_VENDOR_ATTR_GET_PREFERRED_FREQ_LIST_INVALID, 1232 /* A 32-unsigned value; the interface type/mode for which the preferred 1233 * frequency list is requested (see enum qca_iface_type for possible 1234 * values); used in GET_PREFERRED_FREQ_LIST command from user-space to 1235 * kernel and in the kernel response back to user-space. 1236 */ 1237 QCA_WLAN_VENDOR_ATTR_GET_PREFERRED_FREQ_LIST_IFACE_TYPE, 1238 /* An array of 32-unsigned values; values are frequency (MHz); sent 1239 * from kernel space to user space. 1240 */ 1241 QCA_WLAN_VENDOR_ATTR_GET_PREFERRED_FREQ_LIST, 1242 /* An array of nested values as per enum qca_wlan_vendor_attr_pcl 1243 * attribute. Each element contains frequency (MHz), weight, and flag 1244 * bit mask indicating how the frequency should be used in P2P 1245 * negotiation; sent from kernel space to user space. 1246 */ 1247 QCA_WLAN_VENDOR_ATTR_GET_PREFERRED_FREQ_LIST_WEIGHED_PCL, 1248 /* keep last */ 1249 QCA_WLAN_VENDOR_ATTR_GET_PREFERRED_FREQ_LIST_AFTER_LAST, 1250 QCA_WLAN_VENDOR_ATTR_GET_PREFERRED_FREQ_LIST_MAX = 1251 QCA_WLAN_VENDOR_ATTR_GET_PREFERRED_FREQ_LIST_AFTER_LAST - 1 1252 }; 1253 1254 enum qca_vendor_attr_probable_oper_channel { 1255 QCA_WLAN_VENDOR_ATTR_PROBABLE_OPER_CHANNEL_INVALID, 1256 /* 32-bit unsigned value; indicates the connection/iface type likely to 1257 * come on this channel (see enum qca_iface_type). 1258 */ 1259 QCA_WLAN_VENDOR_ATTR_PROBABLE_OPER_CHANNEL_IFACE_TYPE, 1260 /* 32-bit unsigned value; the frequency (MHz) of the probable channel */ 1261 QCA_WLAN_VENDOR_ATTR_PROBABLE_OPER_CHANNEL_FREQ, 1262 /* keep last */ 1263 QCA_WLAN_VENDOR_ATTR_PROBABLE_OPER_CHANNEL_AFTER_LAST, 1264 QCA_WLAN_VENDOR_ATTR_PROBABLE_OPER_CHANNEL_MAX = 1265 QCA_WLAN_VENDOR_ATTR_PROBABLE_OPER_CHANNEL_AFTER_LAST - 1 1266 }; 1267 1268 enum qca_iface_type { 1269 QCA_IFACE_TYPE_STA, 1270 QCA_IFACE_TYPE_AP, 1271 QCA_IFACE_TYPE_P2P_CLIENT, 1272 QCA_IFACE_TYPE_P2P_GO, 1273 QCA_IFACE_TYPE_IBSS, 1274 QCA_IFACE_TYPE_TDLS, 1275 }; 1276 1277 enum qca_set_band { 1278 QCA_SETBAND_AUTO, 1279 QCA_SETBAND_5G, 1280 QCA_SETBAND_2G, 1281 }; 1282 1283 /** 1284 * enum qca_access_policy - Access control policy 1285 * 1286 * Access control policy is applied on the configured IE 1287 * (QCA_WLAN_VENDOR_ATTR_CONFIG_ACCESS_POLICY_IE). 1288 * To be set with QCA_WLAN_VENDOR_ATTR_CONFIG_ACCESS_POLICY. 1289 * 1290 * @QCA_ACCESS_POLICY_ACCEPT_UNLESS_LISTED: Deny Wi-Fi connections which match 1291 * the specific configuration (IE) set, i.e., allow all the 1292 * connections which do not match the configuration. 1293 * @QCA_ACCESS_POLICY_DENY_UNLESS_LISTED: Accept Wi-Fi connections which match 1294 * the specific configuration (IE) set, i.e., deny all the 1295 * connections which do not match the configuration. 1296 */ 1297 enum qca_access_policy { 1298 QCA_ACCESS_POLICY_ACCEPT_UNLESS_LISTED, 1299 QCA_ACCESS_POLICY_DENY_UNLESS_LISTED, 1300 }; 1301 1302 /** 1303 * enum qca_vendor_attr_get_tsf: Vendor attributes for TSF capture 1304 * @QCA_WLAN_VENDOR_ATTR_TSF_CMD: enum qca_tsf_operation (u32) 1305 * @QCA_WLAN_VENDOR_ATTR_TSF_TIMER_VALUE: Unsigned 64 bit TSF timer value 1306 * @QCA_WLAN_VENDOR_ATTR_TSF_SOC_TIMER_VALUE: Unsigned 64 bit Synchronized 1307 * SOC timer value at TSF capture 1308 */ 1309 enum qca_vendor_attr_tsf_cmd { 1310 QCA_WLAN_VENDOR_ATTR_TSF_INVALID = 0, 1311 QCA_WLAN_VENDOR_ATTR_TSF_CMD, 1312 QCA_WLAN_VENDOR_ATTR_TSF_TIMER_VALUE, 1313 QCA_WLAN_VENDOR_ATTR_TSF_SOC_TIMER_VALUE, 1314 QCA_WLAN_VENDOR_ATTR_TSF_AFTER_LAST, 1315 QCA_WLAN_VENDOR_ATTR_TSF_MAX = 1316 QCA_WLAN_VENDOR_ATTR_TSF_AFTER_LAST - 1 1317 }; 1318 1319 /** 1320 * enum qca_tsf_operation: TSF driver commands 1321 * @QCA_TSF_CAPTURE: Initiate TSF Capture 1322 * @QCA_TSF_GET: Get TSF capture value 1323 * @QCA_TSF_SYNC_GET: Initiate TSF capture and return with captured value 1324 */ 1325 enum qca_tsf_cmd { 1326 QCA_TSF_CAPTURE, 1327 QCA_TSF_GET, 1328 QCA_TSF_SYNC_GET, 1329 }; 1330 1331 /** 1332 * enum qca_vendor_attr_wisa_cmd 1333 * @QCA_WLAN_VENDOR_ATTR_WISA_MODE: WISA mode value (u32) 1334 * WISA setup vendor commands 1335 */ 1336 enum qca_vendor_attr_wisa_cmd { 1337 QCA_WLAN_VENDOR_ATTR_WISA_INVALID = 0, 1338 QCA_WLAN_VENDOR_ATTR_WISA_MODE, 1339 QCA_WLAN_VENDOR_ATTR_WISA_AFTER_LAST, 1340 QCA_WLAN_VENDOR_ATTR_WISA_MAX = 1341 QCA_WLAN_VENDOR_ATTR_WISA_AFTER_LAST - 1 1342 }; 1343 1344 /* IEEE 802.11 Vendor Specific elements */ 1345 1346 /** 1347 * enum qca_vendor_element_id - QCA Vendor Specific element types 1348 * 1349 * These values are used to identify QCA Vendor Specific elements. The 1350 * payload of the element starts with the three octet OUI (OUI_QCA) and 1351 * is followed by a single octet type which is defined by this enum. 1352 * 1353 * @QCA_VENDOR_ELEM_P2P_PREF_CHAN_LIST: P2P preferred channel list. 1354 * This element can be used to specify preference order for supported 1355 * channels. The channels in this list are in preference order (the first 1356 * one has the highest preference) and are described as a pair of 1357 * (global) Operating Class and Channel Number (each one octet) fields. 1358 * 1359 * This extends the standard P2P functionality by providing option to have 1360 * more than one preferred operating channel. When this element is present, 1361 * it replaces the preference indicated in the Operating Channel attribute. 1362 * For supporting other implementations, the Operating Channel attribute is 1363 * expected to be used with the highest preference channel. Similarly, all 1364 * the channels included in this Preferred channel list element are 1365 * expected to be included in the Channel List attribute. 1366 * 1367 * This vendor element may be included in GO Negotiation Request, P2P 1368 * Invitation Request, and Provision Discovery Request frames. 1369 * 1370 * @QCA_VENDOR_ELEM_HE_CAPAB: HE Capabilities element. 1371 * This element can be used for pre-standard publication testing of HE 1372 * before P802.11ax draft assigns the element ID. The payload of this 1373 * vendor specific element is defined by the latest P802.11ax draft. 1374 * Please note that the draft is still work in progress and this element 1375 * payload is subject to change. 1376 * 1377 * @QCA_VENDOR_ELEM_HE_OPER: HE Operation element. 1378 * This element can be used for pre-standard publication testing of HE 1379 * before P802.11ax draft assigns the element ID. The payload of this 1380 * vendor specific element is defined by the latest P802.11ax draft. 1381 * Please note that the draft is still work in progress and this element 1382 * payload is subject to change. 1383 * 1384 * @QCA_VENDOR_ELEM_RAPS: RAPS element (OFDMA-based Random Access Parameter Set 1385 * element). 1386 * This element can be used for pre-standard publication testing of HE 1387 * before P802.11ax draft assigns the element ID extension. The payload of 1388 * this vendor specific element is defined by the latest P802.11ax draft 1389 * (not including the Element ID Extension field). Please note that the 1390 * draft is still work in progress and this element payload is subject to 1391 * change. 1392 * 1393 * @QCA_VENDOR_ELEM_MU_EDCA_PARAMS: MU EDCA Parameter Set element. 1394 * This element can be used for pre-standard publication testing of HE 1395 * before P802.11ax draft assigns the element ID extension. The payload of 1396 * this vendor specific element is defined by the latest P802.11ax draft 1397 * (not including the Element ID Extension field). Please note that the 1398 * draft is still work in progress and this element payload is subject to 1399 * change. 1400 * 1401 * @QCA_VENDOR_ELEM_BSS_COLOR_CHANGE: BSS Color Change Announcement element. 1402 * This element can be used for pre-standard publication testing of HE 1403 * before P802.11ax draft assigns the element ID extension. The payload of 1404 * this vendor specific element is defined by the latest P802.11ax draft 1405 * (not including the Element ID Extension field). Please note that the 1406 * draft is still work in progress and this element payload is subject to 1407 * change. 1408 */ 1409 enum qca_vendor_element_id { 1410 QCA_VENDOR_ELEM_P2P_PREF_CHAN_LIST = 0, 1411 QCA_VENDOR_ELEM_HE_CAPAB = 1, 1412 QCA_VENDOR_ELEM_HE_OPER = 2, 1413 QCA_VENDOR_ELEM_RAPS = 3, 1414 QCA_VENDOR_ELEM_MU_EDCA_PARAMS = 4, 1415 QCA_VENDOR_ELEM_BSS_COLOR_CHANGE = 5, 1416 }; 1417 1418 /** 1419 * enum qca_wlan_vendor_attr_scan - Specifies vendor scan attributes 1420 * 1421 * @QCA_WLAN_VENDOR_ATTR_SCAN_IE: IEs that should be included as part of scan 1422 * @QCA_WLAN_VENDOR_ATTR_SCAN_FREQUENCIES: Nested unsigned 32-bit attributes 1423 * with frequencies to be scanned (in MHz) 1424 * @QCA_WLAN_VENDOR_ATTR_SCAN_SSIDS: Nested attribute with SSIDs to be scanned 1425 * @QCA_WLAN_VENDOR_ATTR_SCAN_SUPP_RATES: Nested array attribute of supported 1426 * rates to be included 1427 * @QCA_WLAN_VENDOR_ATTR_SCAN_TX_NO_CCK_RATE: flag used to send probe requests 1428 * at non CCK rate in 2GHz band 1429 * @QCA_WLAN_VENDOR_ATTR_SCAN_FLAGS: Unsigned 32-bit scan flags 1430 * @QCA_WLAN_VENDOR_ATTR_SCAN_COOKIE: Unsigned 64-bit cookie provided by the 1431 * driver for the specific scan request 1432 * @QCA_WLAN_VENDOR_ATTR_SCAN_STATUS: Unsigned 8-bit status of the scan 1433 * request decoded as in enum scan_status 1434 * @QCA_WLAN_VENDOR_ATTR_SCAN_MAC: 6-byte MAC address to use when randomisation 1435 * scan flag is set 1436 * @QCA_WLAN_VENDOR_ATTR_SCAN_MAC_MASK: 6-byte MAC address mask to be used with 1437 * randomisation 1438 * @QCA_WLAN_VENDOR_ATTR_SCAN_BSSID: 6-byte MAC address representing the 1439 * specific BSSID to scan for. 1440 */ 1441 enum qca_wlan_vendor_attr_scan { 1442 QCA_WLAN_VENDOR_ATTR_SCAN_INVALID_PARAM = 0, 1443 QCA_WLAN_VENDOR_ATTR_SCAN_IE = 1, 1444 QCA_WLAN_VENDOR_ATTR_SCAN_FREQUENCIES = 2, 1445 QCA_WLAN_VENDOR_ATTR_SCAN_SSIDS = 3, 1446 QCA_WLAN_VENDOR_ATTR_SCAN_SUPP_RATES = 4, 1447 QCA_WLAN_VENDOR_ATTR_SCAN_TX_NO_CCK_RATE = 5, 1448 QCA_WLAN_VENDOR_ATTR_SCAN_FLAGS = 6, 1449 QCA_WLAN_VENDOR_ATTR_SCAN_COOKIE = 7, 1450 QCA_WLAN_VENDOR_ATTR_SCAN_STATUS = 8, 1451 QCA_WLAN_VENDOR_ATTR_SCAN_MAC = 9, 1452 QCA_WLAN_VENDOR_ATTR_SCAN_MAC_MASK = 10, 1453 QCA_WLAN_VENDOR_ATTR_SCAN_BSSID = 11, 1454 QCA_WLAN_VENDOR_ATTR_SCAN_AFTER_LAST, 1455 QCA_WLAN_VENDOR_ATTR_SCAN_MAX = 1456 QCA_WLAN_VENDOR_ATTR_SCAN_AFTER_LAST - 1 1457 }; 1458 1459 /** 1460 * enum scan_status - Specifies the valid values the vendor scan attribute 1461 * QCA_WLAN_VENDOR_ATTR_SCAN_STATUS can take 1462 * 1463 * @VENDOR_SCAN_STATUS_NEW_RESULTS: implies the vendor scan is successful with 1464 * new scan results 1465 * @VENDOR_SCAN_STATUS_ABORTED: implies the vendor scan was aborted in-between 1466 */ 1467 enum scan_status { 1468 VENDOR_SCAN_STATUS_NEW_RESULTS, 1469 VENDOR_SCAN_STATUS_ABORTED, 1470 VENDOR_SCAN_STATUS_MAX, 1471 }; 1472 1473 /** 1474 * enum qca_vendor_attr_ota_test - Specifies the values for vendor 1475 * command QCA_NL80211_VENDOR_SUBCMD_OTA_TEST 1476 * @QCA_WLAN_VENDOR_ATTR_OTA_TEST_ENABLE: enable ota test 1477 */ 1478 enum qca_vendor_attr_ota_test { 1479 QCA_WLAN_VENDOR_ATTR_OTA_TEST_INVALID, 1480 /* 8-bit unsigned value to indicate if OTA test is enabled */ 1481 QCA_WLAN_VENDOR_ATTR_OTA_TEST_ENABLE, 1482 /* keep last */ 1483 QCA_WLAN_VENDOR_ATTR_OTA_TEST_AFTER_LAST, 1484 QCA_WLAN_VENDOR_ATTR_OTA_TEST_MAX = 1485 QCA_WLAN_VENDOR_ATTR_OTA_TEST_AFTER_LAST - 1 1486 }; 1487 1488 /** 1489 * enum qca_vendor_attr_txpower_scale - vendor sub commands index 1490 * 1491 * @QCA_WLAN_VENDOR_ATTR_TXPOWER_SCALE: scaling value 1492 */ 1493 enum qca_vendor_attr_txpower_scale { 1494 QCA_WLAN_VENDOR_ATTR_TXPOWER_SCALE_INVALID, 1495 /* 8-bit unsigned value to indicate the scaling of tx power */ 1496 QCA_WLAN_VENDOR_ATTR_TXPOWER_SCALE, 1497 /* keep last */ 1498 QCA_WLAN_VENDOR_ATTR_TXPOWER_SCALE_AFTER_LAST, 1499 QCA_WLAN_VENDOR_ATTR_TXPOWER_SCALE_MAX = 1500 QCA_WLAN_VENDOR_ATTR_TXPOWER_SCALE_AFTER_LAST - 1 1501 }; 1502 1503 /** 1504 * enum qca_vendor_attr_txpower_decr_db - Attributes for TX power decrease 1505 * 1506 * These attributes are used with QCA_NL80211_VENDOR_SUBCMD_SET_TXPOWER_DECR_DB. 1507 */ 1508 enum qca_vendor_attr_txpower_decr_db { 1509 QCA_WLAN_VENDOR_ATTR_TXPOWER_DECR_DB_INVALID, 1510 /* 8-bit unsigned value to indicate the reduction of TX power in dB for 1511 * a virtual interface. 1512 */ 1513 QCA_WLAN_VENDOR_ATTR_TXPOWER_DECR_DB, 1514 /* keep last */ 1515 QCA_WLAN_VENDOR_ATTR_TXPOWER_DECR_DB_AFTER_LAST, 1516 QCA_WLAN_VENDOR_ATTR_TXPOWER_DECR_DB_MAX = 1517 QCA_WLAN_VENDOR_ATTR_TXPOWER_DECR_DB_AFTER_LAST - 1 1518 }; 1519 1520 /* Attributes for data used by 1521 * QCA_NL80211_VENDOR_SUBCMD_SET_WIFI_CONFIGURATION and 1522 * QCA_NL80211_VENDOR_SUBCMD_GET_WIFI_CONFIGURATION subcommands. 1523 */ 1524 enum qca_wlan_vendor_attr_config { 1525 QCA_WLAN_VENDOR_ATTR_CONFIG_INVALID = 0, 1526 /* Unsigned 32-bit value to set the DTIM period. 1527 * Whether the wifi chipset wakes at every dtim beacon or a multiple of 1528 * the DTIM period. If DTIM is set to 3, the STA shall wake up every 3 1529 * DTIM beacons. 1530 */ 1531 QCA_WLAN_VENDOR_ATTR_CONFIG_DYNAMIC_DTIM = 1, 1532 /* Unsigned 32-bit value to set the wifi_iface stats averaging factor 1533 * used to calculate statistics like average the TSF offset or average 1534 * number of frame leaked. 1535 * For instance, upon Beacon frame reception: 1536 * current_avg = ((beacon_TSF - TBTT) * factor + previous_avg * (0x10000 - factor) ) / 0x10000 1537 * For instance, when evaluating leaky APs: 1538 * current_avg = ((num frame received within guard time) * factor + previous_avg * (0x10000 - factor)) / 0x10000 1539 */ 1540 QCA_WLAN_VENDOR_ATTR_CONFIG_STATS_AVG_FACTOR = 2, 1541 /* Unsigned 32-bit value to configure guard time, i.e., when 1542 * implementing IEEE power management based on frame control PM bit, how 1543 * long the driver waits before shutting down the radio and after 1544 * receiving an ACK frame for a Data frame with PM bit set. 1545 */ 1546 QCA_WLAN_VENDOR_ATTR_CONFIG_GUARD_TIME = 3, 1547 /* Unsigned 32-bit value to change the FTM capability dynamically */ 1548 QCA_WLAN_VENDOR_ATTR_CONFIG_FINE_TIME_MEASUREMENT = 4, 1549 /* Unsigned 16-bit value to configure maximum TX rate dynamically */ 1550 QCA_WLAN_VENDOR_ATTR_CONF_TX_RATE = 5, 1551 /* Unsigned 32-bit value to configure the number of continuous 1552 * Beacon Miss which shall be used by the firmware to penalize 1553 * the RSSI. 1554 */ 1555 QCA_WLAN_VENDOR_ATTR_CONFIG_PENALIZE_AFTER_NCONS_BEACON_MISS = 6, 1556 /* Unsigned 8-bit value to configure the channel avoidance indication 1557 * behavior. Firmware to send only one indication and ignore duplicate 1558 * indications when set to avoid multiple Apps wakeups. 1559 */ 1560 QCA_WLAN_VENDOR_ATTR_CONFIG_CHANNEL_AVOIDANCE_IND = 7, 1561 /* 8-bit unsigned value to configure the maximum TX MPDU for 1562 * aggregation. 1563 */ 1564 QCA_WLAN_VENDOR_ATTR_CONFIG_TX_MPDU_AGGREGATION = 8, 1565 /* 8-bit unsigned value to configure the maximum RX MPDU for 1566 * aggregation. 1567 */ 1568 QCA_WLAN_VENDOR_ATTR_CONFIG_RX_MPDU_AGGREGATION = 9, 1569 /* 8-bit unsigned value to configure the Non aggregrate/11g sw 1570 * retry threshold (0 disable, 31 max). 1571 */ 1572 QCA_WLAN_VENDOR_ATTR_CONFIG_NON_AGG_RETRY = 10, 1573 /* 8-bit unsigned value to configure the aggregrate sw 1574 * retry threshold (0 disable, 31 max). 1575 */ 1576 QCA_WLAN_VENDOR_ATTR_CONFIG_AGG_RETRY = 11, 1577 /* 8-bit unsigned value to configure the MGMT frame 1578 * retry threshold (0 disable, 31 max). 1579 */ 1580 QCA_WLAN_VENDOR_ATTR_CONFIG_MGMT_RETRY = 12, 1581 /* 8-bit unsigned value to configure the CTRL frame 1582 * retry threshold (0 disable, 31 max). 1583 */ 1584 QCA_WLAN_VENDOR_ATTR_CONFIG_CTRL_RETRY = 13, 1585 /* 8-bit unsigned value to configure the propagation delay for 1586 * 2G/5G band (0~63, units in us) 1587 */ 1588 QCA_WLAN_VENDOR_ATTR_CONFIG_PROPAGATION_DELAY = 14, 1589 /* Unsigned 32-bit value to configure the number of unicast TX fail 1590 * packet count. The peer is disconnected once this threshold is 1591 * reached. 1592 */ 1593 QCA_WLAN_VENDOR_ATTR_CONFIG_TX_FAIL_COUNT = 15, 1594 /* Attribute used to set scan default IEs to the driver. 1595 * 1596 * These IEs can be used by scan operations that will be initiated by 1597 * the driver/firmware. 1598 * 1599 * For further scan requests coming to the driver, these IEs should be 1600 * merged with the IEs received along with scan request coming to the 1601 * driver. If a particular IE is present in the scan default IEs but not 1602 * present in the scan request, then that IE should be added to the IEs 1603 * sent in the Probe Request frames for that scan request. 1604 */ 1605 QCA_WLAN_VENDOR_ATTR_CONFIG_SCAN_DEFAULT_IES = 16, 1606 /* Unsigned 32-bit attribute for generic commands */ 1607 QCA_WLAN_VENDOR_ATTR_CONFIG_GENERIC_COMMAND = 17, 1608 /* Unsigned 32-bit value attribute for generic commands */ 1609 QCA_WLAN_VENDOR_ATTR_CONFIG_GENERIC_VALUE = 18, 1610 /* Unsigned 32-bit data attribute for generic command response */ 1611 QCA_WLAN_VENDOR_ATTR_CONFIG_GENERIC_DATA = 19, 1612 /* Unsigned 32-bit length attribute for 1613 * QCA_WLAN_VENDOR_ATTR_CONFIG_GENERIC_DATA 1614 */ 1615 QCA_WLAN_VENDOR_ATTR_CONFIG_GENERIC_LENGTH = 20, 1616 /* Unsigned 32-bit flags attribute for 1617 * QCA_WLAN_VENDOR_ATTR_CONFIG_GENERIC_DATA 1618 */ 1619 QCA_WLAN_VENDOR_ATTR_CONFIG_GENERIC_FLAGS = 21, 1620 /* Unsigned 32-bit, defining the access policy. 1621 * See enum qca_access_policy. Used with 1622 * QCA_WLAN_VENDOR_ATTR_CONFIG_ACCESS_POLICY_IE_LIST. 1623 */ 1624 QCA_WLAN_VENDOR_ATTR_CONFIG_ACCESS_POLICY = 22, 1625 /* Sets the list of full set of IEs for which a specific access policy 1626 * has to be applied. Used along with 1627 * QCA_WLAN_VENDOR_ATTR_CONFIG_ACCESS_POLICY to control the access. 1628 * Zero length payload can be used to clear this access constraint. 1629 */ 1630 QCA_WLAN_VENDOR_ATTR_CONFIG_ACCESS_POLICY_IE_LIST = 23, 1631 /* Unsigned 32-bit, specifies the interface index (netdev) for which the 1632 * corresponding configurations are applied. If the interface index is 1633 * not specified, the configurations are attributed to the respective 1634 * wiphy. 1635 */ 1636 QCA_WLAN_VENDOR_ATTR_CONFIG_IFINDEX = 24, 1637 /* 8-bit unsigned value to trigger QPower: 1-Enable, 0-Disable */ 1638 QCA_WLAN_VENDOR_ATTR_CONFIG_QPOWER = 25, 1639 /* 8-bit unsigned value to configure the driver and below layers to 1640 * ignore the assoc disallowed set by APs while connecting 1641 * 1-Ignore, 0-Don't ignore 1642 */ 1643 QCA_WLAN_VENDOR_ATTR_CONFIG_IGNORE_ASSOC_DISALLOWED = 26, 1644 /* 32-bit unsigned value to trigger antenna diversity features: 1645 * 1-Enable, 0-Disable 1646 */ 1647 QCA_WLAN_VENDOR_ATTR_CONFIG_ANT_DIV_ENA = 27, 1648 /* 32-bit unsigned value to configure specific chain antenna */ 1649 QCA_WLAN_VENDOR_ATTR_CONFIG_ANT_DIV_CHAIN = 28, 1650 /* 32-bit unsigned value to trigger cycle selftest 1651 * 1-Enable, 0-Disable 1652 */ 1653 QCA_WLAN_VENDOR_ATTR_CONFIG_ANT_DIV_SELFTEST = 29, 1654 /* 32-bit unsigned to configure the cycle time of selftest 1655 * the unit is micro-second 1656 */ 1657 QCA_WLAN_VENDOR_ATTR_CONFIG_ANT_DIV_SELFTEST_INTVL = 30, 1658 /* 32-bit unsigned value to set reorder timeout for AC_VO */ 1659 QCA_WLAN_VENDOR_ATTR_CONFIG_RX_REORDER_TIMEOUT_VOICE = 31, 1660 /* 32-bit unsigned value to set reorder timeout for AC_VI */ 1661 QCA_WLAN_VENDOR_ATTR_CONFIG_RX_REORDER_TIMEOUT_VIDEO = 32, 1662 /* 32-bit unsigned value to set reorder timeout for AC_BE */ 1663 QCA_WLAN_VENDOR_ATTR_CONFIG_RX_REORDER_TIMEOUT_BESTEFFORT = 33, 1664 /* 32-bit unsigned value to set reorder timeout for AC_BK */ 1665 QCA_WLAN_VENDOR_ATTR_CONFIG_RX_REORDER_TIMEOUT_BACKGROUND = 34, 1666 /* 6-byte MAC address to point out the specific peer */ 1667 QCA_WLAN_VENDOR_ATTR_CONFIG_RX_BLOCKSIZE_PEER_MAC = 35, 1668 /* 32-bit unsigned value to set window size for specific peer */ 1669 QCA_WLAN_VENDOR_ATTR_CONFIG_RX_BLOCKSIZE_WINLIMIT = 36, 1670 /* 8-bit unsigned value to set the beacon miss threshold in 2.4 GHz */ 1671 QCA_WLAN_VENDOR_ATTR_CONFIG_BEACON_MISS_THRESHOLD_24 = 37, 1672 /* 8-bit unsigned value to set the beacon miss threshold in 5 GHz */ 1673 QCA_WLAN_VENDOR_ATTR_CONFIG_BEACON_MISS_THRESHOLD_5 = 38, 1674 /* 32-bit unsigned value to configure 5 or 10 MHz channel width for 1675 * station device while in disconnect state. The attribute use the 1676 * value of enum nl80211_chan_width: NL80211_CHAN_WIDTH_5 means 5 MHz, 1677 * NL80211_CHAN_WIDTH_10 means 10 MHz. If set, the device work in 5 or 1678 * 10 MHz channel width, the station will not connect to a BSS using 20 1679 * MHz or higher bandwidth. Set to NL80211_CHAN_WIDTH_20_NOHT to 1680 * clear this constraint. 1681 */ 1682 QCA_WLAN_VENDOR_ATTR_CONFIG_SUB20_CHAN_WIDTH = 39, 1683 /* 32-bit unsigned value to configure the propagation absolute delay 1684 * for 2G/5G band (units in us) 1685 */ 1686 QCA_WLAN_VENDOR_ATTR_CONFIG_PROPAGATION_ABS_DELAY = 40, 1687 /* 32-bit unsigned value to set probe period */ 1688 QCA_WLAN_VENDOR_ATTR_CONFIG_ANT_DIV_PROBE_PERIOD = 41, 1689 /* 32-bit unsigned value to set stay period */ 1690 QCA_WLAN_VENDOR_ATTR_CONFIG_ANT_DIV_STAY_PERIOD = 42, 1691 /* 32-bit unsigned value to set snr diff */ 1692 QCA_WLAN_VENDOR_ATTR_CONFIG_ANT_DIV_SNR_DIFF = 43, 1693 /* 32-bit unsigned value to set probe dwell time */ 1694 QCA_WLAN_VENDOR_ATTR_CONFIG_ANT_DIV_PROBE_DWELL_TIME = 44, 1695 /* 32-bit unsigned value to set mgmt snr weight */ 1696 QCA_WLAN_VENDOR_ATTR_CONFIG_ANT_DIV_MGMT_SNR_WEIGHT = 45, 1697 /* 32-bit unsigned value to set data snr weight */ 1698 QCA_WLAN_VENDOR_ATTR_CONFIG_ANT_DIV_DATA_SNR_WEIGHT = 46, 1699 /* 32-bit unsigned value to set ack snr weight */ 1700 QCA_WLAN_VENDOR_ATTR_CONFIG_ANT_DIV_ACK_SNR_WEIGHT = 47, 1701 /* 32-bit unsigned value to configure the listen interval. 1702 * This is in units of beacon intervals. This configuration alters 1703 * the negotiated listen interval with the AP during the connection. 1704 * It is highly recommended to configure a value less than or equal to 1705 * the one negotiated during the association. Configuring any greater 1706 * value can have adverse effects (frame loss, AP disassociating STA, 1707 * etc.). 1708 */ 1709 QCA_WLAN_VENDOR_ATTR_CONFIG_LISTEN_INTERVAL = 48, 1710 /* 1711 * 8 bit unsigned value that is set on an AP/GO virtual interface to 1712 * disable operations that would cause the AP/GO to leave its operating 1713 * channel. 1714 * 1715 * This will restrict the scans to the AP/GO operating channel and the 1716 * channels of the other band, if DBS is supported.A STA/CLI interface 1717 * brought up after this setting is enabled, will be restricted to 1718 * connecting to devices only on the AP/GO interface's operating channel 1719 * or on the other band in DBS case. P2P supported channel list is 1720 * modified, to only include AP interface's operating-channel and the 1721 * channels of the other band if DBS is supported. 1722 * 1723 * These restrictions are only applicable as long as the AP/GO interface 1724 * is alive. If the AP/GO interface is brought down then this 1725 * setting/restriction is forgotten. 1726 * 1727 * If this variable is set on an AP/GO interface while a multi-channel 1728 * concurrent session is active, it has no effect on the operation of 1729 * the current interfaces, other than restricting the scan to the AP/GO 1730 * operating channel and the other band channels if DBS is supported. 1731 * However, if the STA is brought down and restarted then the new STA 1732 * connection will either be formed on the AP/GO channel or on the 1733 * other band in a DBS case. This is because of the scan being 1734 * restricted on these channels as mentioned above. 1735 * 1736 * 1-Restrict / 0-Don't restrict offchannel operations. 1737 */ 1738 QCA_WLAN_VENDOR_ATTR_CONFIG_RESTRICT_OFFCHANNEL = 49, 1739 /* 1740 * 8 bit unsigned value to enable/disable LRO (Large Receive Offload) 1741 * on an interface. 1742 * 1 - Enable, 0 - Disable. 1743 */ 1744 QCA_WLAN_VENDOR_ATTR_CONFIG_LRO = 50, 1745 1746 /* 1747 * 8 bit unsigned value to globally enable/disable scan 1748 * 1 - Enable, 0 - Disable. 1749 */ 1750 QCA_WLAN_VENDOR_ATTR_CONFIG_SCAN_ENABLE = 51, 1751 1752 /* 8-bit unsigned value to set the total beacon miss count 1753 * This parameter will set the total beacon miss count. 1754 */ 1755 QCA_WLAN_VENDOR_ATTR_CONFIG_TOTAL_BEACON_MISS_COUNT = 52, 1756 1757 /* Unsigned 32-bit value to configure the number of continuous 1758 * Beacon Miss which shall be used by the firmware to penalize 1759 * the RSSI for BTC. 1760 */ 1761 QCA_WLAN_VENDOR_ATTR_CONFIG_PENALIZE_AFTER_NCONS_BEACON_MISS_BTC = 53, 1762 1763 /* 8-bit unsigned value to configure the driver and below layers to 1764 * enable/disable all FILS features. 1765 * 0-enable, 1-disable 1766 */ 1767 QCA_WLAN_VENDOR_ATTR_CONFIG_DISABLE_FILS = 54, 1768 1769 /* 16-bit unsigned value to configure the level of WLAN latency 1770 * module. See enum qca_wlan_vendor_attr_config_latency_level. 1771 */ 1772 QCA_WLAN_VENDOR_ATTR_CONFIG_LATENCY_LEVEL = 55, 1773 1774 /* 8-bit unsigned value indicating the driver to use the RSNE as-is from 1775 * the connect interface. Exclusively used for the scenarios where the 1776 * device is used as a test bed device with special functionality and 1777 * not recommended for production. This helps driver to not validate the 1778 * RSNE passed from user space and thus allow arbitrary IE data to be 1779 * used for testing purposes. 1780 * 1-enable, 0-disable. 1781 * Applications set/reset this configuration. If not reset, this 1782 * parameter remains in use until the driver is unloaded. 1783 */ 1784 QCA_WLAN_VENDOR_ATTR_CONFIG_RSN_IE = 56, 1785 1786 /* 8-bit unsigned value to trigger green Tx power saving. 1787 * 1-Enable, 0-Disable 1788 */ 1789 QCA_WLAN_VENDOR_ATTR_CONFIG_GTX = 57, 1790 1791 /* keep last */ 1792 QCA_WLAN_VENDOR_ATTR_CONFIG_AFTER_LAST, 1793 QCA_WLAN_VENDOR_ATTR_CONFIG_MAX = 1794 QCA_WLAN_VENDOR_ATTR_CONFIG_AFTER_LAST - 1, 1795 }; 1796 1797 /** 1798 * enum qca_wlan_vendor_attr_sap_config - Parameters for AP configuration 1799 */ 1800 enum qca_wlan_vendor_attr_sap_config { 1801 QCA_WLAN_VENDOR_ATTR_SAP_CONFIG_INVALID = 0, 1802 /* 1 - reserved for QCA */ 1803 /* List of frequencies on which AP is expected to operate. 1804 * This is irrespective of ACS configuration. This list is a priority 1805 * based one and is looked for before the AP is created to ensure the 1806 * best concurrency sessions (avoid MCC and use DBS/SCC) co-exist in 1807 * the system. 1808 */ 1809 QCA_WLAN_VENDOR_ATTR_SAP_MANDATORY_FREQUENCY_LIST = 2, 1810 1811 QCA_WLAN_VENDOR_ATTR_SAP_CONFIG_AFTER_LAST, 1812 QCA_WLAN_VENDOR_ATTR_SAP_CONFIG_MAX = 1813 QCA_WLAN_VENDOR_ATTR_SAP_CONFIG_AFTER_LAST - 1, 1814 }; 1815 1816 /** 1817 * enum qca_wlan_vendor_attr_sap_conditional_chan_switch - Parameters for AP 1818 * conditional channel switch 1819 */ 1820 enum qca_wlan_vendor_attr_sap_conditional_chan_switch { 1821 QCA_WLAN_VENDOR_ATTR_SAP_CONDITIONAL_CHAN_SWITCH_INVALID = 0, 1822 /* Priority based frequency list (an array of u32 values in host byte 1823 * order) 1824 */ 1825 QCA_WLAN_VENDOR_ATTR_SAP_CONDITIONAL_CHAN_SWITCH_FREQ_LIST = 1, 1826 /* Status of the conditional switch (u32). 1827 * 0: Success, Non-zero: Failure 1828 */ 1829 QCA_WLAN_VENDOR_ATTR_SAP_CONDITIONAL_CHAN_SWITCH_STATUS = 2, 1830 1831 QCA_WLAN_VENDOR_ATTR_SAP_CONDITIONAL_CHAN_SWITCH_AFTER_LAST, 1832 QCA_WLAN_VENDOR_ATTR_SAP_CONDITIONAL_CHAN_SWITCH_MAX = 1833 QCA_WLAN_VENDOR_ATTR_SAP_CONDITIONAL_CHAN_SWITCH_AFTER_LAST - 1, 1834 }; 1835 1836 /** 1837 * enum qca_wlan_gpio_attr - Parameters for GPIO configuration 1838 */ 1839 enum qca_wlan_gpio_attr { 1840 QCA_WLAN_VENDOR_ATTR_GPIO_PARAM_INVALID = 0, 1841 /* Unsigned 32-bit attribute for GPIO command */ 1842 QCA_WLAN_VENDOR_ATTR_GPIO_PARAM_COMMAND, 1843 /* Unsigned 32-bit attribute for GPIO PIN number to configure */ 1844 QCA_WLAN_VENDOR_ATTR_GPIO_PARAM_PINNUM, 1845 /* Unsigned 32-bit attribute for GPIO value to configure */ 1846 QCA_WLAN_VENDOR_ATTR_GPIO_PARAM_VALUE, 1847 /* Unsigned 32-bit attribute for GPIO pull type */ 1848 QCA_WLAN_VENDOR_ATTR_GPIO_PARAM_PULL_TYPE, 1849 /* Unsigned 32-bit attribute for GPIO interrupt mode */ 1850 QCA_WLAN_VENDOR_ATTR_GPIO_PARAM_INTR_MODE, 1851 1852 /* keep last */ 1853 QCA_WLAN_VENDOR_ATTR_GPIO_PARAM_LAST, 1854 QCA_WLAN_VENDOR_ATTR_GPIO_PARAM_MAX = 1855 QCA_WLAN_VENDOR_ATTR_GPIO_PARAM_LAST - 1 1856 }; 1857 1858 /** 1859 * qca_wlan_set_qdepth_thresh_attr - Parameters for setting 1860 * MSDUQ depth threshold per peer per tid in the target 1861 * 1862 * Associated Vendor Command: 1863 * QCA_NL80211_VENDOR_SUBCMD_SET_QDEPTH_THRESH 1864 */ 1865 enum qca_wlan_set_qdepth_thresh_attr { 1866 QCA_WLAN_VENDOR_ATTR_QDEPTH_THRESH_INVALID = 0, 1867 /* 6-byte MAC address */ 1868 QCA_WLAN_VENDOR_ATTR_QDEPTH_THRESH_MAC_ADDR, 1869 /* Unsigned 32-bit attribute for holding the TID */ 1870 QCA_WLAN_VENDOR_ATTR_QDEPTH_THRESH_TID, 1871 /* Unsigned 32-bit attribute for holding the update mask 1872 * bit 0 - Update high priority msdu qdepth threshold 1873 * bit 1 - Update low priority msdu qdepth threshold 1874 * bit 2 - Update UDP msdu qdepth threshold 1875 * bit 3 - Update Non UDP msdu qdepth threshold 1876 * rest of bits are reserved 1877 */ 1878 QCA_WLAN_VENDOR_ATTR_QDEPTH_THRESH_UPDATE_MASK, 1879 /* Unsigned 32-bit attribute for holding the threshold value */ 1880 QCA_WLAN_VENDOR_ATTR_QDEPTH_THRESH_VALUE, 1881 1882 /* keep last */ 1883 QCA_WLAN_VENDOR_ATTR_QDEPTH_THRESH_LAST, 1884 QCA_WLAN_VENDOR_ATTR_QDEPTH_THRESH_MAX = 1885 QCA_WLAN_VENDOR_ATTR_QDEPTH_THRESH_LAST - 1, 1886 }; 1887 1888 /** 1889 * enum qca_wlan_vendor_attr_get_hw_capability - Wi-Fi hardware capability 1890 */ 1891 enum qca_wlan_vendor_attr_get_hw_capability { 1892 QCA_WLAN_VENDOR_ATTR_HW_CAPABILITY_INVALID, 1893 /* Antenna isolation 1894 * An attribute used in the response. 1895 * The content of this attribute is encoded in a byte array. Each byte 1896 * value is an antenna isolation value. The array length is the number 1897 * of antennas. 1898 */ 1899 QCA_WLAN_VENDOR_ATTR_ANTENNA_ISOLATION, 1900 /* Request HW capability 1901 * An attribute used in the request. 1902 * The content of this attribute is a u32 array for one or more of 1903 * hardware capabilities (attribute IDs) that are being requested. Each 1904 * u32 value has a value from this 1905 * enum qca_wlan_vendor_attr_get_hw_capability 1906 * identifying which capabilities are requested. 1907 */ 1908 QCA_WLAN_VENDOR_ATTR_GET_HW_CAPABILITY, 1909 1910 /* keep last */ 1911 QCA_WLAN_VENDOR_ATTR_HW_CAPABILITY_AFTER_LAST, 1912 QCA_WLAN_VENDOR_ATTR_HW_CAPABILITY_MAX = 1913 QCA_WLAN_VENDOR_ATTR_HW_CAPABILITY_AFTER_LAST - 1, 1914 }; 1915 1916 /** 1917 * enum qca_wlan_vendor_attr_ll_stats_ext - Attributes for MAC layer monitoring 1918 * offload which is an extension for LL_STATS. 1919 * @QCA_WLAN_VENDOR_ATTR_LL_STATS_CFG_PERIOD: Monitoring period. Unit in ms. 1920 * If MAC counters do not exceed the threshold, FW will report monitored 1921 * link layer counters periodically as this setting. The first report is 1922 * always triggered by this timer. 1923 * @QCA_WLAN_VENDOR_ATTR_LL_STATS_CFG_THRESHOLD: It is a percentage (1-99). 1924 * For each MAC layer counter, FW holds two copies. One is the current value. 1925 * The other is the last report. Once a current counter's increment is larger 1926 * than the threshold, FW will indicate that counter to host even if the 1927 * monitoring timer does not expire. 1928 * @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_PEER_PS_CHG: Peer STA power state change 1929 * @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_TID: TID of MSDU 1930 * @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_NUM_MSDU: Count of MSDU with the same 1931 * failure code. 1932 * @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_TX_STATUS: TX failure code 1933 * 1: TX packet discarded 1934 * 2: No ACK 1935 * 3: Postpone 1936 * @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_PEER_MAC_ADDRESS: peer MAC address 1937 * @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_PEER_PS_STATE: Peer STA current state 1938 * @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_GLOBAL: Global threshold. 1939 * Threshold for all monitored parameters. If per counter dedicated threshold 1940 * is not enabled, this threshold will take effect. 1941 * @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_EVENT_MODE: Indicate what triggers this 1942 * event, PERORID_TIMEOUT == 1, THRESH_EXCEED == 0. 1943 * @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_IFACE_ID: interface ID 1944 * @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_PEER_ID: peer ID 1945 * @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_TX_BITMAP: bitmap for TX counters 1946 * Bit0: TX counter unit in MSDU 1947 * Bit1: TX counter unit in MPDU 1948 * Bit2: TX counter unit in PPDU 1949 * Bit3: TX counter unit in byte 1950 * Bit4: Dropped MSDUs 1951 * Bit5: Dropped Bytes 1952 * Bit6: MPDU retry counter 1953 * Bit7: MPDU failure counter 1954 * Bit8: PPDU failure counter 1955 * Bit9: MPDU aggregation counter 1956 * Bit10: MCS counter for ACKed MPDUs 1957 * Bit11: MCS counter for Failed MPDUs 1958 * Bit12: TX Delay counter 1959 * @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_RX_BITMAP: bitmap for RX counters 1960 * Bit0: MAC RX counter unit in MPDU 1961 * Bit1: MAC RX counter unit in byte 1962 * Bit2: PHY RX counter unit in PPDU 1963 * Bit3: PHY RX counter unit in byte 1964 * Bit4: Disorder counter 1965 * Bit5: Retry counter 1966 * Bit6: Duplication counter 1967 * Bit7: Discard counter 1968 * Bit8: MPDU aggregation size counter 1969 * Bit9: MCS counter 1970 * Bit10: Peer STA power state change (wake to sleep) counter 1971 * Bit11: Peer STA power save counter, total time in PS mode 1972 * Bit12: Probe request counter 1973 * Bit13: Other management frames counter 1974 * @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_CCA_BSS_BITMAP: bitmap for CCA 1975 * Bit0: Idle time 1976 * Bit1: TX time 1977 * Bit2: time RX in current bss 1978 * Bit3: Out of current bss time 1979 * Bit4: Wireless medium busy time 1980 * Bit5: RX in bad condition time 1981 * Bit6: TX in bad condition time 1982 * Bit7: time wlan card not available 1983 * @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_SIGNAL_BITMAP: bitmap for signal 1984 * Bit0: Per channel SNR counter 1985 * Bit1: Per channel noise floor counter 1986 * @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_PEER_NUM: number of peers 1987 * @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_CHANNEL_NUM: number of channels 1988 * @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_PEER_AC_RX_NUM: number of RX stats 1989 * @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_CCA_BSS: per channel BSS CCA stats 1990 * @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_PEER: container for per PEER stats 1991 * @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_TX_MSDU: Number of total TX MSDUs 1992 * @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_TX_MPDU: Number of total TX MPDUs 1993 * @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_TX_PPDU: Number of total TX PPDUs 1994 * @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_TX_BYTES: bytes of TX data 1995 * @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_TX_DROP: Number of dropped TX packets 1996 * @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_TX_DROP_BYTES: Bytes dropped 1997 * @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_TX_RETRY: waiting time without an ACK 1998 * @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_TX_NO_ACK: number of MPDU not-ACKed 1999 * @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_TX_NO_BACK: number of PPDU not-ACKed 2000 * @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_TX_AGGR_NUM: 2001 * aggregation stats buffer length 2002 * @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_TX_SUCC_MCS_NUM: length of mcs stats 2003 * buffer for ACKed MPDUs. 2004 * @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_TX_FAIL_MCS_NUM: length of mcs stats 2005 * buffer for failed MPDUs. 2006 * @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_DELAY_ARRAY_SIZE: 2007 * length of delay stats array. 2008 * @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_TX_AGGR: TX aggregation stats 2009 * @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_TX_SUCC_MCS: MCS stats for ACKed MPDUs 2010 * @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_TX_FAIL_MCS: MCS stats for failed MPDUs 2011 * @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_TX_DELAY: tx delay stats 2012 * @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_RX_MPDU: MPDUs received 2013 * @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_RX_MPDU_BYTES: bytes received 2014 * @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_RX_PPDU: PPDU received 2015 * @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_RX_PPDU_BYTES: PPDU bytes received 2016 * @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_RX_MPDU_LOST: packets lost 2017 * @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_RX_MPDU_RETRY: number of RX packets 2018 * flagged as retransmissions 2019 * @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_RX_MPDU_DUP: number of RX packets 2020 * flagged as duplicated 2021 * @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_RX_MPDU_DISCARD: number of RX 2022 * packets discarded 2023 * @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_RX_AGGR_NUM: length of RX aggregation 2024 * stats buffer. 2025 * @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_RX_MCS_NUM: length of RX mcs 2026 * stats buffer. 2027 * @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_RX_MCS: RX mcs stats buffer 2028 * @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_RX_AGGR: aggregation stats buffer 2029 * @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_PEER_PS_TIMES: times STAs go to sleep 2030 * @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_PEER_PS_DURATION: STAs' total sleep time 2031 * @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_RX_PROBE_REQ: number of probe 2032 * requests received 2033 * @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_RX_MGMT: number of other mgmt 2034 * frames received 2035 * @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_IDLE_TIME: Percentage of idle time 2036 * there is no TX, nor RX, nor interference. 2037 * @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_TX_TIME: percentage of time 2038 * transmitting packets. 2039 * @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_RX_TIME: percentage of time 2040 * for receiving. 2041 * @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_RX_BUSY: percentage of time 2042 * interference detected. 2043 * @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_RX_BAD: percentage of time 2044 * receiving packets with errors. 2045 * @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_TX_BAD: percentage of time 2046 * TX no-ACK. 2047 * @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_NO_AVAIL: percentage of time 2048 * the chip is unable to work in normal conditions. 2049 * @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_IN_BSS_TIME: percentage of time 2050 * receiving packets in current BSS. 2051 * @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_OUT_BSS_TIME: percentage of time 2052 * receiving packets not in current BSS. 2053 * @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_PEER_ANT_NUM: number of antennas 2054 * @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_PEER_SIGNAL: 2055 * This is a container for per antenna signal stats. 2056 * @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_ANT_SNR: per antenna SNR value 2057 * @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_ANT_NF: per antenna NF value 2058 * @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_IFACE_RSSI_BEACON: RSSI of beacon 2059 * @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_IFACE_SNR_BEACON: SNR of beacon 2060 * @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_REPORT_TIME: u64 2061 * Absolute timestamp from 1970/1/1, unit in ms. After receiving the 2062 * message, user layer APP could call gettimeofday to get another 2063 * timestamp and calculate transfer delay for the message. 2064 * @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_MEASUREMENT_TIME: u32 2065 * Real period for this measurement, unit in us. 2066 */ 2067 enum qca_wlan_vendor_attr_ll_stats_ext { 2068 QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_INVALID = 0, 2069 2070 /* Attributes for configurations */ 2071 QCA_WLAN_VENDOR_ATTR_LL_STATS_CFG_PERIOD, 2072 QCA_WLAN_VENDOR_ATTR_LL_STATS_CFG_THRESHOLD, 2073 2074 /* Peer STA power state change */ 2075 QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_PEER_PS_CHG, 2076 2077 /* TX failure event */ 2078 QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_TID, 2079 QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_NUM_MSDU, 2080 QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_TX_STATUS, 2081 2082 QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_PEER_PS_STATE, 2083 QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_PEER_MAC_ADDRESS, 2084 2085 /* MAC counters */ 2086 QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_GLOBAL, 2087 QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_EVENT_MODE, 2088 QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_IFACE_ID, 2089 QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_PEER_ID, 2090 QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_TX_BITMAP, 2091 QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_RX_BITMAP, 2092 QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_CCA_BSS_BITMAP, 2093 QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_SIGNAL_BITMAP, 2094 QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_PEER_NUM, 2095 QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_CHANNEL_NUM, 2096 QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_CCA_BSS, 2097 QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_PEER, 2098 2099 /* Sub-attributes for PEER_AC_TX */ 2100 QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_TX_MSDU, 2101 QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_TX_MPDU, 2102 QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_TX_PPDU, 2103 QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_TX_BYTES, 2104 QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_TX_DROP, 2105 QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_TX_DROP_BYTES, 2106 QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_TX_RETRY, 2107 QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_TX_NO_ACK, 2108 QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_TX_NO_BACK, 2109 QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_TX_AGGR_NUM, 2110 QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_TX_SUCC_MCS_NUM, 2111 QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_TX_FAIL_MCS_NUM, 2112 QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_TX_AGGR, 2113 QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_TX_SUCC_MCS, 2114 QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_TX_FAIL_MCS, 2115 QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_DELAY_ARRAY_SIZE, 2116 QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_TX_DELAY, 2117 2118 /* Sub-attributes for PEER_AC_RX */ 2119 QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_RX_MPDU, 2120 QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_RX_MPDU_BYTES, 2121 QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_RX_PPDU, 2122 QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_RX_PPDU_BYTES, 2123 QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_RX_MPDU_LOST, 2124 QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_RX_MPDU_RETRY, 2125 QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_RX_MPDU_DUP, 2126 QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_RX_MPDU_DISCARD, 2127 QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_RX_AGGR_NUM, 2128 QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_RX_MCS_NUM, 2129 QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_RX_MCS, 2130 QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_RX_AGGR, 2131 QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_PEER_PS_TIMES, 2132 QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_PEER_PS_DURATION, 2133 QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_RX_PROBE_REQ, 2134 QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_RX_MGMT, 2135 2136 /* Sub-attributes for CCA_BSS */ 2137 QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_IDLE_TIME, 2138 QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_TX_TIME, 2139 QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_RX_TIME, 2140 QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_RX_BUSY, 2141 QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_RX_BAD, 2142 QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_TX_BAD, 2143 QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_NO_AVAIL, 2144 2145 /* sub-attribute for BSS_RX_TIME */ 2146 QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_IN_BSS_TIME, 2147 QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_OUT_BSS_TIME, 2148 2149 /* Sub-attributes for PEER_SIGNAL */ 2150 QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_PEER_ANT_NUM, 2151 QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_PEER_SIGNAL, 2152 QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_ANT_SNR, 2153 QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_ANT_NF, 2154 2155 /* Sub-attributes for IFACE_BSS */ 2156 QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_IFACE_RSSI_BEACON, 2157 QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_IFACE_SNR_BEACON, 2158 2159 QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_REPORT_TIME, 2160 QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_MEASUREMENT_TIME, 2161 2162 QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_LAST, 2163 QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_MAX = 2164 QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_LAST - 1 2165 }; 2166 2167 /* Attributes for FTM commands and events */ 2168 2169 /** 2170 * enum qca_wlan_vendor_attr_loc_capa - Indoor location capabilities 2171 * 2172 * @QCA_WLAN_VENDOR_ATTR_LOC_CAPA_FLAGS: Various flags. See 2173 * enum qca_wlan_vendor_attr_loc_capa_flags. 2174 * @QCA_WLAN_VENDOR_ATTR_FTM_CAPA_MAX_NUM_SESSIONS: Maximum number 2175 * of measurement sessions that can run concurrently. 2176 * Default is one session (no session concurrency). 2177 * @QCA_WLAN_VENDOR_ATTR_FTM_CAPA_MAX_NUM_PEERS: The total number of unique 2178 * peers that are supported in running sessions. For example, 2179 * if the value is 8 and maximum number of sessions is 2, you can 2180 * have one session with 8 unique peers, or 2 sessions with 4 unique 2181 * peers each, and so on. 2182 * @QCA_WLAN_VENDOR_ATTR_FTM_CAPA_MAX_NUM_BURSTS_EXP: Maximum number 2183 * of bursts per peer, as an exponent (2^value). Default is 0, 2184 * meaning no multi-burst support. 2185 * @QCA_WLAN_VENDOR_ATTR_FTM_CAPA_MAX_MEAS_PER_BURST: Maximum number 2186 * of measurement exchanges allowed in a single burst. 2187 * @QCA_WLAN_VENDOR_ATTR_AOA_CAPA_SUPPORTED_TYPES: Supported AOA measurement 2188 * types. A bit mask (unsigned 32 bit value), each bit corresponds 2189 * to an AOA type as defined by enum qca_vendor_attr_aoa_type. 2190 */ 2191 enum qca_wlan_vendor_attr_loc_capa { 2192 QCA_WLAN_VENDOR_ATTR_LOC_CAPA_INVALID, 2193 QCA_WLAN_VENDOR_ATTR_LOC_CAPA_FLAGS, 2194 QCA_WLAN_VENDOR_ATTR_FTM_CAPA_MAX_NUM_SESSIONS, 2195 QCA_WLAN_VENDOR_ATTR_FTM_CAPA_MAX_NUM_PEERS, 2196 QCA_WLAN_VENDOR_ATTR_FTM_CAPA_MAX_NUM_BURSTS_EXP, 2197 QCA_WLAN_VENDOR_ATTR_FTM_CAPA_MAX_MEAS_PER_BURST, 2198 QCA_WLAN_VENDOR_ATTR_AOA_CAPA_SUPPORTED_TYPES, 2199 /* keep last */ 2200 QCA_WLAN_VENDOR_ATTR_LOC_CAPA_AFTER_LAST, 2201 QCA_WLAN_VENDOR_ATTR_LOC_CAPA_MAX = 2202 QCA_WLAN_VENDOR_ATTR_LOC_CAPA_AFTER_LAST - 1, 2203 }; 2204 2205 /** 2206 * enum qca_wlan_vendor_attr_loc_capa_flags: Indoor location capability flags 2207 * 2208 * @QCA_WLAN_VENDOR_ATTR_LOC_CAPA_FLAG_FTM_RESPONDER: Set if driver 2209 * can be configured as an FTM responder (for example, an AP that 2210 * services FTM requests). QCA_NL80211_VENDOR_SUBCMD_FTM_CFG_RESPONDER 2211 * will be supported if set. 2212 * @QCA_WLAN_VENDOR_ATTR_LOC_CAPA_FLAG_FTM_INITIATOR: Set if driver 2213 * can run FTM sessions. QCA_NL80211_VENDOR_SUBCMD_FTM_START_SESSION 2214 * will be supported if set. 2215 * @QCA_WLAN_VENDOR_ATTR_LOC_CAPA_FLAG_ASAP: Set if FTM responder 2216 * supports immediate (ASAP) response. 2217 * @QCA_WLAN_VENDOR_ATTR_LOC_CAPA_FLAG_AOA: Set if driver supports standalone 2218 * AOA measurement using QCA_NL80211_VENDOR_SUBCMD_AOA_MEAS. 2219 * @QCA_WLAN_VENDOR_ATTR_LOC_CAPA_FLAG_AOA_IN_FTM: Set if driver supports 2220 * requesting AOA measurements as part of an FTM session. 2221 */ 2222 enum qca_wlan_vendor_attr_loc_capa_flags { 2223 QCA_WLAN_VENDOR_ATTR_LOC_CAPA_FLAG_FTM_RESPONDER = 1 << 0, 2224 QCA_WLAN_VENDOR_ATTR_LOC_CAPA_FLAG_FTM_INITIATOR = 1 << 1, 2225 QCA_WLAN_VENDOR_ATTR_LOC_CAPA_FLAG_ASAP = 1 << 2, 2226 QCA_WLAN_VENDOR_ATTR_LOC_CAPA_FLAG_AOA = 1 << 3, 2227 QCA_WLAN_VENDOR_ATTR_LOC_CAPA_FLAG_AOA_IN_FTM = 1 << 4, 2228 }; 2229 2230 /** 2231 * enum qca_wlan_vendor_attr_ftm_peer_info: Information about 2232 * a single peer in a measurement session. 2233 * 2234 * @QCA_WLAN_VENDOR_ATTR_FTM_PEER_MAC_ADDR: The MAC address of the peer. 2235 * @QCA_WLAN_VENDOR_ATTR_FTM_PEER_MEAS_FLAGS: Various flags related 2236 * to measurement. See enum qca_wlan_vendor_attr_ftm_peer_meas_flags. 2237 * @QCA_WLAN_VENDOR_ATTR_FTM_PEER_MEAS_PARAMS: Nested attribute of 2238 * FTM measurement parameters, as specified by IEEE P802.11-REVmc/D7.0 2239 * 9.4.2.167. See enum qca_wlan_vendor_attr_ftm_meas_param for 2240 * list of supported attributes. 2241 * @QCA_WLAN_VENDOR_ATTR_FTM_PEER_SECURE_TOKEN_ID: Initial token ID for 2242 * secure measurement. 2243 * @QCA_WLAN_VENDOR_ATTR_FTM_PEER_AOA_BURST_PERIOD: Request AOA 2244 * measurement every <value> bursts. If 0 or not specified, 2245 * AOA measurements will be disabled for this peer. 2246 * @QCA_WLAN_VENDOR_ATTR_FTM_PEER_FREQ: Frequency in MHz where 2247 * the measurement frames are exchanged. Optional; if not 2248 * specified, try to locate the peer in the kernel scan 2249 * results cache and use frequency from there. 2250 */ 2251 enum qca_wlan_vendor_attr_ftm_peer_info { 2252 QCA_WLAN_VENDOR_ATTR_FTM_PEER_INVALID, 2253 QCA_WLAN_VENDOR_ATTR_FTM_PEER_MAC_ADDR, 2254 QCA_WLAN_VENDOR_ATTR_FTM_PEER_MEAS_FLAGS, 2255 QCA_WLAN_VENDOR_ATTR_FTM_PEER_MEAS_PARAMS, 2256 QCA_WLAN_VENDOR_ATTR_FTM_PEER_SECURE_TOKEN_ID, 2257 QCA_WLAN_VENDOR_ATTR_FTM_PEER_AOA_BURST_PERIOD, 2258 QCA_WLAN_VENDOR_ATTR_FTM_PEER_FREQ, 2259 /* keep last */ 2260 QCA_WLAN_VENDOR_ATTR_FTM_PEER_AFTER_LAST, 2261 QCA_WLAN_VENDOR_ATTR_FTM_PEER_MAX = 2262 QCA_WLAN_VENDOR_ATTR_FTM_PEER_AFTER_LAST - 1, 2263 }; 2264 2265 /** 2266 * enum qca_wlan_vendor_attr_ftm_peer_meas_flags: Measurement request flags, 2267 * per-peer 2268 * 2269 * @QCA_WLAN_VENDOR_ATTR_FTM_PEER_MEAS_FLAG_ASAP: If set, request 2270 * immediate (ASAP) response from peer. 2271 * @QCA_WLAN_VENDOR_ATTR_FTM_PEER_MEAS_FLAG_LCI: If set, request 2272 * LCI report from peer. The LCI report includes the absolute 2273 * location of the peer in "official" coordinates (similar to GPS). 2274 * See IEEE P802.11-REVmc/D7.0, 11.24.6.7 for more information. 2275 * @QCA_WLAN_VENDOR_ATTR_FTM_PEER_MEAS_FLAG_LCR: If set, request 2276 * Location civic report from peer. The LCR includes the location 2277 * of the peer in free-form format. See IEEE P802.11-REVmc/D7.0, 2278 * 11.24.6.7 for more information. 2279 * @QCA_WLAN_VENDOR_ATTR_FTM_PEER_MEAS_FLAG_SECURE: If set, 2280 * request a secure measurement. 2281 * QCA_WLAN_VENDOR_ATTR_FTM_PEER_SECURE_TOKEN_ID must also be provided. 2282 */ 2283 enum qca_wlan_vendor_attr_ftm_peer_meas_flags { 2284 QCA_WLAN_VENDOR_ATTR_FTM_PEER_MEAS_FLAG_ASAP = 1 << 0, 2285 QCA_WLAN_VENDOR_ATTR_FTM_PEER_MEAS_FLAG_LCI = 1 << 1, 2286 QCA_WLAN_VENDOR_ATTR_FTM_PEER_MEAS_FLAG_LCR = 1 << 2, 2287 QCA_WLAN_VENDOR_ATTR_FTM_PEER_MEAS_FLAG_SECURE = 1 << 3, 2288 }; 2289 2290 /** 2291 * enum qca_wlan_vendor_attr_ftm_meas_param: Measurement parameters 2292 * 2293 * @QCA_WLAN_VENDOR_ATTR_FTM_PARAM_MEAS_PER_BURST: Number of measurements 2294 * to perform in a single burst. 2295 * @QCA_WLAN_VENDOR_ATTR_FTM_PARAM_NUM_BURSTS_EXP: Number of bursts to 2296 * perform, specified as an exponent (2^value). 2297 * @QCA_WLAN_VENDOR_ATTR_FTM_PARAM_BURST_DURATION: Duration of burst 2298 * instance, as specified in IEEE P802.11-REVmc/D7.0, 9.4.2.167. 2299 * @QCA_WLAN_VENDOR_ATTR_FTM_PARAM_BURST_PERIOD: Time between bursts, 2300 * as specified in IEEE P802.11-REVmc/D7.0, 9.4.2.167. Must 2301 * be larger than QCA_WLAN_VENDOR_ATTR_FTM_PARAM_BURST_DURATION. 2302 */ 2303 enum qca_wlan_vendor_attr_ftm_meas_param { 2304 QCA_WLAN_VENDOR_ATTR_FTM_PARAM_INVALID, 2305 QCA_WLAN_VENDOR_ATTR_FTM_PARAM_MEAS_PER_BURST, 2306 QCA_WLAN_VENDOR_ATTR_FTM_PARAM_NUM_BURSTS_EXP, 2307 QCA_WLAN_VENDOR_ATTR_FTM_PARAM_BURST_DURATION, 2308 QCA_WLAN_VENDOR_ATTR_FTM_PARAM_BURST_PERIOD, 2309 /* keep last */ 2310 QCA_WLAN_VENDOR_ATTR_FTM_PARAM_AFTER_LAST, 2311 QCA_WLAN_VENDOR_ATTR_FTM_PARAM_MAX = 2312 QCA_WLAN_VENDOR_ATTR_FTM_PARAM_AFTER_LAST - 1, 2313 }; 2314 2315 /** 2316 * enum qca_wlan_vendor_attr_ftm_peer_result: Per-peer results 2317 * 2318 * @QCA_WLAN_VENDOR_ATTR_FTM_PEER_RES_MAC_ADDR: MAC address of the reported 2319 * peer. 2320 * @QCA_WLAN_VENDOR_ATTR_FTM_PEER_RES_STATUS: Status of measurement 2321 * request for this peer. 2322 * See enum qca_wlan_vendor_attr_ftm_peer_result_status. 2323 * @QCA_WLAN_VENDOR_ATTR_FTM_PEER_RES_FLAGS: Various flags related 2324 * to measurement results for this peer. 2325 * See enum qca_wlan_vendor_attr_ftm_peer_result_flags. 2326 * @QCA_WLAN_VENDOR_ATTR_FTM_PEER_RES_VALUE_SECONDS: Specified when 2327 * request failed and peer requested not to send an additional request 2328 * for this number of seconds. 2329 * @QCA_WLAN_VENDOR_ATTR_FTM_PEER_RES_LCI: LCI report when received 2330 * from peer. In the format specified by IEEE P802.11-REVmc/D7.0, 2331 * 9.4.2.22.10. 2332 * @QCA_WLAN_VENDOR_ATTR_FTM_PEER_RES_LCR: Location civic report when 2333 * received from peer. In the format specified by IEEE P802.11-REVmc/D7.0, 2334 * 9.4.2.22.13. 2335 * @QCA_WLAN_VENDOR_ATTR_FTM_PEER_RES_MEAS_PARAMS: Reported when peer 2336 * overridden some measurement request parameters. See 2337 * enum qca_wlan_vendor_attr_ftm_meas_param. 2338 * @QCA_WLAN_VENDOR_ATTR_FTM_PEER_RES_AOA_MEAS: AOA measurement 2339 * for this peer. Same contents as @QCA_WLAN_VENDOR_ATTR_AOA_MEAS_RESULT. 2340 * @QCA_WLAN_VENDOR_ATTR_FTM_PEER_RES_MEAS: Array of measurement 2341 * results. Each entry is a nested attribute defined 2342 * by enum qca_wlan_vendor_attr_ftm_meas. 2343 */ 2344 enum qca_wlan_vendor_attr_ftm_peer_result { 2345 QCA_WLAN_VENDOR_ATTR_FTM_PEER_RES_INVALID, 2346 QCA_WLAN_VENDOR_ATTR_FTM_PEER_RES_MAC_ADDR, 2347 QCA_WLAN_VENDOR_ATTR_FTM_PEER_RES_STATUS, 2348 QCA_WLAN_VENDOR_ATTR_FTM_PEER_RES_FLAGS, 2349 QCA_WLAN_VENDOR_ATTR_FTM_PEER_RES_VALUE_SECONDS, 2350 QCA_WLAN_VENDOR_ATTR_FTM_PEER_RES_LCI, 2351 QCA_WLAN_VENDOR_ATTR_FTM_PEER_RES_LCR, 2352 QCA_WLAN_VENDOR_ATTR_FTM_PEER_RES_MEAS_PARAMS, 2353 QCA_WLAN_VENDOR_ATTR_FTM_PEER_RES_AOA_MEAS, 2354 QCA_WLAN_VENDOR_ATTR_FTM_PEER_RES_MEAS, 2355 /* keep last */ 2356 QCA_WLAN_VENDOR_ATTR_FTM_PEER_RES_AFTER_LAST, 2357 QCA_WLAN_VENDOR_ATTR_FTM_PEER_RES_MAX = 2358 QCA_WLAN_VENDOR_ATTR_FTM_PEER_RES_AFTER_LAST - 1, 2359 }; 2360 2361 /** 2362 * enum qca_wlan_vendor_attr_ftm_peer_result_status 2363 * 2364 * @QCA_WLAN_VENDOR_ATTR_FTM_PEER_RES_STATUS_OK: Request sent ok and results 2365 * will be provided. Peer may have overridden some measurement parameters, 2366 * in which case overridden parameters will be report by 2367 * QCA_WLAN_VENDOR_ATTR_FTM_PEER_RES_MEAS_PARAM attribute. 2368 * @QCA_WLAN_VENDOR_ATTR_FTM_PEER_RES_STATUS_INCAPABLE: Peer is incapable 2369 * of performing the measurement request. No more results will be sent 2370 * for this peer in this session. 2371 * @QCA_WLAN_VENDOR_ATTR_FTM_PEER_RES_STATUS_FAILED: Peer reported request 2372 * failed, and requested not to send an additional request for number 2373 * of seconds specified by QCA_WLAN_VENDOR_ATTR_FTM_PEER_RES_VALUE_SECONDS 2374 * attribute. 2375 * @QCA_WLAN_VENDOR_ATTR_FTM_PEER_RES_STATUS_INVALID: Request validation 2376 * failed. Request was not sent over the air. 2377 */ 2378 enum qca_wlan_vendor_attr_ftm_peer_result_status { 2379 QCA_WLAN_VENDOR_ATTR_FTM_PEER_RES_STATUS_OK, 2380 QCA_WLAN_VENDOR_ATTR_FTM_PEER_RES_STATUS_INCAPABLE, 2381 QCA_WLAN_VENDOR_ATTR_FTM_PEER_RES_STATUS_FAILED, 2382 QCA_WLAN_VENDOR_ATTR_FTM_PEER_RES_STATUS_INVALID, 2383 }; 2384 2385 /** 2386 * enum qca_wlan_vendor_attr_ftm_peer_result_flags: Various flags 2387 * for measurement result, per-peer 2388 * 2389 * @QCA_WLAN_VENDOR_ATTR_FTM_PEER_RES_FLAG_DONE: If set, 2390 * measurement completed for this peer. No more results will be reported 2391 * for this peer in this session. 2392 */ 2393 enum qca_wlan_vendor_attr_ftm_peer_result_flags { 2394 QCA_WLAN_VENDOR_ATTR_FTM_PEER_RES_FLAG_DONE = 1 << 0, 2395 }; 2396 2397 /** 2398 * enum qca_vendor_attr_loc_session_status: Session completion status code 2399 * 2400 * @QCA_WLAN_VENDOR_ATTR_LOC_SESSION_STATUS_OK: Session completed 2401 * successfully. 2402 * @QCA_WLAN_VENDOR_ATTR_LOC_SESSION_STATUS_ABORTED: Session aborted 2403 * by request. 2404 * @QCA_WLAN_VENDOR_ATTR_LOC_SESSION_STATUS_INVALID: Session request 2405 * was invalid and was not started. 2406 * @QCA_WLAN_VENDOR_ATTR_LOC_SESSION_STATUS_FAILED: Session had an error 2407 * and did not complete normally (for example out of resources). 2408 */ 2409 enum qca_vendor_attr_loc_session_status { 2410 QCA_WLAN_VENDOR_ATTR_LOC_SESSION_STATUS_OK, 2411 QCA_WLAN_VENDOR_ATTR_LOC_SESSION_STATUS_ABORTED, 2412 QCA_WLAN_VENDOR_ATTR_LOC_SESSION_STATUS_INVALID, 2413 QCA_WLAN_VENDOR_ATTR_LOC_SESSION_STATUS_FAILED, 2414 }; 2415 2416 /** 2417 * enum qca_wlan_vendor_attr_ftm_meas: Single measurement data 2418 * 2419 * @QCA_WLAN_VENDOR_ATTR_FTM_MEAS_T1: Time of departure (TOD) of FTM packet as 2420 * recorded by responder, in picoseconds. 2421 * See IEEE P802.11-REVmc/D7.0, 11.24.6.4 for more information. 2422 * @QCA_WLAN_VENDOR_ATTR_FTM_MEAS_T2: Time of arrival (TOA) of FTM packet at 2423 * initiator, in picoseconds. 2424 * See IEEE P802.11-REVmc/D7.0, 11.24.6.4 for more information. 2425 * @QCA_WLAN_VENDOR_ATTR_FTM_MEAS_T3: TOD of ACK packet as recorded by 2426 * initiator, in picoseconds. 2427 * See IEEE P802.11-REVmc/D7.0, 11.24.6.4 for more information. 2428 * @QCA_WLAN_VENDOR_ATTR_FTM_MEAS_T4: TOA of ACK packet at 2429 * responder, in picoseconds. 2430 * See IEEE P802.11-REVmc/D7.0, 11.24.6.4 for more information. 2431 * @QCA_WLAN_VENDOR_ATTR_FTM_MEAS_RSSI: RSSI (signal level) as recorded 2432 * during this measurement exchange. Optional and will be provided if 2433 * the hardware can measure it. 2434 * @QCA_WLAN_VENDOR_ATTR_FTM_MEAS_TOD_ERR: TOD error reported by 2435 * responder. Not always provided. 2436 * See IEEE P802.11-REVmc/D7.0, 9.6.8.33 for more information. 2437 * @QCA_WLAN_VENDOR_ATTR_FTM_MEAS_TOA_ERR: TOA error reported by 2438 * responder. Not always provided. 2439 * See IEEE P802.11-REVmc/D7.0, 9.6.8.33 for more information. 2440 * @QCA_WLAN_VENDOR_ATTR_FTM_MEAS_INITIATOR_TOD_ERR: TOD error measured by 2441 * initiator. Not always provided. 2442 * See IEEE P802.11-REVmc/D7.0, 9.6.8.33 for more information. 2443 * @QCA_WLAN_VENDOR_ATTR_FTM_MEAS_INITIATOR_TOA_ERR: TOA error measured by 2444 * initiator. Not always provided. 2445 * See IEEE P802.11-REVmc/D7.0, 9.6.8.33 for more information. 2446 * @QCA_WLAN_VENDOR_ATTR_FTM_MEAS_PAD: Dummy attribute for padding. 2447 */ 2448 enum qca_wlan_vendor_attr_ftm_meas { 2449 QCA_WLAN_VENDOR_ATTR_FTM_MEAS_INVALID, 2450 QCA_WLAN_VENDOR_ATTR_FTM_MEAS_T1, 2451 QCA_WLAN_VENDOR_ATTR_FTM_MEAS_T2, 2452 QCA_WLAN_VENDOR_ATTR_FTM_MEAS_T3, 2453 QCA_WLAN_VENDOR_ATTR_FTM_MEAS_T4, 2454 QCA_WLAN_VENDOR_ATTR_FTM_MEAS_RSSI, 2455 QCA_WLAN_VENDOR_ATTR_FTM_MEAS_TOD_ERR, 2456 QCA_WLAN_VENDOR_ATTR_FTM_MEAS_TOA_ERR, 2457 QCA_WLAN_VENDOR_ATTR_FTM_MEAS_INITIATOR_TOD_ERR, 2458 QCA_WLAN_VENDOR_ATTR_FTM_MEAS_INITIATOR_TOA_ERR, 2459 QCA_WLAN_VENDOR_ATTR_FTM_MEAS_PAD, 2460 /* keep last */ 2461 QCA_WLAN_VENDOR_ATTR_FTM_MEAS_AFTER_LAST, 2462 QCA_WLAN_VENDOR_ATTR_FTM_MEAS_MAX = 2463 QCA_WLAN_VENDOR_ATTR_FTM_MEAS_AFTER_LAST - 1, 2464 }; 2465 2466 /** 2467 * enum qca_wlan_vendor_attr_aoa_type - AOA measurement type 2468 * 2469 * @QCA_WLAN_VENDOR_ATTR_AOA_TYPE_TOP_CIR_PHASE: Phase of the strongest 2470 * CIR (channel impulse response) path for each antenna. 2471 * @QCA_WLAN_VENDOR_ATTR_AOA_TYPE_TOP_CIR_PHASE_AMP: Phase and amplitude 2472 * of the strongest CIR path for each antenna. 2473 */ 2474 enum qca_wlan_vendor_attr_aoa_type { 2475 QCA_WLAN_VENDOR_ATTR_AOA_TYPE_TOP_CIR_PHASE, 2476 QCA_WLAN_VENDOR_ATTR_AOA_TYPE_TOP_CIR_PHASE_AMP, 2477 QCA_WLAN_VENDOR_ATTR_AOA_TYPE_MAX 2478 }; 2479 2480 /** 2481 * enum qca_wlan_vendor_attr_encryption_test - Attributes to 2482 * validate encryption engine 2483 * 2484 * @QCA_WLAN_VENDOR_ATTR_ENCRYPTION_TEST_NEEDS_DECRYPTION: Flag attribute. 2485 * This will be included if the request is for decryption; if not included, 2486 * the request is treated as a request for encryption by default. 2487 * @QCA_WLAN_VENDOR_ATTR_ENCRYPTION_TEST_CIPHER: Unsigned 32-bit value 2488 * indicating the key cipher suite. Takes same values as 2489 * NL80211_ATTR_KEY_CIPHER. 2490 * @QCA_WLAN_VENDOR_ATTR_ENCRYPTION_TEST_KEYID: Unsigned 8-bit value 2491 * Key Id to be used for encryption 2492 * @QCA_WLAN_VENDOR_ATTR_ENCRYPTION_TEST_TK: Array of 8-bit values. 2493 * Key (TK) to be used for encryption/decryption 2494 * @QCA_WLAN_VENDOR_ATTR_ENCRYPTION_TEST_PN: Array of 8-bit values. 2495 * Packet number to be specified for encryption/decryption 2496 * 6 bytes for TKIP/CCMP/GCMP. 2497 * @QCA_WLAN_VENDOR_ATTR_ENCRYPTION_TEST_DATA: Array of 8-bit values 2498 * representing the 802.11 packet (header + payload + FCS) that 2499 * needs to be encrypted/decrypted. 2500 * Encrypted/decrypted response from the driver will also be sent 2501 * to userspace with the same attribute. 2502 */ 2503 enum qca_wlan_vendor_attr_encryption_test { 2504 QCA_WLAN_VENDOR_ATTR_ENCRYPTION_TEST_INVALID = 0, 2505 QCA_WLAN_VENDOR_ATTR_ENCRYPTION_TEST_NEEDS_DECRYPTION, 2506 QCA_WLAN_VENDOR_ATTR_ENCRYPTION_TEST_CIPHER, 2507 QCA_WLAN_VENDOR_ATTR_ENCRYPTION_TEST_KEYID, 2508 QCA_WLAN_VENDOR_ATTR_ENCRYPTION_TEST_TK, 2509 QCA_WLAN_VENDOR_ATTR_ENCRYPTION_TEST_PN, 2510 QCA_WLAN_VENDOR_ATTR_ENCRYPTION_TEST_DATA, 2511 2512 /* keep last */ 2513 QCA_WLAN_VENDOR_ATTR_ENCRYPTION_TEST_AFTER_LAST, 2514 QCA_WLAN_VENDOR_ATTR_ENCRYPTION_TEST_MAX = 2515 QCA_WLAN_VENDOR_ATTR_ENCRYPTION_TEST_AFTER_LAST - 1 2516 }; 2517 2518 /** 2519 * enum qca_wlan_vendor_attr_dmg_rf_sector_type - Type of 2520 * sector for DMG RF sector operations. 2521 * 2522 * @QCA_WLAN_VENDOR_ATTR_DMG_RF_SECTOR_TYPE_RX: RX sector 2523 * @QCA_WLAN_VENDOR_ATTR_DMG_RF_SECTOR_TYPE_TX: TX sector 2524 */ 2525 enum qca_wlan_vendor_attr_dmg_rf_sector_type { 2526 QCA_WLAN_VENDOR_ATTR_DMG_RF_SECTOR_TYPE_RX, 2527 QCA_WLAN_VENDOR_ATTR_DMG_RF_SECTOR_TYPE_TX, 2528 QCA_WLAN_VENDOR_ATTR_DMG_RF_SECTOR_TYPE_MAX 2529 }; 2530 2531 /** 2532 * enum qca_wlan_vendor_attr_fw_state - State of firmware 2533 * 2534 * @QCA_WLAN_VENDOR_ATTR_FW_STATE_ERROR: FW is in bad state 2535 * @QCA_WLAN_VENDOR_ATTR_FW_STATE_ACTIVE: FW is active 2536 */ 2537 enum qca_wlan_vendor_attr_fw_state { 2538 QCA_WLAN_VENDOR_ATTR_FW_STATE_ERROR, 2539 QCA_WLAN_VENDOR_ATTR_FW_STATE_ACTIVE, 2540 QCA_WLAN_VENDOR_ATTR_FW_STATE_MAX 2541 }; 2542 2543 /** 2544 * BRP antenna limit mode 2545 * 2546 * @QCA_WLAN_VENDOR_ATTR_BRP_ANT_LIMIT_MODE_DISABLE: Disable BRP force 2547 * antenna limit, BRP will be performed as usual. 2548 * @QCA_WLAN_VENDOR_ATTR_BRP_ANT_LIMIT_MODE_EFFECTIVE: Define maximal 2549 * antennas limit. the hardware may use less antennas than the 2550 * maximum limit. 2551 * @QCA_WLAN_VENDOR_ATTR_BRP_ANT_LIMIT_MODE_FORCE: The hardware will 2552 * use exactly the specified number of antennas for BRP. 2553 */ 2554 enum qca_wlan_vendor_attr_brp_ant_limit_mode { 2555 QCA_WLAN_VENDOR_ATTR_BRP_ANT_LIMIT_MODE_DISABLE, 2556 QCA_WLAN_VENDOR_ATTR_BRP_ANT_LIMIT_MODE_EFFECTIVE, 2557 QCA_WLAN_VENDOR_ATTR_BRP_ANT_LIMIT_MODE_FORCE, 2558 QCA_WLAN_VENDOR_ATTR_BRP_ANT_LIMIT_MODE_MAX 2559 }; 2560 2561 /** 2562 * enum qca_wlan_vendor_attr_dmg_rf_sector_cfg - Attributes for 2563 * DMG RF sector configuration for a single RF module. 2564 * The values are defined in a compact way which closely matches 2565 * the way it is stored in HW registers. 2566 * The configuration provides values for 32 antennas and 8 distribution 2567 * amplifiers, and together describes the characteristics of the RF 2568 * sector - such as a beam in some direction with some gain. 2569 * 2570 * @QCA_WLAN_VENDOR_ATTR_DMG_RF_SECTOR_CFG_MODULE_INDEX: Index 2571 * of RF module for this configuration. 2572 * @QCA_WLAN_VENDOR_ATTR_DMG_RF_SECTOR_CFG_ETYPE0: Bit 0 of edge 2573 * amplifier gain index. Unsigned 32 bit number containing 2574 * bits for all 32 antennas. 2575 * @QCA_WLAN_VENDOR_ATTR_DMG_RF_SECTOR_CFG_ETYPE1: Bit 1 of edge 2576 * amplifier gain index. Unsigned 32 bit number containing 2577 * bits for all 32 antennas. 2578 * @QCA_WLAN_VENDOR_ATTR_DMG_RF_SECTOR_CFG_ETYPE2: Bit 2 of edge 2579 * amplifier gain index. Unsigned 32 bit number containing 2580 * bits for all 32 antennas. 2581 * @QCA_WLAN_VENDOR_ATTR_DMG_RF_SECTOR_CFG_PSH_HI: Phase values 2582 * for first 16 antennas, 2 bits per antenna. 2583 * @QCA_WLAN_VENDOR_ATTR_DMG_RF_SECTOR_CFG_PSH_LO: Phase values 2584 * for last 16 antennas, 2 bits per antenna. 2585 * @QCA_WLAN_VENDOR_ATTR_DMG_RF_SECTOR_CFG_DTYPE_X16: Contains 2586 * DTYPE values (3 bits) for each distribution amplifier, followed 2587 * by X16 switch bits for each distribution amplifier. There are 2588 * total of 8 distribution amplifiers. 2589 */ 2590 enum qca_wlan_vendor_attr_dmg_rf_sector_cfg { 2591 QCA_WLAN_VENDOR_ATTR_DMG_RF_SECTOR_CFG_INVALID = 0, 2592 QCA_WLAN_VENDOR_ATTR_DMG_RF_SECTOR_CFG_MODULE_INDEX = 1, 2593 QCA_WLAN_VENDOR_ATTR_DMG_RF_SECTOR_CFG_ETYPE0 = 2, 2594 QCA_WLAN_VENDOR_ATTR_DMG_RF_SECTOR_CFG_ETYPE1 = 3, 2595 QCA_WLAN_VENDOR_ATTR_DMG_RF_SECTOR_CFG_ETYPE2 = 4, 2596 QCA_WLAN_VENDOR_ATTR_DMG_RF_SECTOR_CFG_PSH_HI = 5, 2597 QCA_WLAN_VENDOR_ATTR_DMG_RF_SECTOR_CFG_PSH_LO = 6, 2598 QCA_WLAN_VENDOR_ATTR_DMG_RF_SECTOR_CFG_DTYPE_X16 = 7, 2599 2600 /* keep last */ 2601 QCA_WLAN_VENDOR_ATTR_DMG_RF_SECTOR_CFG_AFTER_LAST, 2602 QCA_WLAN_VENDOR_ATTR_DMG_RF_SECTOR_CFG_MAX = 2603 QCA_WLAN_VENDOR_ATTR_DMG_RF_SECTOR_CFG_AFTER_LAST - 1 2604 }; 2605 2606 enum qca_wlan_vendor_attr_ll_stats_set { 2607 QCA_WLAN_VENDOR_ATTR_LL_STATS_SET_INVALID = 0, 2608 /* Unsigned 32-bit value */ 2609 QCA_WLAN_VENDOR_ATTR_LL_STATS_SET_CONFIG_MPDU_SIZE_THRESHOLD = 1, 2610 QCA_WLAN_VENDOR_ATTR_LL_STATS_SET_CONFIG_AGGRESSIVE_STATS_GATHERING = 2, 2611 /* keep last */ 2612 QCA_WLAN_VENDOR_ATTR_LL_STATS_SET_AFTER_LAST, 2613 QCA_WLAN_VENDOR_ATTR_LL_STATS_SET_MAX = 2614 QCA_WLAN_VENDOR_ATTR_LL_STATS_SET_AFTER_LAST - 1, 2615 }; 2616 2617 enum qca_wlan_vendor_attr_ll_stats_clr { 2618 QCA_WLAN_VENDOR_ATTR_LL_STATS_CLR_INVALID = 0, 2619 /* Unsigned 32bit bitmap for clearing statistics 2620 * All radio statistics 0x00000001 2621 * cca_busy_time (within radio statistics) 0x00000002 2622 * All channel stats (within radio statistics) 0x00000004 2623 * All scan statistics (within radio statistics) 0x00000008 2624 * All interface statistics 0x00000010 2625 * All tx rate statistics (within interface statistics) 0x00000020 2626 * All ac statistics (with in interface statistics) 0x00000040 2627 * All contention (min, max, avg) statistics (within ac statisctics) 2628 * 0x00000080. 2629 */ 2630 QCA_WLAN_VENDOR_ATTR_LL_STATS_CLR_CONFIG_REQ_MASK = 1, 2631 /* Unsigned 8 bit value: Request to stop statistics collection */ 2632 QCA_WLAN_VENDOR_ATTR_LL_STATS_CLR_CONFIG_STOP_REQ = 2, 2633 2634 /* Unsigned 32 bit bitmap: Response from the driver 2635 * for the cleared statistics 2636 */ 2637 QCA_WLAN_VENDOR_ATTR_LL_STATS_CLR_CONFIG_RSP_MASK = 3, 2638 /* Unsigned 8 bit value: Response from driver/firmware 2639 * for the stop request 2640 */ 2641 QCA_WLAN_VENDOR_ATTR_LL_STATS_CLR_CONFIG_STOP_RSP = 4, 2642 /* keep last */ 2643 QCA_WLAN_VENDOR_ATTR_LL_STATS_CLR_AFTER_LAST, 2644 QCA_WLAN_VENDOR_ATTR_LL_STATS_CLR_MAX = 2645 QCA_WLAN_VENDOR_ATTR_LL_STATS_CLR_AFTER_LAST - 1, 2646 }; 2647 2648 enum qca_wlan_vendor_attr_ll_stats_get { 2649 QCA_WLAN_VENDOR_ATTR_LL_STATS_GET_INVALID = 0, 2650 /* Unsigned 32 bit value provided by the caller issuing the GET stats 2651 * command. When reporting the stats results, the driver uses the same 2652 * value to indicate which GET request the results correspond to. 2653 */ 2654 QCA_WLAN_VENDOR_ATTR_LL_STATS_GET_CONFIG_REQ_ID = 1, 2655 /* Unsigned 32 bit value - bit mask to identify what statistics are 2656 * requested for retrieval. 2657 * Radio Statistics 0x00000001 2658 * Interface Statistics 0x00000020 2659 * All Peer Statistics 0x00000040 2660 * Peer Statistics 0x00000080 2661 */ 2662 QCA_WLAN_VENDOR_ATTR_LL_STATS_GET_CONFIG_REQ_MASK = 2, 2663 /* keep last */ 2664 QCA_WLAN_VENDOR_ATTR_LL_STATS_GET_AFTER_LAST, 2665 QCA_WLAN_VENDOR_ATTR_LL_STATS_GET_MAX = 2666 QCA_WLAN_VENDOR_ATTR_LL_STATS_GET_AFTER_LAST - 1, 2667 }; 2668 2669 enum qca_wlan_vendor_attr_ll_stats_results { 2670 QCA_WLAN_VENDOR_ATTR_LL_STATS_INVALID = 0, 2671 /* Unsigned 32bit value. Used by the driver; must match the request id 2672 * provided with the QCA_NL80211_VENDOR_SUBCMD_LL_STATS_GET command. 2673 */ 2674 QCA_WLAN_VENDOR_ATTR_LL_STATS_RESULTS_REQ_ID = 1, 2675 2676 /* Unsigned 32 bit value */ 2677 QCA_WLAN_VENDOR_ATTR_LL_STATS_IFACE_BEACON_RX = 2, 2678 /* Unsigned 32 bit value */ 2679 QCA_WLAN_VENDOR_ATTR_LL_STATS_IFACE_MGMT_RX = 3, 2680 /* Unsigned 32 bit value */ 2681 QCA_WLAN_VENDOR_ATTR_LL_STATS_IFACE_MGMT_ACTION_RX = 4, 2682 /* Unsigned 32 bit value */ 2683 QCA_WLAN_VENDOR_ATTR_LL_STATS_IFACE_MGMT_ACTION_TX = 5, 2684 /* Signed 32 bit value */ 2685 QCA_WLAN_VENDOR_ATTR_LL_STATS_IFACE_RSSI_MGMT = 6, 2686 /* Signed 32 bit value */ 2687 QCA_WLAN_VENDOR_ATTR_LL_STATS_IFACE_RSSI_DATA = 7, 2688 /* Signed 32 bit value */ 2689 QCA_WLAN_VENDOR_ATTR_LL_STATS_IFACE_RSSI_ACK = 8, 2690 2691 /* Attributes of type QCA_WLAN_VENDOR_ATTR_LL_STATS_IFACE_INFO_* are 2692 * nested within the interface stats. 2693 */ 2694 2695 /* Interface mode, e.g., STA, SOFTAP, IBSS, etc. 2696 * Type = enum wifi_interface_mode. 2697 */ 2698 QCA_WLAN_VENDOR_ATTR_LL_STATS_IFACE_INFO_MODE = 9, 2699 /* Interface MAC address. An array of 6 Unsigned int8 */ 2700 QCA_WLAN_VENDOR_ATTR_LL_STATS_IFACE_INFO_MAC_ADDR = 10, 2701 /* Type = enum wifi_connection_state, e.g., DISCONNECTED, 2702 * AUTHENTICATING, etc. valid for STA, CLI only. 2703 */ 2704 QCA_WLAN_VENDOR_ATTR_LL_STATS_IFACE_INFO_STATE = 11, 2705 /* Type = enum wifi_roam_state. Roaming state, e.g., IDLE or ACTIVE 2706 */ 2707 QCA_WLAN_VENDOR_ATTR_LL_STATS_IFACE_INFO_ROAMING = 12, 2708 /* Unsigned 32 bit value. WIFI_CAPABILITY_XXX */ 2709 QCA_WLAN_VENDOR_ATTR_LL_STATS_IFACE_INFO_CAPABILITIES = 13, 2710 /* NULL terminated SSID. An array of 33 Unsigned 8bit values */ 2711 QCA_WLAN_VENDOR_ATTR_LL_STATS_IFACE_INFO_SSID = 14, 2712 /* BSSID. An array of 6 unsigned 8 bit values */ 2713 QCA_WLAN_VENDOR_ATTR_LL_STATS_IFACE_INFO_BSSID = 15, 2714 /* Country string advertised by AP. An array of 3 unsigned 8 bit 2715 * values. 2716 */ 2717 QCA_WLAN_VENDOR_ATTR_LL_STATS_IFACE_INFO_AP_COUNTRY_STR = 16, 2718 /* Country string for this association. An array of 3 unsigned 8 bit 2719 * values. 2720 */ 2721 QCA_WLAN_VENDOR_ATTR_LL_STATS_IFACE_INFO_COUNTRY_STR = 17, 2722 2723 /* Attributes of type QCA_WLAN_VENDOR_ATTR_LL_STATS_WMM_AC_* could 2724 * be nested within the interface stats. 2725 */ 2726 2727 /* Type = enum wifi_traffic_ac, e.g., V0, VI, BE and BK */ 2728 QCA_WLAN_VENDOR_ATTR_LL_STATS_WMM_AC_AC = 18, 2729 /* Unsigned int 32 value corresponding to respective AC */ 2730 QCA_WLAN_VENDOR_ATTR_LL_STATS_WMM_AC_TX_MPDU = 19, 2731 /* Unsigned int 32 value corresponding to respective AC */ 2732 QCA_WLAN_VENDOR_ATTR_LL_STATS_WMM_AC_RX_MPDU = 20, 2733 /* Unsigned int 32 value corresponding to respective AC */ 2734 QCA_WLAN_VENDOR_ATTR_LL_STATS_WMM_AC_TX_MCAST = 21, 2735 /* Unsigned int 32 value corresponding to respective AC */ 2736 QCA_WLAN_VENDOR_ATTR_LL_STATS_WMM_AC_RX_MCAST = 22, 2737 /* Unsigned int 32 value corresponding to respective AC */ 2738 QCA_WLAN_VENDOR_ATTR_LL_STATS_WMM_AC_RX_AMPDU = 23, 2739 /* Unsigned int 32 value corresponding to respective AC */ 2740 QCA_WLAN_VENDOR_ATTR_LL_STATS_WMM_AC_TX_AMPDU = 24, 2741 /* Unsigned int 32 value corresponding to respective AC */ 2742 QCA_WLAN_VENDOR_ATTR_LL_STATS_WMM_AC_MPDU_LOST = 25, 2743 /* Unsigned int 32 value corresponding to respective AC */ 2744 QCA_WLAN_VENDOR_ATTR_LL_STATS_WMM_AC_RETRIES = 26, 2745 /* Unsigned int 32 value corresponding to respective AC */ 2746 QCA_WLAN_VENDOR_ATTR_LL_STATS_WMM_AC_RETRIES_SHORT = 27, 2747 /* Unsigned int 32 values corresponding to respective AC */ 2748 QCA_WLAN_VENDOR_ATTR_LL_STATS_WMM_AC_RETRIES_LONG = 28, 2749 /* Unsigned int 32 values corresponding to respective AC */ 2750 QCA_WLAN_VENDOR_ATTR_LL_STATS_WMM_AC_CONTENTION_TIME_MIN = 29, 2751 /* Unsigned int 32 values corresponding to respective AC */ 2752 QCA_WLAN_VENDOR_ATTR_LL_STATS_WMM_AC_CONTENTION_TIME_MAX = 30, 2753 /* Unsigned int 32 values corresponding to respective AC */ 2754 QCA_WLAN_VENDOR_ATTR_LL_STATS_WMM_AC_CONTENTION_TIME_AVG = 31, 2755 /* Unsigned int 32 values corresponding to respective AC */ 2756 QCA_WLAN_VENDOR_ATTR_LL_STATS_WMM_AC_CONTENTION_NUM_SAMPLES = 32, 2757 /* Unsigned 32 bit value. Number of peers */ 2758 QCA_WLAN_VENDOR_ATTR_LL_STATS_IFACE_NUM_PEERS = 33, 2759 2760 /* Attributes of type QCA_WLAN_VENDOR_ATTR_LL_STATS_PEER_INFO_* are 2761 * nested within the interface stats. 2762 */ 2763 2764 /* Type = enum wifi_peer_type. Peer type, e.g., STA, AP, P2P GO etc. */ 2765 QCA_WLAN_VENDOR_ATTR_LL_STATS_PEER_INFO_TYPE = 34, 2766 /* MAC addr corresponding to respective peer. An array of 6 unsigned 2767 * 8 bit values. 2768 */ 2769 QCA_WLAN_VENDOR_ATTR_LL_STATS_PEER_INFO_MAC_ADDRESS = 35, 2770 /* Unsigned int 32 bit value representing capabilities corresponding 2771 * to respective peer. 2772 */ 2773 QCA_WLAN_VENDOR_ATTR_LL_STATS_PEER_INFO_CAPABILITIES = 36, 2774 /* Unsigned 32 bit value. Number of rates */ 2775 QCA_WLAN_VENDOR_ATTR_LL_STATS_PEER_INFO_NUM_RATES = 37, 2776 2777 /* Attributes of type QCA_WLAN_VENDOR_ATTR_LL_STATS_RATE_* 2778 * are nested within the rate stat. 2779 */ 2780 2781 /* Wi-Fi Rate - separate attributes defined for individual fields */ 2782 2783 /* Unsigned int 8 bit value; 0: OFDM, 1:CCK, 2:HT 3:VHT 4..7 reserved */ 2784 QCA_WLAN_VENDOR_ATTR_LL_STATS_RATE_PREAMBLE = 38, 2785 /* Unsigned int 8 bit value; 0:1x1, 1:2x2, 3:3x3, 4:4x4 */ 2786 QCA_WLAN_VENDOR_ATTR_LL_STATS_RATE_NSS = 39, 2787 /* Unsigned int 8 bit value; 0:20 MHz, 1:40 MHz, 2:80 MHz, 3:160 MHz */ 2788 QCA_WLAN_VENDOR_ATTR_LL_STATS_RATE_BW = 40, 2789 /* Unsigned int 8 bit value; OFDM/CCK rate code would be as per IEEE Std 2790 * in the units of 0.5 Mbps HT/VHT it would be MCS index 2791 */ 2792 QCA_WLAN_VENDOR_ATTR_LL_STATS_RATE_MCS_INDEX = 41, 2793 2794 /* Unsigned 32 bit value. Bit rate in units of 100 kbps */ 2795 QCA_WLAN_VENDOR_ATTR_LL_STATS_RATE_BIT_RATE = 42, 2796 2797 /* Attributes of type QCA_WLAN_VENDOR_ATTR_LL_STATS_RATE_STAT_* could be 2798 * nested within the peer info stats. 2799 */ 2800 2801 /* Unsigned int 32 bit value. Number of successfully transmitted data 2802 * packets, i.e., with ACK received corresponding to the respective 2803 * rate. 2804 */ 2805 QCA_WLAN_VENDOR_ATTR_LL_STATS_RATE_TX_MPDU = 43, 2806 /* Unsigned int 32 bit value. Number of received data packets 2807 * corresponding to the respective rate. 2808 */ 2809 QCA_WLAN_VENDOR_ATTR_LL_STATS_RATE_RX_MPDU = 44, 2810 /* Unsigned int 32 bit value. Number of data packet losses, i.e., no ACK 2811 * received corresponding to the respective rate. 2812 */ 2813 QCA_WLAN_VENDOR_ATTR_LL_STATS_RATE_MPDU_LOST = 45, 2814 /* Unsigned int 32 bit value. Total number of data packet retries for 2815 * the respective rate. 2816 */ 2817 QCA_WLAN_VENDOR_ATTR_LL_STATS_RATE_RETRIES = 46, 2818 /* Unsigned int 32 bit value. Total number of short data packet retries 2819 * for the respective rate. 2820 */ 2821 QCA_WLAN_VENDOR_ATTR_LL_STATS_RATE_RETRIES_SHORT = 47, 2822 /* Unsigned int 32 bit value. Total number of long data packet retries 2823 * for the respective rate. 2824 */ 2825 QCA_WLAN_VENDOR_ATTR_LL_STATS_RATE_RETRIES_LONG = 48, 2826 2827 QCA_WLAN_VENDOR_ATTR_LL_STATS_RADIO_ID = 49, 2828 /* Unsigned 32 bit value. Total number of msecs the radio is awake 2829 * accruing over time. 2830 */ 2831 QCA_WLAN_VENDOR_ATTR_LL_STATS_RADIO_ON_TIME = 50, 2832 /* Unsigned 32 bit value. Total number of msecs the radio is 2833 * transmitting accruing over time. 2834 */ 2835 QCA_WLAN_VENDOR_ATTR_LL_STATS_RADIO_TX_TIME = 51, 2836 /* Unsigned 32 bit value. Total number of msecs the radio is in active 2837 * receive accruing over time. 2838 */ 2839 QCA_WLAN_VENDOR_ATTR_LL_STATS_RADIO_RX_TIME = 52, 2840 /* Unsigned 32 bit value. Total number of msecs the radio is awake due 2841 * to all scan accruing over time. 2842 */ 2843 QCA_WLAN_VENDOR_ATTR_LL_STATS_RADIO_ON_TIME_SCAN = 53, 2844 /* Unsigned 32 bit value. Total number of msecs the radio is awake due 2845 * to NAN accruing over time. 2846 */ 2847 QCA_WLAN_VENDOR_ATTR_LL_STATS_RADIO_ON_TIME_NBD = 54, 2848 /* Unsigned 32 bit value. Total number of msecs the radio is awake due 2849 * to GSCAN accruing over time. 2850 */ 2851 QCA_WLAN_VENDOR_ATTR_LL_STATS_RADIO_ON_TIME_GSCAN = 55, 2852 /* Unsigned 32 bit value. Total number of msecs the radio is awake due 2853 * to roam scan accruing over time. 2854 */ 2855 QCA_WLAN_VENDOR_ATTR_LL_STATS_RADIO_ON_TIME_ROAM_SCAN = 56, 2856 /* Unsigned 32 bit value. Total number of msecs the radio is awake due 2857 * to PNO scan accruing over time. 2858 */ 2859 QCA_WLAN_VENDOR_ATTR_LL_STATS_RADIO_ON_TIME_PNO_SCAN = 57, 2860 /* Unsigned 32 bit value. Total number of msecs the radio is awake due 2861 * to Hotspot 2.0 scans and GAS exchange accruing over time. 2862 */ 2863 QCA_WLAN_VENDOR_ATTR_LL_STATS_RADIO_ON_TIME_HS20 = 58, 2864 /* Unsigned 32 bit value. Number of channels. */ 2865 QCA_WLAN_VENDOR_ATTR_LL_STATS_RADIO_NUM_CHANNELS = 59, 2866 2867 /* Attributes of type QCA_WLAN_VENDOR_ATTR_LL_STATS_CHANNEL_INFO_* could 2868 * be nested within the channel stats. 2869 */ 2870 2871 /* Type = enum wifi_channel_width. Channel width, e.g., 20, 40, 80 */ 2872 QCA_WLAN_VENDOR_ATTR_LL_STATS_CHANNEL_INFO_WIDTH = 60, 2873 /* Unsigned 32 bit value. Primary 20 MHz channel. */ 2874 QCA_WLAN_VENDOR_ATTR_LL_STATS_CHANNEL_INFO_CENTER_FREQ = 61, 2875 /* Unsigned 32 bit value. Center frequency (MHz) first segment. */ 2876 QCA_WLAN_VENDOR_ATTR_LL_STATS_CHANNEL_INFO_CENTER_FREQ0 = 62, 2877 /* Unsigned 32 bit value. Center frequency (MHz) second segment. */ 2878 QCA_WLAN_VENDOR_ATTR_LL_STATS_CHANNEL_INFO_CENTER_FREQ1 = 63, 2879 2880 /* Attributes of type QCA_WLAN_VENDOR_ATTR_LL_STATS_CHANNEL_* could be 2881 * nested within the radio stats. 2882 */ 2883 2884 /* Unsigned int 32 bit value representing total number of msecs the 2885 * radio is awake on that channel accruing over time, corresponding to 2886 * the respective channel. 2887 */ 2888 QCA_WLAN_VENDOR_ATTR_LL_STATS_CHANNEL_ON_TIME = 64, 2889 /* Unsigned int 32 bit value representing total number of msecs the CCA 2890 * register is busy accruing over time corresponding to the respective 2891 * channel. 2892 */ 2893 QCA_WLAN_VENDOR_ATTR_LL_STATS_CHANNEL_CCA_BUSY_TIME = 65, 2894 2895 QCA_WLAN_VENDOR_ATTR_LL_STATS_NUM_RADIOS = 66, 2896 2897 /* Signifies the nested list of channel attributes 2898 * QCA_WLAN_VENDOR_ATTR_LL_STATS_CHANNEL_INFO_* 2899 */ 2900 QCA_WLAN_VENDOR_ATTR_LL_STATS_CH_INFO = 67, 2901 2902 /* Signifies the nested list of peer info attributes 2903 * QCA_WLAN_VENDOR_ATTR_LL_STATS_PEER_INFO_* 2904 */ 2905 QCA_WLAN_VENDOR_ATTR_LL_STATS_PEER_INFO = 68, 2906 2907 /* Signifies the nested list of rate info attributes 2908 * QCA_WLAN_VENDOR_ATTR_LL_STATS_RATE_* 2909 */ 2910 QCA_WLAN_VENDOR_ATTR_LL_STATS_PEER_INFO_RATE_INFO = 69, 2911 2912 /* Signifies the nested list of wmm info attributes 2913 * QCA_WLAN_VENDOR_ATTR_LL_STATS_WMM_AC_* 2914 */ 2915 QCA_WLAN_VENDOR_ATTR_LL_STATS_WMM_INFO = 70, 2916 2917 /* Unsigned 8 bit value. Used by the driver; if set to 1, it indicates 2918 * that more stats, e.g., peers or radio, are to follow in the next 2919 * QCA_NL80211_VENDOR_SUBCMD_LL_STATS_*_RESULTS event. 2920 * Otherwise, it is set to 0. 2921 */ 2922 QCA_WLAN_VENDOR_ATTR_LL_STATS_RESULTS_MORE_DATA = 71, 2923 2924 /* Unsigned 64 bit value */ 2925 QCA_WLAN_VENDOR_ATTR_LL_STATS_IFACE_AVERAGE_TSF_OFFSET = 72, 2926 2927 /* Unsigned 32 bit value */ 2928 QCA_WLAN_VENDOR_ATTR_LL_STATS_IFACE_LEAKY_AP_DETECTED = 73, 2929 2930 /* Unsigned 32 bit value */ 2931 QCA_WLAN_VENDOR_ATTR_LL_STATS_IFACE_LEAKY_AP_AVG_NUM_FRAMES_LEAKED = 74, 2932 2933 /* Unsigned 32 bit value */ 2934 QCA_WLAN_VENDOR_ATTR_LL_STATS_IFACE_LEAKY_AP_GUARD_TIME = 75, 2935 2936 /* Unsigned 32 bit value */ 2937 QCA_WLAN_VENDOR_ATTR_LL_STATS_TYPE = 76, 2938 2939 /* Unsigned 32 bit value */ 2940 QCA_WLAN_VENDOR_ATTR_LL_STATS_RADIO_NUM_TX_LEVELS = 77, 2941 2942 /* Number of msecs the radio spent in transmitting for each power level 2943 */ 2944 QCA_WLAN_VENDOR_ATTR_LL_STATS_RADIO_TX_TIME_PER_LEVEL = 78, 2945 2946 /* Unsigned 32 bit value */ 2947 QCA_WLAN_VENDOR_ATTR_LL_STATS_IFACE_RTS_SUCC_CNT = 79, 2948 /* Unsigned 32 bit value */ 2949 QCA_WLAN_VENDOR_ATTR_LL_STATS_IFACE_RTS_FAIL_CNT = 80, 2950 /* Unsigned 32 bit value */ 2951 QCA_WLAN_VENDOR_ATTR_LL_STATS_IFACE_PPDU_SUCC_CNT = 81, 2952 /* Unsigned 32 bit value */ 2953 QCA_WLAN_VENDOR_ATTR_LL_STATS_IFACE_PPDU_FAIL_CNT = 82, 2954 2955 /* Unsigned int 32 value. 2956 * Pending MSDUs corresponding to respective AC. 2957 */ 2958 QCA_WLAN_VENDOR_ATTR_LL_STATS_WMM_AC_PENDING_MSDU = 83, 2959 2960 /* keep last */ 2961 QCA_WLAN_VENDOR_ATTR_LL_STATS_AFTER_LAST, 2962 QCA_WLAN_VENDOR_ATTR_LL_STATS_MAX = 2963 QCA_WLAN_VENDOR_ATTR_LL_STATS_AFTER_LAST - 1, 2964 }; 2965 2966 enum qca_wlan_vendor_attr_ll_stats_type { 2967 QCA_NL80211_VENDOR_SUBCMD_LL_STATS_TYPE_INVALID = 0, 2968 QCA_NL80211_VENDOR_SUBCMD_LL_STATS_TYPE_RADIO = 1, 2969 QCA_NL80211_VENDOR_SUBCMD_LL_STATS_TYPE_IFACE = 2, 2970 QCA_NL80211_VENDOR_SUBCMD_LL_STATS_TYPE_PEERS = 3, 2971 2972 /* keep last */ 2973 QCA_NL80211_VENDOR_SUBCMD_LL_STATS_TYPE_AFTER_LAST, 2974 QCA_NL80211_VENDOR_SUBCMD_LL_STATS_TYPE_MAX = 2975 QCA_NL80211_VENDOR_SUBCMD_LL_STATS_TYPE_AFTER_LAST - 1, 2976 }; 2977 2978 /** 2979 * enum qca_wlan_vendor_attr_tdls_configuration - Attributes for 2980 * TDLS configuration to the host driver. 2981 * 2982 * @QCA_WLAN_VENDOR_ATTR_TDLS_CONFIG_TRIGGER_MODE: Configure the TDLS trigger 2983 * mode in the host driver. enum qca_wlan_vendor_tdls_trigger_mode 2984 * represents the different TDLS trigger modes. 2985 * @QCA_WLAN_VENDOR_ATTR_TDLS_CONFIG_TX_STATS_PERIOD: Duration (u32) within 2986 * which QCA_WLAN_VENDOR_ATTR_TDLS_CONFIG_TX_THRESHOLD number 2987 * of packets shall meet the criteria for implicit TDLS setup. 2988 * @QCA_WLAN_VENDOR_ATTR_TDLS_CONFIG_TX_THRESHOLD: Number (u32) of Tx/Rx packets 2989 * within a duration QCA_WLAN_VENDOR_ATTR_TDLS_CONFIG_TX_STATS_PERIOD 2990 * to initiate a TDLS setup. 2991 * @QCA_WLAN_VENDOR_ATTR_TDLS_CONFIG_DISCOVERY_PERIOD: Time (u32) to initiate 2992 * a TDLS Discovery to the peer. 2993 * @QCA_WLAN_VENDOR_ATTR_TDLS_CONFIG_MAX_DISCOVERY_ATTEMPT: Max number (u32) of 2994 * discovery attempts to know the TDLS capability of the peer. A peer is 2995 * marked as TDLS not capable if there is no response for all the attempts. 2996 * @QCA_WLAN_VENDOR_ATTR_TDLS_CONFIG_IDLE_TIMEOUT: Represents a duration (u32) 2997 * within which QCA_WLAN_VENDOR_ATTR_TDLS_CONFIG_IDLE_PACKET_THRESHOLD 2998 * number of TX / RX frames meet the criteria for TDLS teardown. 2999 * @QCA_WLAN_VENDOR_ATTR_TDLS_CONFIG_IDLE_PACKET_THRESHOLD: Minimum number (u32) 3000 * of Tx/Rx packets within a duration 3001 * QCA_WLAN_VENDOR_ATTR_TDLS_CONFIG_IDLE_TIMEOUT to tear down a TDLS link. 3002 * @QCA_WLAN_VENDOR_ATTR_TDLS_CONFIG_SETUP_RSSI_THRESHOLD: Threshold 3003 * corresponding to the RSSI of the peer below which a TDLS setup is 3004 * triggered. 3005 * @QCA_WLAN_VENDOR_ATTR_TDLS_CONFIG_TEARDOWN_RSSI_THRESHOLD: Threshold 3006 * corresponding to the RSSI of the peer above which a TDLS teardown is 3007 * triggered. 3008 */ 3009 enum qca_wlan_vendor_attr_tdls_configuration { 3010 QCA_WLAN_VENDOR_ATTR_TDLS_CONFIG_INVALID = 0, 3011 QCA_WLAN_VENDOR_ATTR_TDLS_CONFIG_TRIGGER_MODE = 1, 3012 3013 /* Attributes configuring the TDLS Implicit Trigger */ 3014 QCA_WLAN_VENDOR_ATTR_TDLS_CONFIG_TX_STATS_PERIOD = 2, 3015 QCA_WLAN_VENDOR_ATTR_TDLS_CONFIG_TX_THRESHOLD = 3, 3016 QCA_WLAN_VENDOR_ATTR_TDLS_CONFIG_DISCOVERY_PERIOD = 4, 3017 QCA_WLAN_VENDOR_ATTR_TDLS_CONFIG_MAX_DISCOVERY_ATTEMPT = 5, 3018 QCA_WLAN_VENDOR_ATTR_TDLS_CONFIG_IDLE_TIMEOUT = 6, 3019 QCA_WLAN_VENDOR_ATTR_TDLS_CONFIG_IDLE_PACKET_THRESHOLD = 7, 3020 QCA_WLAN_VENDOR_ATTR_TDLS_CONFIG_SETUP_RSSI_THRESHOLD = 8, 3021 QCA_WLAN_VENDOR_ATTR_TDLS_CONFIG_TEARDOWN_RSSI_THRESHOLD = 9, 3022 3023 /* keep last */ 3024 QCA_WLAN_VENDOR_ATTR_TDLS_CONFIG_AFTER_LAST, 3025 QCA_WLAN_VENDOR_ATTR_TDLS_CONFIG_MAX = 3026 QCA_WLAN_VENDOR_ATTR_TDLS_CONFIG_AFTER_LAST - 1 3027 }; 3028 3029 /** 3030 * enum qca_wlan_vendor_tdls_trigger_mode: Represents the TDLS trigger mode in 3031 * the driver 3032 * 3033 * The following are the different values for 3034 * QCA_WLAN_VENDOR_ATTR_TDLS_CONFIG_TRIGGER_MODE. 3035 * 3036 * @QCA_WLAN_VENDOR_TDLS_TRIGGER_MODE_EXPLICIT: The trigger to initiate/teardown 3037 * the TDLS connection to a respective peer comes from the user space. 3038 * wpa_supplicant provides the commands TDLS_SETUP, TDLS_TEARDOWN, 3039 * TDLS_DISCOVER to do this. 3040 * @QCA_WLAN_VENDOR_TDLS_TRIGGER_MODE_IMPLICIT: Host driver triggers this TDLS 3041 * setup/teardown to the eligible peer once the configured criteria 3042 * (such as TX/RX threshold, RSSI) is met. The attributes 3043 * in QCA_WLAN_VENDOR_ATTR_TDLS_CONFIG_IMPLICIT_PARAMS correspond to 3044 * the different configuration criteria for the TDLS trigger from the 3045 * host driver. 3046 * @QCA_WLAN_VENDOR_TDLS_TRIGGER_MODE_EXTERNAL: Enables the driver to trigger 3047 * the TDLS setup / teardown through the implicit mode only to the 3048 * configured MAC addresses (wpa_supplicant, with tdls_external_control=1, 3049 * configures the MAC address through TDLS_SETUP / TDLS_TEARDOWN commands). 3050 * External mode works on top of the implicit mode. Thus the host driver 3051 * is expected to configure in TDLS Implicit mode too to operate in 3052 * External mode. 3053 * Configuring External mode alone without Implicit mode is invalid. 3054 * 3055 * All the above implementations work as expected only when the host driver 3056 * advertises the capability WPA_DRIVER_FLAGS_TDLS_EXTERNAL_SETUP - representing 3057 * that the TDLS message exchange is not internal to the host driver, but 3058 * depends on wpa_supplicant to do the message exchange. 3059 */ 3060 enum qca_wlan_vendor_tdls_trigger_mode { 3061 QCA_WLAN_VENDOR_TDLS_TRIGGER_MODE_EXPLICIT = 1 << 0, 3062 QCA_WLAN_VENDOR_TDLS_TRIGGER_MODE_IMPLICIT = 1 << 1, 3063 QCA_WLAN_VENDOR_TDLS_TRIGGER_MODE_EXTERNAL = 1 << 2, 3064 }; 3065 3066 /** 3067 * enum qca_vendor_attr_sar_limits_selections - Source of SAR power limits 3068 * @QCA_WLAN_VENDOR_ATTR_SAR_LIMITS_SELECT_BDF0: Select SAR profile #0 3069 * that is hard-coded in the Board Data File (BDF). 3070 * @QCA_WLAN_VENDOR_ATTR_SAR_LIMITS_SELECT_BDF1: Select SAR profile #1 3071 * that is hard-coded in the Board Data File (BDF). 3072 * @QCA_WLAN_VENDOR_ATTR_SAR_LIMITS_SELECT_BDF2: Select SAR profile #2 3073 * that is hard-coded in the Board Data File (BDF). 3074 * @QCA_WLAN_VENDOR_ATTR_SAR_LIMITS_SELECT_BDF3: Select SAR profile #3 3075 * that is hard-coded in the Board Data File (BDF). 3076 * @QCA_WLAN_VENDOR_ATTR_SAR_LIMITS_SELECT_BDF4: Select SAR profile #4 3077 * that is hard-coded in the Board Data File (BDF). 3078 * @QCA_WLAN_VENDOR_ATTR_SAR_LIMITS_SELECT_NONE: Do not select any 3079 * source of SAR power limits, thereby disabling the SAR power 3080 * limit feature. 3081 * @QCA_WLAN_VENDOR_ATTR_SAR_LIMITS_SELECT_USER: Select the SAR power 3082 * limits configured by %QCA_NL80211_VENDOR_SUBCMD_SET_SAR. 3083 * @QCA_WLAN_VENDOR_ATTR_SAR_LIMITS_SELECT_V2_0: Select the SAR power 3084 * limits version 2.0 configured by %QCA_NL80211_VENDOR_SUBCMD_SET_SAR. 3085 * 3086 * This enumerates the valid set of values that may be supplied for 3087 * attribute %QCA_WLAN_VENDOR_ATTR_SAR_LIMITS_SELECT in an instance of 3088 * the %QCA_NL80211_VENDOR_SUBCMD_SET_SAR_LIMITS vendor command or in 3089 * the response to an instance of the 3090 * %QCA_NL80211_VENDOR_SUBCMD_GET_SAR_LIMITS vendor command. 3091 */ 3092 enum qca_vendor_attr_sar_limits_selections { 3093 QCA_WLAN_VENDOR_ATTR_SAR_LIMITS_SELECT_BDF0 = 0, 3094 QCA_WLAN_VENDOR_ATTR_SAR_LIMITS_SELECT_BDF1 = 1, 3095 QCA_WLAN_VENDOR_ATTR_SAR_LIMITS_SELECT_BDF2 = 2, 3096 QCA_WLAN_VENDOR_ATTR_SAR_LIMITS_SELECT_BDF3 = 3, 3097 QCA_WLAN_VENDOR_ATTR_SAR_LIMITS_SELECT_BDF4 = 4, 3098 QCA_WLAN_VENDOR_ATTR_SAR_LIMITS_SELECT_NONE = 5, 3099 QCA_WLAN_VENDOR_ATTR_SAR_LIMITS_SELECT_USER = 6, 3100 QCA_WLAN_VENDOR_ATTR_SAR_LIMITS_SELECT_V2_0 = 7, 3101 }; 3102 3103 /** 3104 * enum qca_vendor_attr_sar_limits_spec_modulations - 3105 * SAR limits specification modulation 3106 * @QCA_WLAN_VENDOR_ATTR_SAR_LIMITS_SPEC_MODULATION_CCK - 3107 * CCK modulation 3108 * @QCA_WLAN_VENDOR_ATTR_SAR_LIMITS_SPEC_MODULATION_OFDM - 3109 * OFDM modulation 3110 * 3111 * This enumerates the valid set of values that may be supplied for 3112 * attribute %QCA_WLAN_VENDOR_ATTR_SAR_LIMITS_SPEC_MODULATION in an 3113 * instance of attribute %QCA_WLAN_VENDOR_ATTR_SAR_LIMITS_SPEC in an 3114 * instance of the %QCA_NL80211_VENDOR_SUBCMD_SET_SAR_LIMITS vendor 3115 * command or in the response to an instance of the 3116 * %QCA_NL80211_VENDOR_SUBCMD_GET_SAR_LIMITS vendor command. 3117 */ 3118 enum qca_vendor_attr_sar_limits_spec_modulations { 3119 QCA_WLAN_VENDOR_ATTR_SAR_LIMITS_SPEC_MODULATION_CCK = 0, 3120 QCA_WLAN_VENDOR_ATTR_SAR_LIMITS_SPEC_MODULATION_OFDM = 1, 3121 }; 3122 3123 /** 3124 * enum qca_vendor_attr_sar_limits - Attributes for SAR power limits 3125 * 3126 * @QCA_WLAN_VENDOR_ATTR_SAR_LIMITS_SAR_ENABLE: Optional (u32) value to 3127 * select which SAR power limit table should be used. Valid 3128 * values are enumerated in enum 3129 * %qca_vendor_attr_sar_limits_selections. The existing SAR 3130 * power limit selection is unchanged if this attribute is not 3131 * present. 3132 * 3133 * @QCA_WLAN_VENDOR_ATTR_SAR_LIMITS_NUM_SPECS: Optional (u32) value 3134 * which specifies the number of SAR power limit specifications 3135 * which will follow. 3136 * 3137 * @QCA_WLAN_VENDOR_ATTR_SAR_LIMITS_SPEC: Nested array of SAR power 3138 * limit specifications. The number of specifications is 3139 * specified by @QCA_WLAN_VENDOR_ATTR_SAR_LIMITS_NUM_SPECS. Each 3140 * specification contains a set of 3141 * QCA_WLAN_VENDOR_ATTR_SAR_LIMITS_SPEC_* attributes. A 3142 * specification is uniquely identified by the attributes 3143 * %QCA_WLAN_VENDOR_ATTR_SAR_LIMITS_SPEC_BAND, 3144 * %QCA_WLAN_VENDOR_ATTR_SAR_LIMITS_SPEC_CHAIN, and 3145 * %QCA_WLAN_VENDOR_ATTR_SAR_LIMITS_SPEC_MODULATION and always 3146 * contains as a payload the attribute 3147 * %QCA_WLAN_VENDOR_ATTR_SAR_LIMITS_SPEC_POWER_LIMIT, 3148 * %QCA_WLAN_VENDOR_ATTR_SAR_LIMITS_SPEC_POWER_LIMIT_INDEX. 3149 * Either %QCA_WLAN_VENDOR_ATTR_SAR_LIMITS_SPEC_POWER_LIMIT or 3150 * %QCA_WLAN_VENDOR_ATTR_SAR_LIMITS_SPEC_POWER_LIMIT_INDEX is 3151 * needed based upon the value of 3152 * %QCA_WLAN_VENDOR_ATTR_SAR_LIMITS_SAR_ENABLE. 3153 * 3154 * @QCA_WLAN_VENDOR_ATTR_SAR_LIMITS_SPEC_BAND: Optional (u32) value to 3155 * indicate for which band this specification applies. Valid 3156 * values are enumerated in enum %nl80211_band (although not all 3157 * bands may be supported by a given device). If the attribute is 3158 * not supplied then the specification will be applied to all 3159 * supported bands. 3160 * 3161 * @QCA_WLAN_VENDOR_ATTR_SAR_LIMITS_SPEC_CHAIN: Optional (u32) value 3162 * to indicate for which antenna chain this specification 3163 * applies, i.e. 1 for chain 1, 2 for chain 2, etc. If the 3164 * attribute is not supplied then the specification will be 3165 * applied to all chains. 3166 * 3167 * @QCA_WLAN_VENDOR_ATTR_SAR_LIMITS_SPEC_MODULATION: Optional (u32) 3168 * value to indicate for which modulation scheme this 3169 * specification applies. Valid values are enumerated in enum 3170 * %qca_vendor_attr_sar_limits_spec_modulations. If the attribute 3171 * is not supplied then the specification will be applied to all 3172 * modulation schemes. 3173 * 3174 * @QCA_WLAN_VENDOR_ATTR_SAR_LIMITS_SPEC_POWER_LIMIT: Required (u32) 3175 * value to specify the actual power limit value in units of 0.5 3176 * dBm (i.e., a value of 11 represents 5.5 dBm). 3177 * This is required, when %QCA_WLAN_VENDOR_ATTR_SAR_LIMITS_SELECT is 3178 * %QCA_WLAN_VENDOR_ATTR_SAR_LIMITS_SELECT_USER. 3179 * 3180 * @QCA_WLAN_VENDOR_ATTR_SAR_LIMITS_SPEC_POWER_LIMIT_INDEX: Required (u32) 3181 * value to indicate SAR V2 indices (0 - 11) to select SAR V2 profiles. 3182 * This is required, when %QCA_WLAN_VENDOR_ATTR_SAR_LIMITS_SELECT is 3183 * %QCA_WLAN_VENDOR_ATTR_SAR_LIMITS_SELECT_V2_0. 3184 * 3185 * These attributes are used with %QCA_NL80211_VENDOR_SUBCMD_SET_SAR_LIMITS 3186 * and %QCA_NL80211_VENDOR_SUBCMD_GET_SAR_LIMITS. 3187 */ 3188 enum qca_vendor_attr_sar_limits { 3189 QCA_WLAN_VENDOR_ATTR_SAR_LIMITS_INVALID = 0, 3190 QCA_WLAN_VENDOR_ATTR_SAR_LIMITS_SAR_ENABLE = 1, 3191 QCA_WLAN_VENDOR_ATTR_SAR_LIMITS_NUM_SPECS = 2, 3192 QCA_WLAN_VENDOR_ATTR_SAR_LIMITS_SPEC = 3, 3193 QCA_WLAN_VENDOR_ATTR_SAR_LIMITS_SPEC_BAND = 4, 3194 QCA_WLAN_VENDOR_ATTR_SAR_LIMITS_SPEC_CHAIN = 5, 3195 QCA_WLAN_VENDOR_ATTR_SAR_LIMITS_SPEC_MODULATION = 6, 3196 QCA_WLAN_VENDOR_ATTR_SAR_LIMITS_SPEC_POWER_LIMIT = 7, 3197 QCA_WLAN_VENDOR_ATTR_SAR_LIMITS_SPEC_POWER_LIMIT_INDEX = 8, 3198 3199 QCA_WLAN_VENDOR_ATTR_SAR_LIMITS_AFTER_LAST, 3200 QCA_WLAN_VENDOR_ATTR_SAR_LIMITS_MAX = 3201 QCA_WLAN_VENDOR_ATTR_SAR_LIMITS_AFTER_LAST - 1 3202 }; 3203 3204 /** 3205 * enum qca_wlan_vendor_attr_get_wifi_info: Attributes for data used by 3206 * QCA_NL80211_VENDOR_SUBCMD_GET_WIFI_INFO sub command. 3207 */ 3208 enum qca_wlan_vendor_attr_get_wifi_info { 3209 QCA_WLAN_VENDOR_ATTR_WIFI_INFO_GET_INVALID = 0, 3210 QCA_WLAN_VENDOR_ATTR_WIFI_INFO_DRIVER_VERSION = 1, 3211 QCA_WLAN_VENDOR_ATTR_WIFI_INFO_FIRMWARE_VERSION = 2, 3212 3213 /* keep last */ 3214 QCA_WLAN_VENDOR_ATTR_WIFI_INFO_GET_AFTER_LAST, 3215 QCA_WLAN_VENDOR_ATTR_WIFI_INFO_GET_MAX = 3216 QCA_WLAN_VENDOR_ATTR_WIFI_INFO_GET_AFTER_LAST - 1, 3217 }; 3218 3219 /* 3220 * enum qca_wlan_vendor_attr_wifi_logger_start: Attributes for data used by 3221 * QCA_NL80211_VENDOR_SUBCMD_WIFI_LOGGER_START sub command. 3222 */ 3223 enum qca_wlan_vendor_attr_wifi_logger_start { 3224 QCA_WLAN_VENDOR_ATTR_WIFI_LOGGER_START_INVALID = 0, 3225 QCA_WLAN_VENDOR_ATTR_WIFI_LOGGER_RING_ID = 1, 3226 QCA_WLAN_VENDOR_ATTR_WIFI_LOGGER_VERBOSE_LEVEL = 2, 3227 QCA_WLAN_VENDOR_ATTR_WIFI_LOGGER_FLAGS = 3, 3228 3229 /* keep last */ 3230 QCA_WLAN_VENDOR_ATTR_WIFI_LOGGER_START_AFTER_LAST, 3231 QCA_WLAN_VENDOR_ATTR_WIFI_LOGGER_START_GET_MAX = 3232 QCA_WLAN_VENDOR_ATTR_WIFI_LOGGER_START_AFTER_LAST - 1, 3233 }; 3234 3235 enum qca_wlan_vendor_attr_logger_results { 3236 QCA_WLAN_VENDOR_ATTR_LOGGER_RESULTS_INVALID = 0, 3237 3238 /* Unsigned 32-bit value; must match the request Id supplied by 3239 * Wi-Fi HAL in the corresponding subcmd NL msg. 3240 */ 3241 QCA_WLAN_VENDOR_ATTR_LOGGER_RESULTS_REQUEST_ID = 1, 3242 3243 /* Unsigned 32-bit value; used to indicate the size of memory 3244 * dump to be allocated. 3245 */ 3246 QCA_WLAN_VENDOR_ATTR_LOGGER_RESULTS_MEMDUMP_SIZE = 2, 3247 3248 /* keep last */ 3249 QCA_WLAN_VENDOR_ATTR_LOGGER_RESULTS_AFTER_LAST, 3250 QCA_WLAN_VENDOR_ATTR_LOGGER_RESULTS_MAX = 3251 QCA_WLAN_VENDOR_ATTR_LOGGER_RESULTS_AFTER_LAST - 1, 3252 }; 3253 3254 enum qca_wlan_vendor_attr_roaming_config_params { 3255 QCA_WLAN_VENDOR_ATTR_ROAMING_PARAM_INVALID = 0, 3256 3257 QCA_WLAN_VENDOR_ATTR_ROAMING_SUBCMD = 1, 3258 QCA_WLAN_VENDOR_ATTR_ROAMING_REQ_ID = 2, 3259 3260 /* Attributes for wifi_set_ssid_white_list */ 3261 QCA_WLAN_VENDOR_ATTR_ROAMING_PARAM_WHITE_LIST_SSID_NUM_NETWORKS = 3, 3262 QCA_WLAN_VENDOR_ATTR_ROAMING_PARAM_WHITE_LIST_SSID_LIST = 4, 3263 QCA_WLAN_VENDOR_ATTR_ROAMING_PARAM_WHITE_LIST_SSID = 5, 3264 3265 /* Attributes for set_roam_params */ 3266 QCA_WLAN_VENDOR_ATTR_ROAMING_PARAM_A_BAND_BOOST_THRESHOLD = 6, 3267 QCA_WLAN_VENDOR_ATTR_ROAMING_PARAM_A_BAND_PENALTY_THRESHOLD = 7, 3268 QCA_WLAN_VENDOR_ATTR_ROAMING_PARAM_A_BAND_BOOST_FACTOR = 8, 3269 QCA_WLAN_VENDOR_ATTR_ROAMING_PARAM_A_BAND_PENALTY_FACTOR = 9, 3270 QCA_WLAN_VENDOR_ATTR_ROAMING_PARAM_A_BAND_MAX_BOOST = 10, 3271 QCA_WLAN_VENDOR_ATTR_ROAMING_PARAM_LAZY_ROAM_HISTERESYS = 11, 3272 QCA_WLAN_VENDOR_ATTR_ROAMING_PARAM_ALERT_ROAM_RSSI_TRIGGER = 12, 3273 3274 /* Attribute for set_lazy_roam */ 3275 QCA_WLAN_VENDOR_ATTR_ROAMING_PARAM_SET_LAZY_ROAM_ENABLE = 13, 3276 3277 /* Attribute for set_lazy_roam with preferences */ 3278 QCA_WLAN_VENDOR_ATTR_ROAMING_PARAM_SET_BSSID_PREFS = 14, 3279 QCA_WLAN_VENDOR_ATTR_ROAMING_PARAM_SET_LAZY_ROAM_NUM_BSSID = 15, 3280 QCA_WLAN_VENDOR_ATTR_ROAMING_PARAM_SET_LAZY_ROAM_BSSID = 16, 3281 QCA_WLAN_VENDOR_ATTR_ROAMING_PARAM_SET_LAZY_ROAM_RSSI_MODIFIER = 17, 3282 3283 /* Attribute for set_blacklist bssid params */ 3284 QCA_WLAN_VENDOR_ATTR_ROAMING_PARAM_SET_BSSID_PARAMS = 18, 3285 QCA_WLAN_VENDOR_ATTR_ROAMING_PARAM_SET_BSSID_PARAMS_NUM_BSSID = 19, 3286 QCA_WLAN_VENDOR_ATTR_ROAMING_PARAM_SET_BSSID_PARAMS_BSSID = 20, 3287 /* Flag attribute indicates this BSSID blacklist as a hint */ 3288 QCA_WLAN_VENDOR_ATTR_ROAMING_PARAM_SET_BSSID_PARAMS_HINT = 21, 3289 3290 /* keep last */ 3291 QCA_WLAN_VENDOR_ATTR_ROAMING_PARAM_AFTER_LAST, 3292 QCA_WLAN_VENDOR_ATTR_ROAMING_PARAM_MAX = 3293 QCA_WLAN_VENDOR_ATTR_ROAMING_PARAM_AFTER_LAST - 1, 3294 }; 3295 3296 /* 3297 * enum qca_wlan_vendor_attr_roam_subcmd: Attributes for data used by 3298 * QCA_NL80211_VENDOR_SUBCMD_ROAM sub command. 3299 */ 3300 enum qca_wlan_vendor_attr_roam_subcmd { 3301 QCA_WLAN_VENDOR_ATTR_ROAM_SUBCMD_INVALID = 0, 3302 QCA_WLAN_VENDOR_ATTR_ROAM_SUBCMD_SSID_WHITE_LIST = 1, 3303 QCA_WLAN_VENDOR_ATTR_ROAM_SUBCMD_SET_GSCAN_ROAM_PARAMS = 2, 3304 QCA_WLAN_VENDOR_ATTR_ROAM_SUBCMD_SET_LAZY_ROAM = 3, 3305 QCA_WLAN_VENDOR_ATTR_ROAM_SUBCMD_SET_BSSID_PREFS = 4, 3306 QCA_WLAN_VENDOR_ATTR_ROAM_SUBCMD_SET_BSSID_PARAMS = 5, 3307 QCA_WLAN_VENDOR_ATTR_ROAM_SUBCMD_SET_BLACKLIST_BSSID = 6, 3308 3309 /* keep last */ 3310 QCA_WLAN_VENDOR_ATTR_ROAM_SUBCMD_AFTER_LAST, 3311 QCA_WLAN_VENDOR_ATTR_ROAM_SUBCMD_MAX = 3312 QCA_WLAN_VENDOR_ATTR_ROAM_SUBCMD_AFTER_LAST - 1, 3313 }; 3314 3315 enum qca_wlan_vendor_attr_gscan_config_params { 3316 QCA_WLAN_VENDOR_ATTR_GSCAN_SUBCMD_CONFIG_PARAM_INVALID = 0, 3317 3318 /* Unsigned 32-bit value */ 3319 QCA_WLAN_VENDOR_ATTR_GSCAN_SUBCMD_CONFIG_PARAM_REQUEST_ID = 1, 3320 3321 /* Attributes for data used by 3322 * QCA_NL80211_VENDOR_SUBCMD_GSCAN_GET_VALID_CHANNELS sub command. 3323 */ 3324 /* Unsigned 32-bit value */ 3325 QCA_WLAN_VENDOR_ATTR_GSCAN_GET_VALID_CHANNELS_CONFIG_PARAM_WIFI_BAND 3326 = 2, 3327 /* Unsigned 32-bit value */ 3328 QCA_WLAN_VENDOR_ATTR_GSCAN_GET_VALID_CHANNELS_CONFIG_PARAM_MAX_CHANNELS 3329 = 3, 3330 3331 /* Attributes for input params used by 3332 * QCA_NL80211_VENDOR_SUBCMD_GSCAN_START sub command. 3333 */ 3334 3335 /* Unsigned 32-bit value; channel frequency */ 3336 QCA_WLAN_VENDOR_ATTR_GSCAN_CHANNEL_SPEC_CHANNEL = 4, 3337 /* Unsigned 32-bit value; dwell time in ms. */ 3338 QCA_WLAN_VENDOR_ATTR_GSCAN_CHANNEL_SPEC_DWELL_TIME = 5, 3339 /* Unsigned 8-bit value; 0: active; 1: passive; N/A for DFS */ 3340 QCA_WLAN_VENDOR_ATTR_GSCAN_CHANNEL_SPEC_PASSIVE = 6, 3341 /* Unsigned 8-bit value; channel class */ 3342 QCA_WLAN_VENDOR_ATTR_GSCAN_CHANNEL_SPEC_CLASS = 7, 3343 3344 /* Unsigned 8-bit value; bucket index, 0 based */ 3345 QCA_WLAN_VENDOR_ATTR_GSCAN_BUCKET_SPEC_INDEX = 8, 3346 /* Unsigned 8-bit value; band. */ 3347 QCA_WLAN_VENDOR_ATTR_GSCAN_BUCKET_SPEC_BAND = 9, 3348 /* Unsigned 32-bit value; desired period, in ms. */ 3349 QCA_WLAN_VENDOR_ATTR_GSCAN_BUCKET_SPEC_PERIOD = 10, 3350 /* Unsigned 8-bit value; report events semantics. */ 3351 QCA_WLAN_VENDOR_ATTR_GSCAN_BUCKET_SPEC_REPORT_EVENTS = 11, 3352 /* Unsigned 32-bit value. Followed by a nested array of 3353 * GSCAN_CHANNEL_SPEC_* attributes. 3354 */ 3355 QCA_WLAN_VENDOR_ATTR_GSCAN_BUCKET_SPEC_NUM_CHANNEL_SPECS = 12, 3356 3357 /* Array of QCA_WLAN_VENDOR_ATTR_GSCAN_CHANNEL_SPEC_* attributes. 3358 * Array size: QCA_WLAN_VENDOR_ATTR_GSCAN_BUCKET_SPEC_NUM_CHANNEL_SPECS 3359 */ 3360 QCA_WLAN_VENDOR_ATTR_GSCAN_CHANNEL_SPEC = 13, 3361 3362 /* Unsigned 32-bit value; base timer period in ms. */ 3363 QCA_WLAN_VENDOR_ATTR_GSCAN_SCAN_CMD_PARAMS_BASE_PERIOD = 14, 3364 /* Unsigned 32-bit value; number of APs to store in each scan in the 3365 * BSSID/RSSI history buffer (keep the highest RSSI APs). 3366 */ 3367 QCA_WLAN_VENDOR_ATTR_GSCAN_SCAN_CMD_PARAMS_MAX_AP_PER_SCAN = 15, 3368 /* Unsigned 8-bit value; in %, when scan buffer is this much full, wake 3369 * up AP. 3370 */ 3371 QCA_WLAN_VENDOR_ATTR_GSCAN_SCAN_CMD_PARAMS_REPORT_THRESHOLD_PERCENT 3372 = 16, 3373 3374 /* Unsigned 8-bit value; number of scan bucket specs; followed by a 3375 * nested array of_GSCAN_BUCKET_SPEC_* attributes and values. The size 3376 * of the array is determined by NUM_BUCKETS. 3377 */ 3378 QCA_WLAN_VENDOR_ATTR_GSCAN_SCAN_CMD_PARAMS_NUM_BUCKETS = 17, 3379 3380 /* Array of QCA_WLAN_VENDOR_ATTR_GSCAN_BUCKET_SPEC_* attributes. 3381 * Array size: QCA_WLAN_VENDOR_ATTR_GSCAN_SCAN_CMD_PARAMS_NUM_BUCKETS 3382 */ 3383 QCA_WLAN_VENDOR_ATTR_GSCAN_BUCKET_SPEC = 18, 3384 3385 /* Unsigned 8-bit value */ 3386 QCA_WLAN_VENDOR_ATTR_GSCAN_GET_CACHED_SCAN_RESULTS_CONFIG_PARAM_FLUSH 3387 = 19, 3388 /* Unsigned 32-bit value; maximum number of results to be returned. */ 3389 QCA_WLAN_VENDOR_ATTR_GSCAN_GET_CACHED_SCAN_RESULTS_CONFIG_PARAM_MAX 3390 = 20, 3391 3392 /* An array of 6 x unsigned 8-bit value */ 3393 QCA_WLAN_VENDOR_ATTR_GSCAN_AP_THRESHOLD_PARAM_BSSID = 21, 3394 /* Signed 32-bit value */ 3395 QCA_WLAN_VENDOR_ATTR_GSCAN_AP_THRESHOLD_PARAM_RSSI_LOW = 22, 3396 /* Signed 32-bit value */ 3397 QCA_WLAN_VENDOR_ATTR_GSCAN_AP_THRESHOLD_PARAM_RSSI_HIGH = 23, 3398 /* Unsigned 32-bit value */ 3399 QCA_WLAN_VENDOR_ATTR_GSCAN_AP_THRESHOLD_PARAM_CHANNEL = 24, 3400 3401 /* Number of hotlist APs as unsigned 32-bit value, followed by a nested 3402 * array of AP_THRESHOLD_PARAM attributes and values. The size of the 3403 * array is determined by NUM_AP. 3404 */ 3405 QCA_WLAN_VENDOR_ATTR_GSCAN_BSSID_HOTLIST_PARAMS_NUM_AP = 25, 3406 3407 /* Array of QCA_WLAN_VENDOR_ATTR_GSCAN_AP_THRESHOLD_PARAM_* attributes. 3408 * Array size: QCA_WLAN_VENDOR_ATTR_GSCAN_BUCKET_SPEC_NUM_CHANNEL_SPECS 3409 */ 3410 QCA_WLAN_VENDOR_ATTR_GSCAN_AP_THRESHOLD_PARAM = 26, 3411 3412 /* Unsigned 32-bit value; number of samples for averaging RSSI. */ 3413 QCA_WLAN_VENDOR_ATTR_GSCAN_SIGNIFICANT_CHANGE_PARAMS_RSSI_SAMPLE_SIZE 3414 = 27, 3415 /* Unsigned 32-bit value; number of samples to confirm AP loss. */ 3416 QCA_WLAN_VENDOR_ATTR_GSCAN_SIGNIFICANT_CHANGE_PARAMS_LOST_AP_SAMPLE_SIZE 3417 = 28, 3418 /* Unsigned 32-bit value; number of APs breaching threshold. */ 3419 QCA_WLAN_VENDOR_ATTR_GSCAN_SIGNIFICANT_CHANGE_PARAMS_MIN_BREACHING = 29, 3420 /* Unsigned 32-bit value; number of APs. Followed by an array of 3421 * AP_THRESHOLD_PARAM attributes. Size of the array is NUM_AP. 3422 */ 3423 QCA_WLAN_VENDOR_ATTR_GSCAN_SIGNIFICANT_CHANGE_PARAMS_NUM_AP = 30, 3424 /* Unsigned 32-bit value; number of samples to confirm AP loss. */ 3425 QCA_WLAN_VENDOR_ATTR_GSCAN_BSSID_HOTLIST_PARAMS_LOST_AP_SAMPLE_SIZE 3426 = 31, 3427 /* Unsigned 32-bit value. If max_period is non zero or different than 3428 * period, then this bucket is an exponential backoff bucket. 3429 */ 3430 QCA_WLAN_VENDOR_ATTR_GSCAN_BUCKET_SPEC_MAX_PERIOD = 32, 3431 /* Unsigned 32-bit value. */ 3432 QCA_WLAN_VENDOR_ATTR_GSCAN_BUCKET_SPEC_BASE = 33, 3433 /* Unsigned 32-bit value. For exponential back off bucket, number of 3434 * scans to perform for a given period. 3435 */ 3436 QCA_WLAN_VENDOR_ATTR_GSCAN_BUCKET_SPEC_STEP_COUNT = 34, 3437 /* Unsigned 8-bit value; in number of scans, wake up AP after these 3438 * many scans. 3439 */ 3440 QCA_WLAN_VENDOR_ATTR_GSCAN_SCAN_CMD_PARAMS_REPORT_THRESHOLD_NUM_SCANS 3441 = 35, 3442 3443 /* Attributes for data used by 3444 * QCA_NL80211_VENDOR_SUBCMD_GSCAN_SET_SSID_HOTLIST sub command. 3445 */ 3446 /* Unsigned 3-2bit value; number of samples to confirm SSID loss. */ 3447 QCA_WLAN_VENDOR_ATTR_GSCAN_SSID_HOTLIST_PARAMS_LOST_SSID_SAMPLE_SIZE 3448 = 36, 3449 /* Number of hotlist SSIDs as unsigned 32-bit value, followed by a 3450 * nested array of SSID_THRESHOLD_PARAM_* attributes and values. The 3451 * size of the array is determined by NUM_SSID. 3452 */ 3453 QCA_WLAN_VENDOR_ATTR_GSCAN_SSID_HOTLIST_PARAMS_NUM_SSID = 37, 3454 /* Array of QCA_WLAN_VENDOR_ATTR_GSCAN_SSID_THRESHOLD_PARAM_* 3455 * attributes. 3456 * Array size: QCA_WLAN_VENDOR_ATTR_GSCAN_SSID_HOTLIST_PARAMS_NUM_SSID 3457 */ 3458 QCA_WLAN_VENDOR_ATTR_GSCAN_SSID_THRESHOLD_PARAM = 38, 3459 3460 /* An array of 33 x unsigned 8-bit value; NULL terminated SSID */ 3461 QCA_WLAN_VENDOR_ATTR_GSCAN_SSID_THRESHOLD_PARAM_SSID = 39, 3462 /* Unsigned 8-bit value */ 3463 QCA_WLAN_VENDOR_ATTR_GSCAN_SSID_THRESHOLD_PARAM_BAND = 40, 3464 /* Signed 32-bit value */ 3465 QCA_WLAN_VENDOR_ATTR_GSCAN_SSID_THRESHOLD_PARAM_RSSI_LOW = 41, 3466 /* Signed 32-bit value */ 3467 QCA_WLAN_VENDOR_ATTR_GSCAN_SSID_THRESHOLD_PARAM_RSSI_HIGH = 42, 3468 /* Unsigned 32-bit value; a bitmask with additional gscan config flag. 3469 */ 3470 QCA_WLAN_VENDOR_ATTR_GSCAN_CONFIGURATION_FLAGS = 43, 3471 3472 /* keep last */ 3473 QCA_WLAN_VENDOR_ATTR_GSCAN_SUBCMD_CONFIG_PARAM_AFTER_LAST, 3474 QCA_WLAN_VENDOR_ATTR_GSCAN_SUBCMD_CONFIG_PARAM_MAX = 3475 QCA_WLAN_VENDOR_ATTR_GSCAN_SUBCMD_CONFIG_PARAM_AFTER_LAST - 1, 3476 }; 3477 3478 enum qca_wlan_vendor_attr_gscan_results { 3479 QCA_WLAN_VENDOR_ATTR_GSCAN_RESULTS_INVALID = 0, 3480 3481 /* Unsigned 32-bit value; must match the request Id supplied by 3482 * Wi-Fi HAL in the corresponding subcmd NL msg. 3483 */ 3484 QCA_WLAN_VENDOR_ATTR_GSCAN_RESULTS_REQUEST_ID = 1, 3485 3486 /* Unsigned 32-bit value; used to indicate the status response from 3487 * firmware/driver for the vendor sub-command. 3488 */ 3489 QCA_WLAN_VENDOR_ATTR_GSCAN_STATUS = 2, 3490 3491 /* GSCAN Valid Channels attributes */ 3492 /* Unsigned 32bit value; followed by a nested array of CHANNELS. */ 3493 QCA_WLAN_VENDOR_ATTR_GSCAN_RESULTS_NUM_CHANNELS = 3, 3494 /* An array of NUM_CHANNELS x unsigned 32-bit value integers 3495 * representing channel numbers. 3496 */ 3497 QCA_WLAN_VENDOR_ATTR_GSCAN_RESULTS_CHANNELS = 4, 3498 3499 /* GSCAN Capabilities attributes */ 3500 /* Unsigned 32-bit value */ 3501 QCA_WLAN_VENDOR_ATTR_GSCAN_RESULTS_CAPABILITIES_MAX_SCAN_CACHE_SIZE = 5, 3502 /* Unsigned 32-bit value */ 3503 QCA_WLAN_VENDOR_ATTR_GSCAN_RESULTS_CAPABILITIES_MAX_SCAN_BUCKETS = 6, 3504 /* Unsigned 32-bit value */ 3505 QCA_WLAN_VENDOR_ATTR_GSCAN_RESULTS_CAPABILITIES_MAX_AP_CACHE_PER_SCAN 3506 = 7, 3507 /* Unsigned 32-bit value */ 3508 QCA_WLAN_VENDOR_ATTR_GSCAN_RESULTS_CAPABILITIES_MAX_RSSI_SAMPLE_SIZE 3509 = 8, 3510 /* Signed 32-bit value */ 3511 QCA_WLAN_VENDOR_ATTR_GSCAN_RESULTS_CAPABILITIES_MAX_SCAN_REPORTING_THRESHOLD 3512 = 9, 3513 /* Unsigned 32-bit value */ 3514 QCA_WLAN_VENDOR_ATTR_GSCAN_RESULTS_CAPABILITIES_MAX_HOTLIST_BSSIDS = 10, 3515 /* Unsigned 32-bit value */ 3516 QCA_WLAN_VENDOR_ATTR_GSCAN_RESULTS_CAPABILITIES_MAX_SIGNIFICANT_WIFI_CHANGE_APS 3517 = 11, 3518 /* Unsigned 32-bit value */ 3519 QCA_WLAN_VENDOR_ATTR_GSCAN_RESULTS_CAPABILITIES_MAX_BSSID_HISTORY_ENTRIES 3520 = 12, 3521 3522 /* GSCAN Attributes used with 3523 * QCA_NL80211_VENDOR_SUBCMD_GSCAN_SCAN_RESULTS_AVAILABLE sub-command. 3524 */ 3525 3526 /* Unsigned 32-bit value */ 3527 QCA_WLAN_VENDOR_ATTR_GSCAN_RESULTS_NUM_RESULTS_AVAILABLE = 13, 3528 3529 /* GSCAN attributes used with 3530 * QCA_NL80211_VENDOR_SUBCMD_GSCAN_FULL_SCAN_RESULT sub-command. 3531 */ 3532 3533 /* An array of NUM_RESULTS_AVAILABLE x 3534 * QCA_WLAN_VENDOR_ATTR_GSCAN_RESULTS_SCAN_RESULT_* 3535 */ 3536 QCA_WLAN_VENDOR_ATTR_GSCAN_RESULTS_LIST = 14, 3537 3538 /* Unsigned 64-bit value; age of sample at the time of retrieval */ 3539 QCA_WLAN_VENDOR_ATTR_GSCAN_RESULTS_SCAN_RESULT_TIME_STAMP = 15, 3540 /* 33 x unsigned 8-bit value; NULL terminated SSID */ 3541 QCA_WLAN_VENDOR_ATTR_GSCAN_RESULTS_SCAN_RESULT_SSID = 16, 3542 /* An array of 6 x unsigned 8-bit value */ 3543 QCA_WLAN_VENDOR_ATTR_GSCAN_RESULTS_SCAN_RESULT_BSSID = 17, 3544 /* Unsigned 32-bit value; channel frequency in MHz */ 3545 QCA_WLAN_VENDOR_ATTR_GSCAN_RESULTS_SCAN_RESULT_CHANNEL = 18, 3546 /* Signed 32-bit value */ 3547 QCA_WLAN_VENDOR_ATTR_GSCAN_RESULTS_SCAN_RESULT_RSSI = 19, 3548 /* Unsigned 32-bit value */ 3549 QCA_WLAN_VENDOR_ATTR_GSCAN_RESULTS_SCAN_RESULT_RTT = 20, 3550 /* Unsigned 32-bit value */ 3551 QCA_WLAN_VENDOR_ATTR_GSCAN_RESULTS_SCAN_RESULT_RTT_SD = 21, 3552 /* Unsigned 16-bit value */ 3553 QCA_WLAN_VENDOR_ATTR_GSCAN_RESULTS_SCAN_RESULT_BEACON_PERIOD = 22, 3554 /* Unsigned 16-bit value */ 3555 QCA_WLAN_VENDOR_ATTR_GSCAN_RESULTS_SCAN_RESULT_CAPABILITY = 23, 3556 /* Unsigned 32-bit value; size of the IE DATA blob */ 3557 QCA_WLAN_VENDOR_ATTR_GSCAN_RESULTS_SCAN_RESULT_IE_LENGTH = 24, 3558 /* An array of IE_LENGTH x unsigned 8-bit value; blob of all the 3559 * information elements found in the beacon; this data should be a 3560 * packed list of wifi_information_element objects, one after the 3561 * other. 3562 */ 3563 QCA_WLAN_VENDOR_ATTR_GSCAN_RESULTS_SCAN_RESULT_IE_DATA = 25, 3564 3565 /* Unsigned 8-bit value; set by driver to indicate more scan results are 3566 * available. 3567 */ 3568 QCA_WLAN_VENDOR_ATTR_GSCAN_RESULTS_SCAN_RESULT_MORE_DATA = 26, 3569 3570 /* GSCAN attributes for 3571 * QCA_NL80211_VENDOR_SUBCMD_GSCAN_SCAN_EVENT sub-command. 3572 */ 3573 /* Unsigned 8-bit value */ 3574 QCA_WLAN_VENDOR_ATTR_GSCAN_RESULTS_SCAN_EVENT_TYPE = 27, 3575 /* Unsigned 32-bit value */ 3576 QCA_WLAN_VENDOR_ATTR_GSCAN_RESULTS_SCAN_EVENT_STATUS = 28, 3577 3578 /* GSCAN attributes for 3579 * QCA_NL80211_VENDOR_SUBCMD_GSCAN_HOTLIST_AP_FOUND sub-command. 3580 */ 3581 /* Use attr QCA_WLAN_VENDOR_ATTR_GSCAN_RESULTS_NUM_RESULTS_AVAILABLE 3582 * to indicate number of results. 3583 * Also, use QCA_WLAN_VENDOR_ATTR_GSCAN_RESULTS_LIST to indicate the 3584 * list of results. 3585 */ 3586 3587 /* GSCAN attributes for 3588 * QCA_NL80211_VENDOR_SUBCMD_GSCAN_SIGNIFICANT_CHANGE sub-command. 3589 */ 3590 /* An array of 6 x unsigned 8-bit value */ 3591 QCA_WLAN_VENDOR_ATTR_GSCAN_RESULTS_SIGNIFICANT_CHANGE_RESULT_BSSID = 29, 3592 /* Unsigned 32-bit value */ 3593 QCA_WLAN_VENDOR_ATTR_GSCAN_RESULTS_SIGNIFICANT_CHANGE_RESULT_CHANNEL 3594 = 30, 3595 /* Unsigned 32-bit value. */ 3596 QCA_WLAN_VENDOR_ATTR_GSCAN_RESULTS_SIGNIFICANT_CHANGE_RESULT_NUM_RSSI 3597 = 31, 3598 /* A nested array of signed 32-bit RSSI values. Size of the array is 3599 * determined by (NUM_RSSI of SIGNIFICANT_CHANGE_RESULT_NUM_RSSI. 3600 */ 3601 QCA_WLAN_VENDOR_ATTR_GSCAN_RESULTS_SIGNIFICANT_CHANGE_RESULT_RSSI_LIST 3602 = 32, 3603 3604 /* GSCAN attributes used with 3605 * QCA_NL80211_VENDOR_SUBCMD_GSCAN_GET_CACHED_RESULTS sub-command. 3606 */ 3607 /* Use attr QCA_WLAN_VENDOR_ATTR_GSCAN_RESULTS_NUM_RESULTS_AVAILABLE 3608 * to indicate number of gscan cached results returned. 3609 * Also, use QCA_WLAN_VENDOR_ATTR_GSCAN_CACHED_RESULTS_LIST to indicate 3610 * the list of gscan cached results. 3611 */ 3612 3613 /* An array of NUM_RESULTS_AVAILABLE x 3614 * QCA_NL80211_VENDOR_ATTR_GSCAN_CACHED_RESULTS_* 3615 */ 3616 QCA_WLAN_VENDOR_ATTR_GSCAN_CACHED_RESULTS_LIST = 33, 3617 /* Unsigned 32-bit value; a unique identifier for the scan unit. */ 3618 QCA_WLAN_VENDOR_ATTR_GSCAN_CACHED_RESULTS_SCAN_ID = 34, 3619 /* Unsigned 32-bit value; a bitmask w/additional information about scan. 3620 */ 3621 QCA_WLAN_VENDOR_ATTR_GSCAN_CACHED_RESULTS_FLAGS = 35, 3622 /* Use attr QCA_WLAN_VENDOR_ATTR_GSCAN_RESULTS_NUM_RESULTS_AVAILABLE 3623 * to indicate number of wifi scan results/bssids retrieved by the scan. 3624 * Also, use QCA_WLAN_VENDOR_ATTR_GSCAN_RESULTS_LIST to indicate the 3625 * list of wifi scan results returned for each cached result block. 3626 */ 3627 3628 /* GSCAN attributes for 3629 * QCA_NL80211_VENDOR_SUBCMD_PNO_NETWORK_FOUND sub-command. 3630 */ 3631 /* Use QCA_WLAN_VENDOR_ATTR_GSCAN_RESULTS_NUM_RESULTS_AVAILABLE for 3632 * number of results. 3633 * Use QCA_WLAN_VENDOR_ATTR_GSCAN_RESULTS_LIST to indicate the nested 3634 * list of wifi scan results returned for each 3635 * wifi_passpoint_match_result block. 3636 * Array size: QCA_WLAN_VENDOR_ATTR_GSCAN_RESULTS_NUM_RESULTS_AVAILABLE. 3637 */ 3638 3639 /* GSCAN attributes for 3640 * QCA_NL80211_VENDOR_SUBCMD_PNO_PASSPOINT_NETWORK_FOUND sub-command. 3641 */ 3642 /* Unsigned 32-bit value */ 3643 QCA_WLAN_VENDOR_ATTR_GSCAN_PNO_RESULTS_PASSPOINT_NETWORK_FOUND_NUM_MATCHES 3644 = 36, 3645 /* A nested array of 3646 * QCA_WLAN_VENDOR_ATTR_GSCAN_PNO_RESULTS_PASSPOINT_MATCH_* 3647 * attributes. Array size = 3648 * *_ATTR_GSCAN_PNO_RESULTS_PASSPOINT_NETWORK_FOUND_NUM_MATCHES. 3649 */ 3650 QCA_WLAN_VENDOR_ATTR_GSCAN_PNO_RESULTS_PASSPOINT_MATCH_RESULT_LIST = 37, 3651 3652 /* Unsigned 32-bit value; network block id for the matched network */ 3653 QCA_WLAN_VENDOR_ATTR_GSCAN_PNO_RESULTS_PASSPOINT_MATCH_ID = 38, 3654 /* Use QCA_WLAN_VENDOR_ATTR_GSCAN_RESULTS_LIST to indicate the nested 3655 * list of wifi scan results returned for each 3656 * wifi_passpoint_match_result block. 3657 */ 3658 /* Unsigned 32-bit value */ 3659 QCA_WLAN_VENDOR_ATTR_GSCAN_PNO_RESULTS_PASSPOINT_MATCH_ANQP_LEN = 39, 3660 /* An array size of PASSPOINT_MATCH_ANQP_LEN of unsigned 8-bit values; 3661 * ANQP data in the information_element format. 3662 */ 3663 QCA_WLAN_VENDOR_ATTR_GSCAN_PNO_RESULTS_PASSPOINT_MATCH_ANQP = 40, 3664 3665 /* Unsigned 32-bit value; a GSCAN Capabilities attribute. */ 3666 QCA_WLAN_VENDOR_ATTR_GSCAN_RESULTS_CAPABILITIES_MAX_HOTLIST_SSIDS = 41, 3667 /* Unsigned 32-bit value; a GSCAN Capabilities attribute. */ 3668 QCA_WLAN_VENDOR_ATTR_GSCAN_RESULTS_CAPABILITIES_MAX_NUM_EPNO_NETS = 42, 3669 /* Unsigned 32-bit value; a GSCAN Capabilities attribute. */ 3670 QCA_WLAN_VENDOR_ATTR_GSCAN_RESULTS_CAPABILITIES_MAX_NUM_EPNO_NETS_BY_SSID 3671 = 43, 3672 /* Unsigned 32-bit value; a GSCAN Capabilities attribute. */ 3673 QCA_WLAN_VENDOR_ATTR_GSCAN_RESULTS_CAPABILITIES_MAX_NUM_WHITELISTED_SSID 3674 = 44, 3675 3676 QCA_WLAN_VENDOR_ATTR_GSCAN_RESULTS_BUCKETS_SCANNED = 45, 3677 3678 /* Unsigned 32-bit value; a GSCAN Capabilities attribute. 3679 * This is used to limit the maximum number of BSSIDs while sending 3680 * the vendor command QCA_NL80211_VENDOR_SUBCMD_ROAM with attributes 3681 * QCA_WLAN_VENDOR_ATTR_ROAM_SUBCMD_SET_BLACKLIST_BSSID and 3682 * QCA_WLAN_VENDOR_ATTR_ROAMING_PARAM_SET_BSSID_PARAMS_NUM_BSSID. 3683 */ 3684 QCA_WLAN_VENDOR_ATTR_GSCAN_MAX_NUM_BLACKLISTED_BSSID = 46, 3685 3686 /* keep last */ 3687 QCA_WLAN_VENDOR_ATTR_GSCAN_RESULTS_AFTER_LAST, 3688 QCA_WLAN_VENDOR_ATTR_GSCAN_RESULTS_MAX = 3689 QCA_WLAN_VENDOR_ATTR_GSCAN_RESULTS_AFTER_LAST - 1, 3690 }; 3691 3692 enum qca_wlan_vendor_attr_pno_config_params { 3693 QCA_WLAN_VENDOR_ATTR_PNO_INVALID = 0, 3694 /* Attributes for data used by 3695 * QCA_NL80211_VENDOR_SUBCMD_PNO_SET_PASSPOINT_LIST sub command. 3696 */ 3697 /* Unsigned 32-bit value */ 3698 QCA_WLAN_VENDOR_ATTR_PNO_PASSPOINT_LIST_PARAM_NUM = 1, 3699 /* Array of nested QCA_WLAN_VENDOR_ATTR_PNO_PASSPOINT_NETWORK_PARAM_* 3700 * attributes. Array size = 3701 * QCA_WLAN_VENDOR_ATTR_PNO_PASSPOINT_LIST_PARAM_NUM. 3702 */ 3703 QCA_WLAN_VENDOR_ATTR_PNO_PASSPOINT_LIST_PARAM_NETWORK_ARRAY = 2, 3704 3705 /* Unsigned 32-bit value */ 3706 QCA_WLAN_VENDOR_ATTR_PNO_PASSPOINT_NETWORK_PARAM_ID = 3, 3707 /* An array of 256 x unsigned 8-bit value; NULL terminated UTF-8 encoded 3708 * realm, 0 if unspecified. 3709 */ 3710 QCA_WLAN_VENDOR_ATTR_PNO_PASSPOINT_NETWORK_PARAM_REALM = 4, 3711 /* An array of 16 x unsigned 32-bit value; roaming consortium ids to 3712 * match, 0 if unspecified. 3713 */ 3714 QCA_WLAN_VENDOR_ATTR_PNO_PASSPOINT_NETWORK_PARAM_ROAM_CNSRTM_ID = 5, 3715 /* An array of 6 x unsigned 8-bit value; MCC/MNC combination, 0s if 3716 * unspecified. 3717 */ 3718 QCA_WLAN_VENDOR_ATTR_PNO_PASSPOINT_NETWORK_PARAM_ROAM_PLMN = 6, 3719 3720 /* Attributes for data used by 3721 * QCA_NL80211_VENDOR_SUBCMD_PNO_SET_LIST sub command. 3722 */ 3723 /* Unsigned 32-bit value */ 3724 QCA_WLAN_VENDOR_ATTR_PNO_SET_LIST_PARAM_NUM_NETWORKS = 7, 3725 /* Array of nested 3726 * QCA_WLAN_VENDOR_ATTR_PNO_SET_LIST_PARAM_EPNO_NETWORK_* 3727 * attributes. Array size = 3728 * QCA_WLAN_VENDOR_ATTR_PNO_SET_LIST_PARAM_NUM_NETWORKS. 3729 */ 3730 QCA_WLAN_VENDOR_ATTR_PNO_SET_LIST_PARAM_EPNO_NETWORKS_LIST = 8, 3731 /* An array of 33 x unsigned 8-bit value; NULL terminated SSID */ 3732 QCA_WLAN_VENDOR_ATTR_PNO_SET_LIST_PARAM_EPNO_NETWORK_SSID = 9, 3733 /* Signed 8-bit value; threshold for considering this SSID as found, 3734 * required granularity for this threshold is 4 dBm to 8 dBm. 3735 */ 3736 QCA_WLAN_VENDOR_ATTR_PNO_SET_LIST_PARAM_EPNO_NETWORK_RSSI_THRESHOLD 3737 = 10, 3738 /* Unsigned 8-bit value; WIFI_PNO_FLAG_XXX */ 3739 QCA_WLAN_VENDOR_ATTR_PNO_SET_LIST_PARAM_EPNO_NETWORK_FLAGS = 11, 3740 /* Unsigned 8-bit value; auth bit field for matching WPA IE */ 3741 QCA_WLAN_VENDOR_ATTR_PNO_SET_LIST_PARAM_EPNO_NETWORK_AUTH_BIT = 12, 3742 /* Unsigned 8-bit to indicate ePNO type; 3743 * It takes values from qca_wlan_epno_type 3744 */ 3745 QCA_WLAN_VENDOR_ATTR_PNO_SET_LIST_PARAM_EPNO_TYPE = 13, 3746 3747 /* Nested attribute to send the channel list */ 3748 QCA_WLAN_VENDOR_ATTR_PNO_SET_LIST_PARAM_EPNO_CHANNEL_LIST = 14, 3749 3750 /* Unsigned 32-bit value; indicates the interval between PNO scan 3751 * cycles in msec. 3752 */ 3753 QCA_WLAN_VENDOR_ATTR_PNO_SET_LIST_PARAM_EPNO_SCAN_INTERVAL = 15, 3754 QCA_WLAN_VENDOR_ATTR_EPNO_MIN5GHZ_RSSI = 16, 3755 QCA_WLAN_VENDOR_ATTR_EPNO_MIN24GHZ_RSSI = 17, 3756 QCA_WLAN_VENDOR_ATTR_EPNO_INITIAL_SCORE_MAX = 18, 3757 QCA_WLAN_VENDOR_ATTR_EPNO_CURRENT_CONNECTION_BONUS = 19, 3758 QCA_WLAN_VENDOR_ATTR_EPNO_SAME_NETWORK_BONUS = 20, 3759 QCA_WLAN_VENDOR_ATTR_EPNO_SECURE_BONUS = 21, 3760 QCA_WLAN_VENDOR_ATTR_EPNO_BAND5GHZ_BONUS = 22, 3761 /* Unsigned 32-bit value, representing the PNO Request ID */ 3762 QCA_WLAN_VENDOR_ATTR_PNO_CONFIG_REQUEST_ID = 23, 3763 3764 /* keep last */ 3765 QCA_WLAN_VENDOR_ATTR_PNO_AFTER_LAST, 3766 QCA_WLAN_VENDOR_ATTR_PNO_MAX = 3767 QCA_WLAN_VENDOR_ATTR_PNO_AFTER_LAST - 1, 3768 }; 3769 3770 /** 3771 * qca_wlan_vendor_acs_select_reason: This represents the different reasons why 3772 * the ACS has to be triggered. These values are used by 3773 * QCA_WLAN_VENDOR_ATTR_EXTERNAL_ACS_EVENT_REASON and 3774 * QCA_WLAN_VENDOR_ATTR_EXTERNAL_ACS_CHANNEL_REASON 3775 */ 3776 enum qca_wlan_vendor_acs_select_reason { 3777 /* Represents the reason that the ACS triggered during the AP start */ 3778 QCA_WLAN_VENDOR_ACS_SELECT_REASON_INIT, 3779 /* Represents the reason that DFS found with the current channel */ 3780 QCA_WLAN_VENDOR_ACS_SELECT_REASON_DFS, 3781 /* Represents the reason that LTE co-exist in the current band. */ 3782 QCA_WLAN_VENDOR_ACS_SELECT_REASON_LTE_COEX, 3783 }; 3784 3785 /** 3786 * qca_wlan_vendor_attr_external_acs_policy: Attribute values for 3787 * QCA_WLAN_VENDOR_ATTR_EXTERNAL_ACS_EVENT_POLICY to the vendor subcmd 3788 * QCA_NL80211_VENDOR_SUBCMD_EXTERNAL_ACS. This represents the 3789 * external ACS policies to select the channels w.r.t. the PCL weights. 3790 * (QCA_WLAN_VENDOR_ATTR_EXTERNAL_ACS_EVENT_PCL represents the channels and 3791 * their PCL weights.) 3792 * @QCA_WLAN_VENDOR_ATTR_EXTERNAL_ACS_POLICY_PCL_MANDATORY: Mandatory to 3793 * select a channel with non-zero PCL weight. 3794 * @QCA_WLAN_VENDOR_ATTR_EXTERNAL_ACS_POLICY_PCL_PREFERRED: Prefer a 3795 * channel with non-zero PCL weight. 3796 * 3797 */ 3798 enum qca_wlan_vendor_attr_external_acs_policy { 3799 QCA_WLAN_VENDOR_ATTR_EXTERNAL_ACS_POLICY_PCL_PREFERRED, 3800 QCA_WLAN_VENDOR_ATTR_EXTERNAL_ACS_POLICY_PCL_MANDATORY, 3801 }; 3802 3803 /** 3804 * qca_wlan_vendor_channel_prop_flags: This represent the flags for a channel. 3805 * This is used by QCA_WLAN_VENDOR_EXTERNAL_ACS_EVENT_CHAN_INFO_ATTR_FLAGS. 3806 */ 3807 enum qca_wlan_vendor_channel_prop_flags { 3808 /* Bits 0, 1, 2, and 3 are reserved */ 3809 3810 /* Turbo channel */ 3811 QCA_WLAN_VENDOR_CHANNEL_PROP_FLAG_TURBO = 1 << 4, 3812 /* CCK channel */ 3813 QCA_WLAN_VENDOR_CHANNEL_PROP_FLAG_CCK = 1 << 5, 3814 /* OFDM channel */ 3815 QCA_WLAN_VENDOR_CHANNEL_PROP_FLAG_OFDM = 1 << 6, 3816 /* 2.4 GHz spectrum channel. */ 3817 QCA_WLAN_VENDOR_CHANNEL_PROP_FLAG_2GHZ = 1 << 7, 3818 /* 5 GHz spectrum channel */ 3819 QCA_WLAN_VENDOR_CHANNEL_PROP_FLAG_5GHZ = 1 << 8, 3820 /* Only passive scan allowed */ 3821 QCA_WLAN_VENDOR_CHANNEL_PROP_FLAG_PASSIVE = 1 << 9, 3822 /* Dynamic CCK-OFDM channel */ 3823 QCA_WLAN_VENDOR_CHANNEL_PROP_FLAG_DYN = 1 << 10, 3824 /* GFSK channel (FHSS PHY) */ 3825 QCA_WLAN_VENDOR_CHANNEL_PROP_FLAG_GFSK = 1 << 11, 3826 /* Radar found on channel */ 3827 QCA_WLAN_VENDOR_CHANNEL_PROP_FLAG_RADAR = 1 << 12, 3828 /* 11a static turbo channel only */ 3829 QCA_WLAN_VENDOR_CHANNEL_PROP_FLAG_STURBO = 1 << 13, 3830 /* Half rate channel */ 3831 QCA_WLAN_VENDOR_CHANNEL_PROP_FLAG_HALF = 1 << 14, 3832 /* Quarter rate channel */ 3833 QCA_WLAN_VENDOR_CHANNEL_PROP_FLAG_QUARTER = 1 << 15, 3834 /* HT 20 channel */ 3835 QCA_WLAN_VENDOR_CHANNEL_PROP_FLAG_HT20 = 1 << 16, 3836 /* HT 40 with extension channel above */ 3837 QCA_WLAN_VENDOR_CHANNEL_PROP_FLAG_HT40PLUS = 1 << 17, 3838 /* HT 40 with extension channel below */ 3839 QCA_WLAN_VENDOR_CHANNEL_PROP_FLAG_HT40MINUS = 1 << 18, 3840 /* HT 40 intolerant */ 3841 QCA_WLAN_VENDOR_CHANNEL_PROP_FLAG_HT40INTOL = 1 << 19, 3842 /* VHT 20 channel */ 3843 QCA_WLAN_VENDOR_CHANNEL_PROP_FLAG_VHT20 = 1 << 20, 3844 /* VHT 40 with extension channel above */ 3845 QCA_WLAN_VENDOR_CHANNEL_PROP_FLAG_VHT40PLUS = 1 << 21, 3846 /* VHT 40 with extension channel below */ 3847 QCA_WLAN_VENDOR_CHANNEL_PROP_FLAG_VHT40MINUS = 1 << 22, 3848 /* VHT 80 channel */ 3849 QCA_WLAN_VENDOR_CHANNEL_PROP_FLAG_VHT80 = 1 << 23, 3850 /* HT 40 intolerant mark bit for ACS use */ 3851 QCA_WLAN_VENDOR_CHANNEL_PROP_FLAG_HT40INTOLMARK = 1 << 24, 3852 /* Channel temporarily blocked due to noise */ 3853 QCA_WLAN_VENDOR_CHANNEL_PROP_FLAG_BLOCKED = 1 << 25, 3854 /* VHT 160 channel */ 3855 QCA_WLAN_VENDOR_CHANNEL_PROP_FLAG_VHT160 = 1 << 26, 3856 /* VHT 80+80 channel */ 3857 QCA_WLAN_VENDOR_CHANNEL_PROP_FLAG_VHT80_80 = 1 << 27, 3858 /* HE 20 channel */ 3859 QCA_WLAN_VENDOR_CHANNEL_PROP_FLAG_HE20 = 1 << 28, 3860 /* HE 40 with extension channel above */ 3861 QCA_WLAN_VENDOR_CHANNEL_PROP_FLAG_HE40PLUS = 1 << 29, 3862 /* HE 40 with extension channel below */ 3863 QCA_WLAN_VENDOR_CHANNEL_PROP_FLAG_HE40MINUS = 1 << 30, 3864 /* HE 40 intolerant */ 3865 QCA_WLAN_VENDOR_CHANNEL_PROP_FLAG_HE40INTOL = 1 << 31, 3866 }; 3867 3868 /** 3869 * qca_wlan_vendor_channel_prop_flags_2: This represents the flags for a 3870 * channel, and is a continuation of qca_wlan_vendor_channel_prop_flags. This is 3871 * used by QCA_WLAN_VENDOR_EXTERNAL_ACS_EVENT_CHAN_INFO_ATTR_FLAGS_2. 3872 */ 3873 enum qca_wlan_vendor_channel_prop_flags_2 { 3874 /* HE 40 intolerant mark bit for ACS use */ 3875 QCA_WLAN_VENDOR_CHANNEL_PROP_FLAG_HE40INTOLMARK = 1 << 0, 3876 /* HE 80 channel */ 3877 QCA_WLAN_VENDOR_CHANNEL_PROP_FLAG_HE80 = 1 << 1, 3878 /* HE 160 channel */ 3879 QCA_WLAN_VENDOR_CHANNEL_PROP_FLAG_HE160 = 1 << 2, 3880 /* HE 80+80 channel */ 3881 QCA_WLAN_VENDOR_CHANNEL_PROP_FLAG_HE80_80 = 1 << 3, 3882 }; 3883 3884 /** 3885 * qca_wlan_vendor_channel_prop_flags_ext: This represent the extended flags for 3886 * each channel. This is used by 3887 * QCA_WLAN_VENDOR_EXTERNAL_ACS_EVENT_CHAN_INFO_ATTR_FLAG_EXT. 3888 */ 3889 enum qca_wlan_vendor_channel_prop_flags_ext { 3890 /* Radar found on channel */ 3891 QCA_WLAN_VENDOR_CHANNEL_PROP_FLAG_EXT_RADAR_FOUND = 1 << 0, 3892 /* DFS required on channel */ 3893 QCA_WLAN_VENDOR_CHANNEL_PROP_FLAG_EXT_DFS = 1 << 1, 3894 /* DFS required on channel for 2nd band of 80+80 */ 3895 QCA_WLAN_VENDOR_CHANNEL_PROP_FLAG_EXT_DFS_CFREQ2 = 1 << 2, 3896 /* If channel has been checked for DFS */ 3897 QCA_WLAN_VENDOR_CHANNEL_PROP_FLAG_EXT_DFS_CLEAR = 1 << 3, 3898 /* Excluded in 802.11d */ 3899 QCA_WLAN_VENDOR_CHANNEL_PROP_FLAG_EXT_11D_EXCLUDED = 1 << 4, 3900 /* Channel Switch Announcement received on this channel */ 3901 QCA_WLAN_VENDOR_CHANNEL_PROP_FLAG_EXT_CSA_RECEIVED = 1 << 5, 3902 /* Ad-hoc is not allowed */ 3903 QCA_WLAN_VENDOR_CHANNEL_PROP_FLAG_EXT_DISALLOW_ADHOC = 1 << 6, 3904 /* Station only channel */ 3905 QCA_WLAN_VENDOR_CHANNEL_PROP_FLAG_EXT_DISALLOW_HOSTAP = 1 << 7, 3906 /* DFS radar history for slave device (STA mode) */ 3907 QCA_WLAN_VENDOR_CHANNEL_PROP_FLAG_EXT_HISTORY_RADAR = 1 << 8, 3908 /* DFS CAC valid for slave device (STA mode) */ 3909 QCA_WLAN_VENDOR_CHANNEL_PROP_FLAG_EXT_CAC_VALID = 1 << 9, 3910 }; 3911 3912 /** 3913 * qca_wlan_vendor_external_acs_event_chan_info_attr: Represents per channel 3914 * information. These attributes are sent as part of 3915 * QCA_WLAN_VENDOR_ATTR_EXTERNAL_ACS_EVENT_CHAN_INFO. Each set of the following 3916 * attributes correspond to a single channel. 3917 */ 3918 enum qca_wlan_vendor_external_acs_event_chan_info_attr { 3919 QCA_WLAN_VENDOR_EXTERNAL_ACS_EVENT_CHAN_INFO_ATTR_INVALID = 0, 3920 3921 /* A bitmask (u32) with flags specified in 3922 * enum qca_wlan_vendor_channel_prop_flags. 3923 */ 3924 QCA_WLAN_VENDOR_EXTERNAL_ACS_EVENT_CHAN_INFO_ATTR_FLAGS = 1, 3925 /* A bitmask (u32) with flags specified in 3926 * enum qca_wlan_vendor_channel_prop_flags_ext. 3927 */ 3928 QCA_WLAN_VENDOR_EXTERNAL_ACS_EVENT_CHAN_INFO_ATTR_FLAG_EXT = 2, 3929 /* frequency in MHz (u32) */ 3930 QCA_WLAN_VENDOR_EXTERNAL_ACS_EVENT_CHAN_INFO_ATTR_FREQ = 3, 3931 /* maximum regulatory transmission power (u32) */ 3932 QCA_WLAN_VENDOR_EXTERNAL_ACS_EVENT_CHAN_INFO_ATTR_MAX_REG_POWER = 4, 3933 /* maximum transmission power (u32) */ 3934 QCA_WLAN_VENDOR_EXTERNAL_ACS_EVENT_CHAN_INFO_ATTR_MAX_POWER = 5, 3935 /* minimum transmission power (u32) */ 3936 QCA_WLAN_VENDOR_EXTERNAL_ACS_EVENT_CHAN_INFO_ATTR_MIN_POWER = 6, 3937 /* regulatory class id (u8) */ 3938 QCA_WLAN_VENDOR_EXTERNAL_ACS_EVENT_CHAN_INFO_ATTR_REG_CLASS_ID = 7, 3939 /* maximum antenna gain in (u8) */ 3940 QCA_WLAN_VENDOR_EXTERNAL_ACS_EVENT_CHAN_INFO_ATTR_ANTENNA_GAIN = 8, 3941 /* VHT segment 0 (u8) */ 3942 QCA_WLAN_VENDOR_EXTERNAL_ACS_EVENT_CHAN_INFO_ATTR_VHT_SEG_0 = 9, 3943 /* VHT segment 1 (u8) */ 3944 QCA_WLAN_VENDOR_EXTERNAL_ACS_EVENT_CHAN_INFO_ATTR_VHT_SEG_1 = 10, 3945 /* A bitmask (u32) with flags specified in 3946 * enum qca_wlan_vendor_channel_prop_flags_2. 3947 */ 3948 QCA_WLAN_VENDOR_EXTERNAL_ACS_EVENT_CHAN_INFO_ATTR_FLAGS_2 = 11, 3949 3950 /* keep last */ 3951 QCA_WLAN_VENDOR_EXTERNAL_ACS_EVENT_CHAN_INFO_ATTR_LAST, 3952 QCA_WLAN_VENDOR_EXTERNAL_ACS_EVENT_CHAN_INFO_ATTR_MAX = 3953 QCA_WLAN_VENDOR_EXTERNAL_ACS_EVENT_CHAN_INFO_ATTR_LAST - 1, 3954 }; 3955 3956 /** 3957 * qca_wlan_vendor_attr_pcl: Represents attributes for 3958 * preferred channel list (PCL). These attributes are sent as part of 3959 * QCA_WLAN_VENDOR_ATTR_EXTERNAL_ACS_EVENT_PCL and 3960 * QCA_NL80211_VENDOR_SUBCMD_GET_PREFERRED_FREQ_LIST. 3961 */ 3962 enum qca_wlan_vendor_attr_pcl { 3963 QCA_WLAN_VENDOR_ATTR_PCL_INVALID = 0, 3964 3965 /* Channel number (u8) */ 3966 QCA_WLAN_VENDOR_ATTR_PCL_CHANNEL = 1, 3967 /* Channel weightage (u8) */ 3968 QCA_WLAN_VENDOR_ATTR_PCL_WEIGHT = 2, 3969 /* Channel frequency (u32) in MHz */ 3970 QCA_WLAN_VENDOR_ATTR_PCL_FREQ = 3, 3971 /* Channel flags (u32) 3972 * bit 0 set: channel to be used for GO role, 3973 * bit 1 set: channel to be used on CLI role, 3974 * bit 2 set: channel must be considered for operating channel 3975 * selection & peer chosen operating channel should be 3976 * one of the channels with this flag set, 3977 * bit 3 set: channel should be excluded in GO negotiation 3978 */ 3979 QCA_WLAN_VENDOR_ATTR_PCL_FLAG = 4, 3980 }; 3981 3982 /** 3983 * qca_wlan_vendor_attr_external_acs_event: Attribute to vendor sub-command 3984 * QCA_NL80211_VENDOR_SUBCMD_EXTERNAL_ACS. This attribute will be sent by 3985 * host driver. 3986 */ 3987 enum qca_wlan_vendor_attr_external_acs_event { 3988 QCA_WLAN_VENDOR_ATTR_EXTERNAL_ACS_EVENT_INVALID = 0, 3989 3990 /* This reason (u8) refers to enum qca_wlan_vendor_acs_select_reason. 3991 * This helps ACS module to understand why ACS needs to be started. 3992 */ 3993 QCA_WLAN_VENDOR_ATTR_EXTERNAL_ACS_EVENT_REASON = 1, 3994 /* Flag attribute to indicate if driver supports spectral scanning */ 3995 QCA_WLAN_VENDOR_ATTR_EXTERNAL_ACS_EVENT_IS_SPECTRAL_SUPPORTED = 2, 3996 /* Flag attribute to indicate if 11ac is offloaded to firmware */ 3997 QCA_WLAN_VENDOR_ATTR_EXTERNAL_ACS_EVENT_IS_OFFLOAD_ENABLED = 3, 3998 /* Flag attribute to indicate if driver provides additional channel 3999 * capability as part of scan operation 4000 */ 4001 QCA_WLAN_VENDOR_ATTR_EXTERNAL_ACS_EVENT_ADD_CHAN_STATS_SUPPORT = 4, 4002 /* Flag attribute to indicate interface status is UP */ 4003 QCA_WLAN_VENDOR_ATTR_EXTERNAL_ACS_EVENT_AP_UP = 5, 4004 /* Operating mode (u8) of interface. Takes one of enum nl80211_iftype 4005 * values. 4006 */ 4007 QCA_WLAN_VENDOR_ATTR_EXTERNAL_ACS_EVENT_SAP_MODE = 6, 4008 /* Channel width (u8). It takes one of enum nl80211_chan_width values. 4009 * This is the upper bound of channel width. ACS logic should try to get 4010 * a channel with the specified width and if not found, look for lower 4011 * values. 4012 */ 4013 QCA_WLAN_VENDOR_ATTR_EXTERNAL_ACS_EVENT_CHAN_WIDTH = 7, 4014 /* This (u8) will hold values of one of enum nl80211_bands */ 4015 QCA_WLAN_VENDOR_ATTR_EXTERNAL_ACS_EVENT_BAND = 8, 4016 /* PHY/HW mode (u8). Takes one of enum qca_wlan_vendor_acs_hw_mode 4017 * values 4018 */ 4019 QCA_WLAN_VENDOR_ATTR_EXTERNAL_ACS_EVENT_PHY_MODE = 9, 4020 /* Array of (u32) supported frequency list among which ACS should choose 4021 * best frequency. 4022 */ 4023 QCA_WLAN_VENDOR_ATTR_EXTERNAL_ACS_EVENT_FREQ_LIST = 10, 4024 /* Preferred channel list by the driver which will have array of nested 4025 * values as per enum qca_wlan_vendor_attr_pcl attribute. 4026 */ 4027 QCA_WLAN_VENDOR_ATTR_EXTERNAL_ACS_EVENT_PCL = 11, 4028 /* Array of nested attribute for each channel. It takes attr as defined 4029 * in enum qca_wlan_vendor_external_acs_event_chan_info_attr. 4030 */ 4031 QCA_WLAN_VENDOR_ATTR_EXTERNAL_ACS_EVENT_CHAN_INFO = 12, 4032 /* External ACS policy such as PCL mandatory, PCL preferred, etc. 4033 * It uses values defined in enum 4034 * qca_wlan_vendor_attr_external_acs_policy. 4035 */ 4036 QCA_WLAN_VENDOR_ATTR_EXTERNAL_ACS_EVENT_POLICY = 13, 4037 /* Reference RF Operating Parameter (RROP) availability information 4038 * (u16). It uses values defined in enum 4039 * qca_wlan_vendor_attr_rropavail_info. 4040 */ 4041 QCA_WLAN_VENDOR_ATTR_EXTERNAL_ACS_EVENT_RROPAVAIL_INFO = 14, 4042 4043 /* keep last */ 4044 QCA_WLAN_VENDOR_ATTR_EXTERNAL_ACS_EVENT_LAST, 4045 QCA_WLAN_VENDOR_ATTR_EXTERNAL_ACS_EVENT_MAX = 4046 QCA_WLAN_VENDOR_ATTR_EXTERNAL_ACS_EVENT_LAST - 1, 4047 }; 4048 4049 /** 4050 * qca_wlan_vendor_attr_external_acs_channels: Attributes to vendor subcmd 4051 * QCA_NL80211_VENDOR_SUBCMD_EXTERNAL_ACS. This carries a list of channels 4052 * in priority order as decided after ACS operation in userspace. 4053 */ 4054 enum qca_wlan_vendor_attr_external_acs_channels { 4055 QCA_WLAN_VENDOR_ATTR_EXTERNAL_ACS_CHANNEL_INVALID = 0, 4056 4057 /* One of reason code (u8) from enum qca_wlan_vendor_acs_select_reason 4058 */ 4059 QCA_WLAN_VENDOR_ATTR_EXTERNAL_ACS_CHANNEL_REASON = 1, 4060 4061 /* Array of nested values for each channel with following attributes: 4062 * QCA_WLAN_VENDOR_ATTR_EXTERNAL_ACS_CHANNEL_BAND, 4063 * QCA_WLAN_VENDOR_ATTR_EXTERNAL_ACS_CHANNEL_PRIMARY, 4064 * QCA_WLAN_VENDOR_ATTR_EXTERNAL_ACS_CHANNEL_SECONDARY, 4065 * QCA_WLAN_VENDOR_ATTR_EXTERNAL_ACS_CHANNEL_CENTER_SEG0, 4066 * QCA_WLAN_VENDOR_ATTR_EXTERNAL_ACS_CHANNEL_CENTER_SEG1, 4067 * QCA_WLAN_VENDOR_ATTR_EXTERNAL_ACS_CHANNEL_WIDTH 4068 */ 4069 QCA_WLAN_VENDOR_ATTR_EXTERNAL_ACS_CHANNEL_LIST = 2, 4070 /* This (u8) will hold values of one of enum nl80211_bands */ 4071 QCA_WLAN_VENDOR_ATTR_EXTERNAL_ACS_CHANNEL_BAND = 3, 4072 /* Primary channel (u8) */ 4073 QCA_WLAN_VENDOR_ATTR_EXTERNAL_ACS_CHANNEL_PRIMARY = 4, 4074 /* Secondary channel (u8) used for HT 40 MHz channels */ 4075 QCA_WLAN_VENDOR_ATTR_EXTERNAL_ACS_CHANNEL_SECONDARY = 5, 4076 /* VHT seg0 channel (u8) */ 4077 QCA_WLAN_VENDOR_ATTR_EXTERNAL_ACS_CHANNEL_CENTER_SEG0 = 6, 4078 /* VHT seg1 channel (u8) */ 4079 QCA_WLAN_VENDOR_ATTR_EXTERNAL_ACS_CHANNEL_CENTER_SEG1 = 7, 4080 /* Channel width (u8). Takes one of enum nl80211_chan_width values. */ 4081 QCA_WLAN_VENDOR_ATTR_EXTERNAL_ACS_CHANNEL_WIDTH = 8, 4082 4083 /* keep last */ 4084 QCA_WLAN_VENDOR_ATTR_EXTERNAL_ACS_CHANNEL_LAST, 4085 QCA_WLAN_VENDOR_ATTR_EXTERNAL_ACS_CHANNEL_MAX = 4086 QCA_WLAN_VENDOR_ATTR_EXTERNAL_ACS_CHANNEL_LAST - 1 4087 }; 4088 4089 enum qca_chip_power_save_failure_reason { 4090 /* Indicates if the reason for the failure is due to a protocol 4091 * layer/module. 4092 */ 4093 QCA_CHIP_POWER_SAVE_FAILURE_REASON_PROTOCOL = 0, 4094 /* Indicates if the reason for the failure is due to a hardware issue. 4095 */ 4096 QCA_CHIP_POWER_SAVE_FAILURE_REASON_HARDWARE = 1, 4097 }; 4098 4099 /** 4100 * qca_attr_chip_power_save_failure: Attributes to vendor subcmd 4101 * QCA_NL80211_VENDOR_SUBCMD_CHIP_PWRSAVE_FAILURE. This carries the requisite 4102 * information leading to the power save failure. 4103 */ 4104 enum qca_attr_chip_power_save_failure { 4105 QCA_ATTR_CHIP_POWER_SAVE_FAILURE_INVALID = 0, 4106 /* Reason to cause the power save failure. 4107 * These reasons are represented by 4108 * enum qca_chip_power_save_failure_reason. 4109 */ 4110 QCA_ATTR_CHIP_POWER_SAVE_FAILURE_REASON = 1, 4111 4112 /* keep last */ 4113 QCA_ATTR_CHIP_POWER_SAVE_FAILURE_LAST, 4114 QCA_ATTR_CHIP_POWER_SAVE_FAILURE_MAX = 4115 QCA_ATTR_CHIP_POWER_SAVE_FAILURE_LAST - 1, 4116 }; 4117 4118 /** 4119 * qca_wlan_vendor_nud_stats_data_pkt_flags: Flag representing the various 4120 * data types for which the stats have to get collected. 4121 */ 4122 enum qca_wlan_vendor_nud_stats_data_pkt_flags { 4123 QCA_WLAN_VENDOR_NUD_STATS_DATA_ARP = 1 << 0, 4124 QCA_WLAN_VENDOR_NUD_STATS_DATA_DNS = 1 << 1, 4125 QCA_WLAN_VENDOR_NUD_STATS_DATA_TCP_HANDSHAKE = 1 << 2, 4126 QCA_WLAN_VENDOR_NUD_STATS_DATA_ICMPV4 = 1 << 3, 4127 QCA_WLAN_VENDOR_NUD_STATS_DATA_ICMPV6 = 1 << 4, 4128 /* Used by QCA_ATTR_NUD_STATS_PKT_TYPE only in nud stats get 4129 * to represent the stats of respective data type. 4130 */ 4131 QCA_WLAN_VENDOR_NUD_STATS_DATA_TCP_SYN = 1 << 5, 4132 QCA_WLAN_VENDOR_NUD_STATS_DATA_TCP_SYN_ACK = 1 << 6, 4133 QCA_WLAN_VENDOR_NUD_STATS_DATA_TCP_ACK = 1 << 7, 4134 }; 4135 4136 enum qca_wlan_vendor_nud_stats_set_data_pkt_info { 4137 QCA_ATTR_NUD_STATS_DATA_PKT_INFO_INVALID = 0, 4138 /* Represents the data packet type to be monitored (u32). 4139 * Host driver tracks the stats corresponding to each data frame 4140 * represented by these flags. 4141 * These data packets are represented by 4142 * enum qca_wlan_vendor_nud_stats_data_pkt_flags 4143 */ 4144 QCA_ATTR_NUD_STATS_DATA_PKT_INFO_TYPE = 1, 4145 /* Name corresponding to the DNS frame for which the respective DNS 4146 * stats have to get monitored (string). Max string length 255. 4147 */ 4148 QCA_ATTR_NUD_STATS_DATA_PKT_INFO_DNS_DOMAIN_NAME = 2, 4149 /* source port on which the respective proto stats have to get 4150 * collected (u32). 4151 */ 4152 QCA_ATTR_NUD_STATS_DATA_PKT_INFO_SRC_PORT = 3, 4153 /* destination port on which the respective proto stats have to get 4154 * collected (u32). 4155 */ 4156 QCA_ATTR_NUD_STATS_DATA_PKT_INFO_DEST_PORT = 4, 4157 /* IPv4 address for which the destined data packets have to be 4158 * monitored. (in network byte order), u32. 4159 */ 4160 QCA_ATTR_NUD_STATS_DATA_PKT_INFO_DEST_IPV4 = 5, 4161 /* IPv6 address for which the destined data packets have to be 4162 * monitored. (in network byte order), 16 bytes array. 4163 */ 4164 QCA_ATTR_NUD_STATS_DATA_PKT_INFO_DEST_IPV6 = 6, 4165 4166 QCA_ATTR_NUD_STATS_DATA_PKT_INFO_LAST, 4167 QCA_ATTR_NUD_STATS_DATA_PKT_INFO_MAX = 4168 QCA_ATTR_NUD_STATS_DATA_PKT_INFO_LAST - 1, 4169 }; 4170 4171 /** 4172 * qca_wlan_vendor_attr_nud_stats_set: Attributes to vendor subcmd 4173 * QCA_NL80211_VENDOR_SUBCMD_NUD_STATS_SET. This carries the requisite 4174 * information to start/stop the NUD statistics collection. 4175 */ 4176 enum qca_attr_nud_stats_set { 4177 QCA_ATTR_NUD_STATS_SET_INVALID = 0, 4178 4179 /* Flag to start/stop the NUD statistics collection. 4180 * Start - If included, Stop - If not included 4181 */ 4182 QCA_ATTR_NUD_STATS_SET_START = 1, 4183 /* IPv4 address of the default gateway (in network byte order), u32 */ 4184 QCA_ATTR_NUD_STATS_GW_IPV4 = 2, 4185 /* Represents the list of data packet types to be monitored. 4186 * Host driver tracks the stats corresponding to each data frame 4187 * represented by these flags. 4188 * These data packets are represented by 4189 * enum qca_wlan_vendor_nud_stats_set_data_pkt_info 4190 */ 4191 QCA_ATTR_NUD_STATS_SET_DATA_PKT_INFO = 3, 4192 4193 /* keep last */ 4194 QCA_ATTR_NUD_STATS_SET_LAST, 4195 QCA_ATTR_NUD_STATS_SET_MAX = 4196 QCA_ATTR_NUD_STATS_SET_LAST - 1, 4197 }; 4198 4199 enum qca_attr_nud_data_stats { 4200 QCA_ATTR_NUD_DATA_STATS_INVALID = 0, 4201 /* Data packet type for which the stats are collected (u32). 4202 * Represented by enum qca_wlan_vendor_nud_stats_data_pkt_flags 4203 */ 4204 QCA_ATTR_NUD_STATS_PKT_TYPE = 1, 4205 /* Name corresponding to the DNS frame for which the respective DNS 4206 * stats are monitored (string). Max string length 255. 4207 */ 4208 QCA_ATTR_NUD_STATS_PKT_DNS_DOMAIN_NAME = 2, 4209 /* source port on which the respective proto stats are collected (u32). 4210 */ 4211 QCA_ATTR_NUD_STATS_PKT_SRC_PORT = 3, 4212 /* destination port on which the respective proto stats are collected 4213 * (u32). 4214 */ 4215 QCA_ATTR_NUD_STATS_PKT_DEST_PORT = 4, 4216 /* IPv4 address for which the destined data packets have to be 4217 * monitored. (in network byte order), u32. 4218 */ 4219 QCA_ATTR_NUD_STATS_PKT_DEST_IPV4 = 5, 4220 /* IPv6 address for which the destined data packets have to be 4221 * monitored. (in network byte order), 16 bytes array. 4222 */ 4223 QCA_ATTR_NUD_STATS_PKT_DEST_IPV6 = 6, 4224 /* Data packet Request count received from netdev (u32). */ 4225 QCA_ATTR_NUD_STATS_PKT_REQ_COUNT_FROM_NETDEV = 7, 4226 /* Data packet Request count sent to lower MAC from upper MAC (u32). */ 4227 QCA_ATTR_NUD_STATS_PKT_REQ_COUNT_TO_LOWER_MAC = 8, 4228 /* Data packet Request count received by lower MAC from upper MAC 4229 * (u32) 4230 */ 4231 QCA_ATTR_NUD_STATS_PKT_REQ_RX_COUNT_BY_LOWER_MAC = 9, 4232 /* Data packet Request count successfully transmitted by the device 4233 * (u32) 4234 */ 4235 QCA_ATTR_NUD_STATS_PKT_REQ_COUNT_TX_SUCCESS = 10, 4236 /* Data packet Response count received by lower MAC (u32) */ 4237 QCA_ATTR_NUD_STATS_PKT_RSP_RX_COUNT_BY_LOWER_MAC = 11, 4238 /* Data packet Response count received by upper MAC (u32) */ 4239 QCA_ATTR_NUD_STATS_PKT_RSP_RX_COUNT_BY_UPPER_MAC = 12, 4240 /* Data packet Response count delivered to netdev (u32) */ 4241 QCA_ATTR_NUD_STATS_PKT_RSP_COUNT_TO_NETDEV = 13, 4242 /* Data Packet Response count that are dropped out of order (u32) */ 4243 QCA_ATTR_NUD_STATS_PKT_RSP_COUNT_OUT_OF_ORDER_DROP = 14, 4244 4245 /* keep last */ 4246 QCA_ATTR_NUD_DATA_STATS_LAST, 4247 QCA_ATTR_NUD_DATA_STATS_MAX = 4248 QCA_ATTR_NUD_DATA_STATS_LAST - 1, 4249 }; 4250 4251 /** 4252 * qca_attr_nud_stats_get: Attributes to vendor subcmd 4253 * QCA_NL80211_VENDOR_SUBCMD_NUD_STATS_GET. This carries the requisite 4254 * NUD statistics collected when queried. 4255 */ 4256 enum qca_attr_nud_stats_get { 4257 QCA_ATTR_NUD_STATS_GET_INVALID = 0, 4258 /* ARP Request count from netdev (u32) */ 4259 QCA_ATTR_NUD_STATS_ARP_REQ_COUNT_FROM_NETDEV = 1, 4260 /* ARP Request count sent to lower MAC from upper MAC (u32) */ 4261 QCA_ATTR_NUD_STATS_ARP_REQ_COUNT_TO_LOWER_MAC = 2, 4262 /* ARP Request count received by lower MAC from upper MAC (u32) */ 4263 QCA_ATTR_NUD_STATS_ARP_REQ_RX_COUNT_BY_LOWER_MAC = 3, 4264 /* ARP Request count successfully transmitted by the device (u32) */ 4265 QCA_ATTR_NUD_STATS_ARP_REQ_COUNT_TX_SUCCESS = 4, 4266 /* ARP Response count received by lower MAC (u32) */ 4267 QCA_ATTR_NUD_STATS_ARP_RSP_RX_COUNT_BY_LOWER_MAC = 5, 4268 /* ARP Response count received by upper MAC (u32) */ 4269 QCA_ATTR_NUD_STATS_ARP_RSP_RX_COUNT_BY_UPPER_MAC = 6, 4270 /* ARP Response count delivered to netdev (u32) */ 4271 QCA_ATTR_NUD_STATS_ARP_RSP_COUNT_TO_NETDEV = 7, 4272 /* ARP Response count dropped due to out of order reception (u32) */ 4273 QCA_ATTR_NUD_STATS_ARP_RSP_COUNT_OUT_OF_ORDER_DROP = 8, 4274 /* Flag indicating if the station's link to the AP is active. 4275 * Active Link - If included, Inactive link - If not included 4276 */ 4277 QCA_ATTR_NUD_STATS_AP_LINK_ACTIVE = 9, 4278 /* Flag indicating if there is any duplicate address detected (DAD). 4279 * Yes - If detected, No - If not detected. 4280 */ 4281 QCA_ATTR_NUD_STATS_IS_DAD = 10, 4282 /* List of Data packet types for which the stats are requested. 4283 * This list does not carry ARP stats as they are done by the 4284 * above attributes. Represented by enum qca_attr_nud_data_stats. 4285 */ 4286 QCA_ATTR_NUD_STATS_DATA_PKT_STATS = 11, 4287 4288 /* keep last */ 4289 QCA_ATTR_NUD_STATS_GET_LAST, 4290 QCA_ATTR_NUD_STATS_GET_MAX = 4291 QCA_ATTR_NUD_STATS_GET_LAST - 1, 4292 }; 4293 4294 enum qca_wlan_btm_candidate_status { 4295 QCA_STATUS_ACCEPT = 0, 4296 QCA_STATUS_REJECT_EXCESSIVE_FRAME_LOSS_EXPECTED = 1, 4297 QCA_STATUS_REJECT_EXCESSIVE_DELAY_EXPECTED = 2, 4298 QCA_STATUS_REJECT_INSUFFICIENT_QOS_CAPACITY = 3, 4299 QCA_STATUS_REJECT_LOW_RSSI = 4, 4300 QCA_STATUS_REJECT_HIGH_INTERFERENCE = 5, 4301 QCA_STATUS_REJECT_UNKNOWN = 6, 4302 }; 4303 4304 enum qca_wlan_vendor_attr_btm_candidate_info { 4305 QCA_WLAN_VENDOR_ATTR_BTM_CANDIDATE_INFO_INVALID = 0, 4306 4307 /* 6-byte MAC address representing the BSSID of transition candidate */ 4308 QCA_WLAN_VENDOR_ATTR_BTM_CANDIDATE_INFO_BSSID = 1, 4309 /* Unsigned 32-bit value from enum qca_wlan_btm_candidate_status 4310 * returned by the driver. It says whether the BSSID provided in 4311 * QCA_WLAN_VENDOR_ATTR_BTM_CANDIDATE_INFO_BSSID is acceptable by 4312 * the driver, if not it specifies the reason for rejection. 4313 * Note that the user-space can overwrite the transition reject reason 4314 * codes provided by driver based on more information. 4315 */ 4316 QCA_WLAN_VENDOR_ATTR_BTM_CANDIDATE_INFO_STATUS = 2, 4317 4318 /* keep last */ 4319 QCA_WLAN_VENDOR_ATTR_BTM_CANDIDATE_INFO_AFTER_LAST, 4320 QCA_WLAN_VENDOR_ATTR_BTM_CANDIDATE_INFO_MAX = 4321 QCA_WLAN_VENDOR_ATTR_BTM_CANDIDATE_INFO_AFTER_LAST - 1, 4322 }; 4323 4324 enum qca_attr_trace_level { 4325 QCA_ATTR_TRACE_LEVEL_INVALID = 0, 4326 /* 4327 * Nested array of the following attributes: 4328 * QCA_ATTR_TRACE_LEVEL_MODULE, 4329 * QCA_ATTR_TRACE_LEVEL_MASK. 4330 */ 4331 QCA_ATTR_TRACE_LEVEL_PARAM = 1, 4332 /* 4333 * Specific QCA host driver module. Please refer to the QCA host 4334 * driver implementation to get the specific module ID. 4335 */ 4336 QCA_ATTR_TRACE_LEVEL_MODULE = 2, 4337 /* Different trace level masks represented in the QCA host driver. */ 4338 QCA_ATTR_TRACE_LEVEL_MASK = 3, 4339 4340 /* keep last */ 4341 QCA_ATTR_TRACE_LEVEL_AFTER_LAST, 4342 QCA_ATTR_TRACE_LEVEL_MAX = 4343 QCA_ATTR_TRACE_LEVEL_AFTER_LAST - 1, 4344 }; 4345 4346 /** 4347 * enum qca_wlan_vendor_attr_get_he_capabilities - IEEE 802.11ax HE capabilities 4348 */ 4349 enum qca_wlan_vendor_attr_get_he_capabilities { 4350 QCA_WLAN_VENDOR_ATTR_HE_CAPABILITIES_INVALID = 0, 4351 /* Whether HE capabilities is supported 4352 * (u8 attribute: 0 = not supported, 1 = supported) 4353 */ 4354 QCA_WLAN_VENDOR_ATTR_HE_SUPPORTED = 1, 4355 /* HE PHY capabilities, array of 3 u32 values */ 4356 QCA_WLAN_VENDOR_ATTR_PHY_CAPAB = 2, 4357 /* HE MAC capabilities (u32 attribute) */ 4358 QCA_WLAN_VENDOR_ATTR_MAC_CAPAB = 3, 4359 /* HE MCS map (u32 attribute) */ 4360 QCA_WLAN_VENDOR_ATTR_HE_MCS = 4, 4361 /* Number of SS (u32 attribute) */ 4362 QCA_WLAN_VENDOR_ATTR_NUM_SS = 5, 4363 /* RU count (u32 attribute) */ 4364 QCA_WLAN_VENDOR_ATTR_RU_IDX_MASK = 6, 4365 /* PPE threshold data, array of 8 u32 values */ 4366 QCA_WLAN_VENDOR_ATTR_PPE_THRESHOLD = 7, 4367 4368 /* keep last */ 4369 QCA_WLAN_VENDOR_ATTR_HE_CAPABILITIES_AFTER_LAST, 4370 QCA_WLAN_VENDOR_ATTR_HE_CAPABILITIES_MAX = 4371 QCA_WLAN_VENDOR_ATTR_HE_CAPABILITIES_AFTER_LAST - 1, 4372 }; 4373 4374 /** 4375 * enum qca_wlan_vendor_attr_spectral_scan - Spectral scan config parameters 4376 */ 4377 enum qca_wlan_vendor_attr_spectral_scan { 4378 QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_CONFIG_INVALID = 0, 4379 /* Number of times the chip enters spectral scan mode before 4380 * deactivating spectral scans. When set to 0, chip will enter spectral 4381 * scan mode continuously. u32 attribute. 4382 */ 4383 QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_CONFIG_SCAN_COUNT = 1, 4384 /* Spectral scan period. Period increment resolution is 256*Tclk, 4385 * where Tclk = 1/44 MHz (Gmode), 1/40 MHz (Amode). u32 attribute. 4386 */ 4387 QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_CONFIG_SCAN_PERIOD = 2, 4388 /* Spectral scan priority. u32 attribute. */ 4389 QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_CONFIG_PRIORITY = 3, 4390 /* Number of FFT data points to compute. u32 attribute. */ 4391 QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_CONFIG_FFT_SIZE = 4, 4392 /* Enable targeted gain change before starting the spectral scan FFT. 4393 * u32 attribute. 4394 */ 4395 QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_CONFIG_GC_ENA = 5, 4396 /* Restart a queued spectral scan. u32 attribute. */ 4397 QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_CONFIG_RESTART_ENA = 6, 4398 /* Noise floor reference number for the calculation of bin power. 4399 * u32 attribute. 4400 */ 4401 QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_CONFIG_NOISE_FLOOR_REF = 7, 4402 /* Disallow spectral scan triggers after TX/RX packets by setting 4403 * this delay value to roughly SIFS time period or greater. 4404 * u32 attribute. 4405 */ 4406 QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_CONFIG_INIT_DELAY = 8, 4407 /* Number of strong bins (inclusive) per sub-channel, below 4408 * which a signal is declared a narrow band tone. u32 attribute. 4409 */ 4410 QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_CONFIG_NB_TONE_THR = 9, 4411 /* Specify the threshold over which a bin is declared strong (for 4412 * scan bandwidth analysis). u32 attribute. 4413 */ 4414 QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_CONFIG_STR_BIN_THR = 10, 4415 /* Spectral scan report mode. u32 attribute. */ 4416 QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_CONFIG_WB_RPT_MODE = 11, 4417 /* RSSI report mode, if the ADC RSSI is below 4418 * QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_CONFIG_RSSI_THR, 4419 * then FFTs will not trigger, but timestamps and summaries get 4420 * reported. u32 attribute. 4421 */ 4422 QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_CONFIG_RSSI_RPT_MODE = 12, 4423 /* ADC RSSI must be greater than or equal to this threshold (signed dB) 4424 * to ensure spectral scan reporting with normal error code. 4425 * u32 attribute. 4426 */ 4427 QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_CONFIG_RSSI_THR = 13, 4428 /* Format of frequency bin magnitude for spectral scan triggered FFTs: 4429 * 0: linear magnitude, 1: log magnitude (20*log10(lin_mag)). 4430 * u32 attribute. 4431 */ 4432 QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_CONFIG_PWR_FORMAT = 14, 4433 /* Format of FFT report to software for spectral scan triggered FFTs. 4434 * 0: No FFT report (only spectral scan summary report) 4435 * 1: 2-dword summary of metrics for each completed FFT + spectral scan 4436 * report 4437 * 2: 2-dword summary of metrics for each completed FFT + 1x-oversampled 4438 * bins (in-band) per FFT + spectral scan summary report 4439 * 3: 2-dword summary of metrics for each completed FFT + 2x-oversampled 4440 * bins (all) per FFT + spectral scan summary report 4441 * u32 attribute. 4442 */ 4443 QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_CONFIG_RPT_MODE = 15, 4444 /* Number of LSBs to shift out in order to scale the FFT bins. 4445 * u32 attribute. 4446 */ 4447 QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_CONFIG_BIN_SCALE = 16, 4448 /* Set to 1 (with spectral_scan_pwr_format=1), to report bin magnitudes 4449 * in dBm power. u32 attribute. 4450 */ 4451 QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_CONFIG_DBM_ADJ = 17, 4452 /* Per chain enable mask to select input ADC for search FFT. 4453 * u32 attribute. 4454 */ 4455 QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_CONFIG_CHN_MASK = 18, 4456 /* An unsigned 64-bit integer provided by host driver to identify the 4457 * spectral scan request. This attribute is included in the scan 4458 * response message for @QCA_NL80211_VENDOR_SUBCMD_SPECTRAL_SCAN_START 4459 * and used as an attribute in 4460 * @QCA_NL80211_VENDOR_SUBCMD_SPECTRAL_SCAN_STOP to identify the 4461 * specific scan to be stopped. 4462 */ 4463 QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_COOKIE = 19, 4464 /* Skip interval for FFT reports. u32 attribute */ 4465 QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_CONFIG_FFT_PERIOD = 20, 4466 /* Set to report only one set of FFT results. 4467 * u32 attribute. 4468 */ 4469 QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_CONFIG_SHORT_REPORT = 21, 4470 /* Debug level for spectral module in driver. 4471 * 0 : Verbosity level 0 4472 * 1 : Verbosity level 1 4473 * 2 : Verbosity level 2 4474 * 3 : Matched filterID display 4475 * 4 : One time dump of FFT report 4476 * u32 attribute. 4477 */ 4478 QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_CONFIG_DEBUG_LEVEL = 22, 4479 /* Type of spectral scan request. u32 attribute. 4480 * It uses values defined in enum 4481 * qca_wlan_vendor_attr_spectral_scan_request_type. 4482 */ 4483 QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_REQUEST_TYPE = 23, 4484 4485 QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_CONFIG_AFTER_LAST, 4486 QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_CONFIG_MAX = 4487 QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_CONFIG_AFTER_LAST - 1, 4488 }; 4489 4490 /** 4491 * enum qca_wlan_vendor_attr_spectral_diag_stats - Used by the vendor command 4492 * QCA_NL80211_VENDOR_SUBCMD_SPECTRAL_SCAN_GET_DIAG_STATS. 4493 */ 4494 enum qca_wlan_vendor_attr_spectral_diag_stats { 4495 QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_DIAG_INVALID = 0, 4496 /* Number of spectral TLV signature mismatches. 4497 * u64 attribute. 4498 */ 4499 QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_DIAG_SIG_MISMATCH = 1, 4500 /* Number of spectral phyerror events with insufficient length when 4501 * parsing for secondary 80 search FFT report. u64 attribute. 4502 */ 4503 QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_DIAG_SEC80_SFFT_INSUFFLEN = 2, 4504 /* Number of spectral phyerror events without secondary 80 4505 * search FFT report. u64 attribute. 4506 */ 4507 QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_DIAG_NOSEC80_SFFT = 3, 4508 /* Number of spectral phyerror events with vht operation segment 1 id 4509 * mismatches in search fft report. u64 attribute. 4510 */ 4511 QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_DIAG_VHTSEG1ID_MISMATCH = 4, 4512 /* Number of spectral phyerror events with vht operation segment 2 id 4513 * mismatches in search fft report. u64 attribute. 4514 */ 4515 QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_DIAG_VHTSEG2ID_MISMATCH = 5, 4516 4517 QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_DIAG_AFTER_LAST, 4518 QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_DIAG_MAX = 4519 QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_DIAG_AFTER_LAST - 1, 4520 }; 4521 4522 /** 4523 * enum qca_wlan_vendor_attr_spectral_cap - Used by the vendor command 4524 * QCA_NL80211_VENDOR_SUBCMD_SPECTRAL_SCAN_GET_CAP_INFO. 4525 */ 4526 enum qca_wlan_vendor_attr_spectral_cap { 4527 QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_CAP_INVALID = 0, 4528 /* Flag attribute to indicate phydiag capability */ 4529 QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_CAP_PHYDIAG = 1, 4530 /* Flag attribute to indicate radar detection capability */ 4531 QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_CAP_RADAR = 2, 4532 /* Flag attribute to indicate spectral capability */ 4533 QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_CAP_SPECTRAL = 3, 4534 /* Flag attribute to indicate advanced spectral capability */ 4535 QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_CAP_ADVANCED_SPECTRAL = 4, 4536 /* Spectral hardware generation. u32 attribute. 4537 * It uses values defined in enum 4538 * qca_wlan_vendor_spectral_scan_cap_hw_gen. 4539 */ 4540 QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_CAP_HW_GEN = 5, 4541 /* Spectral bin scaling formula ID. u16 attribute. 4542 * It uses values defined in enum 4543 * qca_wlan_vendor_spectral_scan_cap_formula_id. 4544 */ 4545 QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_CAP_FORMULA_ID = 6, 4546 /* Spectral bin scaling param - low level offset. 4547 * s16 attribute. 4548 */ 4549 QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_CAP_LOW_LEVEL_OFFSET = 7, 4550 /* Spectral bin scaling param - high level offset. 4551 * s16 attribute. 4552 */ 4553 QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_CAP_HIGH_LEVEL_OFFSET = 8, 4554 /* Spectral bin scaling param - RSSI threshold. 4555 * s16 attribute. 4556 */ 4557 QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_CAP_RSSI_THR = 9, 4558 /* Spectral bin scaling param - default AGC max gain. 4559 * u8 attribute. 4560 */ 4561 QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_CAP_DEFAULT_AGC_MAX_GAIN = 10, 4562 4563 QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_CAP_AFTER_LAST, 4564 QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_CAP_MAX = 4565 QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_CAP_AFTER_LAST - 1, 4566 }; 4567 4568 /** 4569 * enum qca_wlan_vendor_attr_spectral_scan_status - used by the vendor command 4570 * QCA_NL80211_VENDOR_SUBCMD_SPECTRAL_SCAN_GET_STATUS. 4571 */ 4572 enum qca_wlan_vendor_attr_spectral_scan_status { 4573 QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_STATUS_INVALID = 0, 4574 /* Flag attribute to indicate whether spectral scan is enabled */ 4575 QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_STATUS_IS_ENABLED = 1, 4576 /* Flag attribute to indicate whether spectral scan is in progress*/ 4577 QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_STATUS_IS_ACTIVE = 2, 4578 4579 QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_STATUS_AFTER_LAST, 4580 QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_STATUS_MAX = 4581 QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_STATUS_AFTER_LAST - 1, 4582 }; 4583 4584 /** 4585 * qca_wlan_vendor_attr_spectral_scan_request_type: Attribute values for 4586 * QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_REQUEST_TYPE to the vendor subcmd 4587 * QCA_NL80211_VENDOR_SUBCMD_SPECTRAL_SCAN_START. This represents the 4588 * spectral scan request types. 4589 * @QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_REQUEST_TYPE_SCAN_AND_CONFIG: Request to 4590 * set the spectral parameters and start scan. 4591 * @QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_REQUEST_TYPE_SCAN: Request to 4592 * only set the spectral parameters. 4593 * @QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_REQUEST_TYPE_CONFIG: Request to 4594 * only start the spectral scan. 4595 */ 4596 enum qca_wlan_vendor_attr_spectral_scan_request_type { 4597 QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_REQUEST_TYPE_SCAN_AND_CONFIG, 4598 QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_REQUEST_TYPE_SCAN, 4599 QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_REQUEST_TYPE_CONFIG, 4600 }; 4601 4602 /** 4603 * qca_wlan_vendor_spectral_scan_cap_hw_gen: Attribute values for 4604 * QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_CAP_HW_GEN to the vendor subcmd 4605 * QCA_NL80211_VENDOR_SUBCMD_SPECTRAL_SCAN_GET_CAP_INFO. This represents the 4606 * spectral hardware generation. 4607 * @QCA_WLAN_VENDOR_SPECTRAL_SCAN_CAP_HW_GEN_1: generation 1 4608 * @QCA_WLAN_VENDOR_SPECTRAL_SCAN_CAP_HW_GEN_2: generation 2 4609 * @QCA_WLAN_VENDOR_SPECTRAL_SCAN_CAP_HW_GEN_3: generation 3 4610 */ 4611 enum qca_wlan_vendor_spectral_scan_cap_hw_gen { 4612 QCA_WLAN_VENDOR_SPECTRAL_SCAN_CAP_HW_GEN_1 = 0, 4613 QCA_WLAN_VENDOR_SPECTRAL_SCAN_CAP_HW_GEN_2 = 1, 4614 QCA_WLAN_VENDOR_SPECTRAL_SCAN_CAP_HW_GEN_3 = 2, 4615 }; 4616 4617 enum qca_wlan_vendor_tos { 4618 QCA_WLAN_VENDOR_TOS_BK = 0, 4619 QCA_WLAN_VENDOR_TOS_BE = 1, 4620 QCA_WLAN_VENDOR_TOS_VI = 2, 4621 QCA_WLAN_VENDOR_TOS_VO = 3, 4622 }; 4623 4624 /** 4625 * enum qca_wlan_vendor_attr_active_tos - Used by the vendor command 4626 * QCA_NL80211_VENDOR_SUBCMD_ACTIVE_TOS. 4627 */ 4628 enum qca_wlan_vendor_attr_active_tos { 4629 QCA_WLAN_VENDOR_ATTR_ACTIVE_TOS_INVALID = 0, 4630 /* Type Of Service - Represented by qca_wlan_vendor_tos */ 4631 QCA_WLAN_VENDOR_ATTR_ACTIVE_TOS = 1, 4632 /* Flag attribute representing the start (attribute included) or stop 4633 * (attribute not included) of the respective TOS. 4634 */ 4635 QCA_WLAN_VENDOR_ATTR_ACTIVE_TOS_START = 2, 4636 }; 4637 4638 enum qca_wlan_vendor_hang_reason { 4639 /* Unspecified reason */ 4640 QCA_WLAN_HANG_REASON_UNSPECIFIED = 0, 4641 /* No Map for the MAC entry for the received frame */ 4642 QCA_WLAN_HANG_RX_HASH_NO_ENTRY_FOUND = 1, 4643 /* Peer deletion timeout happened */ 4644 QCA_WLAN_HANG_PEER_DELETION_TIMEDOUT = 2, 4645 /* Peer unmap timeout */ 4646 QCA_WLAN_HANG_PEER_UNMAP_TIMEDOUT = 3, 4647 /* Scan request timed out */ 4648 QCA_WLAN_HANG_SCAN_REQ_EXPIRED = 4, 4649 /* Consecutive Scan attempt failures */ 4650 QCA_WLAN_HANG_SCAN_ATTEMPT_FAILURES = 5, 4651 /* Unable to get the message buffer */ 4652 QCA_WLAN_HANG_GET_MSG_BUFF_FAILURE = 6, 4653 /* Current command processing is timedout */ 4654 QCA_WLAN_HANG_ACTIVE_LIST_TIMEOUT = 7, 4655 /* Timeout for an ACK from FW for suspend request */ 4656 QCA_WLAN_HANG_SUSPEND_TIMEOUT = 8, 4657 /* Timeout for an ACK from FW for resume request */ 4658 QCA_WLAN_HANG_RESUME_TIMEOUT = 9, 4659 /* Transmission timeout for consecutive data frames */ 4660 QCA_WLAN_HANG_TRANSMISSIONS_TIMEOUT = 10, 4661 /* Timeout for the TX completion status of data frame */ 4662 QCA_WLAN_HANG_TX_COMPLETE_TIMEOUT = 11, 4663 /* DXE failure for TX/RX, DXE resource unavailability */ 4664 QCA_WLAN_HANG_DXE_FAILURE = 12, 4665 /* WMI pending commands exceed the maximum count */ 4666 QCA_WLAN_HANG_WMI_EXCEED_MAX_PENDING_CMDS = 13, 4667 }; 4668 4669 /** 4670 * enum qca_wlan_vendor_attr_hang - Used by the vendor command 4671 * QCA_NL80211_VENDOR_SUBCMD_HANG. 4672 */ 4673 enum qca_wlan_vendor_attr_hang { 4674 QCA_WLAN_VENDOR_ATTR_HANG_INVALID = 0, 4675 /* Reason for the hang - u32 attribute with a value from enum 4676 * qca_wlan_vendor_hang_reason. 4677 */ 4678 QCA_WLAN_VENDOR_ATTR_HANG_REASON = 1, 4679 4680 QCA_WLAN_VENDOR_ATTR_HANG_AFTER_LAST, 4681 QCA_WLAN_VENDOR_ATTR_HANG_MAX = 4682 QCA_WLAN_VENDOR_ATTR_HANG_AFTER_LAST - 1, 4683 }; 4684 4685 /** 4686 * enum qca_wlan_vendor_attr_flush_pending - Attributes for 4687 * flushing pending traffic in firmware. 4688 * 4689 * @QCA_WLAN_VENDOR_ATTR_PEER_ADDR: Configure peer MAC address. 4690 * @QCA_WLAN_VENDOR_ATTR_AC: Configure access category of the pending 4691 * packets. It is u8 value with bit 0~3 represent AC_BE, AC_BK, 4692 * AC_VI, AC_VO respectively. Set the corresponding bit to 1 to 4693 * flush packets with access category. 4694 */ 4695 enum qca_wlan_vendor_attr_flush_pending { 4696 QCA_WLAN_VENDOR_ATTR_FLUSH_PENDING_INVALID = 0, 4697 QCA_WLAN_VENDOR_ATTR_PEER_ADDR = 1, 4698 QCA_WLAN_VENDOR_ATTR_AC = 2, 4699 4700 /* keep last */ 4701 QCA_WLAN_VENDOR_ATTR_FLUSH_PENDING_AFTER_LAST, 4702 QCA_WLAN_VENDOR_ATTR_FLUSH_PENDING_MAX = 4703 QCA_WLAN_VENDOR_ATTR_FLUSH_PENDING_AFTER_LAST - 1, 4704 }; 4705 4706 /** 4707 * qca_wlan_vendor_spectral_scan_cap_formula_id: Attribute values for 4708 * QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_CAP_FORMULA_ID in the vendor subcmd 4709 * QCA_NL80211_VENDOR_SUBCMD_SPECTRAL_SCAN_GET_CAP_INFO. This represents the 4710 * Spectral bin scaling formula ID. 4711 * @QCA_WLAN_VENDOR_SPECTRAL_SCAN_CAP_NO_SCALING: No scaling 4712 * @QCA_WLAN_VENDOR_SPECTRAL_SCAN_CAP_AGC_GAIN_RSSI_CORR_BASED: AGC gain 4713 * and RSSI threshold based formula. 4714 */ 4715 enum qca_wlan_vendor_spectral_scan_cap_formula_id { 4716 QCA_WLAN_VENDOR_SPECTRAL_SCAN_CAP_NO_SCALING = 0, 4717 QCA_WLAN_VENDOR_SPECTRAL_SCAN_CAP_AGC_GAIN_RSSI_CORR_BASED = 1, 4718 }; 4719 4720 /** 4721 * enum qca_wlan_vendor_attr_rropavail_info - Specifies whether Representative 4722 * RF Operating Parameter (RROP) information is available, and if so, at which 4723 * point in the application-driver interaction sequence it can be retrieved by 4724 * the application from the driver. This point may vary by architecture and 4725 * other factors. This is a u16 value. 4726 */ 4727 enum qca_wlan_vendor_attr_rropavail_info { 4728 /* RROP information is unavailable. */ 4729 QCA_WLAN_VENDOR_ATTR_RROPAVAIL_INFO_UNAVAILABLE, 4730 /* RROP information is available and the application can retrieve the 4731 * information after receiving an QCA_NL80211_VENDOR_SUBCMD_EXTERNAL_ACS 4732 * event from the driver. 4733 */ 4734 QCA_WLAN_VENDOR_ATTR_RROPAVAIL_INFO_EXTERNAL_ACS_START, 4735 /* RROP information is available only after a vendor specific scan 4736 * (requested using QCA_NL80211_VENDOR_SUBCMD_TRIGGER_SCAN) has 4737 * successfully completed. The application can retrieve the information 4738 * after receiving the QCA_NL80211_VENDOR_SUBCMD_SCAN_DONE event from 4739 * the driver. 4740 */ 4741 QCA_WLAN_VENDOR_ATTR_RROPAVAIL_INFO_VSCAN_END, 4742 }; 4743 4744 /** 4745 * enum qca_wlan_vendor_attr_rrop_info - Specifies vendor specific 4746 * Representative RF Operating Parameter (RROP) information. It is sent for the 4747 * vendor command QCA_NL80211_VENDOR_SUBCMD_GET_RROP_INFO. This information is 4748 * intended for use by external Auto Channel Selection applications. It provides 4749 * guidance values for some RF parameters that are used by the system during 4750 * operation. These values could vary by channel, band, radio, and so on. 4751 */ 4752 enum qca_wlan_vendor_attr_rrop_info { 4753 QCA_WLAN_VENDOR_ATTR_RROP_INFO_INVALID = 0, 4754 4755 /* Representative Tx Power List (RTPL) which has an array of nested 4756 * values as per attributes in enum qca_wlan_vendor_attr_rtplinst. 4757 */ 4758 QCA_WLAN_VENDOR_ATTR_RROP_INFO_RTPL = 1, 4759 4760 QCA_WLAN_VENDOR_ATTR_RROP_INFO_AFTER_LAST, 4761 QCA_WLAN_VENDOR_ATTR_RROP_INFO_MAX = 4762 QCA_WLAN_VENDOR_ATTR_RROP_INFO_AFTER_LAST - 1 4763 }; 4764 4765 /** 4766 * enum qca_wlan_vendor_attr_rtplinst - Specifies attributes for individual list 4767 * entry instances in the Representative Tx Power List (RTPL). It provides 4768 * simplified power values intended for helping external Auto channel Selection 4769 * applications compare potential Tx power performance between channels, other 4770 * operating conditions remaining identical. These values are not necessarily 4771 * the actual Tx power values that will be used by the system. They are also not 4772 * necessarily the max or average values that will be used. Instead, they are 4773 * relative, summarized keys for algorithmic use computed by the driver or 4774 * underlying firmware considering a number of vendor specific factors. 4775 */ 4776 enum qca_wlan_vendor_attr_rtplinst { 4777 QCA_WLAN_VENDOR_ATTR_RTPLINST_INVALID = 0, 4778 4779 /* Primary channel number (u8) */ 4780 QCA_WLAN_VENDOR_ATTR_RTPLINST_PRIMARY = 1, 4781 /* Representative Tx power in dBm (s32) with emphasis on throughput. */ 4782 QCA_WLAN_VENDOR_ATTR_RTPLINST_TXPOWER_THROUGHPUT = 2, 4783 /* Representative Tx power in dBm (s32) with emphasis on range. */ 4784 QCA_WLAN_VENDOR_ATTR_RTPLINST_TXPOWER_RANGE = 3, 4785 4786 QCA_WLAN_VENDOR_ATTR_RTPLINST_AFTER_LAST, 4787 QCA_WLAN_VENDOR_ATTR_RTPLINST_MAX = 4788 QCA_WLAN_VENDOR_ATTR_RTPLINST_AFTER_LAST - 1, 4789 }; 4790 4791 /** 4792 * enum qca_wlan_vendor_attr_config_latency_level - Level for 4793 * wlan latency module. 4794 * 4795 * There will be various of Wi-Fi functionality like scan/roaming/adaptive 4796 * power saving which would causing data exchange out of service, this 4797 * would be a big impact on latency. For latency sensitive applications over 4798 * Wi-Fi are intolerant to such operations and thus would configure them 4799 * to meet their respective needs. It is well understood by such applications 4800 * that altering the default behavior would degrade the Wi-Fi functionality 4801 * w.r.t the above pointed WLAN operations. 4802 * 4803 * @QCA_WLAN_VENDOR_ATTR_CONFIG_LATENCY_LEVEL_NORMAL: 4804 * Default WLAN operation level which throughput orientated. 4805 * @QCA_WLAN_VENDOR_ATTR_CONFIG_LATENCY_LEVEL_MODERATE: 4806 * Use moderate level to improve latency by limit scan duration. 4807 * @QCA_WLAN_VENDOR_ATTR_CONFIG_LATENCY_LEVEL_LOW: 4808 * Use low latency level to benifit application like concurrent 4809 * downloading or video streaming via constraint scan/adaptive PS. 4810 * @QCA_WLAN_VENDOR_ATTR_CONFIG_LATENCY_LEVEL_ULTRALOW: 4811 * Use ultra low latency level to benefit for gaming/voice 4812 * application via constraint scan/roaming/adaptive PS. 4813 */ 4814 enum qca_wlan_vendor_attr_config_latency_level { 4815 QCA_WLAN_VENDOR_ATTR_CONFIG_LATENCY_LEVEL_INVALID = 0, 4816 QCA_WLAN_VENDOR_ATTR_CONFIG_LATENCY_LEVEL_NORMAL = 1, 4817 QCA_WLAN_VENDOR_ATTR_CONFIG_LATENCY_LEVEL_MODERATE = 2, 4818 QCA_WLAN_VENDOR_ATTR_CONFIG_LATENCY_LEVEL_LOW = 3, 4819 QCA_WLAN_VENDOR_ATTR_CONFIG_LATENCY_LEVEL_ULTRALOW = 4, 4820 4821 /* keep last */ 4822 QCA_WLAN_VENDOR_ATTR_CONFIG_LATENCY_LEVEL_AFTER_LAST, 4823 QCA_WLAN_VENDOR_ATTR_CONFIG_LATENCY_LEVEL_MAX = 4824 QCA_WLAN_VENDOR_ATTR_CONFIG_LATENCY_LEVEL_AFTER_LAST - 1, 4825 }; 4826 4827 /** 4828 * enum qca_wlan_vendor_attr_wlan_mac - Used by the vendor command 4829 * QCA_NL80211_VENDOR_SUBCMD_WLAN_MAC_INFO. 4830 */ 4831 enum qca_wlan_vendor_attr_mac { 4832 QCA_WLAN_VENDOR_ATTR_MAC_INVALID = 0, 4833 4834 /* MAC mode info list which has an array of nested values as 4835 * per attributes in enum qca_wlan_vendor_attr_mac_mode_info. 4836 */ 4837 QCA_WLAN_VENDOR_ATTR_MAC_INFO = 1, 4838 4839 /* keep last */ 4840 QCA_WLAN_VENDOR_ATTR_MAC_AFTER_LAST, 4841 QCA_WLAN_VENDOR_ATTR_MAC_MAX = 4842 QCA_WLAN_VENDOR_ATTR_MAC_AFTER_LAST - 1, 4843 }; 4844 4845 /** 4846 * enum qca_wlan_vendor_attr_mac_iface_info - Information of the connected 4847 * Wi-Fi netdev interface on a respective MAC. 4848 * Used by the attribute QCA_WLAN_VENDOR_ATTR_MAC_IFACE_INFO. 4849 */ 4850 enum qca_wlan_vendor_attr_mac_iface_info { 4851 QCA_WLAN_VENDOR_ATTR_MAC_IFACE_INFO_INVALID = 0, 4852 /* Wi-Fi netdev's interface index (u32) */ 4853 QCA_WLAN_VENDOR_ATTR_MAC_IFACE_INFO_IFINDEX = 1, 4854 /* Associated frequency in MHz of the connected Wi-Fi interface (u32) */ 4855 QCA_WLAN_VENDOR_ATTR_MAC_IFACE_INFO_FREQ = 2, 4856 4857 /* keep last */ 4858 QCA_WLAN_VENDOR_ATTR_MAC_IFACE_INFO_AFTER_LAST, 4859 QCA_WLAN_VENDOR_ATTR_MAC_IFACE_INFO_MAX = 4860 QCA_WLAN_VENDOR_ATTR_MAC_IFACE_INFO_AFTER_LAST - 1, 4861 }; 4862 4863 /** 4864 * enum qca_wlan_vendor_attr_mac_info - Points to MAC the information. 4865 * Used by the attribute QCA_WLAN_VENDOR_ATTR_MAC_INFO of the 4866 * vendor command QCA_NL80211_VENDOR_SUBCMD_WLAN_MAC_INFO. 4867 */ 4868 enum qca_wlan_vendor_attr_mac_info { 4869 QCA_WLAN_VENDOR_ATTR_MAC_INFO_INVALID = 0, 4870 /* Hardware MAC ID associated for the MAC (u32) */ 4871 QCA_WLAN_VENDOR_ATTR_MAC_INFO_MAC_ID = 1, 4872 /* Band supported by the MAC at a given point. 4873 * This is a u32 bitmask of BIT(NL80211_BAND_*) as described in %enum 4874 * nl80211_band. 4875 */ 4876 QCA_WLAN_VENDOR_ATTR_MAC_INFO_BAND = 2, 4877 /* Refers to list of WLAN netdev interfaces associated with this MAC. 4878 * Represented by enum qca_wlan_vendor_attr_mac_iface_info. 4879 */ 4880 QCA_WLAN_VENDOR_ATTR_MAC_IFACE_INFO = 3, 4881 4882 /* keep last */ 4883 QCA_WLAN_VENDOR_ATTR_MAC_INFO_AFTER_LAST, 4884 QCA_WLAN_VENDOR_ATTR_MAC_INFO_MAX = 4885 QCA_WLAN_VENDOR_ATTR_MAC_INFO_AFTER_LAST - 1, 4886 }; 4887 4888 /** 4889 * enum qca_wlan_vendor_attr_get_logger_features - Used by the vendor command 4890 * QCA_NL80211_VENDOR_SUBCMD_GET_LOGGER_FEATURE_SET. 4891 */ 4892 enum qca_wlan_vendor_attr_get_logger_features { 4893 QCA_WLAN_VENDOR_ATTR_LOGGER_INVALID = 0, 4894 /* Unsigned 32-bit enum value of wifi_logger_supported_features */ 4895 QCA_WLAN_VENDOR_ATTR_LOGGER_SUPPORTED = 1, 4896 /* keep last */ 4897 QCA_WLAN_VENDOR_ATTR_LOGGER_AFTER_LAST, 4898 QCA_WLAN_VENDOR_ATTR_LOGGER_MAX = 4899 QCA_WLAN_VENDOR_ATTR_LOGGER_AFTER_LAST - 1, 4900 }; 4901 4902 /** 4903 * enum wifi_logger_supported_features - Values for supported logger features 4904 */ 4905 enum wifi_logger_supported_features { 4906 WIFI_LOGGER_MEMORY_DUMP_FEATURE = (1 << (0)), 4907 WIFI_LOGGER_PER_PACKET_TX_RX_STATUS_FEATURE = (1 << (1)), 4908 WIFI_LOGGER_CONNECT_EVENT_FEATURE = (1 << (2)), 4909 WIFI_LOGGER_POWER_EVENT_FEATURE = (1 << (3)), 4910 WIFI_LOGGER_WAKE_LOCK_FEATURE = (1 << (4)), 4911 WIFI_LOGGER_VERBOSE_FEATURE = (1 << (5)), 4912 WIFI_LOGGER_WATCHDOG_TIMER_FEATURE = (1 << (6)), 4913 WIFI_LOGGER_DRIVER_DUMP_FEATURE = (1 << (7)), 4914 WIFI_LOGGER_PACKET_FATE_FEATURE = (1 << (8)), 4915 }; 4916 4917 /** 4918 * enum qca_wlan_tdls_caps_features_supported - Values for TDLS get 4919 * capabilities features 4920 */ 4921 enum qca_wlan_tdls_caps_features_supported { 4922 WIFI_TDLS_SUPPORT = (1 << (0)), 4923 WIFI_TDLS_EXTERNAL_CONTROL_SUPPORT = (1 << (1)), 4924 WIFI_TDLS_OFFCHANNEL_SUPPORT = (1 << (2)) 4925 }; 4926 4927 /** 4928 * enum qca_wlan_vendor_attr_tdls_get_capabilities - Used by the vendor command 4929 * QCA_NL80211_VENDOR_SUBCMD_TDLS_GET_CAPABILITIES. 4930 */ 4931 enum qca_wlan_vendor_attr_tdls_get_capabilities { 4932 QCA_WLAN_VENDOR_ATTR_TDLS_GET_CAPS_INVALID = 0, 4933 /* Indicates the max concurrent sessions */ 4934 /* Unsigned 32-bit value */ 4935 QCA_WLAN_VENDOR_ATTR_TDLS_GET_CAPS_MAX_CONC_SESSIONS, 4936 /* Indicates the support for features */ 4937 /* Unsigned 32-bit bitmap qca_wlan_tdls_caps_features_supported 4938 */ 4939 QCA_WLAN_VENDOR_ATTR_TDLS_GET_CAPS_FEATURES_SUPPORTED, 4940 4941 /* keep last */ 4942 QCA_WLAN_VENDOR_ATTR_TDLS_GET_CAPS_AFTER_LAST, 4943 QCA_WLAN_VENDOR_ATTR_TDLS_GET_CAPS_MAX = 4944 QCA_WLAN_VENDOR_ATTR_TDLS_GET_CAPS_AFTER_LAST - 1, 4945 }; 4946 4947 /** 4948 * enum qca_wlan_offloaded_packets_sending_control - Offload packets control 4949 * command used as value for the attribute 4950 * QCA_WLAN_VENDOR_ATTR_OFFLOADED_PACKETS_SENDING_CONTROL. 4951 */ 4952 enum qca_wlan_offloaded_packets_sending_control { 4953 QCA_WLAN_OFFLOADED_PACKETS_SENDING_CONTROL_INVALID = 0, 4954 QCA_WLAN_OFFLOADED_PACKETS_SENDING_START, 4955 QCA_WLAN_OFFLOADED_PACKETS_SENDING_STOP 4956 }; 4957 4958 /** 4959 * enum qca_wlan_vendor_attr_offloaded_packets - Used by the vendor command 4960 * QCA_NL80211_VENDOR_SUBCMD_OFFLOADED_PACKETS. 4961 */ 4962 enum qca_wlan_vendor_attr_offloaded_packets { 4963 QCA_WLAN_VENDOR_ATTR_OFFLOADED_PACKETS_INVALID = 0, 4964 /* Takes valid value from the enum 4965 * qca_wlan_offloaded_packets_sending_control 4966 * Unsigned 32-bit value 4967 */ 4968 QCA_WLAN_VENDOR_ATTR_OFFLOADED_PACKETS_SENDING_CONTROL, 4969 /* Unsigned 32-bit value */ 4970 QCA_WLAN_VENDOR_ATTR_OFFLOADED_PACKETS_REQUEST_ID, 4971 /* array of u8 len: Max packet size */ 4972 QCA_WLAN_VENDOR_ATTR_OFFLOADED_PACKETS_IP_PACKET_DATA, 4973 /* 6-byte MAC address used to represent source MAC address */ 4974 QCA_WLAN_VENDOR_ATTR_OFFLOADED_PACKETS_SRC_MAC_ADDR, 4975 /* 6-byte MAC address used to represent destination MAC address */ 4976 QCA_WLAN_VENDOR_ATTR_OFFLOADED_PACKETS_DST_MAC_ADDR, 4977 /* Unsigned 32-bit value, in milli seconds */ 4978 QCA_WLAN_VENDOR_ATTR_OFFLOADED_PACKETS_PERIOD, 4979 /* This optional unsigned 16-bit attribute is used for specifying 4980 * ethernet protocol type. If not specified ethertype defaults to IPv4. 4981 */ 4982 QCA_WLAN_VENDOR_ATTR_OFFLOADED_PACKETS_ETHER_PROTO_TYPE, 4983 4984 /* keep last */ 4985 QCA_WLAN_VENDOR_ATTR_OFFLOADED_PACKETS_AFTER_LAST, 4986 QCA_WLAN_VENDOR_ATTR_OFFLOADED_PACKETS_MAX = 4987 QCA_WLAN_VENDOR_ATTR_OFFLOADED_PACKETS_AFTER_LAST - 1, 4988 }; 4989 4990 /** 4991 * enum qca_wlan_rssi_monitoring_control - RSSI control commands used as values 4992 * by the attribute QCA_WLAN_VENDOR_ATTR_RSSI_MONITORING_CONTROL. 4993 */ 4994 enum qca_wlan_rssi_monitoring_control { 4995 QCA_WLAN_RSSI_MONITORING_CONTROL_INVALID = 0, 4996 QCA_WLAN_RSSI_MONITORING_START, 4997 QCA_WLAN_RSSI_MONITORING_STOP, 4998 }; 4999 5000 /** 5001 * enum qca_wlan_vendor_attr_rssi_monitoring - Used by the vendor command 5002 * QCA_NL80211_VENDOR_SUBCMD_MONITOR_RSSI. 5003 */ 5004 enum qca_wlan_vendor_attr_rssi_monitoring { 5005 QCA_WLAN_VENDOR_ATTR_RSSI_MONITORING_INVALID = 0, 5006 /* Takes valid value from the enum 5007 * qca_wlan_rssi_monitoring_control 5008 * Unsigned 32-bit value enum qca_wlan_rssi_monitoring_control 5009 */ 5010 QCA_WLAN_VENDOR_ATTR_RSSI_MONITORING_CONTROL, 5011 /* Unsigned 32-bit value */ 5012 QCA_WLAN_VENDOR_ATTR_RSSI_MONITORING_REQUEST_ID, 5013 /* Signed 8-bit value in dBm */ 5014 QCA_WLAN_VENDOR_ATTR_RSSI_MONITORING_MAX_RSSI, 5015 /* Signed 8-bit value in dBm */ 5016 QCA_WLAN_VENDOR_ATTR_RSSI_MONITORING_MIN_RSSI, 5017 /* attributes to be used/received in callback */ 5018 /* 6-byte MAC address used to represent current BSSID MAC address */ 5019 QCA_WLAN_VENDOR_ATTR_RSSI_MONITORING_CUR_BSSID, 5020 /* Signed 8-bit value indicating the current RSSI */ 5021 QCA_WLAN_VENDOR_ATTR_RSSI_MONITORING_CUR_RSSI, 5022 /* keep last */ 5023 QCA_WLAN_VENDOR_ATTR_RSSI_MONITORING_AFTER_LAST, 5024 QCA_WLAN_VENDOR_ATTR_RSSI_MONITORING_MAX = 5025 QCA_WLAN_VENDOR_ATTR_RSSI_MONITORING_AFTER_LAST - 1, 5026 }; 5027 5028 /** 5029 * enum qca_wlan_vendor_attr_ndp_params - Used by the vendor command 5030 * QCA_NL80211_VENDOR_SUBCMD_NDP. 5031 */ 5032 enum qca_wlan_vendor_attr_ndp_params { 5033 QCA_WLAN_VENDOR_ATTR_NDP_PARAM_INVALID = 0, 5034 /* Unsigned 32-bit value 5035 * enum of sub commands values in qca_wlan_ndp_sub_cmd 5036 */ 5037 QCA_WLAN_VENDOR_ATTR_NDP_SUBCMD, 5038 /* Unsigned 16-bit value */ 5039 QCA_WLAN_VENDOR_ATTR_NDP_TRANSACTION_ID, 5040 /* NL attributes for data used NDP SUB cmds */ 5041 /* Unsigned 32-bit value indicating a service info */ 5042 QCA_WLAN_VENDOR_ATTR_NDP_SERVICE_INSTANCE_ID, 5043 /* Unsigned 32-bit value; channel frequency in MHz */ 5044 QCA_WLAN_VENDOR_ATTR_NDP_CHANNEL, 5045 /* Interface Discovery MAC address. An array of 6 Unsigned int8 */ 5046 QCA_WLAN_VENDOR_ATTR_NDP_PEER_DISCOVERY_MAC_ADDR, 5047 /* Interface name on which NDP is being created */ 5048 QCA_WLAN_VENDOR_ATTR_NDP_IFACE_STR, 5049 /* Unsigned 32-bit value for security */ 5050 /* CONFIG_SECURITY is deprecated, use NCS_SK_TYPE/PMK/SCID instead */ 5051 QCA_WLAN_VENDOR_ATTR_NDP_CONFIG_SECURITY, 5052 /* Unsigned 32-bit value for QoS */ 5053 QCA_WLAN_VENDOR_ATTR_NDP_CONFIG_QOS, 5054 /* Array of u8: len = QCA_WLAN_VENDOR_ATTR_NAN_DP_APP_INFO_LEN */ 5055 QCA_WLAN_VENDOR_ATTR_NDP_APP_INFO, 5056 /* Unsigned 32-bit value for NDP instance Id */ 5057 QCA_WLAN_VENDOR_ATTR_NDP_INSTANCE_ID, 5058 /* Array of instance Ids */ 5059 QCA_WLAN_VENDOR_ATTR_NDP_INSTANCE_ID_ARRAY, 5060 /* Unsigned 32-bit value for initiator/responder NDP response code 5061 * accept/reject 5062 */ 5063 QCA_WLAN_VENDOR_ATTR_NDP_RESPONSE_CODE, 5064 /* NDI MAC address. An array of 6 Unsigned int8 */ 5065 QCA_WLAN_VENDOR_ATTR_NDP_NDI_MAC_ADDR, 5066 /* Unsigned 32-bit value errors types returned by driver 5067 * The wifi_nan.h in AOSP project platform/hardware/libhardware_legacy 5068 * NanStatusType includes these values. 5069 */ 5070 QCA_WLAN_VENDOR_ATTR_NDP_DRV_RESPONSE_STATUS_TYPE, 5071 /* Unsigned 32-bit value error values returned by driver 5072 * The nan_i.h in AOSP project platform/hardware/qcom/wlan 5073 * NanInternalStatusType includes these values. 5074 */ 5075 QCA_WLAN_VENDOR_ATTR_NDP_DRV_RETURN_VALUE, 5076 /* Unsigned 32-bit value for Channel setup configuration 5077 * The wifi_nan.h in AOSP project platform/hardware/libhardware_legacy 5078 * NanDataPathChannelCfg includes these values. 5079 */ 5080 QCA_WLAN_VENDOR_ATTR_NDP_CHANNEL_CONFIG, 5081 /* Unsigned 32-bit value for Cipher Suite Shared Key Type */ 5082 QCA_WLAN_VENDOR_ATTR_NDP_CSID, 5083 /* Array of u8: len = NAN_PMK_INFO_LEN 32 bytes */ 5084 QCA_WLAN_VENDOR_ATTR_NDP_PMK, 5085 /* Security Context Identifier that contains the PMKID 5086 * Array of u8: len = NAN_SCID_BUF_LEN 1024 bytes 5087 */ 5088 QCA_WLAN_VENDOR_ATTR_NDP_SCID, 5089 /* Array of u8: len = NAN_SECURITY_MAX_PASSPHRASE_LEN 63 bytes */ 5090 QCA_WLAN_VENDOR_ATTR_NDP_PASSPHRASE, 5091 /* Array of u8: len = NAN_MAX_SERVICE_NAME_LEN 255 bytes */ 5092 QCA_WLAN_VENDOR_ATTR_NDP_SERVICE_NAME, 5093 /* Unsigned 32-bit bitmap indicating schedule update 5094 * BIT_0: NSS Update 5095 * BIT_1: Channel list update 5096 */ 5097 QCA_WLAN_VENDOR_ATTR_NDP_SCHEDULE_UPDATE_REASON, 5098 /* Unsigned 32-bit value for NSS */ 5099 QCA_WLAN_VENDOR_ATTR_NDP_NSS, 5100 /* Unsigned 32-bit value for NUMBER NDP CHANNEL */ 5101 QCA_WLAN_VENDOR_ATTR_NDP_NUM_CHANNELS, 5102 /* Unsigned 32-bit value for CHANNEL BANDWIDTH 5103 * 0:20 MHz, 1:40 MHz, 2:80 MHz, 3:160 MHz 5104 */ 5105 QCA_WLAN_VENDOR_ATTR_NDP_CHANNEL_WIDTH, 5106 /* Array of channel/band width */ 5107 QCA_WLAN_VENDOR_ATTR_NDP_CHANNEL_INFO, 5108 /* IPv6 address used by NDP (in network byte order), 16 bytes array. 5109 * This attribute is used and optional for ndp request, ndp response, 5110 * ndp indication, and ndp confirm. 5111 */ 5112 QCA_WLAN_VENDOR_ATTR_NDP_IPV6_ADDR = 27, 5113 /* Unsigned 16-bit value indicating transport port used by NDP. 5114 * This attribute is used and optional for ndp response, ndp indication, 5115 * and ndp confirm. 5116 */ 5117 QCA_WLAN_VENDOR_ATTR_NDP_TRANSPORT_PORT = 28, 5118 /* Unsigned 8-bit value indicating protocol used by NDP and assigned by 5119 * the Internet Assigned Numbers Authority (IANA) as per: 5120 * https://www.iana.org/assignments/protocol-numbers/protocol-numbers.xhtml 5121 * This attribute is used and optional for ndp response, ndp indication, 5122 * and ndp confirm. 5123 */ 5124 QCA_WLAN_VENDOR_ATTR_NDP_TRANSPORT_PROTOCOL = 29, 5125 /* Unsigned 8-bit value indicating if NDP remote peer supports NAN NDPE. 5126 * 1:support 0:not support 5127 */ 5128 QCA_WLAN_VENDOR_ATTR_PEER_NDPE_SUPPORT = 30, 5129 5130 /* keep last */ 5131 QCA_WLAN_VENDOR_ATTR_NDP_PARAMS_AFTER_LAST, 5132 QCA_WLAN_VENDOR_ATTR_NDP_PARAMS_MAX = 5133 QCA_WLAN_VENDOR_ATTR_NDP_PARAMS_AFTER_LAST - 1, 5134 }; 5135 5136 enum qca_wlan_ndp_sub_cmd { 5137 QCA_WLAN_VENDOR_ATTR_NDP_INVALID = 0, 5138 /* Command to create a NAN data path interface */ 5139 QCA_WLAN_VENDOR_ATTR_NDP_INTERFACE_CREATE = 1, 5140 /* Command to delete a NAN data path interface */ 5141 QCA_WLAN_VENDOR_ATTR_NDP_INTERFACE_DELETE = 2, 5142 /* Command to initiate a NAN data path session */ 5143 QCA_WLAN_VENDOR_ATTR_NDP_INITIATOR_REQUEST = 3, 5144 /* Command to notify if the NAN data path session was sent */ 5145 QCA_WLAN_VENDOR_ATTR_NDP_INITIATOR_RESPONSE = 4, 5146 /* Command to respond to NAN data path session */ 5147 QCA_WLAN_VENDOR_ATTR_NDP_RESPONDER_REQUEST = 5, 5148 /* Command to notify on the responder about the response */ 5149 QCA_WLAN_VENDOR_ATTR_NDP_RESPONDER_RESPONSE = 6, 5150 /* Command to initiate a NAN data path end */ 5151 QCA_WLAN_VENDOR_ATTR_NDP_END_REQUEST = 7, 5152 /* Command to notify the if end request was sent */ 5153 QCA_WLAN_VENDOR_ATTR_NDP_END_RESPONSE = 8, 5154 /* Command to notify the peer about the end request */ 5155 QCA_WLAN_VENDOR_ATTR_NDP_REQUEST_IND = 9, 5156 /* Command to confirm the NAN data path session is complete */ 5157 QCA_WLAN_VENDOR_ATTR_NDP_CONFIRM_IND = 10, 5158 /* Command to indicate the peer about the end request being received */ 5159 QCA_WLAN_VENDOR_ATTR_NDP_END_IND = 11, 5160 /* Command to indicate the peer of schedule update */ 5161 QCA_WLAN_VENDOR_ATTR_NDP_SCHEDULE_UPDATE_IND = 12 5162 }; 5163 5164 /** 5165 * enum qca_wlan_vendor_attr_nd_offload - Used by the vendor command 5166 * QCA_NL80211_VENDOR_SUBCMD_ND_OFFLOAD. 5167 */ 5168 enum qca_wlan_vendor_attr_nd_offload { 5169 QCA_WLAN_VENDOR_ATTR_ND_OFFLOAD_INVALID = 0, 5170 /* Flag to set Neighbour Discovery offload */ 5171 QCA_WLAN_VENDOR_ATTR_ND_OFFLOAD_FLAG, 5172 /* Keep last */ 5173 QCA_WLAN_VENDOR_ATTR_ND_OFFLOAD_AFTER_LAST, 5174 QCA_WLAN_VENDOR_ATTR_ND_OFFLOAD_MAX = 5175 QCA_WLAN_VENDOR_ATTR_ND_OFFLOAD_AFTER_LAST - 1, 5176 }; 5177 5178 /** 5179 * enum packet_filter_sub_cmd - Packet filter sub commands 5180 */ 5181 enum packet_filter_sub_cmd { 5182 /** 5183 * Write packet filter program and/or data. The driver/firmware should 5184 * disable APF before writing into local buffer and re-enable APF after 5185 * writing is done. 5186 */ 5187 QCA_WLAN_SET_PACKET_FILTER = 1, 5188 /* Get packet filter feature capabilities from driver */ 5189 QCA_WLAN_GET_PACKET_FILTER = 2, 5190 /** 5191 * Write packet filter program and/or data. User space will send the 5192 * %QCA_WLAN_DISABLE_PACKET_FILTER command before issuing this command 5193 * and will send the %QCA_WLAN_ENABLE_PACKET_FILTER afterwards. The key 5194 * difference from that %QCA_WLAN_SET_PACKET_FILTER is the control over 5195 * enable/disable is given to user space with this command. Also, 5196 * user space sends the length of program portion in the buffer within 5197 * %QCA_WLAN_VENDOR_ATTR_PACKET_FILTER_PROG_LENGTH. 5198 */ 5199 QCA_WLAN_WRITE_PACKET_FILTER = 3, 5200 /* Read packet filter program and/or data */ 5201 QCA_WLAN_READ_PACKET_FILTER = 4, 5202 /* Enable APF feature */ 5203 QCA_WLAN_ENABLE_PACKET_FILTER = 5, 5204 /* Disable APF feature */ 5205 QCA_WLAN_DISABLE_PACKET_FILTER = 6, 5206 }; 5207 5208 /** 5209 * enum qca_wlan_vendor_attr_packet_filter - BPF control commands used by 5210 * vendor QCA_NL80211_VENDOR_SUBCMD_PACKET_FILTER. 5211 */ 5212 enum qca_wlan_vendor_attr_packet_filter { 5213 QCA_WLAN_VENDOR_ATTR_PACKET_FILTER_INVALID = 0, 5214 /* Unsigned 32-bit enum passed using packet_filter_sub_cmd */ 5215 QCA_WLAN_VENDOR_ATTR_PACKET_FILTER_SUB_CMD, 5216 /* Unsigned 32-bit value indicating the packet filter version */ 5217 QCA_WLAN_VENDOR_ATTR_PACKET_FILTER_VERSION, 5218 /* Unsigned 32-bit value indicating the packet filter id */ 5219 QCA_WLAN_VENDOR_ATTR_PACKET_FILTER_ID, 5220 /** 5221 * Unsigned 32-bit value indicating the packet filter size including 5222 * program + data. 5223 */ 5224 QCA_WLAN_VENDOR_ATTR_PACKET_FILTER_SIZE, 5225 /* Unsigned 32-bit value indicating the packet filter current offset */ 5226 QCA_WLAN_VENDOR_ATTR_PACKET_FILTER_CURRENT_OFFSET, 5227 /* Program and/or data in bytes */ 5228 QCA_WLAN_VENDOR_ATTR_PACKET_FILTER_PROGRAM, 5229 /* Unsigned 32-bit value of the length of the program section in packet 5230 * filter buffer. 5231 */ 5232 QCA_WLAN_VENDOR_ATTR_PACKET_FILTER_PROG_LENGTH = 7, 5233 5234 /* keep last */ 5235 QCA_WLAN_VENDOR_ATTR_PACKET_FILTER_AFTER_LAST, 5236 QCA_WLAN_VENDOR_ATTR_PACKET_FILTER_MAX = 5237 QCA_WLAN_VENDOR_ATTR_PACKET_FILTER_AFTER_LAST - 1, 5238 }; 5239 5240 /** 5241 * enum qca_wlan_vendor_drv_info - WLAN driver info used by vendor command 5242 * QCA_NL80211_VENDOR_SUBCMD_GET_BUS_SIZE. 5243 */ 5244 enum qca_wlan_vendor_drv_info { 5245 QCA_WLAN_VENDOR_ATTR_DRV_INFO_INVALID = 0, 5246 /* Maximum Message size info between firmware & HOST 5247 * Unsigned 32-bit value 5248 */ 5249 QCA_WLAN_VENDOR_ATTR_DRV_INFO_BUS_SIZE, 5250 /* keep last */ 5251 QCA_WLAN_VENDOR_ATTR_DRV_INFO_AFTER_LAST, 5252 QCA_WLAN_VENDOR_ATTR_DRV_INFO_MAX = 5253 QCA_WLAN_VENDOR_ATTR_DRV_INFO_AFTER_LAST - 1, 5254 }; 5255 5256 /** 5257 * enum qca_wlan_vendor_attr_wake_stats - Wake lock stats used by vendor 5258 * command QCA_NL80211_VENDOR_SUBCMD_GET_WAKE_REASON_STATS. 5259 */ 5260 enum qca_wlan_vendor_attr_wake_stats { 5261 QCA_WLAN_VENDOR_ATTR_WAKE_STATS_INVALID = 0, 5262 /* Unsigned 32-bit value indicating the total count of wake event */ 5263 QCA_WLAN_VENDOR_ATTR_WAKE_STATS_TOTAL_CMD_EVENT_WAKE, 5264 /* Array of individual wake count, each index representing wake reason 5265 */ 5266 QCA_WLAN_VENDOR_ATTR_WAKE_STATS_CMD_EVENT_WAKE_CNT_PTR, 5267 /* Unsigned 32-bit value representing wake count array */ 5268 QCA_WLAN_VENDOR_ATTR_WAKE_STATS_CMD_EVENT_WAKE_CNT_SZ, 5269 /* Unsigned 32-bit total wake count value of driver/fw */ 5270 QCA_WLAN_VENDOR_ATTR_WAKE_STATS_TOTAL_DRIVER_FW_LOCAL_WAKE, 5271 /* Array of wake stats of driver/fw */ 5272 QCA_WLAN_VENDOR_ATTR_WAKE_STATS_DRIVER_FW_LOCAL_WAKE_CNT_PTR, 5273 /* Unsigned 32-bit total wake count value of driver/fw */ 5274 QCA_WLAN_VENDOR_ATTR_WAKE_STATS_DRIVER_FW_LOCAL_WAKE_CNT_SZ, 5275 /* Unsigned 32-bit total wake count value of packets received */ 5276 QCA_WLAN_VENDOR_ATTR_WAKE_STATS_TOTAL_RX_DATA_WAKE, 5277 /* Unsigned 32-bit wake count value unicast packets received */ 5278 QCA_WLAN_VENDOR_ATTR_WAKE_STATS_RX_UNICAST_CNT, 5279 /* Unsigned 32-bit wake count value multicast packets received */ 5280 QCA_WLAN_VENDOR_ATTR_WAKE_STATS_RX_MULTICAST_CNT, 5281 /* Unsigned 32-bit wake count value broadcast packets received */ 5282 QCA_WLAN_VENDOR_ATTR_WAKE_STATS_RX_BROADCAST_CNT, 5283 /* Unsigned 32-bit wake count value of ICMP packets */ 5284 QCA_WLAN_VENDOR_ATTR_WAKE_STATS_ICMP_PKT, 5285 /* Unsigned 32-bit wake count value of ICMP6 packets */ 5286 QCA_WLAN_VENDOR_ATTR_WAKE_STATS_ICMP6_PKT, 5287 /* Unsigned 32-bit value ICMP6 router advertisement */ 5288 QCA_WLAN_VENDOR_ATTR_WAKE_STATS_ICMP6_RA, 5289 /* Unsigned 32-bit value ICMP6 neighbor advertisement */ 5290 QCA_WLAN_VENDOR_ATTR_WAKE_STATS_ICMP6_NA, 5291 /* Unsigned 32-bit value ICMP6 neighbor solicitation */ 5292 QCA_WLAN_VENDOR_ATTR_WAKE_STATS_ICMP6_NS, 5293 /* Unsigned 32-bit wake count value of receive side ICMP4 multicast */ 5294 QCA_WLAN_VENDOR_ATTR_WAKE_STATS_ICMP4_RX_MULTICAST_CNT, 5295 /* Unsigned 32-bit wake count value of receive side ICMP6 multicast */ 5296 QCA_WLAN_VENDOR_ATTR_WAKE_STATS_ICMP6_RX_MULTICAST_CNT, 5297 /* Unsigned 32-bit wake count value of receive side multicast */ 5298 QCA_WLAN_VENDOR_ATTR_WAKE_STATS_OTHER_RX_MULTICAST_CNT, 5299 /* Unsigned 32-bit wake count value of a given RSSI breach */ 5300 QCA_WLAN_VENDOR_ATTR_WAKE_STATS_RSSI_BREACH_CNT, 5301 /* Unsigned 32-bit wake count value of low RSSI */ 5302 QCA_WLAN_VENDOR_ATTR_WAKE_STATS_LOW_RSSI_CNT, 5303 /* Unsigned 32-bit value GSCAN count */ 5304 QCA_WLAN_VENDOR_ATTR_WAKE_STATS_GSCAN_CNT, 5305 /* Unsigned 32-bit value PNO complete count */ 5306 QCA_WLAN_VENDOR_ATTR_WAKE_STATS_PNO_COMPLETE_CNT, 5307 /* Unsigned 32-bit value PNO match count */ 5308 QCA_WLAN_VENDOR_ATTR_WAKE_STATS_PNO_MATCH_CNT, 5309 /* keep last */ 5310 QCA_WLAN_VENDOR_GET_WAKE_STATS_AFTER_LAST, 5311 QCA_WLAN_VENDOR_GET_WAKE_STATS_MAX = 5312 QCA_WLAN_VENDOR_GET_WAKE_STATS_AFTER_LAST - 1, 5313 }; 5314 5315 /** 5316 * enum qca_wlan_vendor_attr_thermal_cmd - Vendor subcmd attributes to set 5317 * cmd value. Used for NL attributes for data used by 5318 * QCA_NL80211_VENDOR_SUBCMD_THERMAL_CMD sub command. 5319 */ 5320 enum qca_wlan_vendor_attr_thermal_cmd { 5321 QCA_WLAN_VENDOR_ATTR_THERMAL_CMD_INVALID = 0, 5322 /* The value of command, driver will implement different operations 5323 * according to this value. It uses values defined in 5324 * enum qca_wlan_vendor_attr_thermal_cmd_type. 5325 * u32 attribute. 5326 */ 5327 QCA_WLAN_VENDOR_ATTR_THERMAL_CMD_VALUE = 1, 5328 5329 /* keep last */ 5330 QCA_WLAN_VENDOR_ATTR_THERMAL_CMD_AFTER_LAST, 5331 QCA_WLAN_VENDOR_ATTR_THERMAL_CMD_MAX = 5332 QCA_WLAN_VENDOR_ATTR_THERMAL_CMD_AFTER_LAST - 1 5333 }; 5334 5335 /** 5336 * qca_wlan_vendor_attr_thermal_cmd_type: Attribute values for 5337 * QCA_WLAN_VENDOR_ATTR_THERMAL_CMD_VALUE to the vendor subcmd 5338 * QCA_NL80211_VENDOR_SUBCMD_THERMAL_CMD. This represents the 5339 * thermal command types sent to driver. 5340 * @QCA_WLAN_VENDOR_ATTR_THERMAL_CMD_TYPE_GET_PARAMS: Request to 5341 * get thermal shutdown configuration parameters for display. Parameters 5342 * responded from driver are defined in 5343 * enum qca_wlan_vendor_attr_get_thermal_params_rsp. 5344 * @QCA_WLAN_VENDOR_ATTR_THERMAL_CMD_TYPE_GET_TEMPERATURE: Request to 5345 * get temperature. Host should respond with a temperature data. It is defined 5346 * in enum qca_wlan_vendor_attr_thermal_get_temperature. 5347 * @QCA_WLAN_VENDOR_ATTR_THERMAL_CMD_TYPE_SUSPEND: Request to execute thermal 5348 * suspend action. 5349 * @QCA_WLAN_VENDOR_ATTR_THERMAL_CMD_TYPE_RESUME: Request to execute thermal 5350 * resume action. 5351 */ 5352 enum qca_wlan_vendor_attr_thermal_cmd_type { 5353 QCA_WLAN_VENDOR_ATTR_THERMAL_CMD_TYPE_GET_PARAMS, 5354 QCA_WLAN_VENDOR_ATTR_THERMAL_CMD_TYPE_GET_TEMPERATURE, 5355 QCA_WLAN_VENDOR_ATTR_THERMAL_CMD_TYPE_SUSPEND, 5356 QCA_WLAN_VENDOR_ATTR_THERMAL_CMD_TYPE_RESUME, 5357 }; 5358 5359 /** 5360 * enum qca_wlan_vendor_attr_thermal_get_temperature - vendor subcmd attributes 5361 * to get chip temperature by user. 5362 * enum values are used for NL attributes for data used by 5363 * QCA_WLAN_VENDOR_ATTR_THERMAL_CMD_TYPE_GET_TEMPERATURE command for data used 5364 * by QCA_NL80211_VENDOR_SUBCMD_THERMAL_CMD sub command. 5365 */ 5366 enum qca_wlan_vendor_attr_thermal_get_temperature { 5367 QCA_WLAN_VENDOR_ATTR_THERMAL_GET_TEMPERATURE_INVALID = 0, 5368 /* Temperature value (degree Celsius) from driver. 5369 * u32 attribute. 5370 */ 5371 QCA_WLAN_VENDOR_ATTR_THERMAL_GET_TEMPERATURE_DATA, 5372 5373 /* keep last */ 5374 QCA_WLAN_VENDOR_ATTR_THERMAL_GET_TEMPERATURE_AFTER_LAST, 5375 QCA_WLAN_VENDOR_ATTR_THERMAL_GET_TEMPERATURE_MAX = 5376 QCA_WLAN_VENDOR_ATTR_THERMAL_GET_TEMPERATURE_AFTER_LAST - 1, 5377 }; 5378 5379 /** 5380 * enum qca_wlan_vendor_attr_get_thermal_params_rsp - vendor subcmd attributes 5381 * to get configuration parameters of thermal shutdown feature. Enum values are 5382 * used by QCA_WLAN_VENDOR_ATTR_THERMAL_CMD_TYPE_GET_PARAMS command for data 5383 * used by QCA_NL80211_VENDOR_SUBCMD_THERMAL_CMD sub command. 5384 */ 5385 enum qca_wlan_vendor_attr_get_thermal_params_rsp { 5386 QCA_WLAN_VENDOR_ATTR_GET_THERMAL_PARAMS_RSP_INVALID = 0, 5387 /* Indicate if the thermal shutdown feature is enabled. 5388 * NLA_FLAG attribute. 5389 */ 5390 QCA_WLAN_VENDOR_ATTR_GET_THERMAL_PARAMS_RSP_SHUTDOWN_EN, 5391 /* Indicate if the auto mode is enabled. 5392 * Enable: Driver triggers the suspend/resume action. 5393 * Disable: User space triggers the suspend/resume action. 5394 * NLA_FLAG attribute. 5395 */ 5396 QCA_WLAN_VENDOR_ATTR_GET_THERMAL_PARAMS_RSP_SHUTDOWN_AUTO_EN, 5397 /* Thermal resume threshold (degree Celsius). Issue the resume command 5398 * if the temperature value is lower than this threshold. 5399 * u16 attribute. 5400 */ 5401 QCA_WLAN_VENDOR_ATTR_GET_THERMAL_PARAMS_RSP_RESUME_THRESH, 5402 /* Thermal warning threshold (degree Celsius). FW reports temperature 5403 * to driver if it's higher than this threshold. 5404 * u16 attribute. 5405 */ 5406 QCA_WLAN_VENDOR_ATTR_GET_THERMAL_PARAMS_RSP_WARNING_THRESH, 5407 /* Thermal suspend threshold (degree Celsius). Issue the suspend command 5408 * if the temperature value is higher than this threshold. 5409 * u16 attribute. 5410 */ 5411 QCA_WLAN_VENDOR_ATTR_GET_THERMAL_PARAMS_RSP_SUSPEND_THRESH, 5412 /* FW reports temperature data periodically at this interval (ms). 5413 * u16 attribute. 5414 */ 5415 QCA_WLAN_VENDOR_ATTR_GET_THERMAL_PARAMS_RSP_SAMPLE_RATE, 5416 5417 /* keep last */ 5418 QCA_WLAN_VENDOR_ATTR_GET_THERMAL_PARAMS_RSP_AFTER_LAST, 5419 QCA_WLAN_VENDOR_ATTR_GET_THERMAL_PARAMS_RSP_MAX = 5420 QCA_WLAN_VENDOR_ATTR_GET_THERMAL_PARAMS_RSP_AFTER_LAST - 1, 5421 }; 5422 5423 /** 5424 * enum qca_wlan_vendor_attr_thermal_event - vendor subcmd attributes to 5425 * report thermal events from driver to user space. 5426 * enum values are used for NL attributes for data used by 5427 * QCA_NL80211_VENDOR_SUBCMD_THERMAL_EVENT sub command. 5428 */ 5429 enum qca_wlan_vendor_attr_thermal_event { 5430 QCA_WLAN_VENDOR_ATTR_THERMAL_EVENT_INVALID = 0, 5431 /* Temperature value (degree Celsius) from driver. 5432 * u32 attribute. 5433 */ 5434 QCA_WLAN_VENDOR_ATTR_THERMAL_EVENT_TEMPERATURE, 5435 /* Indication of resume completion from power save mode. 5436 * NLA_FLAG attribute. 5437 */ 5438 QCA_WLAN_VENDOR_ATTR_THERMAL_EVENT_RESUME_COMPLETE, 5439 5440 /* keep last */ 5441 QCA_WLAN_VENDOR_ATTR_THERMAL_EVENT_AFTER_LAST, 5442 QCA_WLAN_VENDOR_ATTR_THERMAL_EVENT_MAX = 5443 QCA_WLAN_VENDOR_ATTR_THERMAL_EVENT_AFTER_LAST - 1, 5444 }; 5445 5446 /** 5447 * enum he_fragmentation_val - HE fragmentation support values 5448 * Indicates level of dynamic fragmentation that is supported by 5449 * a STA as a recipient. 5450 * HE fragmentation values are defined in IEEE P802.11ax/D2.0, 9.4.2.237.2 5451 * (HE MAC Capabilities Information field) and are used in HE Capabilities 5452 * element to advertise the support. These values are validated in the driver 5453 * to check the device capability and advertised in the HE Capabilities 5454 * element. These values are used to configure testbed device to allow the 5455 * advertised hardware capabilities to be downgraded for testing purposes. 5456 * 5457 * @HE_FRAG_DISABLE: no support for dynamic fragmentation 5458 * @HE_FRAG_LEVEL1: support for dynamic fragments that are 5459 * contained within an MPDU or S-MPDU, no support for dynamic fragments 5460 * within an A-MPDU that is not an S-MPDU. 5461 * @HE_FRAG_LEVEL2: support for dynamic fragments that are 5462 * contained within an MPDU or S-MPDU and support for up to one dynamic 5463 * fragment for each MSDU, each A-MSDU if supported by the recipient, and 5464 * each MMPDU within an A-MPDU or multi-TID A-MPDU that is not an 5465 * MPDU or S-MPDU. 5466 * @HE_FRAG_LEVEL3: support for dynamic fragments that are 5467 * contained within an MPDU or S-MPDU and support for multiple dynamic 5468 * fragments for each MSDU and for each A-MSDU if supported by the 5469 * recipient within an A-MPDU or multi-TID AMPDU and up to one dynamic 5470 * fragment for each MMPDU in a multi-TID A-MPDU that is not an S-MPDU. 5471 */ 5472 enum he_fragmentation_val { 5473 HE_FRAG_DISABLE, 5474 HE_FRAG_LEVEL1, 5475 HE_FRAG_LEVEL2, 5476 HE_FRAG_LEVEL3, 5477 }; 5478 5479 /** 5480 * enum he_mcs_config - HE MCS support configuration 5481 * 5482 * Configures the HE Tx/Rx MCS map in HE capability IE for given bandwidth. 5483 * These values are used in driver to configure the HE MCS map to advertise 5484 * Tx/Rx MCS map in HE capability and these values are applied for all the 5485 * streams supported by the device. To configure MCS for different bandwidths, 5486 * vendor command needs to be sent using this attribute with appropriate value. 5487 * For example, to configure HE_80_MCS_0_7, send vendor command using HE MCS 5488 * attribute with HE_80_MCS0_7. And to configure HE MCS for HE_160_MCS0_11 5489 * send this command using HE MCS config attribute with value HE_160_MCS0_11. 5490 * These values are used to configure testbed device to allow the advertised 5491 * hardware capabilities to be downgraded for testing purposes. The enum values 5492 * are defined such that BIT[1:0] indicates the MCS map value. Values 3,7 and 5493 * 11 are not used as BIT[1:0] value is 3 which is used to disable MCS map. 5494 * These values are validated in the driver before setting the MCS map and 5495 * driver returns error if the input is other than these enum values. 5496 * 5497 * @HE_80_MCS0_7: support for HE 80/40/20 MHz MCS 0 to 7 5498 * @HE_80_MCS0_9: support for HE 80/40/20 MHz MCS 0 to 9 5499 * @HE_80_MCS0_11: support for HE 80/40/20 MHz MCS 0 to 11 5500 * @HE_160_MCS0_7: support for HE 160 MHz MCS 0 to 7 5501 * @HE_160_MCS0_9: support for HE 160 MHz MCS 0 to 9 5502 * @HE_160_MCS0_11: support for HE 160 MHz MCS 0 to 11 5503 * @HE_80P80_MCS0_7: support for HE 80p80 MHz MCS 0 to 7 5504 * @HE_80P80_MCS0_9: support for HE 80p80 MHz MCS 0 to 9 5505 * @HE_80P80_MCS0_11: support for HE 80p80 MHz MCS 0 to 11 5506 */ 5507 enum he_mcs_config { 5508 HE_80_MCS0_7 = 0, 5509 HE_80_MCS0_9 = 1, 5510 HE_80_MCS0_11 = 2, 5511 HE_160_MCS0_7 = 4, 5512 HE_160_MCS0_9 = 5, 5513 HE_160_MCS0_11 = 6, 5514 HE_80P80_MCS0_7 = 8, 5515 HE_80P80_MCS0_9 = 9, 5516 HE_80P80_MCS0_11 = 10, 5517 }; 5518 5519 /** 5520 * enum qca_wlan_ba_session_config - BA session configuration 5521 * 5522 * Indicates the configuration values for BA session configuration attribute. 5523 * 5524 * @QCA_WLAN_ADD_BA: Establish a new BA session with given configuration. 5525 * @QCA_WLAN_DELETE_BA: Delete the existing BA session for given TID. 5526 */ 5527 enum qca_wlan_ba_session_config { 5528 QCA_WLAN_ADD_BA = 1, 5529 QCA_WLAN_DELETE_BA = 2, 5530 }; 5531 5532 /** 5533 * enum qca_wlan_ac_type - Access category type 5534 * 5535 * Indicates the access category type value. 5536 * 5537 * @QCA_WLAN_AC_BE: BE access category 5538 * @QCA_WLAN_AC_BK: BK access category 5539 * @QCA_WLAN_AC_VI: VI access category 5540 * @QCA_WLAN_AC_VO: VO access category 5541 * @QCA_WLAN_AC_ALL: All ACs 5542 */ 5543 enum qca_wlan_ac_type { 5544 QCA_WLAN_AC_BE = 0, 5545 QCA_WLAN_AC_BK = 1, 5546 QCA_WLAN_AC_VI = 2, 5547 QCA_WLAN_AC_VO = 3, 5548 QCA_WLAN_AC_ALL = 4, 5549 }; 5550 5551 /** 5552 * enum qca_wlan_he_ltf_cfg - HE LTF configuration 5553 * 5554 * Indicates the HE LTF configuration value. 5555 * 5556 * @QCA_WLAN_HE_LTF_AUTO: HE-LTF is automatically set to the mandatory HE-LTF, 5557 * based on the GI setting 5558 * @QCA_WLAN_HE_LTF_1X: 1X HE LTF is 3.2us LTF 5559 * @QCA_WLAN_HE_LTF_2X: 2X HE LTF is 6.4us LTF 5560 * @QCA_WLAN_HE_LTF_4X: 4X HE LTF is 12.8us LTF 5561 */ 5562 enum qca_wlan_he_ltf_cfg { 5563 QCA_WLAN_HE_LTF_AUTO = 0, 5564 QCA_WLAN_HE_LTF_1X = 1, 5565 QCA_WLAN_HE_LTF_2X = 2, 5566 QCA_WLAN_HE_LTF_4X = 3, 5567 }; 5568 5569 /** 5570 * enum qca_wlan_he_mac_padding_dur - HE trigger frame MAC padding duration 5571 * 5572 * Indicates the HE trigger frame MAC padding duration value. 5573 * 5574 * @QCA_WLAN_HE_NO_ADDITIONAL_PROCESS_TIME: no additional time required to 5575 * process the trigger frame. 5576 * @QCA_WLAN_HE_8US_OF_PROCESS_TIME: indicates the 8us of processing time for 5577 * trigger frame. 5578 * @QCA_WLAN_HE_16US_OF_PROCESS_TIME: indicates the 16us of processing time for 5579 * trigger frame. 5580 */ 5581 enum qca_wlan_he_mac_padding_dur { 5582 QCA_WLAN_HE_NO_ADDITIONAL_PROCESS_TIME = 0, 5583 QCA_WLAN_HE_8US_OF_PROCESS_TIME = 1, 5584 QCA_WLAN_HE_16US_OF_PROCESS_TIME = 2, 5585 }; 5586 5587 /** 5588 * enum qca_wlan_he_om_ctrl_ch_bw - HE OM control field BW configuration 5589 * 5590 * Indicates the HE Operating mode control channel width setting value. 5591 * 5592 * @QCA_WLAN_HE_OM_CTRL_BW_20M: Primary 20 MHz 5593 * @QCA_WLAN_HE_OM_CTRL_BW_40M: Primary 40 MHz 5594 * @QCA_WLAN_HE_OM_CTRL_BW_80M: Primary 80 MHz 5595 * @QCA_WLAN_HE_OM_CTRL_BW_160M: 160 MHz and 80+80 MHz 5596 */ 5597 enum qca_wlan_he_om_ctrl_ch_bw { 5598 QCA_WLAN_HE_OM_CTRL_BW_20M = 0, 5599 QCA_WLAN_HE_OM_CTRL_BW_40M = 1, 5600 QCA_WLAN_HE_OM_CTRL_BW_80M = 2, 5601 QCA_WLAN_HE_OM_CTRL_BW_160M = 3, 5602 }; 5603 5604 /** 5605 * enum qca_wlan_vendor_attr_he_omi_tx: Represents attributes for 5606 * HE operating mode control transmit request. These attributes are 5607 * sent as part of QCA_WLAN_VENDOR_ATTR_WIFI_TEST_CONFIG_HE_OMI_TX and 5608 * QCA_NL80211_VENDOR_SUBCMD_WIFI_TEST_CONFIGURATION. 5609 * 5610 * @QCA_WLAN_VENDOR_ATTR_HE_OMI_RX_NSS: Mandatory 8-bit unsigned value 5611 * indicates the maximum number of spatial streams, NSS, that the STA 5612 * supports in reception for PPDU bandwidths less than or equal to 80 MHz 5613 * and is set to NSS - 1. 5614 * 5615 * @QCA_WLAN_VENDOR_ATTR_HE_OMI_CH_BW: Mandatory 8-bit unsigned value 5616 * indicates the operating channel width supported by the STA for both 5617 * reception and transmission. Uses enum qca_wlan_he_om_ctrl_ch_bw values. 5618 * 5619 * @QCA_WLAN_VENDOR_ATTR_HE_OMI_ULMU_DISABLE: Mandatory 8-bit unsigned value 5620 * indicates the all trigger based UL MU operations by the STA. 5621 * 0 - UL MU operations are enabled by the STA. 5622 * 1 - All triggered UL MU transmissions are suspended by the STA. 5623 * 5624 * @QCA_WLAN_VENDOR_ATTR_HE_OMI_TX_NSTS: Mandatory 8-bit unsigned value 5625 * indicates the maximum number of space-time streams, NSTS, that 5626 * the STA supports in transmission and is set to NSTS - 1. 5627 * 5628 * @QCA_WLAN_VENDOR_ATTR_HE_OMI_ULMU_DATA_DISABLE: 8-bit unsigned value 5629 * combined with the UL MU Disable subfield and the recipient's setting 5630 * of the OM Control UL MU Data Disable RX Support subfield in the HE MAC 5631 * capabilities to determine which HE TB PPDUs are possible by the 5632 * STA to transmit. 5633 * 0 - UL MU data operations are enabled by the STA. 5634 * 1 - Determine which HE TB PPDU types are allowed by the STA if UL MU disable 5635 * bit is not set, else UL MU Tx is suspended. 5636 * 5637 */ 5638 enum qca_wlan_vendor_attr_he_omi_tx { 5639 QCA_WLAN_VENDOR_ATTR_HE_OMI_INVALID = 0, 5640 QCA_WLAN_VENDOR_ATTR_HE_OMI_RX_NSS = 1, 5641 QCA_WLAN_VENDOR_ATTR_HE_OMI_CH_BW = 2, 5642 QCA_WLAN_VENDOR_ATTR_HE_OMI_ULMU_DISABLE = 3, 5643 QCA_WLAN_VENDOR_ATTR_HE_OMI_TX_NSTS = 4, 5644 QCA_WLAN_VENDOR_ATTR_HE_OMI_ULMU_DATA_DISABLE = 5, 5645 5646 /* keep last */ 5647 QCA_WLAN_VENDOR_ATTR_HE_OMI_AFTER_LAST, 5648 QCA_WLAN_VENDOR_ATTR_HE_OMI_MAX = 5649 QCA_WLAN_VENDOR_ATTR_HE_OMI_AFTER_LAST - 1, 5650 }; 5651 5652 /* Attributes for data used by 5653 * QCA_NL80211_VENDOR_SUBCMD_WIFI_TEST_CONFIGURATION 5654 */ 5655 enum qca_wlan_vendor_attr_wifi_test_config { 5656 QCA_WLAN_VENDOR_ATTR_WIFI_TEST_CONFIG_INVALID = 0, 5657 /* 8-bit unsigned value to configure the driver to enable/disable 5658 * WMM feature. This attribute is used to configure testbed device. 5659 * 1-enable, 0-disable 5660 */ 5661 QCA_WLAN_VENDOR_ATTR_WIFI_TEST_CONFIG_WMM_ENABLE = 1, 5662 5663 /* 8-bit unsigned value to configure the driver to accept/reject 5664 * the addba request from peer. This attribute is used to configure 5665 * the testbed device. 5666 * 1-accept addba, 0-reject addba 5667 */ 5668 QCA_WLAN_VENDOR_ATTR_WIFI_TEST_CONFIG_ACCEPT_ADDBA_REQ = 2, 5669 5670 /* 8-bit unsigned value to configure the driver to send or not to 5671 * send the addba request to peer. 5672 * This attribute is used to configure the testbed device. 5673 * 1-send addba, 0-do not send addba 5674 */ 5675 QCA_WLAN_VENDOR_ATTR_WIFI_TEST_CONFIG_SEND_ADDBA_REQ = 3, 5676 5677 /* 8-bit unsigned value to indicate the HE fragmentation support. 5678 * Uses enum he_fragmentation_val values. 5679 * This attribute is used to configure the testbed device to 5680 * allow the advertised hardware capabilities to be downgraded 5681 * for testing purposes. 5682 */ 5683 QCA_WLAN_VENDOR_ATTR_WIFI_TEST_CONFIG_HE_FRAGMENTATION = 4, 5684 5685 /* 8-bit unsigned value to indicate the HE MCS support. 5686 * Uses enum he_mcs_config values. 5687 * This attribute is used to configure the testbed device to 5688 * allow the advertised hardware capabilities to be downgraded 5689 * for testing purposes. 5690 */ 5691 QCA_WLAN_VENDOR_ATTR_WIFI_TEST_CONFIG_HE_MCS = 5, 5692 5693 /* 8-bit unsigned value to configure the driver to allow or not to 5694 * allow the connection with WEP/TKIP in HT/VHT/HE modes. 5695 * This attribute is used to configure the testbed device. 5696 * 1-allow WEP/TKIP in HT/VHT/HE, 0-do not allow WEP/TKIP. 5697 */ 5698 QCA_WLAN_VENDOR_ATTR_WIFI_TEST_CONFIG_WEP_TKIP_IN_HE = 6, 5699 5700 /* 8-bit unsigned value to configure the driver to add a 5701 * new BA session or delete the existing BA session for 5702 * given TID. ADDBA command uses the buffer size and TID 5703 * configuration if user specifies the values else default 5704 * value for buffer size is used for all TIDs if the TID 5705 * also not specified. For DEL_BA command TID value is 5706 * required to process the command. 5707 * Uses enum qca_wlan_ba_session_config values. 5708 * This attribute is used to configure the testbed device. 5709 */ 5710 QCA_WLAN_VENDOR_ATTR_WIFI_TEST_CONFIG_ADD_DEL_BA_SESSION = 7, 5711 5712 /* 16-bit unsigned value to configure the buffer size in addba 5713 * request and response frames. 5714 * This attribute is used to configure the testbed device. 5715 * The range of the value is 0 to 256. 5716 */ 5717 QCA_WLAN_VENDOR_ATTR_WIFI_TEST_CONFIG_ADDBA_BUFF_SIZE = 8, 5718 5719 /* 8-bit unsigned value to configure the buffer size in addba 5720 * request and response frames. 5721 * This attribute is used to configure the testbed device. 5722 */ 5723 QCA_WLAN_VENDOR_ATTR_WIFI_TEST_CONFIG_BA_TID = 9, 5724 5725 /* 8-bit unsigned value to configure the no ack policy. 5726 * To configure no ack policy, access category value is 5727 * required to process the command. 5728 * This attribute is used to configure the testbed device. 5729 * 1 - enable no ack, 0 - disable no ack. 5730 */ 5731 QCA_WLAN_VENDOR_ATTR_WIFI_TEST_CONFIG_ENABLE_NO_ACK = 10, 5732 5733 /* 8-bit unsigned value to configure the AC for no ack policy 5734 * This attribute is used to configure the testbed device. 5735 * Uses the enum qca_wlan_ac_type values. 5736 */ 5737 QCA_WLAN_VENDOR_ATTR_WIFI_TEST_CONFIG_NO_ACK_AC = 11, 5738 5739 /* 8-bit unsigned value to configure the HE LTF 5740 * This attribute is used to configure the testbed device. 5741 * Uses the enum qca_wlan_he_ltf_cfg values. 5742 */ 5743 QCA_WLAN_VENDOR_ATTR_WIFI_TEST_CONFIG_HE_LTF = 12, 5744 5745 /* 8-bit unsigned value to configure the tx beamformee. 5746 * This attribute is used to configure the testbed device. 5747 * 1-enable, 0-disable. 5748 */ 5749 QCA_WLAN_VENDOR_ATTR_WIFI_TEST_CONFIG_ENABLE_TX_BEAMFORMEE = 13, 5750 5751 /* 8-bit unsigned value to configure the tx beamformee number 5752 * of space-time streams. 5753 * This attribute is used to configure the testbed device. 5754 * The range of the value is 0 to 8. 5755 */ 5756 QCA_WLAN_VENDOR_ATTR_WIFI_TEST_CONFIG_HE_TX_BEAMFORMEE_NSTS = 14, 5757 5758 /* 8-bit unsigned value to configure the MU EDCA params for given AC 5759 * This attribute is used to configure the testbed device. 5760 * Uses the enum qca_wlan_ac_type values. 5761 */ 5762 QCA_WLAN_VENDOR_ATTR_WIFI_TEST_CONFIG_HE_MU_EDCA_AC = 15, 5763 5764 /* 8-bit unsigned value to configure the MU EDCA AIFSN for given AC 5765 * To configure MU EDCA AIFSN value, MU EDCA access category value 5766 * is required to process the command. 5767 * This attribute is used to configure the testbed device. 5768 */ 5769 QCA_WLAN_VENDOR_ATTR_WIFI_TEST_CONFIG_HE_MU_EDCA_AIFSN = 16, 5770 5771 /* 8-bit unsigned value to configure the MU EDCA ECW min value for 5772 * given AC. 5773 * To configure MU EDCA ECW min value, MU EDCA access category value 5774 * is required to process the command. 5775 * This attribute is used to configure the testbed device. 5776 */ 5777 QCA_WLAN_VENDOR_ATTR_WIFI_TEST_CONFIG_HE_MU_EDCA_ECWMIN = 17, 5778 5779 /* 8-bit unsigned value to configure the MU EDCA ECW max value for 5780 * given AC. 5781 * To configure MU EDCA ECW max value, MU EDCA access category value 5782 * is required to process the command. 5783 * This attribute is used to configure the testbed device. 5784 */ 5785 QCA_WLAN_VENDOR_ATTR_WIFI_TEST_CONFIG_HE_MU_EDCA_ECWMAX = 18, 5786 5787 /* 8-bit unsigned value to configure the MU EDCA timer for given AC 5788 * To configure MU EDCA timer value, MU EDCA access category value 5789 * is required to process the command. 5790 * This attribute is used to configure the testbed device. 5791 */ 5792 QCA_WLAN_VENDOR_ATTR_WIFI_TEST_CONFIG_HE_MU_EDCA_TIMER = 19, 5793 5794 /* 8-bit unsigned value to configure the HE trigger frame MAC padding 5795 * duration. 5796 * This attribute is used to configure the testbed device. 5797 * Uses the enum qca_wlan_he_mac_padding_dur values. 5798 */ 5799 QCA_WLAN_VENDOR_ATTR_WIFI_TEST_CONFIG_HE_MAC_PADDING_DUR = 20, 5800 5801 /* 8-bit unsigned value to override the MU EDCA params to defaults 5802 * regardless of the AP beacon MU EDCA params. If it is enabled use 5803 * the default values else use the MU EDCA params from AP beacon. 5804 * This attribute is used to configure the testbed device. 5805 * 1-enable, 0-disable. 5806 */ 5807 QCA_WLAN_VENDOR_ATTR_WIFI_TEST_CONFIG_OVERRIDE_MU_EDCA = 21, 5808 5809 /* 8-bit unsigned value to configure the support for receiving 5810 * an MPDU that contains an operating mode control subfield. 5811 * This attribute is used to configure the testbed device. 5812 * 1-enable, 0-disable. 5813 */ 5814 QCA_WLAN_VENDOR_ATTR_WIFI_TEST_CONFIG_HE_OM_CTRL_SUPP = 22, 5815 5816 /* Nested attribute values required to setup the TWT session. 5817 * enum qca_wlan_vendor_attr_twt_setup provides the necessary 5818 * information to set up the session. It contains broadcast flags, 5819 * set_up flags, trigger value, flow type, flow ID, wake interval 5820 * exponent, protection, target wake time, wake duration, wake interval 5821 * mantissa. These nested attributes are used to setup a host triggered 5822 * TWT session. 5823 */ 5824 QCA_WLAN_VENDOR_ATTR_WIFI_TEST_CONFIG_TWT_SETUP = 23, 5825 5826 /* This nested attribute is used to terminate the current TWT session. 5827 * It does not currently carry any attributes. 5828 */ 5829 QCA_WLAN_VENDOR_ATTR_WIFI_TEST_CONFIG_TWT_TERMINATE = 24, 5830 5831 /* This nested attribute is used to suspend the current TWT session. 5832 * It does not currently carry any attributes. 5833 */ 5834 QCA_WLAN_VENDOR_ATTR_WIFI_TEST_CONFIG_TWT_SUSPEND = 25, 5835 5836 /* Nested attribute values to indicate the request for resume. 5837 * This attribute is used to resume the TWT session. 5838 * enum qca_wlan_vendor_attr_twt_resume provides the necessary 5839 * parameters required to resume the TWT session. 5840 */ 5841 QCA_WLAN_VENDOR_ATTR_WIFI_TEST_CONFIG_TWT_RESUME = 26, 5842 5843 /* 8-bit unsigned value to set the HE operating mode control 5844 * (OM CTRL) Channel Width subfield. 5845 * The Channel Width subfield indicates the operating channel width 5846 * supported by the STA for both reception and transmission. 5847 * Uses the enum qca_wlan_he_om_ctrl_ch_bw values. 5848 * This setting is cleared with the 5849 * QCA_WLAN_VENDOR_ATTR_WIFI_TEST_CONFIG_CLEAR_HE_OM_CTRL_CONFIG 5850 * flag attribute to reset defaults. 5851 * This attribute is used to configure the testbed device. 5852 */ 5853 QCA_WLAN_VENDOR_ATTR_WIFI_TEST_CONFIG_HE_OM_CTRL_BW = 27, 5854 5855 /* 8-bit unsigned value to configure the number of spatial 5856 * streams in HE operating mode control field. 5857 * This setting is cleared with the 5858 * QCA_WLAN_VENDOR_ATTR_WIFI_TEST_CONFIG_CLEAR_HE_OM_CTRL_CONFIG 5859 * flag attribute to reset defaults. 5860 * This attribute is used to configure the testbed device. 5861 */ 5862 QCA_WLAN_VENDOR_ATTR_WIFI_TEST_CONFIG_HE_OM_CTRL_NSS = 28, 5863 5864 /* Flag attribute to configure the UL MU disable bit in 5865 * HE operating mode control field. 5866 * This setting is cleared with the 5867 * QCA_WLAN_VENDOR_ATTR_WIFI_TEST_CONFIG_CLEAR_HE_OM_CTRL_CONFIG 5868 * flag attribute to reset defaults. 5869 * This attribute is used to configure the testbed device. 5870 */ 5871 QCA_WLAN_VENDOR_ATTR_WIFI_TEST_CONFIG_HE_OM_CTRL_UL_MU_DISABLE = 29, 5872 5873 /* Flag attribute to clear the previously set HE operating mode 5874 * control field configuration. 5875 * This attribute is used to configure the testbed device to reset 5876 * defaults to clear any previously set HE operating mode control 5877 * field configuration. 5878 */ 5879 QCA_WLAN_VENDOR_ATTR_WIFI_TEST_CONFIG_CLEAR_HE_OM_CTRL_CONFIG = 30, 5880 5881 /* 8-bit unsigned value to configure HE single user PPDU 5882 * transmission. By default this setting is disabled and it 5883 * is disabled in the reset defaults of the device configuration. 5884 * This attribute is used to configure the testbed device. 5885 * 1-enable, 0-disable 5886 */ 5887 QCA_WLAN_VENDOR_ATTR_WIFI_TEST_CONFIG_HE_TX_SUPPDU = 31, 5888 5889 /* 8-bit unsigned value to configure action frame transmission 5890 * in HE trigger based PPDU transmission. 5891 * By default this setting is disabled and it is disabled in 5892 * the reset defaults of the device configuration. 5893 * This attribute is used to configure the testbed device. 5894 * 1-enable, 0-disable 5895 */ 5896 QCA_WLAN_VENDOR_ATTR_WIFI_TEST_CONFIG_HE_ACTION_TX_TB_PPDU = 32, 5897 5898 /* Nested attribute to indicate HE operating mode control field 5899 * transmission. It contains operating mode control field Nss, 5900 * channel bandwidth, Tx Nsts and UL MU disable attributes. 5901 * These nested attributes are used to send HE operating mode control 5902 * with configured values. 5903 * Uses the enum qca_wlan_vendor_attr_he_omi_tx attributes. 5904 * This attribute is used to configure the testbed device. 5905 */ 5906 QCA_WLAN_VENDOR_ATTR_WIFI_TEST_CONFIG_HE_OMI_TX = 33, 5907 5908 /* 8-bit unsigned value to configure +HTC_HE support to indicate the 5909 * support for the reception of a frame that carries an HE variant 5910 * HT Control field. 5911 * This attribute is used to configure the testbed device. 5912 * 1-enable, 0-disable 5913 */ 5914 QCA_WLAN_VENDOR_ATTR_WIFI_TEST_CONFIG_HE_HTC_HE_SUPP = 34, 5915 5916 /* 8-bit unsigned value to configure VHT support in 2.4G band. 5917 * This attribute is used to configure the testbed device. 5918 * 1-enable, 0-disable 5919 */ 5920 QCA_WLAN_VENDOR_ATTR_WIFI_TEST_CONFIG_ENABLE_2G_VHT = 35, 5921 5922 /* 8-bit unsigned value to configure HE testbed defaults. 5923 * This attribute is used to configure the testbed device. 5924 * 1-set the device HE capabilities to testbed defaults. 5925 * 0-reset the device HE capabilities to supported config. 5926 */ 5927 QCA_WLAN_VENDOR_ATTR_WIFI_TEST_CONFIG_SET_HE_TESTBED_DEFAULTS = 36, 5928 5929 /* 8-bit unsigned value to configure TWT request support. 5930 * This attribute is used to configure the testbed device. 5931 * 1-enable, 0-disable. 5932 */ 5933 QCA_WLAN_VENDOR_ATTR_WIFI_TEST_CONFIG_HE_TWT_REQ_SUPPORT = 37, 5934 5935 /* keep last */ 5936 QCA_WLAN_VENDOR_ATTR_WIFI_TEST_CONFIG_AFTER_LAST, 5937 QCA_WLAN_VENDOR_ATTR_WIFI_TEST_CONFIG_MAX = 5938 QCA_WLAN_VENDOR_ATTR_WIFI_TEST_CONFIG_AFTER_LAST - 1, 5939 }; 5940 5941 /** 5942 * enum qca_wlan_vendor_attr_bss_filter - Used by the vendor command 5943 * QCA_NL80211_VENDOR_SUBCMD_BSS_FILTER. 5944 * The user can add/delete the filter by specifying the BSSID/STA MAC address in 5945 * QCA_WLAN_VENDOR_ATTR_BSS_FILTER_MAC_ADDR, filter type in 5946 * QCA_WLAN_VENDOR_ATTR_BSS_FILTER_TYPE, add/delete action in 5947 * QCA_WLAN_VENDOR_ATTR_BSS_FILTER_ACTION in the request. The user can get the 5948 * statistics of an unassociated station by specifying the MAC address in 5949 * QCA_WLAN_VENDOR_ATTR_BSS_FILTER_MAC_ADDR, station type in 5950 * QCA_WLAN_VENDOR_ATTR_BSS_FILTER_TYPE, GET action in 5951 * QCA_WLAN_VENDOR_ATTR_BSS_FILTER_ACTION in the request. The user also can get 5952 * the statistics of all unassociated stations by specifying the Broadcast MAC 5953 * address (ff:ff:ff:ff:ff:ff) in QCA_WLAN_VENDOR_ATTR_BSS_FILTER_MAC_ADDR with 5954 * above procedure. In the response, driver shall specify statistics 5955 * information nested in QCA_WLAN_VENDOR_ATTR_BSS_FILTER_STA_STATS. 5956 */ 5957 enum qca_wlan_vendor_attr_bss_filter { 5958 QCA_WLAN_VENDOR_ATTR_BSS_FILTER_INVALID = 0, 5959 QCA_WLAN_VENDOR_ATTR_BSS_FILTER_MAC_ADDR = 1, 5960 /* Other BSS filter type, unsigned 8 bit value. One of the values 5961 * in enum qca_wlan_vendor_bss_filter_type. 5962 */ 5963 QCA_WLAN_VENDOR_ATTR_BSS_FILTER_TYPE = 2, 5964 /* Other BSS filter action, unsigned 8 bit value. One of the values 5965 * in enum qca_wlan_vendor_bss_filter_action. 5966 */ 5967 QCA_WLAN_VENDOR_ATTR_BSS_FILTER_ACTION = 3, 5968 /* Array of nested attributes where each entry is the statistics 5969 * information of the specified station that belong to another BSS. 5970 * Attributes for each entry are taken from enum 5971 * qca_wlan_vendor_bss_filter_sta_stats. 5972 * Other BSS station configured in 5973 * QCA_NL80211_VENDOR_SUBCMD_BSS_FILTER with filter type 5974 * QCA_WLAN_VENDOR_BSS_FILTER_TYPE_STA. 5975 * Statistics returned by QCA_NL80211_VENDOR_SUBCMD_BSS_FILTER 5976 * with filter action QCA_WLAN_VENDOR_BSS_FILTER_ACTION_GET. 5977 */ 5978 QCA_WLAN_VENDOR_ATTR_BSS_FILTER_STA_STATS = 4, 5979 5980 /* keep last */ 5981 QCA_WLAN_VENDOR_ATTR_BSS_FILTER_AFTER_LAST, 5982 QCA_WLAN_VENDOR_ATTR_BSS_FILTER_MAX = 5983 QCA_WLAN_VENDOR_ATTR_BSS_FILTER_AFTER_LAST - 1, 5984 }; 5985 5986 /** 5987 * enum qca_wlan_vendor_bss_filter_type - Type of 5988 * filter used in other BSS filter operations. Used by the vendor command 5989 * QCA_NL80211_VENDOR_SUBCMD_BSS_FILTER. 5990 * 5991 * @QCA_WLAN_VENDOR_BSS_FILTER_TYPE_BSSID: BSSID filter 5992 * @QCA_WLAN_VENDOR_BSS_FILTER_TYPE_STA: Station MAC address filter 5993 */ 5994 enum qca_wlan_vendor_bss_filter_type { 5995 QCA_WLAN_VENDOR_BSS_FILTER_TYPE_BSSID, 5996 QCA_WLAN_VENDOR_BSS_FILTER_TYPE_STA, 5997 }; 5998 5999 /** 6000 * enum qca_wlan_vendor_bss_filter_action - Type of 6001 * action in other BSS filter operations. Used by the vendor command 6002 * QCA_NL80211_VENDOR_SUBCMD_BSS_FILTER. 6003 * 6004 * @QCA_WLAN_VENDOR_BSS_FILTER_ACTION_ADD: Add filter 6005 * @QCA_WLAN_VENDOR_BSS_FILTER_ACTION_DEL: Delete filter 6006 * @QCA_WLAN_VENDOR_BSS_FILTER_ACTION_GET: Get the statistics 6007 */ 6008 enum qca_wlan_vendor_bss_filter_action { 6009 QCA_WLAN_VENDOR_BSS_FILTER_ACTION_ADD, 6010 QCA_WLAN_VENDOR_BSS_FILTER_ACTION_DEL, 6011 QCA_WLAN_VENDOR_BSS_FILTER_ACTION_GET, 6012 }; 6013 6014 /** 6015 * enum qca_wlan_vendor_bss_filter_sta_stats - Attributes for 6016 * the statistics of a specific unassociated station belonging to another BSS. 6017 * The statistics provides information of the unassociated station 6018 * filtered by other BSS operation - such as MAC, signal value. 6019 * Used by the vendor command QCA_NL80211_VENDOR_SUBCMD_BSS_FILTER. 6020 * 6021 * @QCA_WLAN_VENDOR_BSS_FILTER_STA_STATS_MAC: MAC address of the station. 6022 * @QCA_WLAN_VENDOR_BSS_FILTER_STA_STATS_RSSI: Last received signal strength 6023 * of the station. Unsigned 8 bit number containing RSSI. 6024 * @QCA_WLAN_VENDOR_BSS_FILTER_STA_STATS_RSSI_TS: Time stamp of the host 6025 * driver for the last received RSSI. Unsigned 64 bit number containing 6026 * nanoseconds from the boottime. 6027 */ 6028 enum qca_wlan_vendor_bss_filter_sta_stats { 6029 QCA_WLAN_VENDOR_BSS_FILTER_STA_STATS_INVALID = 0, 6030 QCA_WLAN_VENDOR_BSS_FILTER_STA_STATS_MAC = 1, 6031 QCA_WLAN_VENDOR_BSS_FILTER_STA_STATS_RSSI = 2, 6032 QCA_WLAN_VENDOR_BSS_FILTER_STA_STATS_RSSI_TS = 3, 6033 6034 /* keep last */ 6035 QCA_WLAN_VENDOR_BSS_FILTER_STA_STATS_AFTER_LAST, 6036 QCA_WLAN_VENDOR_BSS_FILTER_STA_STATS_MAX = 6037 QCA_WLAN_VENDOR_BSS_FILTER_STA_STATS_AFTER_LAST - 1 6038 }; 6039 6040 /* enum qca_wlan_nan_subcmd_type - Type of NAN command used by attribute 6041 * QCA_WLAN_VENDOR_ATTR_NAN_SUBCMD_TYPE as a part of vendor command 6042 * QCA_NL80211_VENDOR_SUBCMD_NAN_EXT. 6043 */ 6044 enum qca_wlan_nan_ext_subcmd_type { 6045 /* Subcmd of type NAN Enable Request */ 6046 QCA_WLAN_NAN_EXT_SUBCMD_TYPE_ENABLE_REQ = 1, 6047 /* Subcmd of type NAN Disable Request */ 6048 QCA_WLAN_NAN_EXT_SUBCMD_TYPE_DISABLE_REQ = 2, 6049 }; 6050 6051 /** 6052 * enum qca_wlan_vendor_attr_nan_params - Used by the vendor command 6053 * QCA_NL80211_VENDOR_SUBCMD_NAN_EXT. 6054 */ 6055 enum qca_wlan_vendor_attr_nan_params { 6056 QCA_WLAN_VENDOR_ATTR_NAN_INVALID = 0, 6057 /* Carries NAN command for firmware component. Every vendor command 6058 * QCA_NL80211_VENDOR_SUBCMD_NAN_EXT must contain this attribute with a 6059 * payload containing the NAN command. NLA_BINARY attribute. 6060 */ 6061 QCA_WLAN_VENDOR_ATTR_NAN_CMD_DATA = 1, 6062 /* Indicates the type of NAN command sent with 6063 * QCA_NL80211_VENDOR_SUBCMD_NAN_EXT. enum qca_wlan_nan_ext_subcmd_type 6064 * describes the possible range of values. This attribute is mandatory 6065 * if the command being issued is either 6066 * QCA_WLAN_NAN_EXT_SUBCMD_TYPE_ENABLE_REQ or 6067 * QCA_WLAN_NAN_EXT_SUBCMD_TYPE_DISABLE_REQ. NLA_U32 attribute. 6068 */ 6069 QCA_WLAN_VENDOR_ATTR_NAN_SUBCMD_TYPE = 2, 6070 /* Frequency (in MHz) of primary NAN discovery social channel in 2.4 GHz 6071 * band. This attribute is mandatory when command type is 6072 * QCA_WLAN_NAN_EXT_SUBCMD_TYPE_ENABLE_REQ. NLA_U32 attribute. 6073 */ 6074 QCA_WLAN_VENDOR_ATTR_NAN_DISC_24GHZ_BAND_FREQ = 3, 6075 /* Frequency (in MHz) of secondary NAN discovery social channel in 5 GHz 6076 * band. This attribute is optional and should be included when command 6077 * type is QCA_WLAN_NAN_EXT_SUBCMD_TYPE_ENABLE_REQ and NAN discovery 6078 * has to be started on 5GHz along with 2.4GHz. NLA_U32 attribute. 6079 */ 6080 QCA_WLAN_VENDOR_ATTR_NAN_DISC_5GHZ_BAND_FREQ = 4, 6081 6082 /* keep last */ 6083 QCA_WLAN_VENDOR_ATTR_NAN_PARAMS_AFTER_LAST, 6084 QCA_WLAN_VENDOR_ATTR_NAN_PARAMS_MAX = 6085 QCA_WLAN_VENDOR_ATTR_NAN_PARAMS_AFTER_LAST - 1 6086 }; 6087 6088 /** 6089 * enum qca_wlan_vendor_attr_twt_setup: Represents attributes for 6090 * TWT (Target Wake Time) setup request. These attributes are sent as part of 6091 * %QCA_WLAN_VENDOR_ATTR_WIFI_TEST_CONFIG_TWT_SETUP and 6092 * %QCA_NL80211_VENDOR_SUBCMD_WIFI_TEST_CONFIGURATION. 6093 * 6094 * @QCA_WLAN_VENDOR_ATTR_TWT_SETUP_BCAST: Flag attribute. 6095 * Disable (flag attribute not present) - Individual TWT 6096 * Enable (flag attribute present) - Broadcast TWT. 6097 * Individual means the session is between the STA and the AP. 6098 * This session is established using a separate negotiation between 6099 * STA and AP. 6100 * Broadcast means the session is across multiple STAs and an AP. The 6101 * configuration parameters are announced in Beacon frames by the AP. 6102 * 6103 * @QCA_WLAN_VENDOR_ATTR_TWT_SETUP_REQ_TYPE: Required (u8). 6104 * Unsigned 8-bit qca_wlan_vendor_twt_setup_req_type to 6105 * specify the TWT request type 6106 * 6107 * @QCA_WLAN_VENDOR_ATTR_TWT_SETUP_TRIGGER: Flag attribute 6108 * Enable (flag attribute present) - TWT with trigger support. 6109 * Disable (flag attribute not present) - TWT without trigger support. 6110 * Trigger means the AP will send the trigger frame to allow STA to send data. 6111 * Without trigger, the STA will wait for the MU EDCA timer before 6112 * transmitting the data. 6113 * 6114 * @QCA_WLAN_VENDOR_ATTR_TWT_SETUP_FLOW_TYPE: Required (u8) 6115 * 0 - Announced TWT - In this mode, STA may skip few service periods to 6116 * save more power. If STA wants to wake up, it will send a PS-POLL/QoS 6117 * NULL frame to AP. 6118 * 1 - Unannounced TWT - The STA will wakeup during every SP. 6119 * 6120 * @QCA_WLAN_VENDOR_ATTR_TWT_SETUP_FLOW_ID: Optional (u8) 6121 * Flow ID is the unique identifier for each TWT session. 6122 * Currently this is not required and dialog ID will be set to zero. 6123 * 6124 * @QCA_WLAN_VENDOR_ATTR_TWT_SETUP_WAKE_INTVL_EXP: Required (u8) 6125 * This attribute (exp) is used along with the mantissa to derive the 6126 * wake interval using the following formula: 6127 * pow(2,exp) = wake_intvl_us/wake_intvl_mantis 6128 * Wake interval is the interval between 2 successive SP. 6129 * 6130 * @QCA_WLAN_VENDOR_ATTR_TWT_SETUP_PROTECTION: Flag attribute 6131 * Enable (flag attribute present) - Protection required. 6132 * Disable (flag attribute not present) - Protection not required. 6133 * If protection is enabled, then the AP will use protection 6134 * mechanism using RTS/CTS to self to reserve the airtime. 6135 * 6136 * @QCA_WLAN_VENDOR_ATTR_TWT_SETUP_WAKE_TIME: Optional (u32) 6137 * This attribute is used as the SP offset which is the offset from 6138 * TSF after which the wake happens. The units are in microseconds. If 6139 * this attribute is not provided, then the value will be set to zero. 6140 * 6141 * @QCA_WLAN_VENDOR_ATTR_TWT_SETUP_WAKE_DURATION: Required (u32) 6142 * This is the duration of the service period. The units are in TU. 6143 * 6144 * @QCA_WLAN_VENDOR_ATTR_TWT_SETUP_WAKE_INTVL_MANTISSA: Required (u32) 6145 * This attribute is used to configure wake interval mantissa. 6146 * The units are in TU. 6147 */ 6148 enum qca_wlan_vendor_attr_twt_setup { 6149 QCA_WLAN_VENDOR_ATTR_TWT_SETUP_INVALID = 0, 6150 QCA_WLAN_VENDOR_ATTR_TWT_SETUP_BCAST = 1, 6151 QCA_WLAN_VENDOR_ATTR_TWT_SETUP_REQ_TYPE = 2, 6152 QCA_WLAN_VENDOR_ATTR_TWT_SETUP_TRIGGER = 3, 6153 QCA_WLAN_VENDOR_ATTR_TWT_SETUP_FLOW_TYPE = 4, 6154 QCA_WLAN_VENDOR_ATTR_TWT_SETUP_FLOW_ID = 5, 6155 QCA_WLAN_VENDOR_ATTR_TWT_SETUP_WAKE_INTVL_EXP = 6, 6156 QCA_WLAN_VENDOR_ATTR_TWT_SETUP_PROTECTION = 7, 6157 QCA_WLAN_VENDOR_ATTR_TWT_SETUP_WAKE_TIME = 8, 6158 QCA_WLAN_VENDOR_ATTR_TWT_SETUP_WAKE_DURATION = 9, 6159 QCA_WLAN_VENDOR_ATTR_TWT_SETUP_WAKE_INTVL_MANTISSA = 10, 6160 6161 /* keep last */ 6162 QCA_WLAN_VENDOR_ATTR_TWT_SETUP_AFTER_LAST, 6163 QCA_WLAN_VENDOR_ATTR_TWT_SETUP_MAX = 6164 QCA_WLAN_VENDOR_ATTR_TWT_SETUP_AFTER_LAST - 1, 6165 }; 6166 6167 /** 6168 * enum qca_wlan_vendor_attr_twt_resume: Represents attributes for 6169 * TWT (Target Wake Time) resume request. These attributes are sent as part of 6170 * %QCA_WLAN_VENDOR_ATTR_WIFI_TEST_CONFIG_TWT_RESUME and 6171 * %QCA_NL80211_VENDOR_SUBCMD_WIFI_TEST_CONFIGURATION. 6172 * 6173 * @QCA_WLAN_VENDOR_ATTR_TWT_RESUME_NEXT_TWT: Optional (u8) 6174 * This attribute is used as the SP offset which is the offset from 6175 * TSF after which the wake happens. The units are in microseconds. 6176 * If this attribute is not provided, then the value will be set to 6177 * zero. 6178 * 6179 * @QCA_WLAN_VENDOR_ATTR_TWT_RESUME_NEXT_TWT_SIZE: Required (u32) 6180 * This attribute represents the next TWT subfield size. 6181 */ 6182 enum qca_wlan_vendor_attr_twt_resume { 6183 QCA_WLAN_VENDOR_ATTR_TWT_RESUME_INVALID = 0, 6184 QCA_WLAN_VENDOR_ATTR_TWT_RESUME_NEXT_TWT = 1, 6185 QCA_WLAN_VENDOR_ATTR_TWT_RESUME_NEXT_TWT_SIZE = 2, 6186 6187 /* keep last */ 6188 QCA_WLAN_VENDOR_ATTR_TWT_RESUME_AFTER_LAST, 6189 QCA_WLAN_VENDOR_ATTR_TWT_RESUME_MAX = 6190 QCA_WLAN_VENDOR_ATTR_TWT_RESUME_AFTER_LAST - 1, 6191 }; 6192 6193 /** 6194 * enum qca_wlan_vendor_twt_setup_req_type - Required (u8) 6195 * Represents the setup type being requested for TWT. 6196 * @QCA_WLAN_VENDOR_TWT_SETUP_REQUEST: STA is not specifying all the TWT 6197 * parameters but relying on AP to fill the parameters during the negotiation. 6198 * @QCA_WLAN_VENDOR_TWT_SETUP_SUGGEST: STA will provide all the suggested 6199 * values which the AP may accept or AP may provide alternative parameters 6200 * which the STA may accept. 6201 * @QCA_WLAN_VENDOR_TWT_SETUP_DEMAND: STA is not willing to accept any 6202 * alternate parameters than the requested ones. 6203 */ 6204 enum qca_wlan_vendor_twt_setup_req_type { 6205 QCA_WLAN_VENDOR_TWT_SETUP_REQUEST = 1, 6206 QCA_WLAN_VENDOR_TWT_SETUP_SUGGEST = 2, 6207 QCA_WLAN_VENDOR_TWT_SETUP_DEMAND = 3, 6208 }; 6209 6210 /** 6211 * enum qca_wlan_roam_scan_event_type - Type of roam scan event 6212 * 6213 * Indicates the type of roam scan event sent by firmware/driver. 6214 * 6215 * @QCA_WLAN_ROAM_SCAN_TRIGGER_EVENT: Roam scan trigger event type. 6216 * @QCA_WLAN_ROAM_SCAN_STOP_EVENT: Roam scan stopped event type. 6217 */ 6218 enum qca_wlan_roam_scan_event_type { 6219 QCA_WLAN_ROAM_SCAN_TRIGGER_EVENT = 0, 6220 QCA_WLAN_ROAM_SCAN_STOP_EVENT = 1, 6221 }; 6222 6223 /** 6224 * enum qca_wlan_roam_scan_trigger_reason - Roam scan trigger reason 6225 * 6226 * Indicates the reason for triggering roam scan by firmware/driver. 6227 * 6228 * @QCA_WLAN_ROAM_SCAN_TRIGGER_REASON_LOW_RSSI: Due to low RSSI of current AP. 6229 * @QCA_WLAN_ROAM_SCAN_TRIGGER_REASON_HIGH_PER: Due to high packet error rate. 6230 */ 6231 enum qca_wlan_roam_scan_trigger_reason { 6232 QCA_WLAN_ROAM_SCAN_TRIGGER_REASON_LOW_RSSI = 0, 6233 QCA_WLAN_ROAM_SCAN_TRIGGER_REASON_HIGH_PER = 1, 6234 }; 6235 6236 /** 6237 * enum qca_wlan_vendor_attr_roam_scan - Vendor subcmd attributes to report 6238 * roam scan related details from driver/firmware to user space. enum values 6239 * are used for NL attributes sent with 6240 * %QCA_NL80211_VENDOR_SUBCMD_ROAM_SCAN_EVENT sub command. 6241 */ 6242 enum qca_wlan_vendor_attr_roam_scan { 6243 QCA_WLAN_VENDOR_ATTR_ROAM_SCAN_INVALID = 0, 6244 /* Encapsulates type of roam scan event being reported. enum 6245 * qca_wlan_roam_scan_event_type describes the possible range of 6246 * values. u32 attribute. 6247 */ 6248 QCA_WLAN_VENDOR_ATTR_ROAM_SCAN_EVENT_TYPE = 1, 6249 /* Encapsulates reason for triggering roam scan. enum 6250 * qca_wlan_roam_scan_trigger_reason describes the possible range of 6251 * values. u32 attribute. 6252 */ 6253 QCA_WLAN_VENDOR_ATTR_ROAM_SCAN_TRIGGER_REASON = 2, 6254 6255 /* keep last */ 6256 QCA_WLAN_VENDOR_ATTR_ROAM_SCAN_AFTER_LAST, 6257 QCA_WLAN_VENDOR_ATTR_ROAM_SCAN_MAX = 6258 QCA_WLAN_VENDOR_ATTR_ROAM_SCAN_AFTER_LAST - 1, 6259 }; 6260 6261 /** 6262 * enum qca_wlan_vendor_cfr_method - QCA vendor CFR methods used by 6263 * attribute QCA_WLAN_VENDOR_ATTR_PEER_CFR_METHOD as part of vendor 6264 * command QCA_NL80211_VENDOR_SUBCMD_PEER_CFR_CAPTURE_CFG. 6265 */ 6266 enum qca_wlan_vendor_cfr_method { 6267 /* CFR method using QOS Null frame */ 6268 QCA_WLAN_VENDOR_CFR_METHOD_QOS_NULL = 0, 6269 }; 6270 6271 /** 6272 * enum qca_wlan_vendor_peer_cfr_capture_attr - Used by the vendor command 6273 * QCA_NL80211_VENDOR_SUBCMD_PEER_CFR_CAPTURE_CFG to configure peer 6274 * Channel Frequency Response capture parameters and enable periodic CFR 6275 * capture. 6276 */ 6277 enum qca_wlan_vendor_peer_cfr_capture_attr { 6278 QCA_WLAN_VENDOR_ATTR_PEER_CFR_CAPTURE_INVALID = 0, 6279 /* 6-byte MAC address of the peer. 6280 * This attribute is mandatory. 6281 */ 6282 QCA_WLAN_VENDOR_ATTR_CFR_PEER_MAC_ADDR = 1, 6283 /* Enable peer CFR Capture, flag attribute. 6284 * This attribute is mandatory to enable peer CFR capture. 6285 * If this attribute is not present, peer CFR capture is disabled. 6286 */ 6287 QCA_WLAN_VENDOR_ATTR_PEER_CFR_ENABLE = 2, 6288 /* BW of measurement, attribute uses the values in enum nl80211_chan_width 6289 * Supported values: 20, 40, 80, 80+80, 160. 6290 * Note that all targets may not support all bandwidths. 6291 * u8 attribute. This attribute is mandatory if attribute 6292 * QCA_WLAN_VENDOR_ATTR_PEER_CFR_ENABLE is used. 6293 */ 6294 QCA_WLAN_VENDOR_ATTR_PEER_CFR_BANDWIDTH = 3, 6295 /* Periodicity of CFR measurement in msec. 6296 * Periodicity should be a multiple of Base timer. 6297 * Current Base timer value supported is 10 msecs (default). 6298 * 0 for one shot capture. u32 attribute. 6299 * This attribute is mandatory if attribute 6300 * QCA_WLAN_VENDOR_ATTR_PEER_CFR_ENABLE is used. 6301 */ 6302 QCA_WLAN_VENDOR_ATTR_PEER_CFR_PERIODICITY = 4, 6303 /* Method used to capture Channel Frequency Response. 6304 * Attribute uses the values defined in enum qca_wlan_vendor_cfr_method. 6305 * u8 attribute. This attribute is mandatory if attribute 6306 * QCA_WLAN_VENDOR_ATTR_PEER_CFR_ENABLE is used. 6307 */ 6308 QCA_WLAN_VENDOR_ATTR_PEER_CFR_METHOD = 5, 6309 /* Enable periodic CFR capture, flag attribute. 6310 * This attribute is mandatory to enable Periodic CFR capture. 6311 * If this attribute is not present, periodic CFR capture is disabled. 6312 */ 6313 QCA_WLAN_VENDOR_ATTR_PERIODIC_CFR_CAPTURE_ENABLE = 6, 6314 6315 /* Keep last */ 6316 QCA_WLAN_VENDOR_ATTR_PEER_CFR_AFTER_LAST, 6317 QCA_WLAN_VENDOR_ATTR_PEER_CFR_MAX = 6318 QCA_WLAN_VENDOR_ATTR_PEER_CFR_AFTER_LAST - 1, 6319 }; 6320 6321 /** 6322 * enum qca_wlan_throughput_level - Current throughput level 6323 * 6324 * Indicates the current level of throughput calculated by the driver. The 6325 * driver may choose different thresholds to decide whether the throughput level 6326 * is low or medium or high based on variety of parameters like physical link 6327 * capacity of the current connection, the number of packets being dispatched 6328 * per second, etc. The throughput level events might not be consistent with the 6329 * actual current throughput value being observed. 6330 * 6331 * @QCA_WLAN_THROUGHPUT_LEVEL_LOW: Low level of throughput 6332 * @QCA_WLAN_THROUGHPUT_LEVEL_MEDIUM: Medium level of throughput 6333 * @QCA_WLAN_THROUGHPUT_LEVEL_HIGH: High level of throughput 6334 */ 6335 enum qca_wlan_throughput_level { 6336 QCA_WLAN_THROUGHPUT_LEVEL_LOW = 0, 6337 QCA_WLAN_THROUGHPUT_LEVEL_MEDIUM = 1, 6338 QCA_WLAN_THROUGHPUT_LEVEL_HIGH = 2, 6339 }; 6340 6341 /** 6342 * enum qca_wlan_vendor_attr_throughput_change - Vendor subcmd attributes to 6343 * report throughput changes from the driver to user space. enum values are used 6344 * for netlink attributes sent with 6345 * %QCA_NL80211_VENDOR_SUBCMD_THROUGHPUT_CHANGE_EVENT sub command. 6346 */ 6347 enum qca_wlan_vendor_attr_throughput_change { 6348 QCA_WLAN_VENDOR_ATTR_THROUGHPUT_CHANGE_INVALID = 0, 6349 /* Indicates the direction of throughput in which the change is being 6350 * reported. u8 attribute. Value is 0 for TX and 1 for RX. 6351 */ 6352 QCA_WLAN_VENDOR_ATTR_THROUGHPUT_CHANGE_DIRECTION = 1, 6353 /* Indicates the newly observed throughput level. enum 6354 * qca_wlan_throughput_level describes the possible range of values. 6355 * u8 attribute. 6356 */ 6357 QCA_WLAN_VENDOR_ATTR_THROUGHPUT_CHANGE_THROUGHPUT_LEVEL = 2, 6358 /* Indicates the driver's guidance on the new value to be set to 6359 * kernel's TCP parameter tcp_limit_output_bytes. u32 attribute. The 6360 * driver may optionally include this attribute. 6361 */ 6362 QCA_WLAN_VENDOR_ATTR_THROUGHPUT_CHANGE_TCP_LIMIT_OUTPUT_BYTES = 3, 6363 /* Indicates the driver's guidance on the new value to be set to 6364 * kernel's TCP parameter tcp_adv_win_scale. s8 attribute. Possible 6365 * values are from -31 to 31. The driver may optionally include this 6366 * attribute. 6367 */ 6368 QCA_WLAN_VENDOR_ATTR_THROUGHPUT_CHANGE_TCP_ADV_WIN_SCALE = 4, 6369 /* Indicates the driver's guidance on the new value to be set to 6370 * kernel's TCP parameter tcp_delack_seg. u32 attribute. The driver may 6371 * optionally include this attribute. 6372 */ 6373 QCA_WLAN_VENDOR_ATTR_THROUGHPUT_CHANGE_TCP_DELACK_SEG = 5, 6374 6375 /* keep last */ 6376 QCA_WLAN_VENDOR_ATTR_THROUGHPUT_CHANGE_AFTER_LAST, 6377 QCA_WLAN_VENDOR_ATTR_THROUGHPUT_CHANGE_MAX = 6378 QCA_WLAN_VENDOR_ATTR_THROUGHPUT_CHANGE_AFTER_LAST - 1, 6379 }; 6380 6381 /** 6382 * enum qca_coex_config_profiles - This enum defines different types of 6383 * traffic streams that can be prioritized one over the other during coex 6384 * scenarios. 6385 * The types defined in this enum are categorized in the below manner. 6386 * 0 - 31 values corresponds to WLAN 6387 * 32 - 63 values corresponds to BT 6388 * 64 - 95 values corresponds to Zigbee 6389 * @QCA_WIFI_STA_DISCOVERY: Prioritize discovery frames for WLAN STA 6390 * @QCA_WIFI_STA_CONNECTION: Prioritize connection frames for WLAN STA 6391 * @QCA_WIFI_STA_CLASS_3_MGMT: Prioritize class 3 mgmt frames for WLAN STA 6392 * @QCA_WIFI_STA_DATA : Prioritize data frames for WLAN STA 6393 * @QCA_WIFI_STA_ALL: Priritize all frames for WLAN STA 6394 * @QCA_WIFI_SAP_DISCOVERY: Prioritize discovery frames for WLAN SAP 6395 * @QCA_WIFI_SAP_CONNECTION: Prioritize connection frames for WLAN SAP 6396 * @QCA_WIFI_SAP_CLASS_3_MGMT: Prioritize class 3 mgmt frames for WLAN SAP 6397 * @QCA_WIFI_SAP_DATA: Prioritize data frames for WLAN SAP 6398 * @QCA_WIFI_SAP_ALL: Prioritize all frames for WLAN SAP 6399 * @QCA_BT_A2DP: Prioritize BT A2DP 6400 * @QCA_BT_BLE: Prioritize BT BLE 6401 * @QCA_BT_SCO: Prioritize BT SCO 6402 * @QCA_ZB_LOW: Prioritize Zigbee Low 6403 * @QCA_ZB_HIGH: Prioritize Zigbee High 6404 */ 6405 enum qca_coex_config_profiles { 6406 /* 0 - 31 corresponds to WLAN */ 6407 QCA_WIFI_STA_DISCOVERY = 0, 6408 QCA_WIFI_STA_CONNECTION = 1, 6409 QCA_WIFI_STA_CLASS_3_MGMT = 2, 6410 QCA_WIFI_STA_DATA = 3, 6411 QCA_WIFI_STA_ALL = 4, 6412 QCA_WIFI_SAP_DISCOVERY = 5, 6413 QCA_WIFI_SAP_CONNECTION = 6, 6414 QCA_WIFI_SAP_CLASS_3_MGMT = 7, 6415 QCA_WIFI_SAP_DATA = 8, 6416 QCA_WIFI_SAP_ALL = 9, 6417 QCA_WIFI_CASE_MAX = 31, 6418 /* 32 - 63 corresponds to BT */ 6419 QCA_BT_A2DP = 32, 6420 QCA_BT_BLE = 33, 6421 QCA_BT_SCO = 34, 6422 QCA_BT_CASE_MAX = 63, 6423 /* 64 - 95 corresponds to Zigbee */ 6424 QCA_ZB_LOW = 64, 6425 QCA_ZB_HIGH = 65, 6426 QCA_ZB_CASE_MAX = 95, 6427 /* 0xff is default value if the u8 profile value is not set. */ 6428 QCA_COEX_CONFIG_PROFILE_DEFAULT_VALUE = 255 6429 }; 6430 6431 /** 6432 * enum qca_vendor_attr_coex_config_types - Coex configurations types. 6433 * This enum defines the valid set of values of coex configuration types. These 6434 * values may used by attribute 6435 * %QCA_VENDOR_ATTR_COEX_CONFIG_THREE_WAY_CONFIG_TYPE. 6436 * 6437 * @QCA_WLAN_VENDOR_ATTR_COEX_CONFIG_THREE_WAY_COEX_RESET: Reset all the 6438 * weights to default values. 6439 * @QCA_WLAN_VENDOR_ATTR_COEX_CONFIG_THREE_WAY_COEX_START: Start to config 6440 * weights with configurability value. 6441 */ 6442 enum qca_vendor_attr_coex_config_types { 6443 QCA_WLAN_VENDOR_ATTR_COEX_CONFIG_INVALID = 0, 6444 QCA_WLAN_VENDOR_ATTR_COEX_CONFIG_THREE_WAY_COEX_RESET = 1, 6445 QCA_WLAN_VENDOR_ATTR_COEX_CONFIG_THREE_WAY_COEX_START = 2, 6446 }; 6447 6448 /** 6449 * enum qca_vendor_attr_coex_config - Specifies vendor coex config attributes 6450 * 6451 * @QCA_VENDOR_ATTR_COEX_CONFIG_PROFILES: This attribute contains variable 6452 * length array of 8-bit values from enum qca_coex_config_profiles. 6453 * FW will prioritize the profiles in the order given in the array encapsulated 6454 * in this attribute. 6455 * For example: 6456 * ----------------------------------------------------------------------- 6457 * | 1 | 34 | 32 | 65 | 6458 * ----------------------------------------------------------------------- 6459 * If the attribute contains the values defined in above array then it means 6460 * 1) Wifi STA connection has priority over BT_SCO, BT_A2DP and ZIGBEE HIGH. 6461 * 2) BT_SCO has priority over BT_A2DP. 6462 * 3) BT_A2DP has priority over ZIGBEE HIGH. 6463 * Profiles which are not listed in this array shall not be preferred over the 6464 * profiles which are listed in the array as a part of this attribute. 6465 */ 6466 enum qca_vendor_attr_coex_config { 6467 QCA_VENDOR_ATTR_COEX_CONFIG_INVALID = 0, 6468 QCA_VENDOR_ATTR_COEX_CONFIG_PROFILES = 1, 6469 6470 /* Keep last */ 6471 QCA_VENDOR_ATTR_COEX_CONFIG_AFTER_LAST, 6472 QCA_VENDOR_ATTR_COEX_CONFIG_MAX = 6473 QCA_VENDOR_ATTR_COEX_CONFIG_AFTER_LAST - 1, 6474 }; 6475 6476 /** 6477 * enum qca_vendor_attr_coex_config_three_way - Specifies vendor coex config 6478 * attributes 6479 * Attributes for data used by QCA_NL80211_VENDOR_SUBCMD_COEX_CONFIG 6480 * 6481 * QCA_VENDOR_ATTR_COEX_CONFIG_THREE_WAY_CONFIG_TYPE: u32 attribute. 6482 * Indicate config type. 6483 * The config types are 32-bit values from qca_vendor_attr_coex_config_types 6484 * 6485 * @QCA_VENDOR_ATTR_COEX_CONFIG_THREE_WAY_PRIORITY_1: u32 attribute. 6486 * Indicate the Priority 1 profiles. 6487 * The profiles are 8-bit values from enum qca_coex_config_profiles. 6488 * In same priority level, maximum to 4 profiles can be set here. 6489 * @QCA_VENDOR_ATTR_COEX_CONFIG_THREE_WAY_PRIORITY_2: u32 attribute. 6490 * Indicate the Priority 2 profiles. 6491 * The profiles are 8-bit values from enum qca_coex_config_profiles. 6492 * In same priority level, maximum to 4 profiles can be set here. 6493 * @QCA_VENDOR_ATTR_COEX_CONFIG_THREE_WAY_PRIORITY_3: u32 attribute. 6494 * Indicate the Priority 3 profiles. 6495 * The profiles are 8-bit values from enum qca_coex_config_profiles. 6496 * In same priority level, maximum to 4 profiles can be set here. 6497 * @QCA_VENDOR_ATTR_COEX_CONFIG_THREE_WAY_PRIORITY_4: u32 attribute. 6498 * Indicate the Priority 4 profiles. 6499 * The profiles are 8-bit values from enum qca_coex_config_profiles. 6500 * In same priority level, maximum to 4 profiles can be set here. 6501 * NOTE: 6502 * Limitations for QCA_VENDOR_ATTR_COEX_CONFIG_THREE_WAY_PRIORITY_x priority 6503 * arrangement: 6504 * 1: In the same u32 attribute (priority x), the profiles enum values own 6505 * same priority level. 6506 * 2: 0xff is default value if the u8 profile value is not set. 6507 * 3: max to 4 rules/profiles in same priority level. 6508 * 4: max to 4 priority level (priority 1 - priority 4) 6509 * 5: one priority level only supports one scenario from WLAN/BT/ZB, 6510 * hybrid rules not support. 6511 * 6: if WMI_COEX_CONFIG_THREE_WAY_COEX_RESET called, priority x will 6512 * remain blank to reset all parameters. 6513 * For example: 6514 * 6515 * If the attributes as follow: 6516 * priority 1: 6517 * ------------------------------------ 6518 * | 0xff | 0 | 1 | 2 | 6519 * ------------------------------------ 6520 * priority 2: 6521 * ------------------------------------- 6522 * | 0xff | 0xff | 0xff | 32 | 6523 * ------------------------------------- 6524 * priority 3: 6525 * ------------------------------------- 6526 * | 0xff | 0xff | 0xff | 65 | 6527 * ------------------------------------- 6528 * then it means: 6529 * 1: WIFI_STA_DISCOVERY, WIFI_STA_CLASS_3_MGMT and WIFI_STA_CONNECTION 6530 * owns same priority level. 6531 * 2: WIFI_STA_DISCOVERY, WIFI_STA_CLASS_3_MGMT and WIFI_STA_CONNECTION 6532 * has priority over BT_A2DP and ZB_HIGH. 6533 * 3: BT_A2DP has priority over ZB_HIGH. 6534 */ 6535 6536 enum qca_vendor_attr_coex_config_three_way { 6537 QCA_VENDOR_ATTR_COEX_CONFIG_THREE_WAY_INVALID = 0, 6538 QCA_VENDOR_ATTR_COEX_CONFIG_THREE_WAY_CONFIG_TYPE = 1, 6539 QCA_VENDOR_ATTR_COEX_CONFIG_THREE_WAY_PRIORITY_1 = 2, 6540 QCA_VENDOR_ATTR_COEX_CONFIG_THREE_WAY_PRIORITY_2 = 3, 6541 QCA_VENDOR_ATTR_COEX_CONFIG_THREE_WAY_PRIORITY_3 = 4, 6542 QCA_VENDOR_ATTR_COEX_CONFIG_THREE_WAY_PRIORITY_4 = 5, 6543 6544 /* Keep last */ 6545 QCA_VENDOR_ATTR_COEX_CONFIG_THREE_WAY_AFTER_LAST, 6546 QCA_VENDOR_ATTR_COEX_CONFIG_THREE_WAY_MAX = 6547 QCA_VENDOR_ATTR_COEX_CONFIG_THREE_WAY_AFTER_LAST - 1, 6548 }; 6549 6550 /** 6551 * enum qca_wlan_vendor_attr_link_properties - Represent the link properties. 6552 * 6553 * @QCA_WLAN_VENDOR_ATTR_LINK_PROPERTIES_MAC_ADDR: MAC address of the peer 6554 * (STA/AP) for the connected link. 6555 * @QCA_WLAN_VENDOR_ATTR_LINK_PROPERTIES_STA_FLAGS: Attribute containing a 6556 * &struct nl80211_sta_flag_update for the respective connected link. MAC 6557 * address of the peer represented by 6558 * QCA_WLAN_VENDOR_ATTR_LINK_PROPERTIES_MAC_ADDR. 6559 */ 6560 enum qca_wlan_vendor_attr_link_properties { 6561 QCA_WLAN_VENDOR_ATTR_LINK_PROPERTIES_INVALID = 0, 6562 /* 1 - 3 are reserved */ 6563 QCA_WLAN_VENDOR_ATTR_LINK_PROPERTIES_MAC_ADDR = 4, 6564 QCA_WLAN_VENDOR_ATTR_LINK_PROPERTIES_STA_FLAGS = 5, 6565 6566 /* Keep last */ 6567 QCA_VENDOR_ATTR_LINK_PROPERTIES_AFTER_LAST, 6568 QCA_VENDOR_ATTR_LINK_PROPERTIES_MAX = 6569 QCA_VENDOR_ATTR_LINK_PROPERTIES_AFTER_LAST - 1, 6570 }; 6571 6572 /** 6573 * enum qca_vendor_attr_peer_stats_cache_type - Represents peer stats cache type 6574 * This enum defines the valid set of values of peer stats cache types. These 6575 * values are used by attribute 6576 * %QCA_WLAN_VENDOR_ATTR_PEER_STATS_CACHE_TYPE. 6577 * 6578 * @QCA_WLAN_VENDOR_ATTR_PEER_TX_RATE_STATS: Represents peer TX rate statistics 6579 * @QCA_WLAN_VENDOR_ATTR_PEER_RX_RATE_STATS: Represents peer RX rate statistics 6580 * @QCA_WLAN_VENDOR_ATTR_PEER_TX_SOJOURN_STATS: Represents peer TX sojourn 6581 * statistics 6582 */ 6583 enum qca_vendor_attr_peer_stats_cache_type { 6584 QCA_WLAN_VENDOR_ATTR_PEER_STATS_CACHE_TYPE_INVALID = 0, 6585 6586 QCA_WLAN_VENDOR_ATTR_PEER_TX_RATE_STATS, 6587 QCA_WLAN_VENDOR_ATTR_PEER_RX_RATE_STATS, 6588 QCA_WLAN_VENDOR_ATTR_PEER_TX_SOJOURN_STATS, 6589 }; 6590 6591 /** 6592 * enum qca_wlan_vendor_attr_peer_stats_cache_params - This enum defines 6593 * attributes required for QCA_NL80211_VENDOR_SUBCMD_PEER_STATS_CACHE_FLUSH 6594 * Information in these attributes is used to flush peer rate statistics from 6595 * the driver to user application. 6596 * 6597 * @QCA_WLAN_VENDOR_ATTR_PEER_STATS_CACHE_TYPE: Unsigned 32-bit attribute 6598 * Indicate peer statistics cache type. 6599 * The statistics types are 32-bit values from 6600 * enum qca_vendor_attr_peer_stats_cache_type. 6601 * @QCA_WLAN_VENDOR_ATTR_PEER_STATS_CACHE_PEER_MAC: Unsigned 8-bit array 6602 * of size 6 octets, representing the peer MAC address. 6603 * @QCA_WLAN_VENDOR_ATTR_PEER_STATS_CACHE_DATA: Opaque data attribute 6604 * containing buffer of statistics to send to application layer entity. 6605 * @QCA_WLAN_VENDOR_ATTR_PEER_STATS_CACHE_PEER_COOKIE: Unsigned 64-bit attribute 6606 * representing a cookie for peer unique session. 6607 */ 6608 enum qca_wlan_vendor_attr_peer_stats_cache_params { 6609 QCA_WLAN_VENDOR_ATTR_PEER_STATS_INVALID = 0, 6610 6611 QCA_WLAN_VENDOR_ATTR_PEER_STATS_CACHE_TYPE = 1, 6612 QCA_WLAN_VENDOR_ATTR_PEER_STATS_CACHE_PEER_MAC = 2, 6613 QCA_WLAN_VENDOR_ATTR_PEER_STATS_CACHE_DATA = 3, 6614 QCA_WLAN_VENDOR_ATTR_PEER_STATS_CACHE_PEER_COOKIE = 4, 6615 6616 /* Keep last */ 6617 QCA_WLAN_VENDOR_ATTR_PEER_STATS_CACHE_LAST, 6618 QCA_WLAN_VENDOR_ATTR_PEER_STATS_CACHE_MAX = 6619 QCA_WLAN_VENDOR_ATTR_PEER_STATS_CACHE_LAST - 1 6620 }; 6621 6622 /** 6623 * enum qca_mpta_helper_attr_zigbee_state - Current Zigbee state 6624 * This enum defines all the possible states of Zigbee, which can be 6625 * delivered in the QCA_MPTA_HELPER_VENDOR_ATTR_ZIGBEE_STATE attribute. 6626 * 6627 * @ZIGBEE_IDLE: Zigbee in idle state 6628 * @ZIGBEE_FORM_NETWORK: Zigbee forming network 6629 * @ZIGBEE_WAIT_JOIN: Zigbee waiting for joining network 6630 * @ZIGBEE_JOIN: Zigbee joining network 6631 * @ZIGBEE_NETWORK_UP: Zigbee network is up 6632 * @ZIGBEE_HMI: Zigbee in HMI mode 6633 */ 6634 enum qca_mpta_helper_attr_zigbee_state { 6635 ZIGBEE_IDLE = 0, 6636 ZIGBEE_FORM_NETWORK = 1, 6637 ZIGBEE_WAIT_JOIN = 2, 6638 ZIGBEE_JOIN = 3, 6639 ZIGBEE_NETWORK_UP = 4, 6640 ZIGBEE_HMI = 5, 6641 }; 6642 6643 /* 6644 * enum qca_mpta_helper_vendor_attr - Attributes used in vendor sub-command 6645 * QCA_NL80211_VENDOR_SUBCMD_MPTA_HELPER_CONFIG. 6646 */ 6647 enum qca_mpta_helper_vendor_attr { 6648 QCA_MPTA_HELPER_VENDOR_ATTR_INVALID = 0, 6649 /* Optional attribute used to update Zigbee state. 6650 * enum qca_mpta_helper_attr_zigbee_state. 6651 * NLA_U32 attribute. 6652 */ 6653 QCA_MPTA_HELPER_VENDOR_ATTR_ZIGBEE_STATE = 1, 6654 /* Optional attribute used to configure WLAN duration for Shape-OCS 6655 * during interrupt. 6656 * Set in pair with QCA_MPTA_HELPER_VENDOR_ATTR_INT_NON_WLAN_DURATION. 6657 * Value range 0 ~ 300 (ms). 6658 * NLA_U32 attribute. 6659 */ 6660 QCA_MPTA_HELPER_VENDOR_ATTR_INT_WLAN_DURATION = 2, 6661 /* Optional attribute used to configure non-WLAN duration for Shape-OCS 6662 * during interrupt. 6663 * Set in pair with QCA_MPTA_HELPER_VENDOR_ATTR_INT_WLAN_DURATION. 6664 * Value range 0 ~ 300 (ms). 6665 * NLA_U32 attribute. 6666 */ 6667 QCA_MPTA_HELPER_VENDOR_ATTR_INT_NON_WLAN_DURATION = 3, 6668 /* Optional attribute used to configure WLAN duration for Shape-OCS 6669 * monitor period. 6670 * Set in pair with QCA_MPTA_HELPER_VENDOR_ATTR_MON_NON_WLAN_DURATION. 6671 * Value range 0 ~ 300 (ms) 6672 * NLA_U32 attribute 6673 */ 6674 QCA_MPTA_HELPER_VENDOR_ATTR_MON_WLAN_DURATION = 4, 6675 /* Optional attribute used to configure non-WLAN duration for Shape-OCS 6676 * monitor period. 6677 * Set in pair with QCA_MPTA_HELPER_VENDOR_ATTR_MON_WLAN_DURATION. 6678 * Value range 0 ~ 300 (ms) 6679 * NLA_U32 attribute 6680 */ 6681 QCA_MPTA_HELPER_VENDOR_ATTR_MON_NON_WLAN_DURATION = 5, 6682 /* Optional attribute used to configure OCS interrupt duration. 6683 * Set in pair with QCA_MPTA_HELPER_VENDOR_ATTR_MON_OCS_DURATION. 6684 * Value range 1000 ~ 20000 (ms) 6685 * NLA_U32 attribute 6686 */ 6687 QCA_MPTA_HELPER_VENDOR_ATTR_INT_OCS_DURATION = 6, 6688 /* Optional attribute used to configure OCS monitor duration. 6689 * Set in pair with QCA_MPTA_HELPER_VENDOR_ATTR_INT_OCS_DURATION. 6690 * Value range 1000 ~ 20000 (ms) 6691 * NLA_U32 attribute 6692 */ 6693 QCA_MPTA_HELPER_VENDOR_ATTR_MON_OCS_DURATION = 7, 6694 /* Optional attribute used to notify WLAN firmware the current Zigbee 6695 * channel. 6696 * Value range 11 ~ 26 6697 * NLA_U32 attribute 6698 */ 6699 QCA_MPTA_HELPER_VENDOR_ATTR_ZIGBEE_CHAN = 8, 6700 /* Optional attribute used to configure WLAN mute duration. 6701 * Value range 0 ~ 400 (ms) 6702 * NLA_U32 attribute 6703 */ 6704 QCA_MPTA_HELPER_VENDOR_ATTR_WLAN_MUTE_DURATION = 9, 6705 6706 /* keep last */ 6707 QCA_MPTA_HELPER_VENDOR_ATTR_AFTER_LAST, 6708 QCA_MPTA_HELPER_VENDOR_ATTR_MAX = 6709 QCA_MPTA_HELPER_VENDOR_ATTR_AFTER_LAST - 1 6710 }; 6711 6712 #endif /* QCA_VENDOR_H */ 6713