1 /* 2 * Qualcomm Atheros OUI and vendor specific assignments 3 * Copyright (c) 2014-2017, Qualcomm Atheros, Inc. 4 * 5 * This software may be distributed under the terms of the BSD license. 6 * See README for more details. 7 */ 8 9 #ifndef QCA_VENDOR_H 10 #define QCA_VENDOR_H 11 12 /* 13 * This file is a registry of identifier assignments from the Qualcomm Atheros 14 * OUI 00:13:74 for purposes other than MAC address assignment. New identifiers 15 * can be assigned through normal review process for changes to the upstream 16 * hostap.git repository. 17 */ 18 19 #define OUI_QCA 0x001374 20 21 /** 22 * enum qca_radiotap_vendor_ids - QCA radiotap vendor namespace IDs 23 */ 24 enum qca_radiotap_vendor_ids { 25 QCA_RADIOTAP_VID_WLANTEST = 0, 26 }; 27 28 /** 29 * enum qca_nl80211_vendor_subcmds - QCA nl80211 vendor command identifiers 30 * 31 * @QCA_NL80211_VENDOR_SUBCMD_UNSPEC: Reserved value 0 32 * 33 * @QCA_NL80211_VENDOR_SUBCMD_TEST: Test command/event 34 * 35 * @QCA_NL80211_VENDOR_SUBCMD_ROAMING: Set roaming policy for drivers that use 36 * internal BSS-selection. This command uses 37 * @QCA_WLAN_VENDOR_ATTR_ROAMING_POLICY to specify the new roaming policy 38 * for the current connection (i.e., changes policy set by the nl80211 39 * Connect command). @QCA_WLAN_VENDOR_ATTR_MAC_ADDR may optionally be 40 * included to indicate which BSS to use in case roaming is disabled. 41 * 42 * @QCA_NL80211_VENDOR_SUBCMD_AVOID_FREQUENCY: Recommendation of frequency 43 * ranges to avoid to reduce issues due to interference or internal 44 * co-existence information in the driver. The event data structure is 45 * defined in struct qca_avoid_freq_list. 46 * 47 * @QCA_NL80211_VENDOR_SUBCMD_DFS_CAPABILITY: Command to check driver support 48 * for DFS offloading. 49 * 50 * @QCA_NL80211_VENDOR_SUBCMD_NAN: NAN command/event which is used to pass 51 * NAN Request/Response and NAN Indication messages. These messages are 52 * interpreted between the framework and the firmware component. 53 * 54 * @QCA_NL80211_VENDOR_SUBCMD_KEY_MGMT_SET_KEY: Set key operation that can be 55 * used to configure PMK to the driver even when not connected. This can 56 * be used to request offloading of key management operations. Only used 57 * if device supports QCA_WLAN_VENDOR_FEATURE_KEY_MGMT_OFFLOAD. 58 * 59 * @QCA_NL80211_VENDOR_SUBCMD_KEY_MGMT_ROAM_AUTH: An extended version of 60 * NL80211_CMD_ROAM event with optional attributes including information 61 * from offloaded key management operation. Uses 62 * enum qca_wlan_vendor_attr_roam_auth attributes. Only used 63 * if device supports QCA_WLAN_VENDOR_FEATURE_KEY_MGMT_OFFLOAD. 64 * 65 * @QCA_NL80211_VENDOR_SUBCMD_DO_ACS: ACS command/event which is used to 66 * invoke the ACS function in device and pass selected channels to 67 * hostapd. 68 * 69 * @QCA_NL80211_VENDOR_SUBCMD_GET_FEATURES: Command to get the features 70 * supported by the driver. enum qca_wlan_vendor_features defines 71 * the possible features. 72 * 73 * @QCA_NL80211_VENDOR_SUBCMD_DFS_OFFLOAD_CAC_STARTED: Event used by driver, 74 * which supports DFS offloading, to indicate a channel availability check 75 * start. 76 * 77 * @QCA_NL80211_VENDOR_SUBCMD_DFS_OFFLOAD_CAC_FINISHED: Event used by driver, 78 * which supports DFS offloading, to indicate a channel availability check 79 * completion. 80 * 81 * @QCA_NL80211_VENDOR_SUBCMD_DFS_OFFLOAD_CAC_ABORTED: Event used by driver, 82 * which supports DFS offloading, to indicate that the channel availability 83 * check aborted, no change to the channel status. 84 * 85 * @QCA_NL80211_VENDOR_SUBCMD_DFS_OFFLOAD_CAC_NOP_FINISHED: Event used by 86 * driver, which supports DFS offloading, to indicate that the 87 * Non-Occupancy Period for this channel is over, channel becomes usable. 88 * 89 * @QCA_NL80211_VENDOR_SUBCMD_DFS_OFFLOAD_RADAR_DETECTED: Event used by driver, 90 * which supports DFS offloading, to indicate a radar pattern has been 91 * detected. The channel is now unusable. 92 * 93 * @QCA_NL80211_VENDOR_SUBCMD_OCB_SET_CONFIG: Command used to set configuration 94 * for IEEE 802.11 communicating outside the context of a basic service 95 * set, called OCB command. Uses the attributes defines in 96 * enum qca_wlan_vendor_attr_ocb_set_config. 97 * 98 * @QCA_NL80211_VENDOR_SUBCMD_OCB_SET_UTC_TIME: Command used to set OCB 99 * UTC time. Use the attributes defines in 100 * enum qca_wlan_vendor_attr_ocb_set_utc_time. 101 * 102 * @QCA_NL80211_VENDOR_SUBCMD_OCB_START_TIMING_ADVERT: Command used to start 103 * sending OCB timing advert frames. Uses the attributes defines in 104 * enum qca_wlan_vendor_attr_ocb_start_timing_advert. 105 * 106 * @QCA_NL80211_VENDOR_SUBCMD_OCB_STOP_TIMING_ADVERT: Command used to stop 107 * OCB timing advert. Uses the attributes defines in 108 * enum qca_wlan_vendor_attr_ocb_stop_timing_advert. 109 * 110 * @QCA_NL80211_VENDOR_SUBCMD_OCB_GET_TSF_TIMER: Command used to get TSF 111 * timer value. Uses the attributes defines in 112 * enum qca_wlan_vendor_attr_ocb_get_tsf_resp. 113 * 114 * @QCA_NL80211_VENDOR_SUBCMD_P2P_LISTEN_OFFLOAD_START: Command used to 115 * start the P2P Listen offload function in device and pass the listen 116 * channel, period, interval, count, device types, and vendor specific 117 * information elements to the device driver and firmware. 118 * Uses the attributes defines in 119 * enum qca_wlan_vendor_attr_p2p_listen_offload. 120 * 121 * @QCA_NL80211_VENDOR_SUBCMD_P2P_LISTEN_OFFLOAD_STOP: Command/event used to 122 * indicate stop request/response of the P2P Listen offload function in 123 * device. As an event, it indicates either the feature stopped after it 124 * was already running or feature has actually failed to start. Uses the 125 * attributes defines in enum qca_wlan_vendor_attr_p2p_listen_offload. 126 * 127 * @QCA_NL80211_VENDOR_SUBCMD_SAP_CONDITIONAL_CHAN_SWITCH: After AP starts 128 * beaconing, this sub command provides the driver, the frequencies on the 129 * 5 GHz band to check for any radar activity. Driver selects one channel 130 * from this priority list provided through 131 * @QCA_WLAN_VENDOR_ATTR_SAP_CONDITIONAL_CHAN_SWITCH_FREQ_LIST and starts 132 * to check for radar activity on it. If no radar activity is detected 133 * during the channel availability check period, driver internally switches 134 * to the selected frequency of operation. If the frequency is zero, driver 135 * internally selects a channel. The status of this conditional switch is 136 * indicated through an event using the same sub command through 137 * @QCA_WLAN_VENDOR_ATTR_SAP_CONDITIONAL_CHAN_SWITCH_STATUS. Attributes are 138 * listed in qca_wlan_vendor_attr_sap_conditional_chan_switch. 139 * 140 * @QCA_NL80211_VENDOR_SUBCMD_GPIO_CONFIG_COMMAND: Set GPIO pins. This uses the 141 * attributes defined in enum qca_wlan_gpio_attr. 142 * 143 * @QCA_NL80211_VENDOR_SUBCMD_GET_HW_CAPABILITY: Fetch hardware capabilities. 144 * This uses @QCA_WLAN_VENDOR_ATTR_GET_HW_CAPABILITY to indicate which 145 * capabilities are to be fetched and other 146 * enum qca_wlan_vendor_attr_get_hw_capability attributes to return the 147 * requested capabilities. 148 * 149 * @QCA_NL80211_VENDOR_SUBCMD_LL_STATS_EXT: Link layer statistics extension. 150 * enum qca_wlan_vendor_attr_ll_stats_ext attributes are used with this 151 * command and event. 152 * 153 * @QCA_NL80211_VENDOR_SUBCMD_LOC_GET_CAPA: Get capabilities for 154 * indoor location features. Capabilities are reported in 155 * QCA_WLAN_VENDOR_ATTR_LOC_CAPA. 156 * 157 * @QCA_NL80211_VENDOR_SUBCMD_FTM_START_SESSION: Start an FTM 158 * (fine timing measurement) session with one or more peers. 159 * Specify Session cookie in QCA_WLAN_VENDOR_ATTR_FTM_SESSION_COOKIE and 160 * peer information in QCA_WLAN_VENDOR_ATTR_FTM_MEAS_PEERS. 161 * On success, 0 or more QCA_NL80211_VENDOR_SUBCMD_FTM_MEAS_RESULT 162 * events will be reported, followed by 163 * QCA_NL80211_VENDOR_SUBCMD_FTM_SESSION_DONE event to indicate 164 * end of session. 165 * Refer to IEEE P802.11-REVmc/D7.0, 11.24.6 166 * 167 * @QCA_NL80211_VENDOR_SUBCMD_FTM_ABORT_SESSION: Abort a running session. 168 * A QCA_NL80211_VENDOR_SUBCMD_FTM_SESSION_DONE will be reported with 169 * status code indicating session was aborted. 170 * 171 * @QCA_NL80211_VENDOR_SUBCMD_FTM_MEAS_RESULT: Event with measurement 172 * results for one peer. Results are reported in 173 * QCA_WLAN_VENDOR_ATTR_FTM_MEAS_PEER_RESULTS. 174 * 175 * @QCA_NL80211_VENDOR_SUBCMD_FTM_SESSION_DONE: Event triggered when 176 * FTM session is finished, either successfully or aborted by 177 * request. 178 * 179 * @QCA_NL80211_VENDOR_SUBCMD_FTM_CFG_RESPONDER: Configure FTM responder 180 * mode. QCA_WLAN_VENDOR_ATTR_FTM_RESPONDER_ENABLE specifies whether 181 * to enable or disable the responder. LCI/LCR reports can be 182 * configured with QCA_WLAN_VENDOR_ATTR_FTM_LCI and 183 * QCA_WLAN_VENDOR_ATTR_FTM_LCR. Can be called multiple 184 * times to update the LCI/LCR reports. 185 * 186 * @QCA_NL80211_VENDOR_SUBCMD_AOA_MEAS: Perform a standalone AOA (angle of 187 * arrival) measurement with a single peer. Specify peer MAC address in 188 * QCA_WLAN_VENDOR_ATTR_MAC_ADDR and optionally frequency (MHz) in 189 * QCA_WLAN_VENDOR_ATTR_FREQ (if not specified, locate peer in kernel 190 * scan results cache and use the frequency from there). 191 * Also specify measurement type in QCA_WLAN_VENDOR_ATTR_AOA_TYPE. 192 * Measurement result is reported in 193 * QCA_NL80211_VENDOR_SUBCMD_AOA_MEAS_RESULT event. 194 * 195 * @QCA_NL80211_VENDOR_SUBCMD_AOA_ABORT_MEAS: Abort an AOA measurement. Specify 196 * peer MAC address in QCA_WLAN_VENDOR_ATTR_MAC_ADDR. 197 * 198 * @QCA_NL80211_VENDOR_SUBCMD_AOA_MEAS_RESULT: Event that reports 199 * the AOA measurement result. 200 * Peer MAC address reported in QCA_WLAN_VENDOR_ATTR_MAC_ADDR. 201 * success/failure status is reported in 202 * QCA_WLAN_VENDOR_ATTR_LOC_SESSION_STATUS. 203 * Measurement data is reported in QCA_WLAN_VENDOR_ATTR_AOA_MEAS_RESULT. 204 * The antenna array(s) used in the measurement are reported in 205 * QCA_WLAN_VENDOR_ATTR_LOC_ANTENNA_ARRAY_MASK. 206 * 207 * @QCA_NL80211_VENDOR_SUBCMD_ENCRYPTION_TEST: Encrypt/decrypt the given 208 * data as per the given parameters. 209 * 210 * @QCA_NL80211_VENDOR_SUBCMD_GET_CHAIN_RSSI: Get antenna RSSI value for a 211 * specific chain. 212 * 213 * @QCA_NL80211_VENDOR_SUBCMD_DMG_RF_GET_SECTOR_CFG: Get low level 214 * configuration for a DMG RF sector. Specify sector index in 215 * QCA_WLAN_VENDOR_ATTR_DMG_RF_SECTOR_INDEX, sector type in 216 * QCA_WLAN_VENDOR_ATTR_DMG_RF_SECTOR_TYPE and RF modules 217 * to return sector information for in 218 * QCA_WLAN_VENDOR_ATTR_DMG_RF_MODULE_MASK. Returns sector configuration 219 * in QCA_WLAN_VENDOR_ATTR_DMG_RF_SECTOR_CFG. Also return the 220 * exact time where information was captured in 221 * QCA_WLAN_VENDOR_ATTR_TSF. 222 * 223 * @QCA_NL80211_VENDOR_SUBCMD_DMG_RF_SET_SECTOR_CFG: Set low level 224 * configuration for a DMG RF sector. Specify sector index in 225 * QCA_WLAN_VENDOR_ATTR_DMG_RF_SECTOR_INDEX, sector type in 226 * QCA_WLAN_VENDOR_ATTR_DMG_RF_SECTOR_TYPE and sector configuration 227 * for one or more DMG RF modules in 228 * QCA_WLAN_VENDOR_ATTR_DMG_RF_SECTOR_CFG. 229 * 230 * @QCA_NL80211_VENDOR_SUBCMD_DMG_RF_GET_SELECTED_SECTOR: Get selected 231 * DMG RF sector for a station. This is the sector that the HW 232 * will use to communicate with the station. Specify the MAC address 233 * of associated station/AP/PCP in QCA_WLAN_VENDOR_ATTR_MAC_ADDR (not 234 * needed for unassociated station). Specify sector type to return in 235 * QCA_WLAN_VENDOR_ATTR_DMG_RF_SECTOR_TYPE. Returns the selected 236 * sector index in QCA_WLAN_VENDOR_ATTR_DMG_RF_SECTOR_INDEX. 237 * Also return the exact time where the information was captured 238 * in QCA_WLAN_VENDOR_ATTR_TSF. 239 * 240 * @QCA_NL80211_VENDOR_SUBCMD_DMG_RF_SET_SELECTED_SECTOR: Set the 241 * selected DMG RF sector for a station. This is the sector that 242 * the HW will use to communicate with the station. 243 * Specify the MAC address of associated station/AP/PCP in 244 * QCA_WLAN_VENDOR_ATTR_MAC_ADDR, the sector type to select in 245 * QCA_WLAN_VENDOR_ATTR_DMG_RF_SECTOR_TYPE and the sector index 246 * in QCA_WLAN_VENDOR_ATTR_DMG_RF_SECTOR_INDEX. 247 * The selected sector will be locked such that it will not be 248 * modified like it normally does (for example when station 249 * moves around). To unlock the selected sector for a station 250 * pass the special value 0xFFFF in the sector index. To unlock 251 * all connected stations also pass a broadcast MAC address. 252 * 253 * @QCA_NL80211_VENDOR_SUBCMD_CONFIGURE_TDLS: Configure the TDLS behavior 254 * in the host driver. The different TDLS configurations are defined 255 * by the attributes in enum qca_wlan_vendor_attr_tdls_configuration. 256 * 257 * @QCA_NL80211_VENDOR_SUBCMD_GET_HE_CAPABILITIES: Query device IEEE 802.11ax HE 258 * capabilities. The response uses the attributes defined in 259 * enum qca_wlan_vendor_attr_get_he_capabilities. 260 * 261 * @QCA_NL80211_VENDOR_SUBCMD_ABORT_SCAN: Abort an ongoing vendor scan that was 262 * started with QCA_NL80211_VENDOR_SUBCMD_TRIGGER_SCAN. This command 263 * carries the scan cookie of the corresponding scan request. The scan 264 * cookie is represented by QCA_WLAN_VENDOR_ATTR_SCAN_COOKIE. 265 * 266 * @QCA_NL80211_VENDOR_SUBCMD_SET_SAR_LIMITS: Set the Specific 267 * Absorption Rate (SAR) power limits. A critical regulation for 268 * FCC compliance, OEMs require methods to set SAR limits on TX 269 * power of WLAN/WWAN. enum qca_vendor_attr_sar_limits 270 * attributes are used with this command. 271 * 272 * @QCA_NL80211_VENDOR_SUBCMD_EXTERNAL_ACS: This command/event is used by the 273 * host driver for offloading the implementation of Auto Channel Selection 274 * (ACS) to an external user space entity. This interface is used as the 275 * event from the host driver to the user space entity and also as the 276 * request from the user space entity to the host driver. The event from 277 * the host driver is used by the user space entity as an indication to 278 * start the ACS functionality. The attributes used by this event are 279 * represented by the enum qca_wlan_vendor_attr_external_acs_event. 280 * User space entity uses the same interface to inform the host driver with 281 * selected channels after the ACS operation using the attributes defined 282 * by enum qca_wlan_vendor_attr_external_acs_channels. 283 * 284 * @QCA_NL80211_VENDOR_SUBCMD_CHIP_PWRSAVE_FAILURE: Vendor event carrying the 285 * requisite information leading to a power save failure. The information 286 * carried as part of this event is represented by the 287 * enum qca_attr_chip_power_save_failure attributes. 288 * 289 * @QCA_NL80211_VENDOR_SUBCMD_NUD_STATS_SET: Start/Stop the NUD statistics 290 * collection. Uses attributes defined in enum qca_attr_nud_stats_set. 291 * 292 * @QCA_NL80211_VENDOR_SUBCMD_NUD_STATS_GET: Get the NUD statistics. These 293 * statistics are represented by the enum qca_attr_nud_stats_get 294 * attributes. 295 * 296 * @QCA_NL80211_VENDOR_SUBCMD_FETCH_BSS_TRANSITION_STATUS: Sub-command to fetch 297 * the BSS transition status, whether accept or reject, for a list of 298 * candidate BSSIDs provided by the userspace. This uses the vendor 299 * attributes QCA_WLAN_VENDOR_ATTR_BTM_MBO_TRANSITION_REASON and 300 * QCA_WLAN_VENDOR_ATTR_BTM_CANDIDATE_INFO. The userspace shall specify 301 * the attributes QCA_WLAN_VENDOR_ATTR_BTM_MBO_TRANSITION_REASON and an 302 * array of QCA_WLAN_VENDOR_ATTR_BTM_CANDIDATE_INFO_BSSID nested in 303 * QCA_WLAN_VENDOR_ATTR_BTM_CANDIDATE_INFO in the request. In the response 304 * the driver shall specify array of 305 * QCA_WLAN_VENDOR_ATTR_BTM_CANDIDATE_INFO_BSSID and 306 * QCA_WLAN_VENDOR_ATTR_BTM_CANDIDATE_INFO_STATUS pairs nested in 307 * QCA_WLAN_VENDOR_ATTR_BTM_CANDIDATE_INFO. 308 * 309 * @QCA_NL80211_VENDOR_SUBCMD_SET_TRACE_LEVEL: Set the trace level for a 310 * specific QCA module. The trace levels are represented by 311 * enum qca_attr_trace_level attributes. 312 * 313 * @QCA_NL80211_VENDOR_SUBCMD_BRP_SET_ANT_LIMIT: Set the Beam Refinement 314 * Protocol antenna limit in different modes. See enum 315 * qca_wlan_vendor_attr_brp_ant_limit_mode. 316 * 317 * @QCA_NL80211_VENDOR_SUBCMD_SPECTRAL_SCAN_START: Start spectral scan. The scan 318 * parameters are specified by enum qca_wlan_vendor_attr_spectral_scan. 319 * This returns a cookie (%QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_COOKIE) 320 * identifying the operation in success case. 321 * 322 * @QCA_NL80211_VENDOR_SUBCMD_SPECTRAL_SCAN_STOP: Stop spectral scan. This uses 323 * a cookie (%QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_COOKIE) from 324 * @QCA_NL80211_VENDOR_SUBCMD_SPECTRAL_SCAN_START to identify the scan to 325 * be stopped. 326 * 327 * @QCA_NL80211_VENDOR_SUBCMD_ACTIVE_TOS: Set the active Type Of Service on the 328 * specific interface. This can be used to modify some of the low level 329 * scan parameters (off channel dwell time, home channel time) in the 330 * driver/firmware. These parameters are maintained within the host driver. 331 * This command is valid only when the interface is in the connected state. 332 * These scan parameters shall be reset by the driver/firmware once 333 * disconnected. The attributes used with this command are defined in 334 * enum qca_wlan_vendor_attr_active_tos. 335 * 336 * @QCA_NL80211_VENDOR_SUBCMD_HANG: Event indicating to the user space that the 337 * driver has detected an internal failure. This event carries the 338 * information indicating the reason that triggered this detection. The 339 * attributes for this command are defined in 340 * enum qca_wlan_vendor_attr_hang. 341 */ 342 enum qca_nl80211_vendor_subcmds { 343 QCA_NL80211_VENDOR_SUBCMD_UNSPEC = 0, 344 QCA_NL80211_VENDOR_SUBCMD_TEST = 1, 345 /* subcmds 2..8 not yet allocated */ 346 QCA_NL80211_VENDOR_SUBCMD_ROAMING = 9, 347 QCA_NL80211_VENDOR_SUBCMD_AVOID_FREQUENCY = 10, 348 QCA_NL80211_VENDOR_SUBCMD_DFS_CAPABILITY = 11, 349 QCA_NL80211_VENDOR_SUBCMD_NAN = 12, 350 QCA_NL80211_VENDOR_SUBCMD_STATS_EXT = 13, 351 QCA_NL80211_VENDOR_SUBCMD_LL_STATS_SET = 14, 352 QCA_NL80211_VENDOR_SUBCMD_LL_STATS_GET = 15, 353 QCA_NL80211_VENDOR_SUBCMD_LL_STATS_CLR = 16, 354 QCA_NL80211_VENDOR_SUBCMD_LL_STATS_RADIO_RESULTS = 17, 355 QCA_NL80211_VENDOR_SUBCMD_LL_STATS_IFACE_RESULTS = 18, 356 QCA_NL80211_VENDOR_SUBCMD_LL_STATS_PEERS_RESULTS = 19, 357 QCA_NL80211_VENDOR_SUBCMD_GSCAN_START = 20, 358 QCA_NL80211_VENDOR_SUBCMD_GSCAN_STOP = 21, 359 QCA_NL80211_VENDOR_SUBCMD_GSCAN_GET_VALID_CHANNELS = 22, 360 QCA_NL80211_VENDOR_SUBCMD_GSCAN_GET_CAPABILITIES = 23, 361 QCA_NL80211_VENDOR_SUBCMD_GSCAN_GET_CACHED_RESULTS = 24, 362 QCA_NL80211_VENDOR_SUBCMD_GSCAN_SCAN_RESULTS_AVAILABLE = 25, 363 QCA_NL80211_VENDOR_SUBCMD_GSCAN_FULL_SCAN_RESULT = 26, 364 QCA_NL80211_VENDOR_SUBCMD_GSCAN_SCAN_EVENT = 27, 365 QCA_NL80211_VENDOR_SUBCMD_GSCAN_HOTLIST_AP_FOUND = 28, 366 QCA_NL80211_VENDOR_SUBCMD_GSCAN_SET_BSSID_HOTLIST = 29, 367 QCA_NL80211_VENDOR_SUBCMD_GSCAN_RESET_BSSID_HOTLIST = 30, 368 QCA_NL80211_VENDOR_SUBCMD_GSCAN_SIGNIFICANT_CHANGE = 31, 369 QCA_NL80211_VENDOR_SUBCMD_GSCAN_SET_SIGNIFICANT_CHANGE = 32, 370 QCA_NL80211_VENDOR_SUBCMD_GSCAN_RESET_SIGNIFICANT_CHANGE = 33, 371 QCA_NL80211_VENDOR_SUBCMD_TDLS_ENABLE = 34, 372 QCA_NL80211_VENDOR_SUBCMD_TDLS_DISABLE = 35, 373 QCA_NL80211_VENDOR_SUBCMD_TDLS_GET_STATUS = 36, 374 QCA_NL80211_VENDOR_SUBCMD_TDLS_STATE = 37, 375 QCA_NL80211_VENDOR_SUBCMD_GET_SUPPORTED_FEATURES = 38, 376 QCA_NL80211_VENDOR_SUBCMD_SCANNING_MAC_OUI = 39, 377 QCA_NL80211_VENDOR_SUBCMD_NO_DFS_FLAG = 40, 378 QCA_NL80211_VENDOR_SUBCMD_GSCAN_HOTLIST_AP_LOST = 41, 379 QCA_NL80211_VENDOR_SUBCMD_GET_CONCURRENCY_MATRIX = 42, 380 /* 43..49 - reserved for QCA */ 381 QCA_NL80211_VENDOR_SUBCMD_KEY_MGMT_SET_KEY = 50, 382 QCA_NL80211_VENDOR_SUBCMD_KEY_MGMT_ROAM_AUTH = 51, 383 QCA_NL80211_VENDOR_SUBCMD_APFIND = 52, 384 /* 53 - reserved - was used by QCA, but not in use anymore */ 385 QCA_NL80211_VENDOR_SUBCMD_DO_ACS = 54, 386 QCA_NL80211_VENDOR_SUBCMD_GET_FEATURES = 55, 387 QCA_NL80211_VENDOR_SUBCMD_DFS_OFFLOAD_CAC_STARTED = 56, 388 QCA_NL80211_VENDOR_SUBCMD_DFS_OFFLOAD_CAC_FINISHED = 57, 389 QCA_NL80211_VENDOR_SUBCMD_DFS_OFFLOAD_CAC_ABORTED = 58, 390 QCA_NL80211_VENDOR_SUBCMD_DFS_OFFLOAD_CAC_NOP_FINISHED = 59, 391 QCA_NL80211_VENDOR_SUBCMD_DFS_OFFLOAD_RADAR_DETECTED = 60, 392 QCA_NL80211_VENDOR_SUBCMD_GET_WIFI_INFO = 61, 393 QCA_NL80211_VENDOR_SUBCMD_WIFI_LOGGER_START = 62, 394 QCA_NL80211_VENDOR_SUBCMD_WIFI_LOGGER_MEMORY_DUMP = 63, 395 QCA_NL80211_VENDOR_SUBCMD_ROAM = 64, 396 QCA_NL80211_VENDOR_SUBCMD_GSCAN_SET_SSID_HOTLIST = 65, 397 QCA_NL80211_VENDOR_SUBCMD_GSCAN_RESET_SSID_HOTLIST = 66, 398 QCA_NL80211_VENDOR_SUBCMD_GSCAN_HOTLIST_SSID_FOUND = 67, 399 QCA_NL80211_VENDOR_SUBCMD_GSCAN_HOTLIST_SSID_LOST = 68, 400 QCA_NL80211_VENDOR_SUBCMD_PNO_SET_LIST = 69, 401 QCA_NL80211_VENDOR_SUBCMD_PNO_SET_PASSPOINT_LIST = 70, 402 QCA_NL80211_VENDOR_SUBCMD_PNO_RESET_PASSPOINT_LIST = 71, 403 QCA_NL80211_VENDOR_SUBCMD_PNO_NETWORK_FOUND = 72, 404 QCA_NL80211_VENDOR_SUBCMD_PNO_PASSPOINT_NETWORK_FOUND = 73, 405 /* Wi-Fi configuration subcommands */ 406 QCA_NL80211_VENDOR_SUBCMD_SET_WIFI_CONFIGURATION = 74, 407 QCA_NL80211_VENDOR_SUBCMD_GET_WIFI_CONFIGURATION = 75, 408 /* 76-90 - reserved for QCA */ 409 QCA_NL80211_VENDOR_SUBCMD_DATA_OFFLOAD = 91, 410 QCA_NL80211_VENDOR_SUBCMD_OCB_SET_CONFIG = 92, 411 QCA_NL80211_VENDOR_SUBCMD_OCB_SET_UTC_TIME = 93, 412 QCA_NL80211_VENDOR_SUBCMD_OCB_START_TIMING_ADVERT = 94, 413 QCA_NL80211_VENDOR_SUBCMD_OCB_STOP_TIMING_ADVERT = 95, 414 QCA_NL80211_VENDOR_SUBCMD_OCB_GET_TSF_TIMER = 96, 415 QCA_NL80211_VENDOR_SUBCMD_DCC_GET_STATS = 97, 416 QCA_NL80211_VENDOR_SUBCMD_DCC_CLEAR_STATS = 98, 417 QCA_NL80211_VENDOR_SUBCMD_DCC_UPDATE_NDL = 99, 418 QCA_NL80211_VENDOR_SUBCMD_DCC_STATS_EVENT = 100, 419 QCA_NL80211_VENDOR_SUBCMD_LINK_PROPERTIES = 101, 420 QCA_NL80211_VENDOR_SUBCMD_GW_PARAM_CONFIG = 102, 421 QCA_NL80211_VENDOR_SUBCMD_GET_PREFERRED_FREQ_LIST = 103, 422 QCA_NL80211_VENDOR_SUBCMD_SET_PROBABLE_OPER_CHANNEL = 104, 423 QCA_NL80211_VENDOR_SUBCMD_SETBAND = 105, 424 QCA_NL80211_VENDOR_SUBCMD_TRIGGER_SCAN = 106, 425 QCA_NL80211_VENDOR_SUBCMD_SCAN_DONE = 107, 426 QCA_NL80211_VENDOR_SUBCMD_OTA_TEST = 108, 427 QCA_NL80211_VENDOR_SUBCMD_SET_TXPOWER_SCALE = 109, 428 /* 110..114 - reserved for QCA */ 429 QCA_NL80211_VENDOR_SUBCMD_SET_TXPOWER_DECR_DB = 115, 430 /* 116..117 - reserved for QCA */ 431 QCA_NL80211_VENDOR_SUBCMD_SET_SAP_CONFIG = 118, 432 QCA_NL80211_VENDOR_SUBCMD_TSF = 119, 433 QCA_NL80211_VENDOR_SUBCMD_WISA = 120, 434 /* 121 - reserved for QCA */ 435 QCA_NL80211_VENDOR_SUBCMD_P2P_LISTEN_OFFLOAD_START = 122, 436 QCA_NL80211_VENDOR_SUBCMD_P2P_LISTEN_OFFLOAD_STOP = 123, 437 QCA_NL80211_VENDOR_SUBCMD_SAP_CONDITIONAL_CHAN_SWITCH = 124, 438 QCA_NL80211_VENDOR_SUBCMD_GPIO_CONFIG_COMMAND = 125, 439 QCA_NL80211_VENDOR_SUBCMD_GET_HW_CAPABILITY = 126, 440 QCA_NL80211_VENDOR_SUBCMD_LL_STATS_EXT = 127, 441 /* FTM/indoor location subcommands */ 442 QCA_NL80211_VENDOR_SUBCMD_LOC_GET_CAPA = 128, 443 QCA_NL80211_VENDOR_SUBCMD_FTM_START_SESSION = 129, 444 QCA_NL80211_VENDOR_SUBCMD_FTM_ABORT_SESSION = 130, 445 QCA_NL80211_VENDOR_SUBCMD_FTM_MEAS_RESULT = 131, 446 QCA_NL80211_VENDOR_SUBCMD_FTM_SESSION_DONE = 132, 447 QCA_NL80211_VENDOR_SUBCMD_FTM_CFG_RESPONDER = 133, 448 QCA_NL80211_VENDOR_SUBCMD_AOA_MEAS = 134, 449 QCA_NL80211_VENDOR_SUBCMD_AOA_ABORT_MEAS = 135, 450 QCA_NL80211_VENDOR_SUBCMD_AOA_MEAS_RESULT = 136, 451 QCA_NL80211_VENDOR_SUBCMD_ENCRYPTION_TEST = 137, 452 QCA_NL80211_VENDOR_SUBCMD_GET_CHAIN_RSSI = 138, 453 /* DMG low level RF sector operations */ 454 QCA_NL80211_VENDOR_SUBCMD_DMG_RF_GET_SECTOR_CFG = 139, 455 QCA_NL80211_VENDOR_SUBCMD_DMG_RF_SET_SECTOR_CFG = 140, 456 QCA_NL80211_VENDOR_SUBCMD_DMG_RF_GET_SELECTED_SECTOR = 141, 457 QCA_NL80211_VENDOR_SUBCMD_DMG_RF_SET_SELECTED_SECTOR = 142, 458 QCA_NL80211_VENDOR_SUBCMD_CONFIGURE_TDLS = 143, 459 QCA_NL80211_VENDOR_SUBCMD_GET_HE_CAPABILITIES = 144, 460 QCA_NL80211_VENDOR_SUBCMD_ABORT_SCAN = 145, 461 QCA_NL80211_VENDOR_SUBCMD_SET_SAR_LIMITS = 146, 462 QCA_NL80211_VENDOR_SUBCMD_EXTERNAL_ACS = 147, 463 QCA_NL80211_VENDOR_SUBCMD_CHIP_PWRSAVE_FAILURE = 148, 464 QCA_NL80211_VENDOR_SUBCMD_NUD_STATS_SET = 149, 465 QCA_NL80211_VENDOR_SUBCMD_NUD_STATS_GET = 150, 466 QCA_NL80211_VENDOR_SUBCMD_FETCH_BSS_TRANSITION_STATUS = 151, 467 QCA_NL80211_VENDOR_SUBCMD_SET_TRACE_LEVEL = 152, 468 QCA_NL80211_VENDOR_SUBCMD_BRP_SET_ANT_LIMIT = 153, 469 QCA_NL80211_VENDOR_SUBCMD_SPECTRAL_SCAN_START = 154, 470 QCA_NL80211_VENDOR_SUBCMD_SPECTRAL_SCAN_STOP = 155, 471 QCA_NL80211_VENDOR_SUBCMD_ACTIVE_TOS = 156, 472 QCA_NL80211_VENDOR_SUBCMD_HANG = 157, 473 }; 474 475 476 enum qca_wlan_vendor_attr { 477 QCA_WLAN_VENDOR_ATTR_INVALID = 0, 478 /* used by QCA_NL80211_VENDOR_SUBCMD_DFS_CAPABILITY */ 479 QCA_WLAN_VENDOR_ATTR_DFS = 1, 480 /* used by QCA_NL80211_VENDOR_SUBCMD_NAN */ 481 QCA_WLAN_VENDOR_ATTR_NAN = 2, 482 /* used by QCA_NL80211_VENDOR_SUBCMD_STATS_EXT */ 483 QCA_WLAN_VENDOR_ATTR_STATS_EXT = 3, 484 /* used by QCA_NL80211_VENDOR_SUBCMD_STATS_EXT */ 485 QCA_WLAN_VENDOR_ATTR_IFINDEX = 4, 486 /* used by QCA_NL80211_VENDOR_SUBCMD_ROAMING, u32 with values defined 487 * by enum qca_roaming_policy. */ 488 QCA_WLAN_VENDOR_ATTR_ROAMING_POLICY = 5, 489 QCA_WLAN_VENDOR_ATTR_MAC_ADDR = 6, 490 /* used by QCA_NL80211_VENDOR_SUBCMD_GET_FEATURES */ 491 QCA_WLAN_VENDOR_ATTR_FEATURE_FLAGS = 7, 492 QCA_WLAN_VENDOR_ATTR_TEST = 8, 493 /* used by QCA_NL80211_VENDOR_SUBCMD_GET_FEATURES */ 494 /* Unsigned 32-bit value. */ 495 QCA_WLAN_VENDOR_ATTR_CONCURRENCY_CAPA = 9, 496 /* Unsigned 32-bit value */ 497 QCA_WLAN_VENDOR_ATTR_MAX_CONCURRENT_CHANNELS_2_4_BAND = 10, 498 /* Unsigned 32-bit value */ 499 QCA_WLAN_VENDOR_ATTR_MAX_CONCURRENT_CHANNELS_5_0_BAND = 11, 500 /* Unsigned 32-bit value from enum qca_set_band. */ 501 QCA_WLAN_VENDOR_ATTR_SETBAND_VALUE = 12, 502 /* Dummy (NOP) attribute for 64 bit padding */ 503 QCA_WLAN_VENDOR_ATTR_PAD = 13, 504 /* Unique FTM session cookie (Unsigned 64 bit). Specified in 505 * QCA_NL80211_VENDOR_SUBCMD_FTM_START_SESSION. Reported in 506 * the session in QCA_NL80211_VENDOR_SUBCMD_FTM_MEAS_RESULT and 507 * QCA_NL80211_VENDOR_SUBCMD_FTM_SESSION_DONE. 508 */ 509 QCA_WLAN_VENDOR_ATTR_FTM_SESSION_COOKIE = 14, 510 /* Indoor location capabilities, returned by 511 * QCA_NL80211_VENDOR_SUBCMD_LOC_GET_CAPA. 512 * see enum qca_wlan_vendor_attr_loc_capa. 513 */ 514 QCA_WLAN_VENDOR_ATTR_LOC_CAPA = 15, 515 /* Array of nested attributes containing information about each peer 516 * in FTM measurement session. See enum qca_wlan_vendor_attr_peer_info 517 * for supported attributes for each peer. 518 */ 519 QCA_WLAN_VENDOR_ATTR_FTM_MEAS_PEERS = 16, 520 /* Array of nested attributes containing measurement results for 521 * one or more peers, reported by the 522 * QCA_NL80211_VENDOR_SUBCMD_FTM_MEAS_RESULT event. 523 * See enum qca_wlan_vendor_attr_peer_result for list of supported 524 * attributes. 525 */ 526 QCA_WLAN_VENDOR_ATTR_FTM_MEAS_PEER_RESULTS = 17, 527 /* Flag attribute for enabling or disabling responder functionality. */ 528 QCA_WLAN_VENDOR_ATTR_FTM_RESPONDER_ENABLE = 18, 529 /* Used in the QCA_NL80211_VENDOR_SUBCMD_FTM_CFG_RESPONDER 530 * command to specify the LCI report that will be sent by 531 * the responder during a measurement exchange. The format is 532 * defined in IEEE P802.11-REVmc/D7.0, 9.4.2.22.10. 533 */ 534 QCA_WLAN_VENDOR_ATTR_FTM_LCI = 19, 535 /* Used in the QCA_NL80211_VENDOR_SUBCMD_FTM_CFG_RESPONDER 536 * command to specify the location civic report that will 537 * be sent by the responder during a measurement exchange. 538 * The format is defined in IEEE P802.11-REVmc/D7.0, 9.4.2.22.13. 539 */ 540 QCA_WLAN_VENDOR_ATTR_FTM_LCR = 20, 541 /* Session/measurement completion status code, 542 * reported in QCA_NL80211_VENDOR_SUBCMD_FTM_SESSION_DONE and 543 * QCA_NL80211_VENDOR_SUBCMD_AOA_MEAS_RESULT 544 * see enum qca_vendor_attr_loc_session_status. 545 */ 546 QCA_WLAN_VENDOR_ATTR_LOC_SESSION_STATUS = 21, 547 /* Initial dialog token used by responder (0 if not specified), 548 * unsigned 8 bit value. 549 */ 550 QCA_WLAN_VENDOR_ATTR_FTM_INITIAL_TOKEN = 22, 551 /* AOA measurement type. Requested in QCA_NL80211_VENDOR_SUBCMD_AOA_MEAS 552 * and optionally in QCA_NL80211_VENDOR_SUBCMD_FTM_START_SESSION if 553 * AOA measurements are needed as part of an FTM session. 554 * Reported by QCA_NL80211_VENDOR_SUBCMD_AOA_MEAS_RESULT. See 555 * enum qca_wlan_vendor_attr_aoa_type. 556 */ 557 QCA_WLAN_VENDOR_ATTR_AOA_TYPE = 23, 558 /* A bit mask (unsigned 32 bit value) of antenna arrays used 559 * by indoor location measurements. Refers to the antenna 560 * arrays described by QCA_VENDOR_ATTR_LOC_CAPA_ANTENNA_ARRAYS. 561 */ 562 QCA_WLAN_VENDOR_ATTR_LOC_ANTENNA_ARRAY_MASK = 24, 563 /* AOA measurement data. Its contents depends on the AOA measurement 564 * type and antenna array mask: 565 * QCA_WLAN_VENDOR_ATTR_AOA_TYPE_TOP_CIR_PHASE: array of U16 values, 566 * phase of the strongest CIR path for each antenna in the measured 567 * array(s). 568 * QCA_WLAN_VENDOR_ATTR_AOA_TYPE_TOP_CIR_PHASE_AMP: array of 2 U16 569 * values, phase and amplitude of the strongest CIR path for each 570 * antenna in the measured array(s). 571 */ 572 QCA_WLAN_VENDOR_ATTR_AOA_MEAS_RESULT = 25, 573 /* Used in QCA_NL80211_VENDOR_SUBCMD_GET_CHAIN_RSSI command 574 * to specify the chain number (unsigned 32 bit value) to inquire 575 * the corresponding antenna RSSI value */ 576 QCA_WLAN_VENDOR_ATTR_CHAIN_INDEX = 26, 577 /* Used in QCA_NL80211_VENDOR_SUBCMD_GET_CHAIN_RSSI command 578 * to report the specific antenna RSSI value (unsigned 32 bit value) */ 579 QCA_WLAN_VENDOR_ATTR_CHAIN_RSSI = 27, 580 /* Frequency in MHz, various uses. Unsigned 32 bit value */ 581 QCA_WLAN_VENDOR_ATTR_FREQ = 28, 582 /* TSF timer value, unsigned 64 bit value. 583 * May be returned by various commands. 584 */ 585 QCA_WLAN_VENDOR_ATTR_TSF = 29, 586 /* DMG RF sector index, unsigned 16 bit number. Valid values are 587 * 0..127 for sector indices or 65535 as special value used to 588 * unlock sector selection in 589 * QCA_NL80211_VENDOR_SUBCMD_DMG_RF_SET_SELECTED_SECTOR. 590 */ 591 QCA_WLAN_VENDOR_ATTR_DMG_RF_SECTOR_INDEX = 30, 592 /* DMG RF sector type, unsigned 8 bit value. One of the values 593 * in enum qca_wlan_vendor_attr_dmg_rf_sector_type. 594 */ 595 QCA_WLAN_VENDOR_ATTR_DMG_RF_SECTOR_TYPE = 31, 596 /* Bitmask of DMG RF modules for which information is requested. Each 597 * bit corresponds to an RF module with the same index as the bit 598 * number. Unsigned 32 bit number but only low 8 bits can be set since 599 * all DMG chips currently have up to 8 RF modules. 600 */ 601 QCA_WLAN_VENDOR_ATTR_DMG_RF_MODULE_MASK = 32, 602 /* Array of nested attributes where each entry is DMG RF sector 603 * configuration for a single RF module. 604 * Attributes for each entry are taken from enum 605 * qca_wlan_vendor_attr_dmg_rf_sector_cfg. 606 * Specified in QCA_NL80211_VENDOR_SUBCMD_DMG_RF_SET_SECTOR_CFG 607 * and returned by QCA_NL80211_VENDOR_SUBCMD_DMG_RF_GET_SECTOR_CFG. 608 */ 609 QCA_WLAN_VENDOR_ATTR_DMG_RF_SECTOR_CFG = 33, 610 /* Used in QCA_NL80211_VENDOR_SUBCMD_STATS_EXT command 611 * to report frame aggregation statistics to userspace. 612 */ 613 QCA_WLAN_VENDOR_ATTR_RX_AGGREGATION_STATS_HOLES_NUM = 34, 614 QCA_WLAN_VENDOR_ATTR_RX_AGGREGATION_STATS_HOLES_INFO = 35, 615 /* Unsigned 8-bit value representing MBO transition reason code as 616 * provided by the AP used by subcommand 617 * QCA_NL80211_VENDOR_SUBCMD_FETCH_BSS_TRANSITION_STATUS. This is 618 * specified by the userspace in the request to the driver. 619 */ 620 QCA_WLAN_VENDOR_ATTR_BTM_MBO_TRANSITION_REASON = 36, 621 /* Array of nested attributes, BSSID and status code, used by subcommand 622 * QCA_NL80211_VENDOR_SUBCMD_FETCH_BSS_TRANSITION_STATUS, where each 623 * entry is taken from enum qca_wlan_vendor_attr_btm_candidate_info. 624 * The userspace space specifies the list/array of candidate BSSIDs in 625 * the order of preference in the request. The driver specifies the 626 * status code, for each BSSID in the list, in the response. The 627 * acceptable candidates are listed in the order preferred by the 628 * driver. 629 */ 630 QCA_WLAN_VENDOR_ATTR_BTM_CANDIDATE_INFO = 37, 631 /* Used in QCA_NL80211_VENDOR_SUBCMD_BRP_SET_ANT_LIMIT command 632 * See enum qca_wlan_vendor_attr_brp_ant_limit_mode. 633 */ 634 QCA_WLAN_VENDOR_ATTR_BRP_ANT_LIMIT_MODE = 38, 635 /* Used in QCA_NL80211_VENDOR_SUBCMD_BRP_SET_ANT_LIMIT command 636 * to define the number of antennas to use for BRP. 637 * different purpose in each ANT_LIMIT_MODE: 638 * DISABLE - ignored 639 * EFFECTIVE - upper limit to number of antennas to be used 640 * FORCE - exact number of antennas to be used 641 * unsigned 8 bit value 642 */ 643 QCA_WLAN_VENDOR_ATTR_BRP_ANT_NUM_LIMIT = 39, 644 /* Used in QCA_NL80211_VENDOR_SUBCMD_GET_CHAIN_RSSI command 645 * to report the corresponding antenna index to the chain RSSI value */ 646 QCA_WLAN_VENDOR_ATTR_ANTENNA_INFO = 40, 647 648 /* keep last */ 649 QCA_WLAN_VENDOR_ATTR_AFTER_LAST, 650 QCA_WLAN_VENDOR_ATTR_MAX = QCA_WLAN_VENDOR_ATTR_AFTER_LAST - 1, 651 }; 652 653 654 enum qca_roaming_policy { 655 QCA_ROAMING_NOT_ALLOWED, 656 QCA_ROAMING_ALLOWED_WITHIN_ESS, 657 }; 658 659 enum qca_wlan_vendor_attr_roam_auth { 660 QCA_WLAN_VENDOR_ATTR_ROAM_AUTH_INVALID = 0, 661 QCA_WLAN_VENDOR_ATTR_ROAM_AUTH_BSSID, 662 QCA_WLAN_VENDOR_ATTR_ROAM_AUTH_REQ_IE, 663 QCA_WLAN_VENDOR_ATTR_ROAM_AUTH_RESP_IE, 664 QCA_WLAN_VENDOR_ATTR_ROAM_AUTH_AUTHORIZED, 665 QCA_WLAN_VENDOR_ATTR_ROAM_AUTH_KEY_REPLAY_CTR, 666 QCA_WLAN_VENDOR_ATTR_ROAM_AUTH_PTK_KCK, 667 QCA_WLAN_VENDOR_ATTR_ROAM_AUTH_PTK_KEK, 668 QCA_WLAN_VENDOR_ATTR_ROAM_AUTH_SUBNET_STATUS, 669 /* Indicates the status of re-association requested by user space for 670 * the BSSID specified by QCA_WLAN_VENDOR_ATTR_ROAM_AUTH_BSSID. 671 * Type u16. 672 * Represents the status code from AP. Use 673 * %WLAN_STATUS_UNSPECIFIED_FAILURE if the device cannot give you the 674 * real status code for failures. 675 */ 676 QCA_WLAN_VENDOR_ATTR_ROAM_AUTH_STATUS, 677 /* This attribute indicates that the old association was maintained when 678 * a re-association is requested by user space and that re-association 679 * attempt fails (i.e., cannot connect to the requested BSS, but can 680 * remain associated with the BSS with which the association was in 681 * place when being requested to roam). Used along with 682 * WLAN_VENDOR_ATTR_ROAM_AUTH_STATUS to indicate the current 683 * re-association status. Type flag. 684 * This attribute is applicable only for re-association failure cases. 685 */ 686 QCA_WLAN_VENDOR_ATTR_ROAM_AUTH_RETAIN_CONNECTION, 687 /* This attribute specifies the PMK if one was newly generated during 688 * FILS roaming. This is added to the PMKSA cache and is used in 689 * subsequent connections with PMKSA caching. 690 */ 691 QCA_WLAN_VENDOR_ATTR_ROAM_AUTH_PMK = 11, 692 /* This attribute specifies the PMKID used/generated for the current 693 * FILS roam. This is used in subsequent connections with PMKSA caching. 694 */ 695 QCA_WLAN_VENDOR_ATTR_ROAM_AUTH_PMKID = 12, 696 /* A 16-bit unsigned value specifying the next sequence number to use 697 * in ERP message in the currently associated realm. This is used in 698 * doing subsequent ERP based connections in the same realm. 699 */ 700 QCA_WLAN_VENDOR_ATTR_ROAM_AUTH_FILS_ERP_NEXT_SEQ_NUM = 13, 701 /* keep last */ 702 QCA_WLAN_VENDOR_ATTR_ROAM_AUTH_AFTER_LAST, 703 QCA_WLAN_VENDOR_ATTR_ROAM_AUTH_MAX = 704 QCA_WLAN_VENDOR_ATTR_ROAM_AUTH_AFTER_LAST - 1 705 }; 706 707 enum qca_wlan_vendor_attr_p2p_listen_offload { 708 QCA_WLAN_VENDOR_ATTR_P2P_LISTEN_OFFLOAD_INVALID = 0, 709 /* A 32-bit unsigned value; the P2P listen frequency (MHz); must be one 710 * of the social channels. 711 */ 712 QCA_WLAN_VENDOR_ATTR_P2P_LISTEN_OFFLOAD_CHANNEL, 713 /* A 32-bit unsigned value; the P2P listen offload period (ms). 714 */ 715 QCA_WLAN_VENDOR_ATTR_P2P_LISTEN_OFFLOAD_PERIOD, 716 /* A 32-bit unsigned value; the P2P listen interval duration (ms). 717 */ 718 QCA_WLAN_VENDOR_ATTR_P2P_LISTEN_OFFLOAD_INTERVAL, 719 /* A 32-bit unsigned value; number of interval times the firmware needs 720 * to run the offloaded P2P listen operation before it stops. 721 */ 722 QCA_WLAN_VENDOR_ATTR_P2P_LISTEN_OFFLOAD_COUNT, 723 /* An array of arbitrary binary data with one or more 8-byte values. 724 * The device types include both primary and secondary device types. 725 */ 726 QCA_WLAN_VENDOR_ATTR_P2P_LISTEN_OFFLOAD_DEVICE_TYPES, 727 /* An array of unsigned 8-bit characters; vendor information elements. 728 */ 729 QCA_WLAN_VENDOR_ATTR_P2P_LISTEN_OFFLOAD_VENDOR_IE, 730 /* A 32-bit unsigned value; a control flag to indicate whether listen 731 * results need to be flushed to wpa_supplicant. 732 */ 733 QCA_WLAN_VENDOR_ATTR_P2P_LISTEN_OFFLOAD_CTRL_FLAG, 734 /* A 8-bit unsigned value; reason code for P2P listen offload stop 735 * event. 736 */ 737 QCA_WLAN_VENDOR_ATTR_P2P_LISTEN_OFFLOAD_STOP_REASON, 738 /* keep last */ 739 QCA_WLAN_VENDOR_ATTR_P2P_LISTEN_OFFLOAD_AFTER_LAST, 740 QCA_WLAN_VENDOR_ATTR_P2P_LISTEN_OFFLOAD_MAX = 741 QCA_WLAN_VENDOR_ATTR_P2P_LISTEN_OFFLOAD_AFTER_LAST - 1 742 }; 743 744 enum qca_wlan_vendor_attr_acs_offload { 745 QCA_WLAN_VENDOR_ATTR_ACS_CHANNEL_INVALID = 0, 746 QCA_WLAN_VENDOR_ATTR_ACS_PRIMARY_CHANNEL, 747 QCA_WLAN_VENDOR_ATTR_ACS_SECONDARY_CHANNEL, 748 QCA_WLAN_VENDOR_ATTR_ACS_HW_MODE, 749 QCA_WLAN_VENDOR_ATTR_ACS_HT_ENABLED, 750 QCA_WLAN_VENDOR_ATTR_ACS_HT40_ENABLED, 751 QCA_WLAN_VENDOR_ATTR_ACS_VHT_ENABLED, 752 QCA_WLAN_VENDOR_ATTR_ACS_CHWIDTH, 753 QCA_WLAN_VENDOR_ATTR_ACS_CH_LIST, 754 QCA_WLAN_VENDOR_ATTR_ACS_VHT_SEG0_CENTER_CHANNEL, 755 QCA_WLAN_VENDOR_ATTR_ACS_VHT_SEG1_CENTER_CHANNEL, 756 QCA_WLAN_VENDOR_ATTR_ACS_FREQ_LIST, 757 /* keep last */ 758 QCA_WLAN_VENDOR_ATTR_ACS_AFTER_LAST, 759 QCA_WLAN_VENDOR_ATTR_ACS_MAX = 760 QCA_WLAN_VENDOR_ATTR_ACS_AFTER_LAST - 1 761 }; 762 763 enum qca_wlan_vendor_acs_hw_mode { 764 QCA_ACS_MODE_IEEE80211B, 765 QCA_ACS_MODE_IEEE80211G, 766 QCA_ACS_MODE_IEEE80211A, 767 QCA_ACS_MODE_IEEE80211AD, 768 QCA_ACS_MODE_IEEE80211ANY, 769 }; 770 771 /** 772 * enum qca_wlan_vendor_features - Vendor device/driver feature flags 773 * 774 * @QCA_WLAN_VENDOR_FEATURE_KEY_MGMT_OFFLOAD: Device supports key 775 * management offload, a mechanism where the station's firmware 776 * does the exchange with the AP to establish the temporal keys 777 * after roaming, rather than having the user space wpa_supplicant do it. 778 * @QCA_WLAN_VENDOR_FEATURE_SUPPORT_HW_MODE_ANY: Device supports automatic 779 * band selection based on channel selection results. 780 * @QCA_WLAN_VENDOR_FEATURE_OFFCHANNEL_SIMULTANEOUS: Device supports 781 * simultaneous off-channel operations. 782 * @QCA_WLAN_VENDOR_FEATURE_P2P_LISTEN_OFFLOAD: Device supports P2P 783 * Listen offload; a mechanism where the station's firmware takes care of 784 * responding to incoming Probe Request frames received from other P2P 785 * Devices whilst in Listen state, rather than having the user space 786 * wpa_supplicant do it. Information from received P2P requests are 787 * forwarded from firmware to host whenever the host processor wakes up. 788 * @QCA_WLAN_VENDOR_FEATURE_OCE_STA: Device supports all OCE non-AP STA 789 * specific features. 790 * @QCA_WLAN_VENDOR_FEATURE_OCE_AP: Device supports all OCE AP specific 791 * features. 792 * @QCA_WLAN_VENDOR_FEATURE_OCE_STA_CFON: Device supports OCE STA-CFON 793 * specific features only. If a Device sets this bit but not the 794 * %QCA_WLAN_VENDOR_FEATURE_OCE_AP, the userspace shall assume that 795 * this Device may not support all OCE AP functionalities but can support 796 * only OCE STA-CFON functionalities. 797 * @NUM_QCA_WLAN_VENDOR_FEATURES: Number of assigned feature bits 798 */ 799 enum qca_wlan_vendor_features { 800 QCA_WLAN_VENDOR_FEATURE_KEY_MGMT_OFFLOAD = 0, 801 QCA_WLAN_VENDOR_FEATURE_SUPPORT_HW_MODE_ANY = 1, 802 QCA_WLAN_VENDOR_FEATURE_OFFCHANNEL_SIMULTANEOUS = 2, 803 QCA_WLAN_VENDOR_FEATURE_P2P_LISTEN_OFFLOAD = 3, 804 QCA_WLAN_VENDOR_FEATURE_OCE_STA = 4, 805 QCA_WLAN_VENDOR_FEATURE_OCE_AP = 5, 806 QCA_WLAN_VENDOR_FEATURE_OCE_STA_CFON = 6, 807 NUM_QCA_WLAN_VENDOR_FEATURES /* keep last */ 808 }; 809 810 /** 811 * enum qca_wlan_vendor_attr_data_offload_ind - Vendor Data Offload Indication 812 * 813 * @QCA_WLAN_VENDOR_ATTR_DATA_OFFLOAD_IND_SESSION: Session corresponding to 814 * the offloaded data. 815 * @QCA_WLAN_VENDOR_ATTR_DATA_OFFLOAD_IND_PROTOCOL: Protocol of the offloaded 816 * data. 817 * @QCA_WLAN_VENDOR_ATTR_DATA_OFFLOAD_IND_EVENT: Event type for the data offload 818 * indication. 819 */ 820 enum qca_wlan_vendor_attr_data_offload_ind { 821 QCA_WLAN_VENDOR_ATTR_DATA_OFFLOAD_IND_INVALID = 0, 822 QCA_WLAN_VENDOR_ATTR_DATA_OFFLOAD_IND_SESSION, 823 QCA_WLAN_VENDOR_ATTR_DATA_OFFLOAD_IND_PROTOCOL, 824 QCA_WLAN_VENDOR_ATTR_DATA_OFFLOAD_IND_EVENT, 825 826 /* keep last */ 827 QCA_WLAN_VENDOR_ATTR_DATA_OFFLOAD_IND_AFTER_LAST, 828 QCA_WLAN_VENDOR_ATTR_DATA_OFFLOAD_IND_MAX = 829 QCA_WLAN_VENDOR_ATTR_DATA_OFFLOAD_IND_AFTER_LAST - 1 830 }; 831 832 /** 833 * enum qca_wlan_vendor_attr_ocb_set_config - Vendor subcmd attributes to set 834 * OCB config 835 * 836 * @QCA_WLAN_VENDOR_ATTR_OCB_SET_CONFIG_CHANNEL_COUNT: Number of channels in the 837 * configuration 838 * @QCA_WLAN_VENDOR_ATTR_OCB_SET_CONFIG_SCHEDULE_SIZE: Size of the schedule 839 * @QCA_WLAN_VENDOR_ATTR_OCB_SET_CONFIG_CHANNEL_ARRAY: Array of channels 840 * @QCA_WLAN_VENDOR_ATTR_OCB_SET_CONFIG_SCHEDULE_ARRAY: Array of channels to be 841 * scheduled 842 * @QCA_WLAN_VENDOR_ATTR_OCB_SET_CONFIG_NDL_CHANNEL_ARRAY: Array of NDL channel 843 * information 844 * @QCA_WLAN_VENDOR_ATTR_OCB_SET_CONFIG_NDL_ACTIVE_STATE_ARRAY: Array of NDL 845 * active state configuration 846 * @QCA_WLAN_VENDOR_ATTR_OCB_SET_CONFIG_FLAGS: Configuration flags such as 847 * OCB_CONFIG_FLAG_80211_FRAME_MODE 848 * @QCA_WLAN_VENDOR_ATTR_OCB_SET_CONFIG_DEF_TX_PARAM: Default TX parameters to 849 * use in the case that a packet is sent without a TX control header 850 * @QCA_WLAN_VENDOR_ATTR_OCB_SET_CONFIG_TA_MAX_DURATION: Max duration after the 851 * last TA received that the local time set by TA is synchronous to other 852 * communicating OCB STAs. 853 */ 854 enum qca_wlan_vendor_attr_ocb_set_config { 855 QCA_WLAN_VENDOR_ATTR_OCB_SET_CONFIG_INVALID = 0, 856 QCA_WLAN_VENDOR_ATTR_OCB_SET_CONFIG_CHANNEL_COUNT = 1, 857 QCA_WLAN_VENDOR_ATTR_OCB_SET_CONFIG_SCHEDULE_SIZE = 2, 858 QCA_WLAN_VENDOR_ATTR_OCB_SET_CONFIG_CHANNEL_ARRAY = 3, 859 QCA_WLAN_VENDOR_ATTR_OCB_SET_CONFIG_SCHEDULE_ARRAY = 4, 860 QCA_WLAN_VENDOR_ATTR_OCB_SET_CONFIG_NDL_CHANNEL_ARRAY = 5, 861 QCA_WLAN_VENDOR_ATTR_OCB_SET_CONFIG_NDL_ACTIVE_STATE_ARRAY = 6, 862 QCA_WLAN_VENDOR_ATTR_OCB_SET_CONFIG_FLAGS = 7, 863 QCA_WLAN_VENDOR_ATTR_OCB_SET_CONFIG_DEF_TX_PARAM = 8, 864 QCA_WLAN_VENDOR_ATTR_OCB_SET_CONFIG_TA_MAX_DURATION = 9, 865 QCA_WLAN_VENDOR_ATTR_OCB_SET_CONFIG_AFTER_LAST, 866 QCA_WLAN_VENDOR_ATTR_OCB_SET_CONFIG_MAX = 867 QCA_WLAN_VENDOR_ATTR_OCB_SET_CONFIG_AFTER_LAST - 1 868 }; 869 870 /** 871 * enum qca_wlan_vendor_attr_ocb_set_utc_time - Vendor subcmd attributes to set 872 * UTC time 873 * 874 * @QCA_WLAN_VENDOR_ATTR_OCB_SET_UTC_TIME_VALUE: The UTC time as an array of 875 * 10 bytes 876 * @QCA_WLAN_VENDOR_ATTR_OCB_SET_UTC_TIME_ERROR: The time error as an array of 877 * 5 bytes 878 */ 879 enum qca_wlan_vendor_attr_ocb_set_utc_time { 880 QCA_WLAN_VENDOR_ATTR_OCB_SET_UTC_TIME_INVALID = 0, 881 QCA_WLAN_VENDOR_ATTR_OCB_SET_UTC_TIME_VALUE = 1, 882 QCA_WLAN_VENDOR_ATTR_OCB_SET_UTC_TIME_ERROR = 2, 883 QCA_WLAN_VENDOR_ATTR_OCB_SET_UTC_TIME_AFTER_LAST, 884 QCA_WLAN_VENDOR_ATTR_OCB_SET_UTC_TIME_MAX = 885 QCA_WLAN_VENDOR_ATTR_OCB_SET_UTC_TIME_AFTER_LAST - 1 886 }; 887 888 /** 889 * enum qca_wlan_vendor_attr_ocb_start_timing_advert - Vendor subcmd attributes 890 * to start sending timing advert frames 891 * 892 * @QCA_WLAN_VENDOR_ATTR_OCB_START_TIMING_ADVERT_CHANNEL_FREQ: Cannel frequency 893 * on which to send the frames 894 * @QCA_WLAN_VENDOR_ATTR_OCB_START_TIMING_ADVERT_REPEAT_RATE: Number of times 895 * the frame is sent in 5 seconds 896 */ 897 enum qca_wlan_vendor_attr_ocb_start_timing_advert { 898 QCA_WLAN_VENDOR_ATTR_OCB_START_TIMING_ADVERT_INVALID = 0, 899 QCA_WLAN_VENDOR_ATTR_OCB_START_TIMING_ADVERT_CHANNEL_FREQ = 1, 900 QCA_WLAN_VENDOR_ATTR_OCB_START_TIMING_ADVERT_REPEAT_RATE = 2, 901 QCA_WLAN_VENDOR_ATTR_OCB_START_TIMING_ADVERT_AFTER_LAST, 902 QCA_WLAN_VENDOR_ATTR_OCB_START_TIMING_ADVERT_MAX = 903 QCA_WLAN_VENDOR_ATTR_OCB_START_TIMING_ADVERT_AFTER_LAST - 1 904 }; 905 906 /** 907 * enum qca_wlan_vendor_attr_ocb_stop_timing_advert - Vendor subcmd attributes 908 * to stop timing advert 909 * 910 * @QCA_WLAN_VENDOR_ATTR_OCB_STOP_TIMING_ADVERT_CHANNEL_FREQ: The channel 911 * frequency on which to stop the timing advert 912 */ 913 enum qca_wlan_vendor_attr_ocb_stop_timing_advert { 914 QCA_WLAN_VENDOR_ATTR_OCB_STOP_TIMING_ADVERT_INVALID = 0, 915 QCA_WLAN_VENDOR_ATTR_OCB_STOP_TIMING_ADVERT_CHANNEL_FREQ = 1, 916 QCA_WLAN_VENDOR_ATTR_OCB_STOP_TIMING_ADVERT_AFTER_LAST, 917 QCA_WLAN_VENDOR_ATTR_OCB_STOP_TIMING_ADVERT_MAX = 918 QCA_WLAN_VENDOR_ATTR_OCB_STOP_TIMING_ADVERT_AFTER_LAST - 1 919 }; 920 921 /** 922 * enum qca_wlan_vendor_attr_ocb_get_tsf_response - Vendor subcmd attributes to 923 * get TSF timer value 924 * 925 * @QCA_WLAN_VENDOR_ATTR_OCB_GET_TSF_RESP_TIMER_HIGH: Higher 32 bits of the 926 * timer 927 * @QCA_WLAN_VENDOR_ATTR_OCB_GET_TSF_RESP_TIMER_LOW: Lower 32 bits of the timer 928 */ 929 enum qca_wlan_vendor_attr_ocb_get_tsf_resp { 930 QCA_WLAN_VENDOR_ATTR_OCB_GET_TSF_RESP_INVALID = 0, 931 QCA_WLAN_VENDOR_ATTR_OCB_GET_TSF_RESP_TIMER_HIGH = 1, 932 QCA_WLAN_VENDOR_ATTR_OCB_GET_TSF_RESP_TIMER_LOW = 2, 933 QCA_WLAN_VENDOR_ATTR_OCB_GET_TSF_RESP_AFTER_LAST, 934 QCA_WLAN_VENDOR_ATTR_OCB_GET_TSF_RESP_MAX = 935 QCA_WLAN_VENDOR_ATTR_OCB_GET_TSF_RESP_AFTER_LAST - 1 936 }; 937 938 enum qca_vendor_attr_get_preferred_freq_list { 939 QCA_WLAN_VENDOR_ATTR_GET_PREFERRED_FREQ_LIST_INVALID, 940 /* A 32-unsigned value; the interface type/mode for which the preferred 941 * frequency list is requested (see enum qca_iface_type for possible 942 * values); used in GET_PREFERRED_FREQ_LIST command from user-space to 943 * kernel and in the kernel response back to user-space. 944 */ 945 QCA_WLAN_VENDOR_ATTR_GET_PREFERRED_FREQ_LIST_IFACE_TYPE, 946 /* An array of 32-unsigned values; values are frequency (MHz); sent 947 * from kernel space to user space. 948 */ 949 QCA_WLAN_VENDOR_ATTR_GET_PREFERRED_FREQ_LIST, 950 /* keep last */ 951 QCA_WLAN_VENDOR_ATTR_GET_PREFERRED_FREQ_LIST_AFTER_LAST, 952 QCA_WLAN_VENDOR_ATTR_GET_PREFERRED_FREQ_LIST_MAX = 953 QCA_WLAN_VENDOR_ATTR_GET_PREFERRED_FREQ_LIST_AFTER_LAST - 1 954 }; 955 956 enum qca_vendor_attr_probable_oper_channel { 957 QCA_WLAN_VENDOR_ATTR_PROBABLE_OPER_CHANNEL_INVALID, 958 /* 32-bit unsigned value; indicates the connection/iface type likely to 959 * come on this channel (see enum qca_iface_type). 960 */ 961 QCA_WLAN_VENDOR_ATTR_PROBABLE_OPER_CHANNEL_IFACE_TYPE, 962 /* 32-bit unsigned value; the frequency (MHz) of the probable channel */ 963 QCA_WLAN_VENDOR_ATTR_PROBABLE_OPER_CHANNEL_FREQ, 964 /* keep last */ 965 QCA_WLAN_VENDOR_ATTR_PROBABLE_OPER_CHANNEL_AFTER_LAST, 966 QCA_WLAN_VENDOR_ATTR_PROBABLE_OPER_CHANNEL_MAX = 967 QCA_WLAN_VENDOR_ATTR_PROBABLE_OPER_CHANNEL_AFTER_LAST - 1 968 }; 969 970 enum qca_iface_type { 971 QCA_IFACE_TYPE_STA, 972 QCA_IFACE_TYPE_AP, 973 QCA_IFACE_TYPE_P2P_CLIENT, 974 QCA_IFACE_TYPE_P2P_GO, 975 QCA_IFACE_TYPE_IBSS, 976 QCA_IFACE_TYPE_TDLS, 977 }; 978 979 enum qca_set_band { 980 QCA_SETBAND_AUTO, 981 QCA_SETBAND_5G, 982 QCA_SETBAND_2G, 983 }; 984 985 /** 986 * enum qca_access_policy - Access control policy 987 * 988 * Access control policy is applied on the configured IE 989 * (QCA_WLAN_VENDOR_ATTR_CONFIG_ACCESS_POLICY_IE). 990 * To be set with QCA_WLAN_VENDOR_ATTR_CONFIG_ACCESS_POLICY. 991 * 992 * @QCA_ACCESS_POLICY_ACCEPT_UNLESS_LISTED: Deny Wi-Fi connections which match 993 * the specific configuration (IE) set, i.e., allow all the 994 * connections which do not match the configuration. 995 * @QCA_ACCESS_POLICY_DENY_UNLESS_LISTED: Accept Wi-Fi connections which match 996 * the specific configuration (IE) set, i.e., deny all the 997 * connections which do not match the configuration. 998 */ 999 enum qca_access_policy { 1000 QCA_ACCESS_POLICY_ACCEPT_UNLESS_LISTED, 1001 QCA_ACCESS_POLICY_DENY_UNLESS_LISTED, 1002 }; 1003 1004 /** 1005 * enum qca_vendor_attr_get_tsf: Vendor attributes for TSF capture 1006 * @QCA_WLAN_VENDOR_ATTR_TSF_CMD: enum qca_tsf_operation (u32) 1007 * @QCA_WLAN_VENDOR_ATTR_TSF_TIMER_VALUE: Unsigned 64 bit TSF timer value 1008 * @QCA_WLAN_VENDOR_ATTR_TSF_SOC_TIMER_VALUE: Unsigned 64 bit Synchronized 1009 * SOC timer value at TSF capture 1010 */ 1011 enum qca_vendor_attr_tsf_cmd { 1012 QCA_WLAN_VENDOR_ATTR_TSF_INVALID = 0, 1013 QCA_WLAN_VENDOR_ATTR_TSF_CMD, 1014 QCA_WLAN_VENDOR_ATTR_TSF_TIMER_VALUE, 1015 QCA_WLAN_VENDOR_ATTR_TSF_SOC_TIMER_VALUE, 1016 QCA_WLAN_VENDOR_ATTR_TSF_AFTER_LAST, 1017 QCA_WLAN_VENDOR_ATTR_TSF_MAX = 1018 QCA_WLAN_VENDOR_ATTR_TSF_AFTER_LAST - 1 1019 }; 1020 1021 /** 1022 * enum qca_tsf_operation: TSF driver commands 1023 * @QCA_TSF_CAPTURE: Initiate TSF Capture 1024 * @QCA_TSF_GET: Get TSF capture value 1025 * @QCA_TSF_SYNC_GET: Initiate TSF capture and return with captured value 1026 */ 1027 enum qca_tsf_cmd { 1028 QCA_TSF_CAPTURE, 1029 QCA_TSF_GET, 1030 QCA_TSF_SYNC_GET, 1031 }; 1032 1033 /** 1034 * enum qca_vendor_attr_wisa_cmd 1035 * @QCA_WLAN_VENDOR_ATTR_WISA_MODE: WISA mode value (u32) 1036 * WISA setup vendor commands 1037 */ 1038 enum qca_vendor_attr_wisa_cmd { 1039 QCA_WLAN_VENDOR_ATTR_WISA_INVALID = 0, 1040 QCA_WLAN_VENDOR_ATTR_WISA_MODE, 1041 QCA_WLAN_VENDOR_ATTR_WISA_AFTER_LAST, 1042 QCA_WLAN_VENDOR_ATTR_WISA_MAX = 1043 QCA_WLAN_VENDOR_ATTR_WISA_AFTER_LAST - 1 1044 }; 1045 1046 /* IEEE 802.11 Vendor Specific elements */ 1047 1048 /** 1049 * enum qca_vendor_element_id - QCA Vendor Specific element types 1050 * 1051 * These values are used to identify QCA Vendor Specific elements. The 1052 * payload of the element starts with the three octet OUI (OUI_QCA) and 1053 * is followed by a single octet type which is defined by this enum. 1054 * 1055 * @QCA_VENDOR_ELEM_P2P_PREF_CHAN_LIST: P2P preferred channel list. 1056 * This element can be used to specify preference order for supported 1057 * channels. The channels in this list are in preference order (the first 1058 * one has the highest preference) and are described as a pair of 1059 * (global) Operating Class and Channel Number (each one octet) fields. 1060 * 1061 * This extends the standard P2P functionality by providing option to have 1062 * more than one preferred operating channel. When this element is present, 1063 * it replaces the preference indicated in the Operating Channel attribute. 1064 * For supporting other implementations, the Operating Channel attribute is 1065 * expected to be used with the highest preference channel. Similarly, all 1066 * the channels included in this Preferred channel list element are 1067 * expected to be included in the Channel List attribute. 1068 * 1069 * This vendor element may be included in GO Negotiation Request, P2P 1070 * Invitation Request, and Provision Discovery Request frames. 1071 * 1072 * @QCA_VENDOR_ELEM_HE_CAPAB: HE Capabilities element. 1073 * This element can be used for pre-standard publication testing of HE 1074 * before P802.11ax draft assigns the element ID. The payload of this 1075 * vendor specific element is defined by the latest P802.11ax draft. 1076 * Please note that the draft is still work in progress and this element 1077 * payload is subject to change. 1078 * 1079 * @QCA_VENDOR_ELEM_HE_OPER: HE Operation element. 1080 * This element can be used for pre-standard publication testing of HE 1081 * before P802.11ax draft assigns the element ID. The payload of this 1082 * vendor specific element is defined by the latest P802.11ax draft. 1083 * Please note that the draft is still work in progress and this element 1084 * payload is subject to change. 1085 * 1086 * @QCA_VENDOR_ELEM_RAPS: RAPS element (OFDMA-based Random Access Parameter Set 1087 * element). 1088 * This element can be used for pre-standard publication testing of HE 1089 * before P802.11ax draft assigns the element ID extension. The payload of 1090 * this vendor specific element is defined by the latest P802.11ax draft 1091 * (not including the Element ID Extension field). Please note that the 1092 * draft is still work in progress and this element payload is subject to 1093 * change. 1094 * 1095 * @QCA_VENDOR_ELEM_MU_EDCA_PARAMS: MU EDCA Parameter Set element. 1096 * This element can be used for pre-standard publication testing of HE 1097 * before P802.11ax draft assigns the element ID extension. The payload of 1098 * this vendor specific element is defined by the latest P802.11ax draft 1099 * (not including the Element ID Extension field). Please note that the 1100 * draft is still work in progress and this element payload is subject to 1101 * change. 1102 * 1103 * @QCA_VENDOR_ELEM_BSS_COLOR_CHANGE: BSS Color Change Announcement element. 1104 * This element can be used for pre-standard publication testing of HE 1105 * before P802.11ax draft assigns the element ID extension. The payload of 1106 * this vendor specific element is defined by the latest P802.11ax draft 1107 * (not including the Element ID Extension field). Please note that the 1108 * draft is still work in progress and this element payload is subject to 1109 * change. 1110 */ 1111 enum qca_vendor_element_id { 1112 QCA_VENDOR_ELEM_P2P_PREF_CHAN_LIST = 0, 1113 QCA_VENDOR_ELEM_HE_CAPAB = 1, 1114 QCA_VENDOR_ELEM_HE_OPER = 2, 1115 QCA_VENDOR_ELEM_RAPS = 3, 1116 QCA_VENDOR_ELEM_MU_EDCA_PARAMS = 4, 1117 QCA_VENDOR_ELEM_BSS_COLOR_CHANGE = 5, 1118 }; 1119 1120 /** 1121 * enum qca_wlan_vendor_attr_scan - Specifies vendor scan attributes 1122 * 1123 * @QCA_WLAN_VENDOR_ATTR_SCAN_IE: IEs that should be included as part of scan 1124 * @QCA_WLAN_VENDOR_ATTR_SCAN_FREQUENCIES: Nested unsigned 32-bit attributes 1125 * with frequencies to be scanned (in MHz) 1126 * @QCA_WLAN_VENDOR_ATTR_SCAN_SSIDS: Nested attribute with SSIDs to be scanned 1127 * @QCA_WLAN_VENDOR_ATTR_SCAN_SUPP_RATES: Nested array attribute of supported 1128 * rates to be included 1129 * @QCA_WLAN_VENDOR_ATTR_SCAN_TX_NO_CCK_RATE: flag used to send probe requests 1130 * at non CCK rate in 2GHz band 1131 * @QCA_WLAN_VENDOR_ATTR_SCAN_FLAGS: Unsigned 32-bit scan flags 1132 * @QCA_WLAN_VENDOR_ATTR_SCAN_COOKIE: Unsigned 64-bit cookie provided by the 1133 * driver for the specific scan request 1134 * @QCA_WLAN_VENDOR_ATTR_SCAN_STATUS: Unsigned 8-bit status of the scan 1135 * request decoded as in enum scan_status 1136 * @QCA_WLAN_VENDOR_ATTR_SCAN_MAC: 6-byte MAC address to use when randomisation 1137 * scan flag is set 1138 * @QCA_WLAN_VENDOR_ATTR_SCAN_MAC_MASK: 6-byte MAC address mask to be used with 1139 * randomisation 1140 * @QCA_WLAN_VENDOR_ATTR_SCAN_BSSID: 6-byte MAC address representing the 1141 * specific BSSID to scan for. 1142 */ 1143 enum qca_wlan_vendor_attr_scan { 1144 QCA_WLAN_VENDOR_ATTR_SCAN_INVALID_PARAM = 0, 1145 QCA_WLAN_VENDOR_ATTR_SCAN_IE = 1, 1146 QCA_WLAN_VENDOR_ATTR_SCAN_FREQUENCIES = 2, 1147 QCA_WLAN_VENDOR_ATTR_SCAN_SSIDS = 3, 1148 QCA_WLAN_VENDOR_ATTR_SCAN_SUPP_RATES = 4, 1149 QCA_WLAN_VENDOR_ATTR_SCAN_TX_NO_CCK_RATE = 5, 1150 QCA_WLAN_VENDOR_ATTR_SCAN_FLAGS = 6, 1151 QCA_WLAN_VENDOR_ATTR_SCAN_COOKIE = 7, 1152 QCA_WLAN_VENDOR_ATTR_SCAN_STATUS = 8, 1153 QCA_WLAN_VENDOR_ATTR_SCAN_MAC = 9, 1154 QCA_WLAN_VENDOR_ATTR_SCAN_MAC_MASK = 10, 1155 QCA_WLAN_VENDOR_ATTR_SCAN_BSSID = 11, 1156 QCA_WLAN_VENDOR_ATTR_SCAN_AFTER_LAST, 1157 QCA_WLAN_VENDOR_ATTR_SCAN_MAX = 1158 QCA_WLAN_VENDOR_ATTR_SCAN_AFTER_LAST - 1 1159 }; 1160 1161 /** 1162 * enum scan_status - Specifies the valid values the vendor scan attribute 1163 * QCA_WLAN_VENDOR_ATTR_SCAN_STATUS can take 1164 * 1165 * @VENDOR_SCAN_STATUS_NEW_RESULTS: implies the vendor scan is successful with 1166 * new scan results 1167 * @VENDOR_SCAN_STATUS_ABORTED: implies the vendor scan was aborted in-between 1168 */ 1169 enum scan_status { 1170 VENDOR_SCAN_STATUS_NEW_RESULTS, 1171 VENDOR_SCAN_STATUS_ABORTED, 1172 VENDOR_SCAN_STATUS_MAX, 1173 }; 1174 1175 /** 1176 * enum qca_vendor_attr_ota_test - Specifies the values for vendor 1177 * command QCA_NL80211_VENDOR_SUBCMD_OTA_TEST 1178 * @QCA_WLAN_VENDOR_ATTR_OTA_TEST_ENABLE: enable ota test 1179 */ 1180 enum qca_vendor_attr_ota_test { 1181 QCA_WLAN_VENDOR_ATTR_OTA_TEST_INVALID, 1182 /* 8-bit unsigned value to indicate if OTA test is enabled */ 1183 QCA_WLAN_VENDOR_ATTR_OTA_TEST_ENABLE, 1184 /* keep last */ 1185 QCA_WLAN_VENDOR_ATTR_OTA_TEST_AFTER_LAST, 1186 QCA_WLAN_VENDOR_ATTR_OTA_TEST_MAX = 1187 QCA_WLAN_VENDOR_ATTR_OTA_TEST_AFTER_LAST - 1 1188 }; 1189 1190 /** 1191 * enum qca_vendor_attr_txpower_scale - vendor sub commands index 1192 * 1193 * @QCA_WLAN_VENDOR_ATTR_TXPOWER_SCALE: scaling value 1194 */ 1195 enum qca_vendor_attr_txpower_scale { 1196 QCA_WLAN_VENDOR_ATTR_TXPOWER_SCALE_INVALID, 1197 /* 8-bit unsigned value to indicate the scaling of tx power */ 1198 QCA_WLAN_VENDOR_ATTR_TXPOWER_SCALE, 1199 /* keep last */ 1200 QCA_WLAN_VENDOR_ATTR_TXPOWER_SCALE_AFTER_LAST, 1201 QCA_WLAN_VENDOR_ATTR_TXPOWER_SCALE_MAX = 1202 QCA_WLAN_VENDOR_ATTR_TXPOWER_SCALE_AFTER_LAST - 1 1203 }; 1204 1205 /** 1206 * enum qca_vendor_attr_txpower_decr_db - Attributes for TX power decrease 1207 * 1208 * These attributes are used with QCA_NL80211_VENDOR_SUBCMD_SET_TXPOWER_DECR_DB. 1209 */ 1210 enum qca_vendor_attr_txpower_decr_db { 1211 QCA_WLAN_VENDOR_ATTR_TXPOWER_DECR_DB_INVALID, 1212 /* 8-bit unsigned value to indicate the reduction of TX power in dB for 1213 * a virtual interface. */ 1214 QCA_WLAN_VENDOR_ATTR_TXPOWER_DECR_DB, 1215 /* keep last */ 1216 QCA_WLAN_VENDOR_ATTR_TXPOWER_DECR_DB_AFTER_LAST, 1217 QCA_WLAN_VENDOR_ATTR_TXPOWER_DECR_DB_MAX = 1218 QCA_WLAN_VENDOR_ATTR_TXPOWER_DECR_DB_AFTER_LAST - 1 1219 }; 1220 1221 /* Attributes for data used by 1222 * QCA_NL80211_VENDOR_SUBCMD_SET_WIFI_CONFIGURATION and 1223 * QCA_NL80211_VENDOR_SUBCMD_GET_WIFI_CONFIGURATION subcommands. 1224 */ 1225 enum qca_wlan_vendor_attr_config { 1226 QCA_WLAN_VENDOR_ATTR_CONFIG_INVALID = 0, 1227 /* Unsigned 32-bit value to set the DTIM period. 1228 * Whether the wifi chipset wakes at every dtim beacon or a multiple of 1229 * the DTIM period. If DTIM is set to 3, the STA shall wake up every 3 1230 * DTIM beacons. 1231 */ 1232 QCA_WLAN_VENDOR_ATTR_CONFIG_DYNAMIC_DTIM = 1, 1233 /* Unsigned 32-bit value to set the wifi_iface stats averaging factor 1234 * used to calculate statistics like average the TSF offset or average 1235 * number of frame leaked. 1236 * For instance, upon Beacon frame reception: 1237 * current_avg = ((beacon_TSF - TBTT) * factor + previous_avg * (0x10000 - factor) ) / 0x10000 1238 * For instance, when evaluating leaky APs: 1239 * current_avg = ((num frame received within guard time) * factor + previous_avg * (0x10000 - factor)) / 0x10000 1240 */ 1241 QCA_WLAN_VENDOR_ATTR_CONFIG_STATS_AVG_FACTOR = 2, 1242 /* Unsigned 32-bit value to configure guard time, i.e., when 1243 * implementing IEEE power management based on frame control PM bit, how 1244 * long the driver waits before shutting down the radio and after 1245 * receiving an ACK frame for a Data frame with PM bit set. 1246 */ 1247 QCA_WLAN_VENDOR_ATTR_CONFIG_GUARD_TIME = 3, 1248 /* Unsigned 32-bit value to change the FTM capability dynamically */ 1249 QCA_WLAN_VENDOR_ATTR_CONFIG_FINE_TIME_MEASUREMENT = 4, 1250 /* Unsigned 16-bit value to configure maximum TX rate dynamically */ 1251 QCA_WLAN_VENDOR_ATTR_CONF_TX_RATE = 5, 1252 /* Unsigned 32-bit value to configure the number of continuous 1253 * Beacon Miss which shall be used by the firmware to penalize 1254 * the RSSI. 1255 */ 1256 QCA_WLAN_VENDOR_ATTR_CONFIG_PENALIZE_AFTER_NCONS_BEACON_MISS = 6, 1257 /* Unsigned 8-bit value to configure the channel avoidance indication 1258 * behavior. Firmware to send only one indication and ignore duplicate 1259 * indications when set to avoid multiple Apps wakeups. 1260 */ 1261 QCA_WLAN_VENDOR_ATTR_CONFIG_CHANNEL_AVOIDANCE_IND = 7, 1262 /* 8-bit unsigned value to configure the maximum TX MPDU for 1263 * aggregation. */ 1264 QCA_WLAN_VENDOR_ATTR_CONFIG_TX_MPDU_AGGREGATION = 8, 1265 /* 8-bit unsigned value to configure the maximum RX MPDU for 1266 * aggregation. */ 1267 QCA_WLAN_VENDOR_ATTR_CONFIG_RX_MPDU_AGGREGATION = 9, 1268 /* 8-bit unsigned value to configure the Non aggregrate/11g sw 1269 * retry threshold (0 disable, 31 max). */ 1270 QCA_WLAN_VENDOR_ATTR_CONFIG_NON_AGG_RETRY = 10, 1271 /* 8-bit unsigned value to configure the aggregrate sw 1272 * retry threshold (0 disable, 31 max). */ 1273 QCA_WLAN_VENDOR_ATTR_CONFIG_AGG_RETRY = 11, 1274 /* 8-bit unsigned value to configure the MGMT frame 1275 * retry threshold (0 disable, 31 max). */ 1276 QCA_WLAN_VENDOR_ATTR_CONFIG_MGMT_RETRY = 12, 1277 /* 8-bit unsigned value to configure the CTRL frame 1278 * retry threshold (0 disable, 31 max). */ 1279 QCA_WLAN_VENDOR_ATTR_CONFIG_CTRL_RETRY = 13, 1280 /* 8-bit unsigned value to configure the propagation delay for 1281 * 2G/5G band (0~63, units in us) */ 1282 QCA_WLAN_VENDOR_ATTR_CONFIG_PROPAGATION_DELAY = 14, 1283 /* Unsigned 32-bit value to configure the number of unicast TX fail 1284 * packet count. The peer is disconnected once this threshold is 1285 * reached. */ 1286 QCA_WLAN_VENDOR_ATTR_CONFIG_TX_FAIL_COUNT = 15, 1287 /* Attribute used to set scan default IEs to the driver. 1288 * 1289 * These IEs can be used by scan operations that will be initiated by 1290 * the driver/firmware. 1291 * 1292 * For further scan requests coming to the driver, these IEs should be 1293 * merged with the IEs received along with scan request coming to the 1294 * driver. If a particular IE is present in the scan default IEs but not 1295 * present in the scan request, then that IE should be added to the IEs 1296 * sent in the Probe Request frames for that scan request. */ 1297 QCA_WLAN_VENDOR_ATTR_CONFIG_SCAN_DEFAULT_IES = 16, 1298 /* Unsigned 32-bit attribute for generic commands */ 1299 QCA_WLAN_VENDOR_ATTR_CONFIG_GENERIC_COMMAND = 17, 1300 /* Unsigned 32-bit value attribute for generic commands */ 1301 QCA_WLAN_VENDOR_ATTR_CONFIG_GENERIC_VALUE = 18, 1302 /* Unsigned 32-bit data attribute for generic command response */ 1303 QCA_WLAN_VENDOR_ATTR_CONFIG_GENERIC_DATA = 19, 1304 /* Unsigned 32-bit length attribute for 1305 * QCA_WLAN_VENDOR_ATTR_CONFIG_GENERIC_DATA */ 1306 QCA_WLAN_VENDOR_ATTR_CONFIG_GENERIC_LENGTH = 20, 1307 /* Unsigned 32-bit flags attribute for 1308 * QCA_WLAN_VENDOR_ATTR_CONFIG_GENERIC_DATA */ 1309 QCA_WLAN_VENDOR_ATTR_CONFIG_GENERIC_FLAGS = 21, 1310 /* Unsigned 32-bit, defining the access policy. 1311 * See enum qca_access_policy. Used with 1312 * QCA_WLAN_VENDOR_ATTR_CONFIG_ACCESS_POLICY_IE_LIST. */ 1313 QCA_WLAN_VENDOR_ATTR_CONFIG_ACCESS_POLICY = 22, 1314 /* Sets the list of full set of IEs for which a specific access policy 1315 * has to be applied. Used along with 1316 * QCA_WLAN_VENDOR_ATTR_CONFIG_ACCESS_POLICY to control the access. 1317 * Zero length payload can be used to clear this access constraint. */ 1318 QCA_WLAN_VENDOR_ATTR_CONFIG_ACCESS_POLICY_IE_LIST = 23, 1319 /* Unsigned 32-bit, specifies the interface index (netdev) for which the 1320 * corresponding configurations are applied. If the interface index is 1321 * not specified, the configurations are attributed to the respective 1322 * wiphy. */ 1323 QCA_WLAN_VENDOR_ATTR_CONFIG_IFINDEX = 24, 1324 /* 8-bit unsigned value to trigger QPower: 1-Enable, 0-Disable */ 1325 QCA_WLAN_VENDOR_ATTR_CONFIG_QPOWER = 25, 1326 /* 8-bit unsigned value to configure the driver and below layers to 1327 * ignore the assoc disallowed set by APs while connecting 1328 * 1-Ignore, 0-Don't ignore */ 1329 QCA_WLAN_VENDOR_ATTR_CONFIG_IGNORE_ASSOC_DISALLOWED = 26, 1330 /* 32-bit unsigned value to trigger antenna diversity features: 1331 * 1-Enable, 0-Disable */ 1332 QCA_WLAN_VENDOR_ATTR_CONFIG_ANT_DIV_ENA = 27, 1333 /* 32-bit unsigned value to configure specific chain antenna */ 1334 QCA_WLAN_VENDOR_ATTR_CONFIG_ANT_DIV_CHAIN = 28, 1335 /* 32-bit unsigned value to trigger cycle selftest 1336 * 1-Enable, 0-Disable */ 1337 QCA_WLAN_VENDOR_ATTR_CONFIG_ANT_DIV_SELFTEST = 29, 1338 /* 32-bit unsigned to configure the cycle time of selftest 1339 * the unit is micro-second */ 1340 QCA_WLAN_VENDOR_ATTR_CONFIG_ANT_DIV_SELFTEST_INTVL = 30, 1341 /* 32-bit unsigned value to set reorder timeout for AC_VO */ 1342 QCA_WLAN_VENDOR_ATTR_CONFIG_RX_REORDER_TIMEOUT_VOICE = 31, 1343 /* 32-bit unsigned value to set reorder timeout for AC_VI */ 1344 QCA_WLAN_VENDOR_ATTR_CONFIG_RX_REORDER_TIMEOUT_VIDEO = 32, 1345 /* 32-bit unsigned value to set reorder timeout for AC_BE */ 1346 QCA_WLAN_VENDOR_ATTR_CONFIG_RX_REORDER_TIMEOUT_BESTEFFORT = 33, 1347 /* 32-bit unsigned value to set reorder timeout for AC_BK */ 1348 QCA_WLAN_VENDOR_ATTR_CONFIG_RX_REORDER_TIMEOUT_BACKGROUND = 34, 1349 /* 6-byte MAC address to point out the specific peer */ 1350 QCA_WLAN_VENDOR_ATTR_CONFIG_RX_BLOCKSIZE_PEER_MAC = 35, 1351 /* 32-bit unsigned value to set window size for specific peer */ 1352 QCA_WLAN_VENDOR_ATTR_CONFIG_RX_BLOCKSIZE_WINLIMIT = 36, 1353 /* 8-bit unsigned value to set the beacon miss threshold in 2.4 GHz */ 1354 QCA_WLAN_VENDOR_ATTR_CONFIG_BEACON_MISS_THRESHOLD_24 = 37, 1355 /* 8-bit unsigned value to set the beacon miss threshold in 5 GHz */ 1356 QCA_WLAN_VENDOR_ATTR_CONFIG_BEACON_MISS_THRESHOLD_5 = 38, 1357 /* 32-bit unsigned value to configure 5 or 10 MHz channel width for 1358 * station device while in disconnect state. The attribute use the 1359 * value of enum nl80211_chan_width: NL80211_CHAN_WIDTH_5 means 5 MHz, 1360 * NL80211_CHAN_WIDTH_10 means 10 MHz. If set, the device work in 5 or 1361 * 10 MHz channel width, the station will not connect to a BSS using 20 1362 * MHz or higher bandwidth. Set to NL80211_CHAN_WIDTH_20_NOHT to 1363 * clear this constraint. */ 1364 QCA_WLAN_VENDOR_ATTR_CONFIG_SUB20_CHAN_WIDTH = 39, 1365 /* 32-bit unsigned value to configure the propagation absolute delay 1366 * for 2G/5G band (units in us) */ 1367 QCA_WLAN_VENDOR_ATTR_CONFIG_PROPAGATION_ABS_DELAY = 40, 1368 /* 32-bit unsigned value to set probe period */ 1369 QCA_WLAN_VENDOR_ATTR_CONFIG_ANT_DIV_PROBE_PERIOD = 41, 1370 /* 32-bit unsigned value to set stay period */ 1371 QCA_WLAN_VENDOR_ATTR_CONFIG_ANT_DIV_STAY_PERIOD = 42, 1372 /* 32-bit unsigned value to set snr diff */ 1373 QCA_WLAN_VENDOR_ATTR_CONFIG_ANT_DIV_SNR_DIFF = 43, 1374 /* 32-bit unsigned value to set probe dwell time */ 1375 QCA_WLAN_VENDOR_ATTR_CONFIG_ANT_DIV_PROBE_DWELL_TIME = 44, 1376 /* 32-bit unsigned value to set mgmt snr weight */ 1377 QCA_WLAN_VENDOR_ATTR_CONFIG_ANT_DIV_MGMT_SNR_WEIGHT = 45, 1378 /* 32-bit unsigned value to set data snr weight */ 1379 QCA_WLAN_VENDOR_ATTR_CONFIG_ANT_DIV_DATA_SNR_WEIGHT = 46, 1380 /* 32-bit unsigned value to set ack snr weight */ 1381 QCA_WLAN_VENDOR_ATTR_CONFIG_ANT_DIV_ACK_SNR_WEIGHT = 47, 1382 /* 32-bit unsigned value to configure the listen interval. 1383 * This is in units of beacon intervals. This configuration alters 1384 * the negotiated listen interval with the AP during the connection. 1385 * It is highly recommended to configure a value less than or equal to 1386 * the one negotiated during the association. Configuring any greater 1387 * value can have adverse effects (frame loss, AP disassociating STA, 1388 * etc.). 1389 */ 1390 QCA_WLAN_VENDOR_ATTR_CONFIG_LISTEN_INTERVAL = 48, 1391 /* 1392 * 8 bit unsigned value that is set on an AP/GO virtual interface to 1393 * disable operations that would cause the AP/GO to leave its operating 1394 * channel. 1395 * 1396 * This will restrict the scans to the AP/GO operating channel and the 1397 * channels of the other band, if DBS is supported.A STA/CLI interface 1398 * brought up after this setting is enabled, will be restricted to 1399 * connecting to devices only on the AP/GO interface's operating channel 1400 * or on the other band in DBS case. P2P supported channel list is 1401 * modified, to only include AP interface's operating-channel and the 1402 * channels of the other band if DBS is supported. 1403 * 1404 * These restrictions are only applicable as long as the AP/GO interface 1405 * is alive. If the AP/GO interface is brought down then this 1406 * setting/restriction is forgotten. 1407 * 1408 * If this variable is set on an AP/GO interface while a multi-channel 1409 * concurrent session is active, it has no effect on the operation of 1410 * the current interfaces, other than restricting the scan to the AP/GO 1411 * operating channel and the other band channels if DBS is supported. 1412 * However, if the STA is brought down and restarted then the new STA 1413 * connection will either be formed on the AP/GO channel or on the 1414 * other band in a DBS case. This is because of the scan being 1415 * restricted on these channels as mentioned above. 1416 * 1417 * 1-Restrict / 0-Don't restrict offchannel operations. 1418 */ 1419 QCA_WLAN_VENDOR_ATTR_CONFIG_RESTRICT_OFFCHANNEL = 49, 1420 /* 1421 * 8 bit unsigned value to enable/disable LRO (Large Receive Offload) 1422 * on an interface. 1423 * 1 - Enable, 0 - Disable. 1424 */ 1425 QCA_WLAN_VENDOR_ATTR_CONFIG_LRO = 50, 1426 1427 /* 1428 * 8 bit unsigned value to globally enable/disable scan 1429 * 1 - Enable, 0 - Disable. 1430 */ 1431 QCA_WLAN_VENDOR_ATTR_CONFIG_SCAN_ENABLE = 51, 1432 1433 /* 8-bit unsigned value to set the total beacon miss count 1434 * This paramater will set the total beacon miss count. 1435 */ 1436 QCA_WLAN_VENDOR_ATTR_CONFIG_TOTAL_BEACON_MISS_COUNT = 52, 1437 1438 /* Unsigned 32-bit value to configure the number of continuous 1439 * Beacon Miss which shall be used by the firmware to penalize 1440 * the RSSI for BTC. 1441 */ 1442 QCA_WLAN_VENDOR_ATTR_CONFIG_PENALIZE_AFTER_NCONS_BEACON_MISS_BTC = 53, 1443 1444 /* 8-bit unsigned value to configure the driver and below layers to 1445 * enable/disable all FILS features. 1446 * 0-enable, 1-disable */ 1447 QCA_WLAN_VENDOR_ATTR_CONFIG_DISABLE_FILS = 54, 1448 1449 /* keep last */ 1450 QCA_WLAN_VENDOR_ATTR_CONFIG_AFTER_LAST, 1451 QCA_WLAN_VENDOR_ATTR_CONFIG_MAX = 1452 QCA_WLAN_VENDOR_ATTR_CONFIG_AFTER_LAST - 1, 1453 }; 1454 1455 /** 1456 * enum qca_wlan_vendor_attr_sap_config - Parameters for AP configuration 1457 */ 1458 enum qca_wlan_vendor_attr_sap_config { 1459 QCA_WLAN_VENDOR_ATTR_SAP_CONFIG_INVALID = 0, 1460 /* 1 - reserved for QCA */ 1461 /* List of frequencies on which AP is expected to operate. 1462 * This is irrespective of ACS configuration. This list is a priority 1463 * based one and is looked for before the AP is created to ensure the 1464 * best concurrency sessions (avoid MCC and use DBS/SCC) co-exist in 1465 * the system. 1466 */ 1467 QCA_WLAN_VENDOR_ATTR_SAP_MANDATORY_FREQUENCY_LIST = 2, 1468 1469 QCA_WLAN_VENDOR_ATTR_SAP_CONFIG_AFTER_LAST, 1470 QCA_WLAN_VENDOR_ATTR_SAP_CONFIG_MAX = 1471 QCA_WLAN_VENDOR_ATTR_SAP_CONFIG_AFTER_LAST - 1, 1472 }; 1473 1474 /** 1475 * enum qca_wlan_vendor_attr_sap_conditional_chan_switch - Parameters for AP 1476 * conditional channel switch 1477 */ 1478 enum qca_wlan_vendor_attr_sap_conditional_chan_switch { 1479 QCA_WLAN_VENDOR_ATTR_SAP_CONDITIONAL_CHAN_SWITCH_INVALID = 0, 1480 /* Priority based frequency list (an array of u32 values in host byte 1481 * order) */ 1482 QCA_WLAN_VENDOR_ATTR_SAP_CONDITIONAL_CHAN_SWITCH_FREQ_LIST = 1, 1483 /* Status of the conditional switch (u32). 1484 * 0: Success, Non-zero: Failure 1485 */ 1486 QCA_WLAN_VENDOR_ATTR_SAP_CONDITIONAL_CHAN_SWITCH_STATUS = 2, 1487 1488 QCA_WLAN_VENDOR_ATTR_SAP_CONDITIONAL_CHAN_SWITCH_AFTER_LAST, 1489 QCA_WLAN_VENDOR_ATTR_SAP_CONDITIONAL_CHAN_SWITCH_MAX = 1490 QCA_WLAN_VENDOR_ATTR_SAP_CONDITIONAL_CHAN_SWITCH_AFTER_LAST - 1, 1491 }; 1492 1493 /** 1494 * enum qca_wlan_gpio_attr - Parameters for GPIO configuration 1495 */ 1496 enum qca_wlan_gpio_attr { 1497 QCA_WLAN_VENDOR_ATTR_GPIO_PARAM_INVALID = 0, 1498 /* Unsigned 32-bit attribute for GPIO command */ 1499 QCA_WLAN_VENDOR_ATTR_GPIO_PARAM_COMMAND, 1500 /* Unsigned 32-bit attribute for GPIO PIN number to configure */ 1501 QCA_WLAN_VENDOR_ATTR_GPIO_PARAM_PINNUM, 1502 /* Unsigned 32-bit attribute for GPIO value to configure */ 1503 QCA_WLAN_VENDOR_ATTR_GPIO_PARAM_VALUE, 1504 /* Unsigned 32-bit attribute for GPIO pull type */ 1505 QCA_WLAN_VENDOR_ATTR_GPIO_PARAM_PULL_TYPE, 1506 /* Unsigned 32-bit attribute for GPIO interrupt mode */ 1507 QCA_WLAN_VENDOR_ATTR_GPIO_PARAM_INTR_MODE, 1508 1509 /* keep last */ 1510 QCA_WLAN_VENDOR_ATTR_GPIO_PARAM_LAST, 1511 QCA_WLAN_VENDOR_ATTR_GPIO_PARAM_MAX = 1512 QCA_WLAN_VENDOR_ATTR_GPIO_PARAM_LAST - 1 1513 }; 1514 1515 /** 1516 * enum qca_wlan_vendor_attr_get_hw_capability - Wi-Fi hardware capability 1517 */ 1518 enum qca_wlan_vendor_attr_get_hw_capability { 1519 QCA_WLAN_VENDOR_ATTR_HW_CAPABILITY_INVALID, 1520 /* Antenna isolation 1521 * An attribute used in the response. 1522 * The content of this attribute is encoded in a byte array. Each byte 1523 * value is an antenna isolation value. The array length is the number 1524 * of antennas. 1525 */ 1526 QCA_WLAN_VENDOR_ATTR_ANTENNA_ISOLATION, 1527 /* Request HW capability 1528 * An attribute used in the request. 1529 * The content of this attribute is a u32 array for one or more of 1530 * hardware capabilities (attribute IDs) that are being requested. Each 1531 * u32 value has a value from this 1532 * enum qca_wlan_vendor_attr_get_hw_capability 1533 * identifying which capabilities are requested. 1534 */ 1535 QCA_WLAN_VENDOR_ATTR_GET_HW_CAPABILITY, 1536 1537 /* keep last */ 1538 QCA_WLAN_VENDOR_ATTR_HW_CAPABILITY_AFTER_LAST, 1539 QCA_WLAN_VENDOR_ATTR_HW_CAPABILITY_MAX = 1540 QCA_WLAN_VENDOR_ATTR_HW_CAPABILITY_AFTER_LAST - 1, 1541 }; 1542 1543 /** 1544 * enum qca_wlan_vendor_attr_ll_stats_ext - Attributes for MAC layer monitoring 1545 * offload which is an extension for LL_STATS. 1546 * @QCA_WLAN_VENDOR_ATTR_LL_STATS_CFG_PERIOD: Monitoring period. Unit in ms. 1547 * If MAC counters do not exceed the threshold, FW will report monitored 1548 * link layer counters periodically as this setting. The first report is 1549 * always triggered by this timer. 1550 * @QCA_WLAN_VENDOR_ATTR_LL_STATS_CFG_THRESHOLD: It is a percentage (1-99). 1551 * For each MAC layer counter, FW holds two copies. One is the current value. 1552 * The other is the last report. Once a current counter's increment is larger 1553 * than the threshold, FW will indicate that counter to host even if the 1554 * monitoring timer does not expire. 1555 * @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_PEER_PS_CHG: Peer STA power state change 1556 * @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_TID: TID of MSDU 1557 * @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_NUM_MSDU: Count of MSDU with the same 1558 * failure code. 1559 * @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_TX_STATUS: TX failure code 1560 * 1: TX packet discarded 1561 * 2: No ACK 1562 * 3: Postpone 1563 * @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_PEER_MAC_ADDRESS: peer MAC address 1564 * @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_PEER_PS_STATE: Peer STA current state 1565 * @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_GLOBAL: Global threshold. 1566 * Threshold for all monitored parameters. If per counter dedicated threshold 1567 * is not enabled, this threshold will take effect. 1568 * @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_EVENT_MODE: Indicate what triggers this 1569 * event, PERORID_TIMEOUT == 1, THRESH_EXCEED == 0. 1570 * @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_IFACE_ID: interface ID 1571 * @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_PEER_ID: peer ID 1572 * @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_TX_BITMAP: bitmap for TX counters 1573 * Bit0: TX counter unit in MSDU 1574 * Bit1: TX counter unit in MPDU 1575 * Bit2: TX counter unit in PPDU 1576 * Bit3: TX counter unit in byte 1577 * Bit4: Dropped MSDUs 1578 * Bit5: Dropped Bytes 1579 * Bit6: MPDU retry counter 1580 * Bit7: MPDU failure counter 1581 * Bit8: PPDU failure counter 1582 * Bit9: MPDU aggregation counter 1583 * Bit10: MCS counter for ACKed MPDUs 1584 * Bit11: MCS counter for Failed MPDUs 1585 * Bit12: TX Delay counter 1586 * @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_RX_BITMAP: bitmap for RX counters 1587 * Bit0: MAC RX counter unit in MPDU 1588 * Bit1: MAC RX counter unit in byte 1589 * Bit2: PHY RX counter unit in PPDU 1590 * Bit3: PHY RX counter unit in byte 1591 * Bit4: Disorder counter 1592 * Bit5: Retry counter 1593 * Bit6: Duplication counter 1594 * Bit7: Discard counter 1595 * Bit8: MPDU aggregation size counter 1596 * Bit9: MCS counter 1597 * Bit10: Peer STA power state change (wake to sleep) counter 1598 * Bit11: Peer STA power save counter, total time in PS mode 1599 * Bit12: Probe request counter 1600 * Bit13: Other management frames counter 1601 * @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_CCA_BSS_BITMAP: bitmap for CCA 1602 * Bit0: Idle time 1603 * Bit1: TX time 1604 * Bit2: time RX in current bss 1605 * Bit3: Out of current bss time 1606 * Bit4: Wireless medium busy time 1607 * Bit5: RX in bad condition time 1608 * Bit6: TX in bad condition time 1609 * Bit7: time wlan card not available 1610 * @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_SIGNAL_BITMAP: bitmap for signal 1611 * Bit0: Per channel SNR counter 1612 * Bit1: Per channel noise floor counter 1613 * @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_PEER_NUM: number of peers 1614 * @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_CHANNEL_NUM: number of channels 1615 * @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_PEER_AC_RX_NUM: number of RX stats 1616 * @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_CCA_BSS: per channel BSS CCA stats 1617 * @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_PEER: container for per PEER stats 1618 * @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_TX_MSDU: Number of total TX MSDUs 1619 * @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_TX_MPDU: Number of total TX MPDUs 1620 * @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_TX_PPDU: Number of total TX PPDUs 1621 * @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_TX_BYTES: bytes of TX data 1622 * @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_TX_DROP: Number of dropped TX packets 1623 * @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_TX_DROP_BYTES: Bytes dropped 1624 * @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_TX_RETRY: waiting time without an ACK 1625 * @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_TX_NO_ACK: number of MPDU not-ACKed 1626 * @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_TX_NO_BACK: number of PPDU not-ACKed 1627 * @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_TX_AGGR_NUM: 1628 * aggregation stats buffer length 1629 * @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_TX_SUCC_MCS_NUM: length of mcs stats 1630 * buffer for ACKed MPDUs. 1631 * @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_TX_FAIL_MCS_NUM: length of mcs stats 1632 * buffer for failed MPDUs. 1633 * @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_DELAY_ARRAY_SIZE: 1634 * length of delay stats array. 1635 * @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_TX_AGGR: TX aggregation stats 1636 * @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_TX_SUCC_MCS: MCS stats for ACKed MPDUs 1637 * @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_TX_FAIL_MCS: MCS stats for failed MPDUs 1638 * @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_TX_DELAY: tx delay stats 1639 * @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_RX_MPDU: MPDUs received 1640 * @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_RX_MPDU_BYTES: bytes received 1641 * @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_RX_PPDU: PPDU received 1642 * @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_RX_PPDU_BYTES: PPDU bytes received 1643 * @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_RX_MPDU_LOST: packets lost 1644 * @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_RX_MPDU_RETRY: number of RX packets 1645 * flagged as retransmissions 1646 * @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_RX_MPDU_DUP: number of RX packets 1647 * flagged as duplicated 1648 * @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_RX_MPDU_DISCARD: number of RX 1649 * packets discarded 1650 * @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_RX_AGGR_NUM: length of RX aggregation 1651 * stats buffer. 1652 * @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_RX_MCS_NUM: length of RX mcs 1653 * stats buffer. 1654 * @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_RX_MCS: RX mcs stats buffer 1655 * @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_RX_AGGR: aggregation stats buffer 1656 * @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_PEER_PS_TIMES: times STAs go to sleep 1657 * @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_PEER_PS_DURATION: STAs' total sleep time 1658 * @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_RX_PROBE_REQ: number of probe 1659 * requests received 1660 * @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_RX_MGMT: number of other mgmt 1661 * frames received 1662 * @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_IDLE_TIME: Percentage of idle time 1663 * there is no TX, nor RX, nor interference. 1664 * @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_TX_TIME: percentage of time 1665 * transmitting packets. 1666 * @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_RX_TIME: percentage of time 1667 * for receiving. 1668 * @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_RX_BUSY: percentage of time 1669 * interference detected. 1670 * @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_RX_BAD: percentage of time 1671 * receiving packets with errors. 1672 * @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_TX_BAD: percentage of time 1673 * TX no-ACK. 1674 * @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_NO_AVAIL: percentage of time 1675 * the chip is unable to work in normal conditions. 1676 * @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_IN_BSS_TIME: percentage of time 1677 * receiving packets in current BSS. 1678 * @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_OUT_BSS_TIME: percentage of time 1679 * receiving packets not in current BSS. 1680 * @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_PEER_ANT_NUM: number of antennas 1681 * @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_PEER_SIGNAL: 1682 * This is a container for per antenna signal stats. 1683 * @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_ANT_SNR: per antenna SNR value 1684 * @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_ANT_NF: per antenna NF value 1685 * @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_IFACE_RSSI_BEACON: RSSI of beacon 1686 * @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_IFACE_SNR_BEACON: SNR of beacon 1687 */ 1688 enum qca_wlan_vendor_attr_ll_stats_ext { 1689 QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_INVALID = 0, 1690 1691 /* Attributes for configurations */ 1692 QCA_WLAN_VENDOR_ATTR_LL_STATS_CFG_PERIOD, 1693 QCA_WLAN_VENDOR_ATTR_LL_STATS_CFG_THRESHOLD, 1694 1695 /* Peer STA power state change */ 1696 QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_PEER_PS_CHG, 1697 1698 /* TX failure event */ 1699 QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_TID, 1700 QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_NUM_MSDU, 1701 QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_TX_STATUS, 1702 1703 QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_PEER_PS_STATE, 1704 QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_PEER_MAC_ADDRESS, 1705 1706 /* MAC counters */ 1707 QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_GLOBAL, 1708 QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_EVENT_MODE, 1709 QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_IFACE_ID, 1710 QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_PEER_ID, 1711 QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_TX_BITMAP, 1712 QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_RX_BITMAP, 1713 QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_CCA_BSS_BITMAP, 1714 QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_SIGNAL_BITMAP, 1715 QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_PEER_NUM, 1716 QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_CHANNEL_NUM, 1717 QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_CCA_BSS, 1718 QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_PEER, 1719 1720 /* Sub-attributes for PEER_AC_TX */ 1721 QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_TX_MSDU, 1722 QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_TX_MPDU, 1723 QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_TX_PPDU, 1724 QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_TX_BYTES, 1725 QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_TX_DROP, 1726 QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_TX_DROP_BYTES, 1727 QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_TX_RETRY, 1728 QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_TX_NO_ACK, 1729 QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_TX_NO_BACK, 1730 QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_TX_AGGR_NUM, 1731 QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_TX_SUCC_MCS_NUM, 1732 QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_TX_FAIL_MCS_NUM, 1733 QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_TX_AGGR, 1734 QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_TX_SUCC_MCS, 1735 QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_TX_FAIL_MCS, 1736 QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_DELAY_ARRAY_SIZE, 1737 QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_TX_DELAY, 1738 1739 /* Sub-attributes for PEER_AC_RX */ 1740 QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_RX_MPDU, 1741 QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_RX_MPDU_BYTES, 1742 QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_RX_PPDU, 1743 QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_RX_PPDU_BYTES, 1744 QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_RX_MPDU_LOST, 1745 QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_RX_MPDU_RETRY, 1746 QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_RX_MPDU_DUP, 1747 QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_RX_MPDU_DISCARD, 1748 QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_RX_AGGR_NUM, 1749 QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_RX_MCS_NUM, 1750 QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_RX_MCS, 1751 QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_RX_AGGR, 1752 QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_PEER_PS_TIMES, 1753 QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_PEER_PS_DURATION, 1754 QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_RX_PROBE_REQ, 1755 QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_RX_MGMT, 1756 1757 /* Sub-attributes for CCA_BSS */ 1758 QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_IDLE_TIME, 1759 QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_TX_TIME, 1760 QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_RX_TIME, 1761 QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_RX_BUSY, 1762 QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_RX_BAD, 1763 QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_TX_BAD, 1764 QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_NO_AVAIL, 1765 1766 /* sub-attribute for BSS_RX_TIME */ 1767 QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_IN_BSS_TIME, 1768 QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_OUT_BSS_TIME, 1769 1770 /* Sub-attributes for PEER_SIGNAL */ 1771 QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_PEER_ANT_NUM, 1772 QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_PEER_SIGNAL, 1773 QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_ANT_SNR, 1774 QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_ANT_NF, 1775 1776 /* Sub-attributes for IFACE_BSS */ 1777 QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_IFACE_RSSI_BEACON, 1778 QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_IFACE_SNR_BEACON, 1779 1780 QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_LAST, 1781 QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_MAX = 1782 QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_LAST - 1 1783 }; 1784 1785 /* Attributes for FTM commands and events */ 1786 1787 /** 1788 * enum qca_wlan_vendor_attr_loc_capa - Indoor location capabilities 1789 * 1790 * @QCA_WLAN_VENDOR_ATTR_LOC_CAPA_FLAGS: Various flags. See 1791 * enum qca_wlan_vendor_attr_loc_capa_flags. 1792 * @QCA_WLAN_VENDOR_ATTR_FTM_CAPA_MAX_NUM_SESSIONS: Maximum number 1793 * of measurement sessions that can run concurrently. 1794 * Default is one session (no session concurrency). 1795 * @QCA_WLAN_VENDOR_ATTR_FTM_CAPA_MAX_NUM_PEERS: The total number of unique 1796 * peers that are supported in running sessions. For example, 1797 * if the value is 8 and maximum number of sessions is 2, you can 1798 * have one session with 8 unique peers, or 2 sessions with 4 unique 1799 * peers each, and so on. 1800 * @QCA_WLAN_VENDOR_ATTR_FTM_CAPA_MAX_NUM_BURSTS_EXP: Maximum number 1801 * of bursts per peer, as an exponent (2^value). Default is 0, 1802 * meaning no multi-burst support. 1803 * @QCA_WLAN_VENDOR_ATTR_FTM_CAPA_MAX_MEAS_PER_BURST: Maximum number 1804 * of measurement exchanges allowed in a single burst. 1805 * @QCA_WLAN_VENDOR_ATTR_AOA_CAPA_SUPPORTED_TYPES: Supported AOA measurement 1806 * types. A bit mask (unsigned 32 bit value), each bit corresponds 1807 * to an AOA type as defined by enum qca_vendor_attr_aoa_type. 1808 */ 1809 enum qca_wlan_vendor_attr_loc_capa { 1810 QCA_WLAN_VENDOR_ATTR_LOC_CAPA_INVALID, 1811 QCA_WLAN_VENDOR_ATTR_LOC_CAPA_FLAGS, 1812 QCA_WLAN_VENDOR_ATTR_FTM_CAPA_MAX_NUM_SESSIONS, 1813 QCA_WLAN_VENDOR_ATTR_FTM_CAPA_MAX_NUM_PEERS, 1814 QCA_WLAN_VENDOR_ATTR_FTM_CAPA_MAX_NUM_BURSTS_EXP, 1815 QCA_WLAN_VENDOR_ATTR_FTM_CAPA_MAX_MEAS_PER_BURST, 1816 QCA_WLAN_VENDOR_ATTR_AOA_CAPA_SUPPORTED_TYPES, 1817 /* keep last */ 1818 QCA_WLAN_VENDOR_ATTR_LOC_CAPA_AFTER_LAST, 1819 QCA_WLAN_VENDOR_ATTR_LOC_CAPA_MAX = 1820 QCA_WLAN_VENDOR_ATTR_LOC_CAPA_AFTER_LAST - 1, 1821 }; 1822 1823 /** 1824 * enum qca_wlan_vendor_attr_loc_capa_flags: Indoor location capability flags 1825 * 1826 * @QCA_WLAN_VENDOR_ATTR_LOC_CAPA_FLAG_FTM_RESPONDER: Set if driver 1827 * can be configured as an FTM responder (for example, an AP that 1828 * services FTM requests). QCA_NL80211_VENDOR_SUBCMD_FTM_CFG_RESPONDER 1829 * will be supported if set. 1830 * @QCA_WLAN_VENDOR_ATTR_LOC_CAPA_FLAG_FTM_INITIATOR: Set if driver 1831 * can run FTM sessions. QCA_NL80211_VENDOR_SUBCMD_FTM_START_SESSION 1832 * will be supported if set. 1833 * @QCA_WLAN_VENDOR_ATTR_LOC_CAPA_FLAG_ASAP: Set if FTM responder 1834 * supports immediate (ASAP) response. 1835 * @QCA_WLAN_VENDOR_ATTR_LOC_CAPA_FLAG_AOA: Set if driver supports standalone 1836 * AOA measurement using QCA_NL80211_VENDOR_SUBCMD_AOA_MEAS. 1837 * @QCA_WLAN_VENDOR_ATTR_LOC_CAPA_FLAG_AOA_IN_FTM: Set if driver supports 1838 * requesting AOA measurements as part of an FTM session. 1839 */ 1840 enum qca_wlan_vendor_attr_loc_capa_flags { 1841 QCA_WLAN_VENDOR_ATTR_LOC_CAPA_FLAG_FTM_RESPONDER = 1 << 0, 1842 QCA_WLAN_VENDOR_ATTR_LOC_CAPA_FLAG_FTM_INITIATOR = 1 << 1, 1843 QCA_WLAN_VENDOR_ATTR_LOC_CAPA_FLAG_ASAP = 1 << 2, 1844 QCA_WLAN_VENDOR_ATTR_LOC_CAPA_FLAG_AOA = 1 << 3, 1845 QCA_WLAN_VENDOR_ATTR_LOC_CAPA_FLAG_AOA_IN_FTM = 1 << 4, 1846 }; 1847 1848 /** 1849 * enum qca_wlan_vendor_attr_ftm_peer_info: Information about 1850 * a single peer in a measurement session. 1851 * 1852 * @QCA_WLAN_VENDOR_ATTR_FTM_PEER_MAC_ADDR: The MAC address of the peer. 1853 * @QCA_WLAN_VENDOR_ATTR_FTM_PEER_MEAS_FLAGS: Various flags related 1854 * to measurement. See enum qca_wlan_vendor_attr_ftm_peer_meas_flags. 1855 * @QCA_WLAN_VENDOR_ATTR_FTM_PEER_MEAS_PARAMS: Nested attribute of 1856 * FTM measurement parameters, as specified by IEEE P802.11-REVmc/D7.0 1857 * 9.4.2.167. See enum qca_wlan_vendor_attr_ftm_meas_param for 1858 * list of supported attributes. 1859 * @QCA_WLAN_VENDOR_ATTR_FTM_PEER_SECURE_TOKEN_ID: Initial token ID for 1860 * secure measurement. 1861 * @QCA_WLAN_VENDOR_ATTR_FTM_PEER_AOA_BURST_PERIOD: Request AOA 1862 * measurement every <value> bursts. If 0 or not specified, 1863 * AOA measurements will be disabled for this peer. 1864 * @QCA_WLAN_VENDOR_ATTR_FTM_PEER_FREQ: Frequency in MHz where 1865 * the measurement frames are exchanged. Optional; if not 1866 * specified, try to locate the peer in the kernel scan 1867 * results cache and use frequency from there. 1868 */ 1869 enum qca_wlan_vendor_attr_ftm_peer_info { 1870 QCA_WLAN_VENDOR_ATTR_FTM_PEER_INVALID, 1871 QCA_WLAN_VENDOR_ATTR_FTM_PEER_MAC_ADDR, 1872 QCA_WLAN_VENDOR_ATTR_FTM_PEER_MEAS_FLAGS, 1873 QCA_WLAN_VENDOR_ATTR_FTM_PEER_MEAS_PARAMS, 1874 QCA_WLAN_VENDOR_ATTR_FTM_PEER_SECURE_TOKEN_ID, 1875 QCA_WLAN_VENDOR_ATTR_FTM_PEER_AOA_BURST_PERIOD, 1876 QCA_WLAN_VENDOR_ATTR_FTM_PEER_FREQ, 1877 /* keep last */ 1878 QCA_WLAN_VENDOR_ATTR_FTM_PEER_AFTER_LAST, 1879 QCA_WLAN_VENDOR_ATTR_FTM_PEER_MAX = 1880 QCA_WLAN_VENDOR_ATTR_FTM_PEER_AFTER_LAST - 1, 1881 }; 1882 1883 /** 1884 * enum qca_wlan_vendor_attr_ftm_peer_meas_flags: Measurement request flags, 1885 * per-peer 1886 * 1887 * @QCA_WLAN_VENDOR_ATTR_FTM_PEER_MEAS_FLAG_ASAP: If set, request 1888 * immediate (ASAP) response from peer. 1889 * @QCA_WLAN_VENDOR_ATTR_FTM_PEER_MEAS_FLAG_LCI: If set, request 1890 * LCI report from peer. The LCI report includes the absolute 1891 * location of the peer in "official" coordinates (similar to GPS). 1892 * See IEEE P802.11-REVmc/D7.0, 11.24.6.7 for more information. 1893 * @QCA_WLAN_VENDOR_ATTR_FTM_PEER_MEAS_FLAG_LCR: If set, request 1894 * Location civic report from peer. The LCR includes the location 1895 * of the peer in free-form format. See IEEE P802.11-REVmc/D7.0, 1896 * 11.24.6.7 for more information. 1897 * @QCA_WLAN_VENDOR_ATTR_FTM_PEER_MEAS_FLAG_SECURE: If set, 1898 * request a secure measurement. 1899 * QCA_WLAN_VENDOR_ATTR_FTM_PEER_SECURE_TOKEN_ID must also be provided. 1900 */ 1901 enum qca_wlan_vendor_attr_ftm_peer_meas_flags { 1902 QCA_WLAN_VENDOR_ATTR_FTM_PEER_MEAS_FLAG_ASAP = 1 << 0, 1903 QCA_WLAN_VENDOR_ATTR_FTM_PEER_MEAS_FLAG_LCI = 1 << 1, 1904 QCA_WLAN_VENDOR_ATTR_FTM_PEER_MEAS_FLAG_LCR = 1 << 2, 1905 QCA_WLAN_VENDOR_ATTR_FTM_PEER_MEAS_FLAG_SECURE = 1 << 3, 1906 }; 1907 1908 /** 1909 * enum qca_wlan_vendor_attr_ftm_meas_param: Measurement parameters 1910 * 1911 * @QCA_WLAN_VENDOR_ATTR_FTM_PARAM_MEAS_PER_BURST: Number of measurements 1912 * to perform in a single burst. 1913 * @QCA_WLAN_VENDOR_ATTR_FTM_PARAM_NUM_BURSTS_EXP: Number of bursts to 1914 * perform, specified as an exponent (2^value). 1915 * @QCA_WLAN_VENDOR_ATTR_FTM_PARAM_BURST_DURATION: Duration of burst 1916 * instance, as specified in IEEE P802.11-REVmc/D7.0, 9.4.2.167. 1917 * @QCA_WLAN_VENDOR_ATTR_FTM_PARAM_BURST_PERIOD: Time between bursts, 1918 * as specified in IEEE P802.11-REVmc/D7.0, 9.4.2.167. Must 1919 * be larger than QCA_WLAN_VENDOR_ATTR_FTM_PARAM_BURST_DURATION. 1920 */ 1921 enum qca_wlan_vendor_attr_ftm_meas_param { 1922 QCA_WLAN_VENDOR_ATTR_FTM_PARAM_INVALID, 1923 QCA_WLAN_VENDOR_ATTR_FTM_PARAM_MEAS_PER_BURST, 1924 QCA_WLAN_VENDOR_ATTR_FTM_PARAM_NUM_BURSTS_EXP, 1925 QCA_WLAN_VENDOR_ATTR_FTM_PARAM_BURST_DURATION, 1926 QCA_WLAN_VENDOR_ATTR_FTM_PARAM_BURST_PERIOD, 1927 /* keep last */ 1928 QCA_WLAN_VENDOR_ATTR_FTM_PARAM_AFTER_LAST, 1929 QCA_WLAN_VENDOR_ATTR_FTM_PARAM_MAX = 1930 QCA_WLAN_VENDOR_ATTR_FTM_PARAM_AFTER_LAST - 1, 1931 }; 1932 1933 /** 1934 * enum qca_wlan_vendor_attr_ftm_peer_result: Per-peer results 1935 * 1936 * @QCA_WLAN_VENDOR_ATTR_FTM_PEER_RES_MAC_ADDR: MAC address of the reported 1937 * peer. 1938 * @QCA_WLAN_VENDOR_ATTR_FTM_PEER_RES_STATUS: Status of measurement 1939 * request for this peer. 1940 * See enum qca_wlan_vendor_attr_ftm_peer_result_status. 1941 * @QCA_WLAN_VENDOR_ATTR_FTM_PEER_RES_FLAGS: Various flags related 1942 * to measurement results for this peer. 1943 * See enum qca_wlan_vendor_attr_ftm_peer_result_flags. 1944 * @QCA_WLAN_VENDOR_ATTR_FTM_PEER_RES_VALUE_SECONDS: Specified when 1945 * request failed and peer requested not to send an additional request 1946 * for this number of seconds. 1947 * @QCA_WLAN_VENDOR_ATTR_FTM_PEER_RES_LCI: LCI report when received 1948 * from peer. In the format specified by IEEE P802.11-REVmc/D7.0, 1949 * 9.4.2.22.10. 1950 * @QCA_WLAN_VENDOR_ATTR_FTM_PEER_RES_LCR: Location civic report when 1951 * received from peer. In the format specified by IEEE P802.11-REVmc/D7.0, 1952 * 9.4.2.22.13. 1953 * @QCA_WLAN_VENDOR_ATTR_FTM_PEER_RES_MEAS_PARAMS: Reported when peer 1954 * overridden some measurement request parameters. See 1955 * enum qca_wlan_vendor_attr_ftm_meas_param. 1956 * @QCA_WLAN_VENDOR_ATTR_FTM_PEER_RES_AOA_MEAS: AOA measurement 1957 * for this peer. Same contents as @QCA_WLAN_VENDOR_ATTR_AOA_MEAS_RESULT. 1958 * @QCA_WLAN_VENDOR_ATTR_FTM_PEER_RES_MEAS: Array of measurement 1959 * results. Each entry is a nested attribute defined 1960 * by enum qca_wlan_vendor_attr_ftm_meas. 1961 */ 1962 enum qca_wlan_vendor_attr_ftm_peer_result { 1963 QCA_WLAN_VENDOR_ATTR_FTM_PEER_RES_INVALID, 1964 QCA_WLAN_VENDOR_ATTR_FTM_PEER_RES_MAC_ADDR, 1965 QCA_WLAN_VENDOR_ATTR_FTM_PEER_RES_STATUS, 1966 QCA_WLAN_VENDOR_ATTR_FTM_PEER_RES_FLAGS, 1967 QCA_WLAN_VENDOR_ATTR_FTM_PEER_RES_VALUE_SECONDS, 1968 QCA_WLAN_VENDOR_ATTR_FTM_PEER_RES_LCI, 1969 QCA_WLAN_VENDOR_ATTR_FTM_PEER_RES_LCR, 1970 QCA_WLAN_VENDOR_ATTR_FTM_PEER_RES_MEAS_PARAMS, 1971 QCA_WLAN_VENDOR_ATTR_FTM_PEER_RES_AOA_MEAS, 1972 QCA_WLAN_VENDOR_ATTR_FTM_PEER_RES_MEAS, 1973 /* keep last */ 1974 QCA_WLAN_VENDOR_ATTR_FTM_PEER_RES_AFTER_LAST, 1975 QCA_WLAN_VENDOR_ATTR_FTM_PEER_RES_MAX = 1976 QCA_WLAN_VENDOR_ATTR_FTM_PEER_RES_AFTER_LAST - 1, 1977 }; 1978 1979 /** 1980 * enum qca_wlan_vendor_attr_ftm_peer_result_status 1981 * 1982 * @QCA_WLAN_VENDOR_ATTR_FTM_PEER_RES_STATUS_OK: Request sent ok and results 1983 * will be provided. Peer may have overridden some measurement parameters, 1984 * in which case overridden parameters will be report by 1985 * QCA_WLAN_VENDOR_ATTR_FTM_PEER_RES_MEAS_PARAM attribute. 1986 * @QCA_WLAN_VENDOR_ATTR_FTM_PEER_RES_STATUS_INCAPABLE: Peer is incapable 1987 * of performing the measurement request. No more results will be sent 1988 * for this peer in this session. 1989 * @QCA_WLAN_VENDOR_ATTR_FTM_PEER_RES_STATUS_FAILED: Peer reported request 1990 * failed, and requested not to send an additional request for number 1991 * of seconds specified by QCA_WLAN_VENDOR_ATTR_FTM_PEER_RES_VALUE_SECONDS 1992 * attribute. 1993 * @QCA_WLAN_VENDOR_ATTR_FTM_PEER_RES_STATUS_INVALID: Request validation 1994 * failed. Request was not sent over the air. 1995 */ 1996 enum qca_wlan_vendor_attr_ftm_peer_result_status { 1997 QCA_WLAN_VENDOR_ATTR_FTM_PEER_RES_STATUS_OK, 1998 QCA_WLAN_VENDOR_ATTR_FTM_PEER_RES_STATUS_INCAPABLE, 1999 QCA_WLAN_VENDOR_ATTR_FTM_PEER_RES_STATUS_FAILED, 2000 QCA_WLAN_VENDOR_ATTR_FTM_PEER_RES_STATUS_INVALID, 2001 }; 2002 2003 /** 2004 * enum qca_wlan_vendor_attr_ftm_peer_result_flags: Various flags 2005 * for measurement result, per-peer 2006 * 2007 * @QCA_WLAN_VENDOR_ATTR_FTM_PEER_RES_FLAG_DONE: If set, 2008 * measurement completed for this peer. No more results will be reported 2009 * for this peer in this session. 2010 */ 2011 enum qca_wlan_vendor_attr_ftm_peer_result_flags { 2012 QCA_WLAN_VENDOR_ATTR_FTM_PEER_RES_FLAG_DONE = 1 << 0, 2013 }; 2014 2015 /** 2016 * enum qca_vendor_attr_loc_session_status: Session completion status code 2017 * 2018 * @QCA_WLAN_VENDOR_ATTR_LOC_SESSION_STATUS_OK: Session completed 2019 * successfully. 2020 * @QCA_WLAN_VENDOR_ATTR_LOC_SESSION_STATUS_ABORTED: Session aborted 2021 * by request. 2022 * @QCA_WLAN_VENDOR_ATTR_LOC_SESSION_STATUS_INVALID: Session request 2023 * was invalid and was not started. 2024 * @QCA_WLAN_VENDOR_ATTR_LOC_SESSION_STATUS_FAILED: Session had an error 2025 * and did not complete normally (for example out of resources). 2026 */ 2027 enum qca_vendor_attr_loc_session_status { 2028 QCA_WLAN_VENDOR_ATTR_LOC_SESSION_STATUS_OK, 2029 QCA_WLAN_VENDOR_ATTR_LOC_SESSION_STATUS_ABORTED, 2030 QCA_WLAN_VENDOR_ATTR_LOC_SESSION_STATUS_INVALID, 2031 QCA_WLAN_VENDOR_ATTR_LOC_SESSION_STATUS_FAILED, 2032 }; 2033 2034 /** 2035 * enum qca_wlan_vendor_attr_ftm_meas: Single measurement data 2036 * 2037 * @QCA_WLAN_VENDOR_ATTR_FTM_MEAS_T1: Time of departure (TOD) of FTM packet as 2038 * recorded by responder, in picoseconds. 2039 * See IEEE P802.11-REVmc/D7.0, 11.24.6.4 for more information. 2040 * @QCA_WLAN_VENDOR_ATTR_FTM_MEAS_T2: Time of arrival (TOA) of FTM packet at 2041 * initiator, in picoseconds. 2042 * See IEEE P802.11-REVmc/D7.0, 11.24.6.4 for more information. 2043 * @QCA_WLAN_VENDOR_ATTR_FTM_MEAS_T3: TOD of ACK packet as recorded by 2044 * initiator, in picoseconds. 2045 * See IEEE P802.11-REVmc/D7.0, 11.24.6.4 for more information. 2046 * @QCA_WLAN_VENDOR_ATTR_FTM_MEAS_T4: TOA of ACK packet at 2047 * responder, in picoseconds. 2048 * See IEEE P802.11-REVmc/D7.0, 11.24.6.4 for more information. 2049 * @QCA_WLAN_VENDOR_ATTR_FTM_MEAS_RSSI: RSSI (signal level) as recorded 2050 * during this measurement exchange. Optional and will be provided if 2051 * the hardware can measure it. 2052 * @QCA_WLAN_VENDOR_ATTR_FTM_MEAS_TOD_ERR: TOD error reported by 2053 * responder. Not always provided. 2054 * See IEEE P802.11-REVmc/D7.0, 9.6.8.33 for more information. 2055 * @QCA_WLAN_VENDOR_ATTR_FTM_MEAS_TOA_ERR: TOA error reported by 2056 * responder. Not always provided. 2057 * See IEEE P802.11-REVmc/D7.0, 9.6.8.33 for more information. 2058 * @QCA_WLAN_VENDOR_ATTR_FTM_MEAS_INITIATOR_TOD_ERR: TOD error measured by 2059 * initiator. Not always provided. 2060 * See IEEE P802.11-REVmc/D7.0, 9.6.8.33 for more information. 2061 * @QCA_WLAN_VENDOR_ATTR_FTM_MEAS_INITIATOR_TOA_ERR: TOA error measured by 2062 * initiator. Not always provided. 2063 * See IEEE P802.11-REVmc/D7.0, 9.6.8.33 for more information. 2064 * @QCA_WLAN_VENDOR_ATTR_FTM_MEAS_PAD: Dummy attribute for padding. 2065 */ 2066 enum qca_wlan_vendor_attr_ftm_meas { 2067 QCA_WLAN_VENDOR_ATTR_FTM_MEAS_INVALID, 2068 QCA_WLAN_VENDOR_ATTR_FTM_MEAS_T1, 2069 QCA_WLAN_VENDOR_ATTR_FTM_MEAS_T2, 2070 QCA_WLAN_VENDOR_ATTR_FTM_MEAS_T3, 2071 QCA_WLAN_VENDOR_ATTR_FTM_MEAS_T4, 2072 QCA_WLAN_VENDOR_ATTR_FTM_MEAS_RSSI, 2073 QCA_WLAN_VENDOR_ATTR_FTM_MEAS_TOD_ERR, 2074 QCA_WLAN_VENDOR_ATTR_FTM_MEAS_TOA_ERR, 2075 QCA_WLAN_VENDOR_ATTR_FTM_MEAS_INITIATOR_TOD_ERR, 2076 QCA_WLAN_VENDOR_ATTR_FTM_MEAS_INITIATOR_TOA_ERR, 2077 QCA_WLAN_VENDOR_ATTR_FTM_MEAS_PAD, 2078 /* keep last */ 2079 QCA_WLAN_VENDOR_ATTR_FTM_MEAS_AFTER_LAST, 2080 QCA_WLAN_VENDOR_ATTR_FTM_MEAS_MAX = 2081 QCA_WLAN_VENDOR_ATTR_FTM_MEAS_AFTER_LAST - 1, 2082 }; 2083 2084 /** 2085 * enum qca_wlan_vendor_attr_aoa_type - AOA measurement type 2086 * 2087 * @QCA_WLAN_VENDOR_ATTR_AOA_TYPE_TOP_CIR_PHASE: Phase of the strongest 2088 * CIR (channel impulse response) path for each antenna. 2089 * @QCA_WLAN_VENDOR_ATTR_AOA_TYPE_TOP_CIR_PHASE_AMP: Phase and amplitude 2090 * of the strongest CIR path for each antenna. 2091 */ 2092 enum qca_wlan_vendor_attr_aoa_type { 2093 QCA_WLAN_VENDOR_ATTR_AOA_TYPE_TOP_CIR_PHASE, 2094 QCA_WLAN_VENDOR_ATTR_AOA_TYPE_TOP_CIR_PHASE_AMP, 2095 QCA_WLAN_VENDOR_ATTR_AOA_TYPE_MAX 2096 }; 2097 2098 /** 2099 * enum qca_wlan_vendor_attr_encryption_test - Attributes to 2100 * validate encryption engine 2101 * 2102 * @QCA_WLAN_VENDOR_ATTR_ENCRYPTION_TEST_NEEDS_DECRYPTION: Flag attribute. 2103 * This will be included if the request is for decryption; if not included, 2104 * the request is treated as a request for encryption by default. 2105 * @QCA_WLAN_VENDOR_ATTR_ENCRYPTION_TEST_CIPHER: Unsigned 32-bit value 2106 * indicating the key cipher suite. Takes same values as 2107 * NL80211_ATTR_KEY_CIPHER. 2108 * @QCA_WLAN_VENDOR_ATTR_ENCRYPTION_TEST_KEYID: Unsigned 8-bit value 2109 * Key Id to be used for encryption 2110 * @QCA_WLAN_VENDOR_ATTR_ENCRYPTION_TEST_TK: Array of 8-bit values. 2111 * Key (TK) to be used for encryption/decryption 2112 * @QCA_WLAN_VENDOR_ATTR_ENCRYPTION_TEST_PN: Array of 8-bit values. 2113 * Packet number to be specified for encryption/decryption 2114 * 6 bytes for TKIP/CCMP/GCMP. 2115 * @QCA_WLAN_VENDOR_ATTR_ENCRYPTION_TEST_DATA: Array of 8-bit values 2116 * representing the 802.11 packet (header + payload + FCS) that 2117 * needs to be encrypted/decrypted. 2118 * Encrypted/decrypted response from the driver will also be sent 2119 * to userspace with the same attribute. 2120 */ 2121 enum qca_wlan_vendor_attr_encryption_test { 2122 QCA_WLAN_VENDOR_ATTR_ENCRYPTION_TEST_INVALID = 0, 2123 QCA_WLAN_VENDOR_ATTR_ENCRYPTION_TEST_NEEDS_DECRYPTION, 2124 QCA_WLAN_VENDOR_ATTR_ENCRYPTION_TEST_CIPHER, 2125 QCA_WLAN_VENDOR_ATTR_ENCRYPTION_TEST_KEYID, 2126 QCA_WLAN_VENDOR_ATTR_ENCRYPTION_TEST_TK, 2127 QCA_WLAN_VENDOR_ATTR_ENCRYPTION_TEST_PN, 2128 QCA_WLAN_VENDOR_ATTR_ENCRYPTION_TEST_DATA, 2129 2130 /* keep last */ 2131 QCA_WLAN_VENDOR_ATTR_ENCRYPTION_TEST_AFTER_LAST, 2132 QCA_WLAN_VENDOR_ATTR_ENCRYPTION_TEST_MAX = 2133 QCA_WLAN_VENDOR_ATTR_ENCRYPTION_TEST_AFTER_LAST - 1 2134 }; 2135 2136 /** 2137 * enum qca_wlan_vendor_attr_dmg_rf_sector_type - Type of 2138 * sector for DMG RF sector operations. 2139 * 2140 * @QCA_WLAN_VENDOR_ATTR_DMG_RF_SECTOR_TYPE_RX: RX sector 2141 * @QCA_WLAN_VENDOR_ATTR_DMG_RF_SECTOR_TYPE_TX: TX sector 2142 */ 2143 enum qca_wlan_vendor_attr_dmg_rf_sector_type { 2144 QCA_WLAN_VENDOR_ATTR_DMG_RF_SECTOR_TYPE_RX, 2145 QCA_WLAN_VENDOR_ATTR_DMG_RF_SECTOR_TYPE_TX, 2146 QCA_WLAN_VENDOR_ATTR_DMG_RF_SECTOR_TYPE_MAX 2147 }; 2148 2149 /** 2150 * BRP antenna limit mode 2151 * 2152 * @QCA_WLAN_VENDOR_ATTR_BRP_ANT_LIMIT_MODE_DISABLE: Disable BRP force 2153 * antenna limit, BRP will be performed as usual. 2154 * @QCA_WLAN_VENDOR_ATTR_BRP_ANT_LIMIT_MODE_EFFECTIVE: Define maximal 2155 * antennas limit. the hardware may use less antennas than the 2156 * maximum limit. 2157 * @QCA_WLAN_VENDOR_ATTR_BRP_ANT_LIMIT_MODE_FORCE: The hardware will 2158 * use exactly the specified number of antennas for BRP. 2159 */ 2160 enum qca_wlan_vendor_attr_brp_ant_limit_mode { 2161 QCA_WLAN_VENDOR_ATTR_BRP_ANT_LIMIT_MODE_DISABLE, 2162 QCA_WLAN_VENDOR_ATTR_BRP_ANT_LIMIT_MODE_EFFECTIVE, 2163 QCA_WLAN_VENDOR_ATTR_BRP_ANT_LIMIT_MODE_FORCE, 2164 QCA_WLAN_VENDOR_ATTR_BRP_ANT_LIMIT_MODE_MAX 2165 }; 2166 2167 /** 2168 * enum qca_wlan_vendor_attr_dmg_rf_sector_cfg - Attributes for 2169 * DMG RF sector configuration for a single RF module. 2170 * The values are defined in a compact way which closely matches 2171 * the way it is stored in HW registers. 2172 * The configuration provides values for 32 antennas and 8 distribution 2173 * amplifiers, and together describes the characteristics of the RF 2174 * sector - such as a beam in some direction with some gain. 2175 * 2176 * @QCA_WLAN_VENDOR_ATTR_DMG_RF_SECTOR_CFG_MODULE_INDEX: Index 2177 * of RF module for this configuration. 2178 * @QCA_WLAN_VENDOR_ATTR_DMG_RF_SECTOR_CFG_ETYPE0: Bit 0 of edge 2179 * amplifier gain index. Unsigned 32 bit number containing 2180 * bits for all 32 antennas. 2181 * @QCA_WLAN_VENDOR_ATTR_DMG_RF_SECTOR_CFG_ETYPE1: Bit 1 of edge 2182 * amplifier gain index. Unsigned 32 bit number containing 2183 * bits for all 32 antennas. 2184 * @QCA_WLAN_VENDOR_ATTR_DMG_RF_SECTOR_CFG_ETYPE2: Bit 2 of edge 2185 * amplifier gain index. Unsigned 32 bit number containing 2186 * bits for all 32 antennas. 2187 * @QCA_WLAN_VENDOR_ATTR_DMG_RF_SECTOR_CFG_PSH_HI: Phase values 2188 * for first 16 antennas, 2 bits per antenna. 2189 * @QCA_WLAN_VENDOR_ATTR_DMG_RF_SECTOR_CFG_PSH_LO: Phase values 2190 * for last 16 antennas, 2 bits per antenna. 2191 * @QCA_WLAN_VENDOR_ATTR_DMG_RF_SECTOR_CFG_DTYPE_X16: Contains 2192 * DTYPE values (3 bits) for each distribution amplifier, followed 2193 * by X16 switch bits for each distribution amplifier. There are 2194 * total of 8 distribution amplifiers. 2195 */ 2196 enum qca_wlan_vendor_attr_dmg_rf_sector_cfg { 2197 QCA_WLAN_VENDOR_ATTR_DMG_RF_SECTOR_CFG_INVALID = 0, 2198 QCA_WLAN_VENDOR_ATTR_DMG_RF_SECTOR_CFG_MODULE_INDEX = 1, 2199 QCA_WLAN_VENDOR_ATTR_DMG_RF_SECTOR_CFG_ETYPE0 = 2, 2200 QCA_WLAN_VENDOR_ATTR_DMG_RF_SECTOR_CFG_ETYPE1 = 3, 2201 QCA_WLAN_VENDOR_ATTR_DMG_RF_SECTOR_CFG_ETYPE2 = 4, 2202 QCA_WLAN_VENDOR_ATTR_DMG_RF_SECTOR_CFG_PSH_HI = 5, 2203 QCA_WLAN_VENDOR_ATTR_DMG_RF_SECTOR_CFG_PSH_LO = 6, 2204 QCA_WLAN_VENDOR_ATTR_DMG_RF_SECTOR_CFG_DTYPE_X16 = 7, 2205 2206 /* keep last */ 2207 QCA_WLAN_VENDOR_ATTR_DMG_RF_SECTOR_CFG_AFTER_LAST, 2208 QCA_WLAN_VENDOR_ATTR_DMG_RF_SECTOR_CFG_MAX = 2209 QCA_WLAN_VENDOR_ATTR_DMG_RF_SECTOR_CFG_AFTER_LAST - 1 2210 }; 2211 2212 enum qca_wlan_vendor_attr_ll_stats_set { 2213 QCA_WLAN_VENDOR_ATTR_LL_STATS_SET_INVALID = 0, 2214 /* Unsigned 32-bit value */ 2215 QCA_WLAN_VENDOR_ATTR_LL_STATS_SET_CONFIG_MPDU_SIZE_THRESHOLD = 1, 2216 QCA_WLAN_VENDOR_ATTR_LL_STATS_SET_CONFIG_AGGRESSIVE_STATS_GATHERING = 2, 2217 /* keep last */ 2218 QCA_WLAN_VENDOR_ATTR_LL_STATS_SET_AFTER_LAST, 2219 QCA_WLAN_VENDOR_ATTR_LL_STATS_SET_MAX = 2220 QCA_WLAN_VENDOR_ATTR_LL_STATS_SET_AFTER_LAST - 1, 2221 }; 2222 2223 enum qca_wlan_vendor_attr_ll_stats_clr { 2224 QCA_WLAN_VENDOR_ATTR_LL_STATS_CLR_INVALID = 0, 2225 /* Unsigned 32bit bitmap for clearing statistics 2226 * All radio statistics 0x00000001 2227 * cca_busy_time (within radio statistics) 0x00000002 2228 * All channel stats (within radio statistics) 0x00000004 2229 * All scan statistics (within radio statistics) 0x00000008 2230 * All interface statistics 0x00000010 2231 * All tx rate statistics (within interface statistics) 0x00000020 2232 * All ac statistics (with in interface statistics) 0x00000040 2233 * All contention (min, max, avg) statistics (within ac statisctics) 2234 * 0x00000080. 2235 */ 2236 QCA_WLAN_VENDOR_ATTR_LL_STATS_CLR_CONFIG_REQ_MASK = 1, 2237 /* Unsigned 8 bit value: Request to stop statistics collection */ 2238 QCA_WLAN_VENDOR_ATTR_LL_STATS_CLR_CONFIG_STOP_REQ = 2, 2239 2240 /* Unsigned 32 bit bitmap: Response from the driver 2241 * for the cleared statistics 2242 */ 2243 QCA_WLAN_VENDOR_ATTR_LL_STATS_CLR_CONFIG_RSP_MASK = 3, 2244 /* Unsigned 8 bit value: Response from driver/firmware 2245 * for the stop request 2246 */ 2247 QCA_WLAN_VENDOR_ATTR_LL_STATS_CLR_CONFIG_STOP_RSP = 4, 2248 /* keep last */ 2249 QCA_WLAN_VENDOR_ATTR_LL_STATS_CLR_AFTER_LAST, 2250 QCA_WLAN_VENDOR_ATTR_LL_STATS_CLR_MAX = 2251 QCA_WLAN_VENDOR_ATTR_LL_STATS_CLR_AFTER_LAST - 1, 2252 }; 2253 2254 enum qca_wlan_vendor_attr_ll_stats_get { 2255 QCA_WLAN_VENDOR_ATTR_LL_STATS_GET_INVALID = 0, 2256 /* Unsigned 32 bit value provided by the caller issuing the GET stats 2257 * command. When reporting the stats results, the driver uses the same 2258 * value to indicate which GET request the results correspond to. 2259 */ 2260 QCA_WLAN_VENDOR_ATTR_LL_STATS_GET_CONFIG_REQ_ID = 1, 2261 /* Unsigned 32 bit value - bit mask to identify what statistics are 2262 * requested for retrieval. 2263 * Radio Statistics 0x00000001 2264 * Interface Statistics 0x00000020 2265 * All Peer Statistics 0x00000040 2266 * Peer Statistics 0x00000080 2267 */ 2268 QCA_WLAN_VENDOR_ATTR_LL_STATS_GET_CONFIG_REQ_MASK = 2, 2269 /* keep last */ 2270 QCA_WLAN_VENDOR_ATTR_LL_STATS_GET_AFTER_LAST, 2271 QCA_WLAN_VENDOR_ATTR_LL_STATS_GET_MAX = 2272 QCA_WLAN_VENDOR_ATTR_LL_STATS_GET_AFTER_LAST - 1, 2273 }; 2274 2275 enum qca_wlan_vendor_attr_ll_stats_results { 2276 QCA_WLAN_VENDOR_ATTR_LL_STATS_INVALID = 0, 2277 /* Unsigned 32bit value. Used by the driver; must match the request id 2278 * provided with the QCA_NL80211_VENDOR_SUBCMD_LL_STATS_GET command. 2279 */ 2280 QCA_WLAN_VENDOR_ATTR_LL_STATS_RESULTS_REQ_ID = 1, 2281 2282 /* Unsigned 32 bit value */ 2283 QCA_WLAN_VENDOR_ATTR_LL_STATS_IFACE_BEACON_RX = 2, 2284 /* Unsigned 32 bit value */ 2285 QCA_WLAN_VENDOR_ATTR_LL_STATS_IFACE_MGMT_RX = 3, 2286 /* Unsigned 32 bit value */ 2287 QCA_WLAN_VENDOR_ATTR_LL_STATS_IFACE_MGMT_ACTION_RX = 4, 2288 /* Unsigned 32 bit value */ 2289 QCA_WLAN_VENDOR_ATTR_LL_STATS_IFACE_MGMT_ACTION_TX = 5, 2290 /* Signed 32 bit value */ 2291 QCA_WLAN_VENDOR_ATTR_LL_STATS_IFACE_RSSI_MGMT = 6, 2292 /* Signed 32 bit value */ 2293 QCA_WLAN_VENDOR_ATTR_LL_STATS_IFACE_RSSI_DATA = 7, 2294 /* Signed 32 bit value */ 2295 QCA_WLAN_VENDOR_ATTR_LL_STATS_IFACE_RSSI_ACK = 8, 2296 2297 /* Attributes of type QCA_WLAN_VENDOR_ATTR_LL_STATS_IFACE_INFO_* are 2298 * nested within the interface stats. 2299 */ 2300 2301 /* Interface mode, e.g., STA, SOFTAP, IBSS, etc. 2302 * Type = enum wifi_interface_mode. 2303 */ 2304 QCA_WLAN_VENDOR_ATTR_LL_STATS_IFACE_INFO_MODE = 9, 2305 /* Interface MAC address. An array of 6 Unsigned int8 */ 2306 QCA_WLAN_VENDOR_ATTR_LL_STATS_IFACE_INFO_MAC_ADDR = 10, 2307 /* Type = enum wifi_connection_state, e.g., DISCONNECTED, 2308 * AUTHENTICATING, etc. valid for STA, CLI only. 2309 */ 2310 QCA_WLAN_VENDOR_ATTR_LL_STATS_IFACE_INFO_STATE = 11, 2311 /* Type = enum wifi_roam_state. Roaming state, e.g., IDLE or ACTIVE 2312 */ 2313 QCA_WLAN_VENDOR_ATTR_LL_STATS_IFACE_INFO_ROAMING = 12, 2314 /* Unsigned 32 bit value. WIFI_CAPABILITY_XXX */ 2315 QCA_WLAN_VENDOR_ATTR_LL_STATS_IFACE_INFO_CAPABILITIES = 13, 2316 /* NULL terminated SSID. An array of 33 Unsigned 8bit values */ 2317 QCA_WLAN_VENDOR_ATTR_LL_STATS_IFACE_INFO_SSID = 14, 2318 /* BSSID. An array of 6 unsigned 8 bit values */ 2319 QCA_WLAN_VENDOR_ATTR_LL_STATS_IFACE_INFO_BSSID = 15, 2320 /* Country string advertised by AP. An array of 3 unsigned 8 bit 2321 * values. 2322 */ 2323 QCA_WLAN_VENDOR_ATTR_LL_STATS_IFACE_INFO_AP_COUNTRY_STR = 16, 2324 /* Country string for this association. An array of 3 unsigned 8 bit 2325 * values. 2326 */ 2327 QCA_WLAN_VENDOR_ATTR_LL_STATS_IFACE_INFO_COUNTRY_STR = 17, 2328 2329 /* Attributes of type QCA_WLAN_VENDOR_ATTR_LL_STATS_WMM_AC_* could 2330 * be nested within the interface stats. 2331 */ 2332 2333 /* Type = enum wifi_traffic_ac, e.g., V0, VI, BE and BK */ 2334 QCA_WLAN_VENDOR_ATTR_LL_STATS_WMM_AC_AC = 18, 2335 /* Unsigned int 32 value corresponding to respective AC */ 2336 QCA_WLAN_VENDOR_ATTR_LL_STATS_WMM_AC_TX_MPDU = 19, 2337 /* Unsigned int 32 value corresponding to respective AC */ 2338 QCA_WLAN_VENDOR_ATTR_LL_STATS_WMM_AC_RX_MPDU = 20, 2339 /* Unsigned int 32 value corresponding to respective AC */ 2340 QCA_WLAN_VENDOR_ATTR_LL_STATS_WMM_AC_TX_MCAST = 21, 2341 /* Unsigned int 32 value corresponding to respective AC */ 2342 QCA_WLAN_VENDOR_ATTR_LL_STATS_WMM_AC_RX_MCAST = 22, 2343 /* Unsigned int 32 value corresponding to respective AC */ 2344 QCA_WLAN_VENDOR_ATTR_LL_STATS_WMM_AC_RX_AMPDU = 23, 2345 /* Unsigned int 32 value corresponding to respective AC */ 2346 QCA_WLAN_VENDOR_ATTR_LL_STATS_WMM_AC_TX_AMPDU = 24, 2347 /* Unsigned int 32 value corresponding to respective AC */ 2348 QCA_WLAN_VENDOR_ATTR_LL_STATS_WMM_AC_MPDU_LOST = 25, 2349 /* Unsigned int 32 value corresponding to respective AC */ 2350 QCA_WLAN_VENDOR_ATTR_LL_STATS_WMM_AC_RETRIES = 26, 2351 /* Unsigned int 32 value corresponding to respective AC */ 2352 QCA_WLAN_VENDOR_ATTR_LL_STATS_WMM_AC_RETRIES_SHORT = 27, 2353 /* Unsigned int 32 values corresponding to respective AC */ 2354 QCA_WLAN_VENDOR_ATTR_LL_STATS_WMM_AC_RETRIES_LONG = 28, 2355 /* Unsigned int 32 values corresponding to respective AC */ 2356 QCA_WLAN_VENDOR_ATTR_LL_STATS_WMM_AC_CONTENTION_TIME_MIN = 29, 2357 /* Unsigned int 32 values corresponding to respective AC */ 2358 QCA_WLAN_VENDOR_ATTR_LL_STATS_WMM_AC_CONTENTION_TIME_MAX = 30, 2359 /* Unsigned int 32 values corresponding to respective AC */ 2360 QCA_WLAN_VENDOR_ATTR_LL_STATS_WMM_AC_CONTENTION_TIME_AVG = 31, 2361 /* Unsigned int 32 values corresponding to respective AC */ 2362 QCA_WLAN_VENDOR_ATTR_LL_STATS_WMM_AC_CONTENTION_NUM_SAMPLES = 32, 2363 /* Unsigned 32 bit value. Number of peers */ 2364 QCA_WLAN_VENDOR_ATTR_LL_STATS_IFACE_NUM_PEERS = 33, 2365 2366 /* Attributes of type QCA_WLAN_VENDOR_ATTR_LL_STATS_PEER_INFO_* are 2367 * nested within the interface stats. 2368 */ 2369 2370 /* Type = enum wifi_peer_type. Peer type, e.g., STA, AP, P2P GO etc. */ 2371 QCA_WLAN_VENDOR_ATTR_LL_STATS_PEER_INFO_TYPE = 34, 2372 /* MAC addr corresponding to respective peer. An array of 6 unsigned 2373 * 8 bit values. 2374 */ 2375 QCA_WLAN_VENDOR_ATTR_LL_STATS_PEER_INFO_MAC_ADDRESS = 35, 2376 /* Unsigned int 32 bit value representing capabilities corresponding 2377 * to respective peer. 2378 */ 2379 QCA_WLAN_VENDOR_ATTR_LL_STATS_PEER_INFO_CAPABILITIES = 36, 2380 /* Unsigned 32 bit value. Number of rates */ 2381 QCA_WLAN_VENDOR_ATTR_LL_STATS_PEER_INFO_NUM_RATES = 37, 2382 2383 /* Attributes of type QCA_WLAN_VENDOR_ATTR_LL_STATS_RATE_* 2384 * are nested within the rate stat. 2385 */ 2386 2387 /* Wi-Fi Rate - separate attributes defined for individual fields */ 2388 2389 /* Unsigned int 8 bit value; 0: OFDM, 1:CCK, 2:HT 3:VHT 4..7 reserved */ 2390 QCA_WLAN_VENDOR_ATTR_LL_STATS_RATE_PREAMBLE = 38, 2391 /* Unsigned int 8 bit value; 0:1x1, 1:2x2, 3:3x3, 4:4x4 */ 2392 QCA_WLAN_VENDOR_ATTR_LL_STATS_RATE_NSS = 39, 2393 /* Unsigned int 8 bit value; 0:20 MHz, 1:40 MHz, 2:80 MHz, 3:160 MHz */ 2394 QCA_WLAN_VENDOR_ATTR_LL_STATS_RATE_BW = 40, 2395 /* Unsigned int 8 bit value; OFDM/CCK rate code would be as per IEEE Std 2396 * in the units of 0.5 Mbps HT/VHT it would be MCS index */ 2397 QCA_WLAN_VENDOR_ATTR_LL_STATS_RATE_MCS_INDEX = 41, 2398 2399 /* Unsigned 32 bit value. Bit rate in units of 100 kbps */ 2400 QCA_WLAN_VENDOR_ATTR_LL_STATS_RATE_BIT_RATE = 42, 2401 2402 2403 /* Attributes of type QCA_WLAN_VENDOR_ATTR_LL_STATS_RATE_STAT_* could be 2404 * nested within the peer info stats. 2405 */ 2406 2407 /* Unsigned int 32 bit value. Number of successfully transmitted data 2408 * packets, i.e., with ACK received corresponding to the respective 2409 * rate. 2410 */ 2411 QCA_WLAN_VENDOR_ATTR_LL_STATS_RATE_TX_MPDU = 43, 2412 /* Unsigned int 32 bit value. Number of received data packets 2413 * corresponding to the respective rate. 2414 */ 2415 QCA_WLAN_VENDOR_ATTR_LL_STATS_RATE_RX_MPDU = 44, 2416 /* Unsigned int 32 bit value. Number of data packet losses, i.e., no ACK 2417 * received corresponding to the respective rate. 2418 */ 2419 QCA_WLAN_VENDOR_ATTR_LL_STATS_RATE_MPDU_LOST = 45, 2420 /* Unsigned int 32 bit value. Total number of data packet retries for 2421 * the respective rate. 2422 */ 2423 QCA_WLAN_VENDOR_ATTR_LL_STATS_RATE_RETRIES = 46, 2424 /* Unsigned int 32 bit value. Total number of short data packet retries 2425 * for the respective rate. 2426 */ 2427 QCA_WLAN_VENDOR_ATTR_LL_STATS_RATE_RETRIES_SHORT = 47, 2428 /* Unsigned int 32 bit value. Total number of long data packet retries 2429 * for the respective rate. 2430 */ 2431 QCA_WLAN_VENDOR_ATTR_LL_STATS_RATE_RETRIES_LONG = 48, 2432 2433 QCA_WLAN_VENDOR_ATTR_LL_STATS_RADIO_ID = 49, 2434 /* Unsigned 32 bit value. Total number of msecs the radio is awake 2435 * accruing over time. 2436 */ 2437 QCA_WLAN_VENDOR_ATTR_LL_STATS_RADIO_ON_TIME = 50, 2438 /* Unsigned 32 bit value. Total number of msecs the radio is 2439 * transmitting accruing over time. 2440 */ 2441 QCA_WLAN_VENDOR_ATTR_LL_STATS_RADIO_TX_TIME = 51, 2442 /* Unsigned 32 bit value. Total number of msecs the radio is in active 2443 * receive accruing over time. 2444 */ 2445 QCA_WLAN_VENDOR_ATTR_LL_STATS_RADIO_RX_TIME = 52, 2446 /* Unsigned 32 bit value. Total number of msecs the radio is awake due 2447 * to all scan accruing over time. 2448 */ 2449 QCA_WLAN_VENDOR_ATTR_LL_STATS_RADIO_ON_TIME_SCAN = 53, 2450 /* Unsigned 32 bit value. Total number of msecs the radio is awake due 2451 * to NAN accruing over time. 2452 */ 2453 QCA_WLAN_VENDOR_ATTR_LL_STATS_RADIO_ON_TIME_NBD = 54, 2454 /* Unsigned 32 bit value. Total number of msecs the radio is awake due 2455 * to GSCAN accruing over time. 2456 */ 2457 QCA_WLAN_VENDOR_ATTR_LL_STATS_RADIO_ON_TIME_GSCAN = 55, 2458 /* Unsigned 32 bit value. Total number of msecs the radio is awake due 2459 * to roam scan accruing over time. 2460 */ 2461 QCA_WLAN_VENDOR_ATTR_LL_STATS_RADIO_ON_TIME_ROAM_SCAN = 56, 2462 /* Unsigned 32 bit value. Total number of msecs the radio is awake due 2463 * to PNO scan accruing over time. 2464 */ 2465 QCA_WLAN_VENDOR_ATTR_LL_STATS_RADIO_ON_TIME_PNO_SCAN = 57, 2466 /* Unsigned 32 bit value. Total number of msecs the radio is awake due 2467 * to Hotspot 2.0 scans and GAS exchange accruing over time. 2468 */ 2469 QCA_WLAN_VENDOR_ATTR_LL_STATS_RADIO_ON_TIME_HS20 = 58, 2470 /* Unsigned 32 bit value. Number of channels. */ 2471 QCA_WLAN_VENDOR_ATTR_LL_STATS_RADIO_NUM_CHANNELS = 59, 2472 2473 /* Attributes of type QCA_WLAN_VENDOR_ATTR_LL_STATS_CHANNEL_INFO_* could 2474 * be nested within the channel stats. 2475 */ 2476 2477 /* Type = enum wifi_channel_width. Channel width, e.g., 20, 40, 80 */ 2478 QCA_WLAN_VENDOR_ATTR_LL_STATS_CHANNEL_INFO_WIDTH = 60, 2479 /* Unsigned 32 bit value. Primary 20 MHz channel. */ 2480 QCA_WLAN_VENDOR_ATTR_LL_STATS_CHANNEL_INFO_CENTER_FREQ = 61, 2481 /* Unsigned 32 bit value. Center frequency (MHz) first segment. */ 2482 QCA_WLAN_VENDOR_ATTR_LL_STATS_CHANNEL_INFO_CENTER_FREQ0 = 62, 2483 /* Unsigned 32 bit value. Center frequency (MHz) second segment. */ 2484 QCA_WLAN_VENDOR_ATTR_LL_STATS_CHANNEL_INFO_CENTER_FREQ1 = 63, 2485 2486 /* Attributes of type QCA_WLAN_VENDOR_ATTR_LL_STATS_CHANNEL_* could be 2487 * nested within the radio stats. 2488 */ 2489 2490 /* Unsigned int 32 bit value representing total number of msecs the 2491 * radio is awake on that channel accruing over time, corresponding to 2492 * the respective channel. 2493 */ 2494 QCA_WLAN_VENDOR_ATTR_LL_STATS_CHANNEL_ON_TIME = 64, 2495 /* Unsigned int 32 bit value representing total number of msecs the CCA 2496 * register is busy accruing over time corresponding to the respective 2497 * channel. 2498 */ 2499 QCA_WLAN_VENDOR_ATTR_LL_STATS_CHANNEL_CCA_BUSY_TIME = 65, 2500 2501 QCA_WLAN_VENDOR_ATTR_LL_STATS_NUM_RADIOS = 66, 2502 2503 /* Signifies the nested list of channel attributes 2504 * QCA_WLAN_VENDOR_ATTR_LL_STATS_CHANNEL_INFO_* 2505 */ 2506 QCA_WLAN_VENDOR_ATTR_LL_STATS_CH_INFO = 67, 2507 2508 /* Signifies the nested list of peer info attributes 2509 * QCA_WLAN_VENDOR_ATTR_LL_STATS_PEER_INFO_* 2510 */ 2511 QCA_WLAN_VENDOR_ATTR_LL_STATS_PEER_INFO = 68, 2512 2513 /* Signifies the nested list of rate info attributes 2514 * QCA_WLAN_VENDOR_ATTR_LL_STATS_RATE_* 2515 */ 2516 QCA_WLAN_VENDOR_ATTR_LL_STATS_PEER_INFO_RATE_INFO = 69, 2517 2518 /* Signifies the nested list of wmm info attributes 2519 * QCA_WLAN_VENDOR_ATTR_LL_STATS_WMM_AC_* 2520 */ 2521 QCA_WLAN_VENDOR_ATTR_LL_STATS_WMM_INFO = 70, 2522 2523 /* Unsigned 8 bit value. Used by the driver; if set to 1, it indicates 2524 * that more stats, e.g., peers or radio, are to follow in the next 2525 * QCA_NL80211_VENDOR_SUBCMD_LL_STATS_*_RESULTS event. 2526 * Otherwise, it is set to 0. 2527 */ 2528 QCA_WLAN_VENDOR_ATTR_LL_STATS_RESULTS_MORE_DATA = 71, 2529 2530 /* Unsigned 64 bit value */ 2531 QCA_WLAN_VENDOR_ATTR_LL_STATS_IFACE_AVERAGE_TSF_OFFSET = 72, 2532 2533 /* Unsigned 32 bit value */ 2534 QCA_WLAN_VENDOR_ATTR_LL_STATS_IFACE_LEAKY_AP_DETECTED = 73, 2535 2536 /* Unsigned 32 bit value */ 2537 QCA_WLAN_VENDOR_ATTR_LL_STATS_IFACE_LEAKY_AP_AVG_NUM_FRAMES_LEAKED = 74, 2538 2539 /* Unsigned 32 bit value */ 2540 QCA_WLAN_VENDOR_ATTR_LL_STATS_IFACE_LEAKY_AP_GUARD_TIME = 75, 2541 2542 /* Unsigned 32 bit value */ 2543 QCA_WLAN_VENDOR_ATTR_LL_STATS_TYPE = 76, 2544 2545 /* Unsigned 32 bit value */ 2546 QCA_WLAN_VENDOR_ATTR_LL_STATS_RADIO_NUM_TX_LEVELS = 77, 2547 2548 /* Number of msecs the radio spent in transmitting for each power level 2549 */ 2550 QCA_WLAN_VENDOR_ATTR_LL_STATS_RADIO_TX_TIME_PER_LEVEL = 78, 2551 2552 /* Unsigned 32 bit value */ 2553 QCA_WLAN_VENDOR_ATTR_LL_STATS_IFACE_RTS_SUCC_CNT = 79, 2554 /* Unsigned 32 bit value */ 2555 QCA_WLAN_VENDOR_ATTR_LL_STATS_IFACE_RTS_FAIL_CNT = 80, 2556 /* Unsigned 32 bit value */ 2557 QCA_WLAN_VENDOR_ATTR_LL_STATS_IFACE_PPDU_SUCC_CNT = 81, 2558 /* Unsigned 32 bit value */ 2559 QCA_WLAN_VENDOR_ATTR_LL_STATS_IFACE_PPDU_FAIL_CNT = 82, 2560 2561 /* keep last */ 2562 QCA_WLAN_VENDOR_ATTR_LL_STATS_AFTER_LAST, 2563 QCA_WLAN_VENDOR_ATTR_LL_STATS_MAX = 2564 QCA_WLAN_VENDOR_ATTR_LL_STATS_AFTER_LAST - 1, 2565 }; 2566 2567 enum qca_wlan_vendor_attr_ll_stats_type 2568 { 2569 QCA_NL80211_VENDOR_SUBCMD_LL_STATS_TYPE_INVALID = 0, 2570 QCA_NL80211_VENDOR_SUBCMD_LL_STATS_TYPE_RADIO = 1, 2571 QCA_NL80211_VENDOR_SUBCMD_LL_STATS_TYPE_IFACE = 2, 2572 QCA_NL80211_VENDOR_SUBCMD_LL_STATS_TYPE_PEERS = 3, 2573 2574 /* keep last */ 2575 QCA_NL80211_VENDOR_SUBCMD_LL_STATS_TYPE_AFTER_LAST, 2576 QCA_NL80211_VENDOR_SUBCMD_LL_STATS_TYPE_MAX = 2577 QCA_NL80211_VENDOR_SUBCMD_LL_STATS_TYPE_AFTER_LAST - 1, 2578 }; 2579 2580 /** 2581 * enum qca_wlan_vendor_attr_tdls_configuration - Attributes for 2582 * TDLS configuration to the host driver. 2583 * 2584 * @QCA_WLAN_VENDOR_ATTR_TDLS_CONFIG_TRIGGER_MODE: Configure the TDLS trigger 2585 * mode in the host driver. enum qca_wlan_vendor_tdls_trigger_mode 2586 * represents the different TDLS trigger modes. 2587 * @QCA_WLAN_VENDOR_ATTR_TDLS_CONFIG_TX_STATS_PERIOD: Duration (u32) within 2588 * which QCA_WLAN_VENDOR_ATTR_TDLS_CONFIG_TX_THRESHOLD number 2589 * of packets shall meet the criteria for implicit TDLS setup. 2590 * @QCA_WLAN_VENDOR_ATTR_TDLS_CONFIG_TX_THRESHOLD: Number (u32) of Tx/Rx packets 2591 * within a duration QCA_WLAN_VENDOR_ATTR_TDLS_CONFIG_TX_STATS_PERIOD 2592 * to initiate a TDLS setup. 2593 * @QCA_WLAN_VENDOR_ATTR_TDLS_CONFIG_DISCOVERY_PERIOD: Time (u32) to initiate 2594 * a TDLS Discovery to the peer. 2595 * @QCA_WLAN_VENDOR_ATTR_TDLS_CONFIG_MAX_DISCOVERY_ATTEMPT: Max number (u32) of 2596 * discovery attempts to know the TDLS capability of the peer. A peer is 2597 * marked as TDLS not capable if there is no response for all the attempts. 2598 * @QCA_WLAN_VENDOR_ATTR_TDLS_CONFIG_IDLE_TIMEOUT: Represents a duration (u32) 2599 * within which QCA_WLAN_VENDOR_ATTR_TDLS_CONFIG_IDLE_PACKET_THRESHOLD 2600 * number of TX / RX frames meet the criteria for TDLS teardown. 2601 * @QCA_WLAN_VENDOR_ATTR_TDLS_CONFIG_IDLE_PACKET_THRESHOLD: Minimum number (u32) 2602 * of Tx/Rx packets within a duration 2603 * QCA_WLAN_VENDOR_ATTR_TDLS_CONFIG_IDLE_TIMEOUT to tear down a TDLS link. 2604 * @QCA_WLAN_VENDOR_ATTR_TDLS_CONFIG_SETUP_RSSI_THRESHOLD: Threshold 2605 * corresponding to the RSSI of the peer below which a TDLS setup is 2606 * triggered. 2607 * @QCA_WLAN_VENDOR_ATTR_TDLS_CONFIG_TEARDOWN_RSSI_THRESHOLD: Threshold 2608 * corresponding to the RSSI of the peer above which a TDLS teardown is 2609 * triggered. 2610 */ 2611 enum qca_wlan_vendor_attr_tdls_configuration { 2612 QCA_WLAN_VENDOR_ATTR_TDLS_CONFIG_INVALID = 0, 2613 QCA_WLAN_VENDOR_ATTR_TDLS_CONFIG_TRIGGER_MODE = 1, 2614 2615 /* Attributes configuring the TDLS Implicit Trigger */ 2616 QCA_WLAN_VENDOR_ATTR_TDLS_CONFIG_TX_STATS_PERIOD = 2, 2617 QCA_WLAN_VENDOR_ATTR_TDLS_CONFIG_TX_THRESHOLD = 3, 2618 QCA_WLAN_VENDOR_ATTR_TDLS_CONFIG_DISCOVERY_PERIOD = 4, 2619 QCA_WLAN_VENDOR_ATTR_TDLS_CONFIG_MAX_DISCOVERY_ATTEMPT = 5, 2620 QCA_WLAN_VENDOR_ATTR_TDLS_CONFIG_IDLE_TIMEOUT = 6, 2621 QCA_WLAN_VENDOR_ATTR_TDLS_CONFIG_IDLE_PACKET_THRESHOLD = 7, 2622 QCA_WLAN_VENDOR_ATTR_TDLS_CONFIG_SETUP_RSSI_THRESHOLD = 8, 2623 QCA_WLAN_VENDOR_ATTR_TDLS_CONFIG_TEARDOWN_RSSI_THRESHOLD = 9, 2624 2625 /* keep last */ 2626 QCA_WLAN_VENDOR_ATTR_TDLS_CONFIG_AFTER_LAST, 2627 QCA_WLAN_VENDOR_ATTR_TDLS_CONFIG_MAX = 2628 QCA_WLAN_VENDOR_ATTR_TDLS_CONFIG_AFTER_LAST - 1 2629 }; 2630 2631 /** 2632 * enum qca_wlan_vendor_tdls_trigger_mode: Represents the TDLS trigger mode in 2633 * the driver 2634 * 2635 * The following are the different values for 2636 * QCA_WLAN_VENDOR_ATTR_TDLS_CONFIG_TRIGGER_MODE. 2637 * 2638 * @QCA_WLAN_VENDOR_TDLS_TRIGGER_MODE_EXPLICIT: The trigger to initiate/teardown 2639 * the TDLS connection to a respective peer comes from the user space. 2640 * wpa_supplicant provides the commands TDLS_SETUP, TDLS_TEARDOWN, 2641 * TDLS_DISCOVER to do this. 2642 * @QCA_WLAN_VENDOR_TDLS_TRIGGER_MODE_IMPLICIT: Host driver triggers this TDLS 2643 * setup/teardown to the eligible peer once the configured criteria 2644 * (such as TX/RX threshold, RSSI) is met. The attributes 2645 * in QCA_WLAN_VENDOR_ATTR_TDLS_CONFIG_IMPLICIT_PARAMS correspond to 2646 * the different configuration criteria for the TDLS trigger from the 2647 * host driver. 2648 * @QCA_WLAN_VENDOR_TDLS_TRIGGER_MODE_EXTERNAL: Enables the driver to trigger 2649 * the TDLS setup / teardown through the implicit mode only to the 2650 * configured MAC addresses (wpa_supplicant, with tdls_external_control=1, 2651 * configures the MAC address through TDLS_SETUP / TDLS_TEARDOWN commands). 2652 * External mode works on top of the implicit mode. Thus the host driver 2653 * is expected to configure in TDLS Implicit mode too to operate in 2654 * External mode. 2655 * Configuring External mode alone without Implicit mode is invalid. 2656 * 2657 * All the above implementations work as expected only when the host driver 2658 * advertises the capability WPA_DRIVER_FLAGS_TDLS_EXTERNAL_SETUP - representing 2659 * that the TDLS message exchange is not internal to the host driver, but 2660 * depends on wpa_supplicant to do the message exchange. 2661 */ 2662 enum qca_wlan_vendor_tdls_trigger_mode { 2663 QCA_WLAN_VENDOR_TDLS_TRIGGER_MODE_EXPLICIT = 1 << 0, 2664 QCA_WLAN_VENDOR_TDLS_TRIGGER_MODE_IMPLICIT = 1 << 1, 2665 QCA_WLAN_VENDOR_TDLS_TRIGGER_MODE_EXTERNAL = 1 << 2, 2666 }; 2667 2668 /** 2669 * enum qca_vendor_attr_sar_limits_selections - Source of SAR power limits 2670 * @QCA_WLAN_VENDOR_ATTR_SAR_LIMITS_SELECT_BDF0: Select SAR profile #0 2671 * that is hard-coded in the Board Data File (BDF). 2672 * @QCA_WLAN_VENDOR_ATTR_SAR_LIMITS_SELECT_BDF1: Select SAR profile #1 2673 * that is hard-coded in the Board Data File (BDF). 2674 * @QCA_WLAN_VENDOR_ATTR_SAR_LIMITS_SELECT_BDF2: Select SAR profile #2 2675 * that is hard-coded in the Board Data File (BDF). 2676 * @QCA_WLAN_VENDOR_ATTR_SAR_LIMITS_SELECT_BDF3: Select SAR profile #3 2677 * that is hard-coded in the Board Data File (BDF). 2678 * @QCA_WLAN_VENDOR_ATTR_SAR_LIMITS_SELECT_BDF4: Select SAR profile #4 2679 * that is hard-coded in the Board Data File (BDF). 2680 * @QCA_WLAN_VENDOR_ATTR_SAR_LIMITS_SELECT_NONE: Do not select any 2681 * source of SAR power limits, thereby disabling the SAR power 2682 * limit feature. 2683 * @QCA_WLAN_VENDOR_ATTR_SAR_LIMITS_SELECT_USER: Select the SAR power 2684 * limits configured by %QCA_NL80211_VENDOR_SUBCMD_SET_SAR. 2685 * 2686 * This enumerates the valid set of values that may be supplied for 2687 * attribute %QCA_WLAN_VENDOR_ATTR_SAR_LIMITS_SELECT in an instance of 2688 * the %QCA_NL80211_VENDOR_SUBCMD_SET_SAR_LIMITS vendor command. 2689 */ 2690 enum qca_vendor_attr_sar_limits_selections { 2691 QCA_WLAN_VENDOR_ATTR_SAR_LIMITS_SELECT_BDF0 = 0, 2692 QCA_WLAN_VENDOR_ATTR_SAR_LIMITS_SELECT_BDF1 = 1, 2693 QCA_WLAN_VENDOR_ATTR_SAR_LIMITS_SELECT_BDF2 = 2, 2694 QCA_WLAN_VENDOR_ATTR_SAR_LIMITS_SELECT_BDF3 = 3, 2695 QCA_WLAN_VENDOR_ATTR_SAR_LIMITS_SELECT_BDF4 = 4, 2696 QCA_WLAN_VENDOR_ATTR_SAR_LIMITS_SELECT_NONE = 5, 2697 QCA_WLAN_VENDOR_ATTR_SAR_LIMITS_SELECT_USER = 6, 2698 }; 2699 2700 /** 2701 * enum qca_vendor_attr_sar_limits_spec_modulations - 2702 * SAR limits specification modulation 2703 * @QCA_WLAN_VENDOR_ATTR_SAR_LIMITS_SPEC_MODULATION_CCK - 2704 * CCK modulation 2705 * @QCA_WLAN_VENDOR_ATTR_SAR_LIMITS_SPEC_MODULATION_OFDM - 2706 * OFDM modulation 2707 * 2708 * This enumerates the valid set of values that may be supplied for 2709 * attribute %QCA_WLAN_VENDOR_ATTR_SAR_LIMITS_SPEC_MODULATION in an 2710 * instance of attribute %QCA_WLAN_VENDOR_ATTR_SAR_LIMITS_SPEC in an 2711 * instance of the %QCA_NL80211_VENDOR_SUBCMD_SET_SAR_LIMITS vendor 2712 * command. 2713 */ 2714 enum qca_vendor_attr_sar_limits_spec_modulations { 2715 QCA_WLAN_VENDOR_ATTR_SAR_LIMITS_SPEC_MODULATION_CCK = 0, 2716 QCA_WLAN_VENDOR_ATTR_SAR_LIMITS_SPEC_MODULATION_OFDM = 1, 2717 }; 2718 2719 /** 2720 * enum qca_vendor_attr_sar_limits - Attributes for SAR power limits 2721 * 2722 * @QCA_WLAN_VENDOR_ATTR_SAR_LIMITS_SAR_ENABLE: Optional (u32) value to 2723 * select which SAR power limit table should be used. Valid 2724 * values are enumerated in enum 2725 * %qca_vendor_attr_sar_limits_selections. The existing SAR 2726 * power limit selection is unchanged if this attribute is not 2727 * present. 2728 * 2729 * @QCA_WLAN_VENDOR_ATTR_SAR_LIMITS_NUM_SPECS: Optional (u32) value 2730 * which specifies the number of SAR power limit specifications 2731 * which will follow. 2732 * 2733 * @QCA_WLAN_VENDOR_ATTR_SAR_LIMITS_SPEC: Nested array of SAR power 2734 * limit specifications. The number of specifications is 2735 * specified by @QCA_WLAN_VENDOR_ATTR_SAR_LIMITS_NUM_SPECS. Each 2736 * specification contains a set of 2737 * QCA_WLAN_VENDOR_ATTR_SAR_LIMITS_SPEC_* attributes. A 2738 * specification is uniquely identified by the attributes 2739 * %QCA_WLAN_VENDOR_ATTR_SAR_LIMITS_SPEC_BAND, 2740 * %QCA_WLAN_VENDOR_ATTR_SAR_LIMITS_SPEC_CHAIN, and 2741 * %QCA_WLAN_VENDOR_ATTR_SAR_LIMITS_SPEC_MODULATION and always 2742 * contains as a payload the attribute 2743 * %QCA_WLAN_VENDOR_ATTR_SAR_LIMITS_SPEC_POWER_LIMIT. 2744 * 2745 * @QCA_WLAN_VENDOR_ATTR_SAR_LIMITS_SPEC_BAND: Optional (u32) value to 2746 * indicate for which band this specification applies. Valid 2747 * values are enumerated in enum %nl80211_band (although not all 2748 * bands may be supported by a given device). If the attribute is 2749 * not supplied then the specification will be applied to all 2750 * supported bands. 2751 * 2752 * @QCA_WLAN_VENDOR_ATTR_SAR_LIMITS_SPEC_CHAIN: Optional (u32) value 2753 * to indicate for which antenna chain this specification 2754 * applies, i.e. 1 for chain 1, 2 for chain 2, etc. If the 2755 * attribute is not supplied then the specification will be 2756 * applied to all chains. 2757 * 2758 * @QCA_WLAN_VENDOR_ATTR_SAR_LIMITS_SPEC_MODULATION: Optional (u32) 2759 * value to indicate for which modulation scheme this 2760 * specification applies. Valid values are enumerated in enum 2761 * %qca_vendor_attr_sar_limits_spec_modulations. If the attribute 2762 * is not supplied then the specification will be applied to all 2763 * modulation schemes. 2764 * 2765 * @QCA_WLAN_VENDOR_ATTR_SAR_LIMITS_SPEC_POWER_LIMIT: Required (u32) 2766 * value to specify the actual power limit value in units of 0.5 2767 * dBm (i.e., a value of 11 represents 5.5 dBm). 2768 * 2769 * These attributes are used with %QCA_NL80211_VENDOR_SUBCMD_SET_SAR_LIMITS. 2770 */ 2771 enum qca_vendor_attr_sar_limits { 2772 QCA_WLAN_VENDOR_ATTR_SAR_LIMITS_INVALID = 0, 2773 QCA_WLAN_VENDOR_ATTR_SAR_LIMITS_SAR_ENABLE = 1, 2774 QCA_WLAN_VENDOR_ATTR_SAR_LIMITS_NUM_SPECS = 2, 2775 QCA_WLAN_VENDOR_ATTR_SAR_LIMITS_SPEC = 3, 2776 QCA_WLAN_VENDOR_ATTR_SAR_LIMITS_SPEC_BAND = 4, 2777 QCA_WLAN_VENDOR_ATTR_SAR_LIMITS_SPEC_CHAIN = 5, 2778 QCA_WLAN_VENDOR_ATTR_SAR_LIMITS_SPEC_MODULATION = 6, 2779 QCA_WLAN_VENDOR_ATTR_SAR_LIMITS_SPEC_POWER_LIMIT = 7, 2780 2781 QCA_WLAN_VENDOR_ATTR_SAR_LIMITS_AFTER_LAST, 2782 QCA_WLAN_VENDOR_ATTR_SAR_LIMITS_MAX = 2783 QCA_WLAN_VENDOR_ATTR_SAR_LIMITS_AFTER_LAST - 1 2784 }; 2785 2786 /** 2787 * enum qca_wlan_vendor_attr_get_wifi_info: Attributes for data used by 2788 * QCA_NL80211_VENDOR_SUBCMD_GET_WIFI_INFO sub command. 2789 */ 2790 enum qca_wlan_vendor_attr_get_wifi_info { 2791 QCA_WLAN_VENDOR_ATTR_WIFI_INFO_GET_INVALID = 0, 2792 QCA_WLAN_VENDOR_ATTR_WIFI_INFO_DRIVER_VERSION = 1, 2793 QCA_WLAN_VENDOR_ATTR_WIFI_INFO_FIRMWARE_VERSION = 2, 2794 2795 /* keep last */ 2796 QCA_WLAN_VENDOR_ATTR_WIFI_INFO_GET_AFTER_LAST, 2797 QCA_WLAN_VENDOR_ATTR_WIFI_INFO_GET_MAX = 2798 QCA_WLAN_VENDOR_ATTR_WIFI_INFO_GET_AFTER_LAST - 1, 2799 }; 2800 2801 /* 2802 * enum qca_wlan_vendor_attr_wifi_logger_start: Attributes for data used by 2803 * QCA_NL80211_VENDOR_SUBCMD_WIFI_LOGGER_START sub command. 2804 */ 2805 enum qca_wlan_vendor_attr_wifi_logger_start { 2806 QCA_WLAN_VENDOR_ATTR_WIFI_LOGGER_START_INVALID = 0, 2807 QCA_WLAN_VENDOR_ATTR_WIFI_LOGGER_RING_ID = 1, 2808 QCA_WLAN_VENDOR_ATTR_WIFI_LOGGER_VERBOSE_LEVEL = 2, 2809 QCA_WLAN_VENDOR_ATTR_WIFI_LOGGER_FLAGS = 3, 2810 2811 /* keep last */ 2812 QCA_WLAN_VENDOR_ATTR_WIFI_LOGGER_START_AFTER_LAST, 2813 QCA_WLAN_VENDOR_ATTR_WIFI_LOGGER_START_GET_MAX = 2814 QCA_WLAN_VENDOR_ATTR_WIFI_LOGGER_START_AFTER_LAST - 1, 2815 }; 2816 2817 enum qca_wlan_vendor_attr_logger_results { 2818 QCA_WLAN_VENDOR_ATTR_LOGGER_RESULTS_INVALID = 0, 2819 2820 /* Unsigned 32-bit value; must match the request Id supplied by 2821 * Wi-Fi HAL in the corresponding subcmd NL msg. 2822 */ 2823 QCA_WLAN_VENDOR_ATTR_LOGGER_RESULTS_REQUEST_ID = 1, 2824 2825 /* Unsigned 32-bit value; used to indicate the size of memory 2826 * dump to be allocated. 2827 */ 2828 QCA_WLAN_VENDOR_ATTR_LOGGER_RESULTS_MEMDUMP_SIZE = 2, 2829 2830 /* keep last */ 2831 QCA_WLAN_VENDOR_ATTR_LOGGER_RESULTS_AFTER_LAST, 2832 QCA_WLAN_VENDOR_ATTR_LOGGER_RESULTS_MAX = 2833 QCA_WLAN_VENDOR_ATTR_LOGGER_RESULTS_AFTER_LAST - 1, 2834 }; 2835 2836 enum qca_wlan_vendor_attr_roaming_config_params { 2837 QCA_WLAN_VENDOR_ATTR_ROAMING_PARAM_INVALID = 0, 2838 2839 QCA_WLAN_VENDOR_ATTR_ROAMING_SUBCMD = 1, 2840 QCA_WLAN_VENDOR_ATTR_ROAMING_REQ_ID = 2, 2841 2842 /* Attributes for wifi_set_ssid_white_list */ 2843 QCA_WLAN_VENDOR_ATTR_ROAMING_PARAM_WHITE_LIST_SSID_NUM_NETWORKS = 3, 2844 QCA_WLAN_VENDOR_ATTR_ROAMING_PARAM_WHITE_LIST_SSID_LIST = 4, 2845 QCA_WLAN_VENDOR_ATTR_ROAMING_PARAM_WHITE_LIST_SSID = 5, 2846 2847 /* Attributes for set_roam_params */ 2848 QCA_WLAN_VENDOR_ATTR_ROAMING_PARAM_A_BAND_BOOST_THRESHOLD = 6, 2849 QCA_WLAN_VENDOR_ATTR_ROAMING_PARAM_A_BAND_PENALTY_THRESHOLD = 7, 2850 QCA_WLAN_VENDOR_ATTR_ROAMING_PARAM_A_BAND_BOOST_FACTOR = 8, 2851 QCA_WLAN_VENDOR_ATTR_ROAMING_PARAM_A_BAND_PENALTY_FACTOR = 9, 2852 QCA_WLAN_VENDOR_ATTR_ROAMING_PARAM_A_BAND_MAX_BOOST = 10, 2853 QCA_WLAN_VENDOR_ATTR_ROAMING_PARAM_LAZY_ROAM_HISTERESYS = 11, 2854 QCA_WLAN_VENDOR_ATTR_ROAMING_PARAM_ALERT_ROAM_RSSI_TRIGGER = 12, 2855 2856 /* Attribute for set_lazy_roam */ 2857 QCA_WLAN_VENDOR_ATTR_ROAMING_PARAM_SET_LAZY_ROAM_ENABLE = 13, 2858 2859 /* Attribute for set_lazy_roam with preferences */ 2860 QCA_WLAN_VENDOR_ATTR_ROAMING_PARAM_SET_BSSID_PREFS = 14, 2861 QCA_WLAN_VENDOR_ATTR_ROAMING_PARAM_SET_LAZY_ROAM_NUM_BSSID = 15, 2862 QCA_WLAN_VENDOR_ATTR_ROAMING_PARAM_SET_LAZY_ROAM_BSSID = 16, 2863 QCA_WLAN_VENDOR_ATTR_ROAMING_PARAM_SET_LAZY_ROAM_RSSI_MODIFIER = 17, 2864 2865 /* Attribute for set_blacklist bssid params */ 2866 QCA_WLAN_VENDOR_ATTR_ROAMING_PARAM_SET_BSSID_PARAMS = 18, 2867 QCA_WLAN_VENDOR_ATTR_ROAMING_PARAM_SET_BSSID_PARAMS_NUM_BSSID = 19, 2868 QCA_WLAN_VENDOR_ATTR_ROAMING_PARAM_SET_BSSID_PARAMS_BSSID = 20, 2869 2870 /* keep last */ 2871 QCA_WLAN_VENDOR_ATTR_ROAMING_PARAM_AFTER_LAST, 2872 QCA_WLAN_VENDOR_ATTR_ROAMING_PARAM_MAX = 2873 QCA_WLAN_VENDOR_ATTR_ROAMING_PARAM_AFTER_LAST - 1, 2874 }; 2875 2876 /* 2877 * enum qca_wlan_vendor_attr_roam_subcmd: Attributes for data used by 2878 * QCA_NL80211_VENDOR_SUBCMD_ROAM sub command. 2879 */ 2880 enum qca_wlan_vendor_attr_roam_subcmd { 2881 QCA_WLAN_VENDOR_ATTR_ROAM_SUBCMD_INVALID = 0, 2882 QCA_WLAN_VENDOR_ATTR_ROAM_SUBCMD_SSID_WHITE_LIST = 1, 2883 QCA_WLAN_VENDOR_ATTR_ROAM_SUBCMD_SET_GSCAN_ROAM_PARAMS = 2, 2884 QCA_WLAN_VENDOR_ATTR_ROAM_SUBCMD_SET_LAZY_ROAM = 3, 2885 QCA_WLAN_VENDOR_ATTR_ROAM_SUBCMD_SET_BSSID_PREFS = 4, 2886 QCA_WLAN_VENDOR_ATTR_ROAM_SUBCMD_SET_BSSID_PARAMS = 5, 2887 QCA_WLAN_VENDOR_ATTR_ROAM_SUBCMD_SET_BLACKLIST_BSSID = 6, 2888 2889 /* keep last */ 2890 QCA_WLAN_VENDOR_ATTR_ROAM_SUBCMD_AFTER_LAST, 2891 QCA_WLAN_VENDOR_ATTR_ROAM_SUBCMD_MAX = 2892 QCA_WLAN_VENDOR_ATTR_ROAM_SUBCMD_AFTER_LAST - 1, 2893 }; 2894 2895 enum qca_wlan_vendor_attr_gscan_config_params { 2896 QCA_WLAN_VENDOR_ATTR_GSCAN_SUBCMD_CONFIG_PARAM_INVALID = 0, 2897 2898 /* Unsigned 32-bit value */ 2899 QCA_WLAN_VENDOR_ATTR_GSCAN_SUBCMD_CONFIG_PARAM_REQUEST_ID = 1, 2900 2901 /* Attributes for data used by 2902 * QCA_NL80211_VENDOR_SUBCMD_GSCAN_GET_VALID_CHANNELS sub command. 2903 */ 2904 /* Unsigned 32-bit value */ 2905 QCA_WLAN_VENDOR_ATTR_GSCAN_GET_VALID_CHANNELS_CONFIG_PARAM_WIFI_BAND 2906 = 2, 2907 /* Unsigned 32-bit value */ 2908 QCA_WLAN_VENDOR_ATTR_GSCAN_GET_VALID_CHANNELS_CONFIG_PARAM_MAX_CHANNELS 2909 = 3, 2910 2911 /* Attributes for input params used by 2912 * QCA_NL80211_VENDOR_SUBCMD_GSCAN_START sub command. 2913 */ 2914 2915 /* Unsigned 32-bit value; channel frequency */ 2916 QCA_WLAN_VENDOR_ATTR_GSCAN_CHANNEL_SPEC_CHANNEL = 4, 2917 /* Unsigned 32-bit value; dwell time in ms. */ 2918 QCA_WLAN_VENDOR_ATTR_GSCAN_CHANNEL_SPEC_DWELL_TIME = 5, 2919 /* Unsigned 8-bit value; 0: active; 1: passive; N/A for DFS */ 2920 QCA_WLAN_VENDOR_ATTR_GSCAN_CHANNEL_SPEC_PASSIVE = 6, 2921 /* Unsigned 8-bit value; channel class */ 2922 QCA_WLAN_VENDOR_ATTR_GSCAN_CHANNEL_SPEC_CLASS = 7, 2923 2924 /* Unsigned 8-bit value; bucket index, 0 based */ 2925 QCA_WLAN_VENDOR_ATTR_GSCAN_BUCKET_SPEC_INDEX = 8, 2926 /* Unsigned 8-bit value; band. */ 2927 QCA_WLAN_VENDOR_ATTR_GSCAN_BUCKET_SPEC_BAND = 9, 2928 /* Unsigned 32-bit value; desired period, in ms. */ 2929 QCA_WLAN_VENDOR_ATTR_GSCAN_BUCKET_SPEC_PERIOD = 10, 2930 /* Unsigned 8-bit value; report events semantics. */ 2931 QCA_WLAN_VENDOR_ATTR_GSCAN_BUCKET_SPEC_REPORT_EVENTS = 11, 2932 /* Unsigned 32-bit value. Followed by a nested array of 2933 * GSCAN_CHANNEL_SPEC_* attributes. 2934 */ 2935 QCA_WLAN_VENDOR_ATTR_GSCAN_BUCKET_SPEC_NUM_CHANNEL_SPECS = 12, 2936 2937 /* Array of QCA_WLAN_VENDOR_ATTR_GSCAN_CHANNEL_SPEC_* attributes. 2938 * Array size: QCA_WLAN_VENDOR_ATTR_GSCAN_BUCKET_SPEC_NUM_CHANNEL_SPECS 2939 */ 2940 QCA_WLAN_VENDOR_ATTR_GSCAN_CHANNEL_SPEC = 13, 2941 2942 /* Unsigned 32-bit value; base timer period in ms. */ 2943 QCA_WLAN_VENDOR_ATTR_GSCAN_SCAN_CMD_PARAMS_BASE_PERIOD = 14, 2944 /* Unsigned 32-bit value; number of APs to store in each scan in the 2945 * BSSID/RSSI history buffer (keep the highest RSSI APs). 2946 */ 2947 QCA_WLAN_VENDOR_ATTR_GSCAN_SCAN_CMD_PARAMS_MAX_AP_PER_SCAN = 15, 2948 /* Unsigned 8-bit value; in %, when scan buffer is this much full, wake 2949 * up AP. 2950 */ 2951 QCA_WLAN_VENDOR_ATTR_GSCAN_SCAN_CMD_PARAMS_REPORT_THRESHOLD_PERCENT 2952 = 16, 2953 2954 /* Unsigned 8-bit value; number of scan bucket specs; followed by a 2955 * nested array of_GSCAN_BUCKET_SPEC_* attributes and values. The size 2956 * of the array is determined by NUM_BUCKETS. 2957 */ 2958 QCA_WLAN_VENDOR_ATTR_GSCAN_SCAN_CMD_PARAMS_NUM_BUCKETS = 17, 2959 2960 /* Array of QCA_WLAN_VENDOR_ATTR_GSCAN_BUCKET_SPEC_* attributes. 2961 * Array size: QCA_WLAN_VENDOR_ATTR_GSCAN_SCAN_CMD_PARAMS_NUM_BUCKETS 2962 */ 2963 QCA_WLAN_VENDOR_ATTR_GSCAN_BUCKET_SPEC = 18, 2964 2965 /* Unsigned 8-bit value */ 2966 QCA_WLAN_VENDOR_ATTR_GSCAN_GET_CACHED_SCAN_RESULTS_CONFIG_PARAM_FLUSH 2967 = 19, 2968 /* Unsigned 32-bit value; maximum number of results to be returned. */ 2969 QCA_WLAN_VENDOR_ATTR_GSCAN_GET_CACHED_SCAN_RESULTS_CONFIG_PARAM_MAX 2970 = 20, 2971 2972 /* An array of 6 x unsigned 8-bit value */ 2973 QCA_WLAN_VENDOR_ATTR_GSCAN_AP_THRESHOLD_PARAM_BSSID = 21, 2974 /* Signed 32-bit value */ 2975 QCA_WLAN_VENDOR_ATTR_GSCAN_AP_THRESHOLD_PARAM_RSSI_LOW = 22, 2976 /* Signed 32-bit value */ 2977 QCA_WLAN_VENDOR_ATTR_GSCAN_AP_THRESHOLD_PARAM_RSSI_HIGH = 23, 2978 /* Unsigned 32-bit value */ 2979 QCA_WLAN_VENDOR_ATTR_GSCAN_AP_THRESHOLD_PARAM_CHANNEL = 24, 2980 2981 /* Number of hotlist APs as unsigned 32-bit value, followed by a nested 2982 * array of AP_THRESHOLD_PARAM attributes and values. The size of the 2983 * array is determined by NUM_AP. 2984 */ 2985 QCA_WLAN_VENDOR_ATTR_GSCAN_BSSID_HOTLIST_PARAMS_NUM_AP = 25, 2986 2987 /* Array of QCA_WLAN_VENDOR_ATTR_GSCAN_AP_THRESHOLD_PARAM_* attributes. 2988 * Array size: QCA_WLAN_VENDOR_ATTR_GSCAN_BUCKET_SPEC_NUM_CHANNEL_SPECS 2989 */ 2990 QCA_WLAN_VENDOR_ATTR_GSCAN_AP_THRESHOLD_PARAM = 26, 2991 2992 /* Unsigned 32-bit value; number of samples for averaging RSSI. */ 2993 QCA_WLAN_VENDOR_ATTR_GSCAN_SIGNIFICANT_CHANGE_PARAMS_RSSI_SAMPLE_SIZE 2994 = 27, 2995 /* Unsigned 32-bit value; number of samples to confirm AP loss. */ 2996 QCA_WLAN_VENDOR_ATTR_GSCAN_SIGNIFICANT_CHANGE_PARAMS_LOST_AP_SAMPLE_SIZE 2997 = 28, 2998 /* Unsigned 32-bit value; number of APs breaching threshold. */ 2999 QCA_WLAN_VENDOR_ATTR_GSCAN_SIGNIFICANT_CHANGE_PARAMS_MIN_BREACHING = 29, 3000 /* Unsigned 32-bit value; number of APs. Followed by an array of 3001 * AP_THRESHOLD_PARAM attributes. Size of the array is NUM_AP. 3002 */ 3003 QCA_WLAN_VENDOR_ATTR_GSCAN_SIGNIFICANT_CHANGE_PARAMS_NUM_AP = 30, 3004 /* Unsigned 32-bit value; number of samples to confirm AP loss. */ 3005 QCA_WLAN_VENDOR_ATTR_GSCAN_BSSID_HOTLIST_PARAMS_LOST_AP_SAMPLE_SIZE 3006 = 31, 3007 /* Unsigned 32-bit value. If max_period is non zero or different than 3008 * period, then this bucket is an exponential backoff bucket. 3009 */ 3010 QCA_WLAN_VENDOR_ATTR_GSCAN_BUCKET_SPEC_MAX_PERIOD = 32, 3011 /* Unsigned 32-bit value. */ 3012 QCA_WLAN_VENDOR_ATTR_GSCAN_BUCKET_SPEC_BASE = 33, 3013 /* Unsigned 32-bit value. For exponential back off bucket, number of 3014 * scans to perform for a given period. 3015 */ 3016 QCA_WLAN_VENDOR_ATTR_GSCAN_BUCKET_SPEC_STEP_COUNT = 34, 3017 /* Unsigned 8-bit value; in number of scans, wake up AP after these 3018 * many scans. 3019 */ 3020 QCA_WLAN_VENDOR_ATTR_GSCAN_SCAN_CMD_PARAMS_REPORT_THRESHOLD_NUM_SCANS 3021 = 35, 3022 3023 /* Attributes for data used by 3024 * QCA_NL80211_VENDOR_SUBCMD_GSCAN_SET_SSID_HOTLIST sub command. 3025 */ 3026 /* Unsigned 3-2bit value; number of samples to confirm SSID loss. */ 3027 QCA_WLAN_VENDOR_ATTR_GSCAN_SSID_HOTLIST_PARAMS_LOST_SSID_SAMPLE_SIZE 3028 = 36, 3029 /* Number of hotlist SSIDs as unsigned 32-bit value, followed by a 3030 * nested array of SSID_THRESHOLD_PARAM_* attributes and values. The 3031 * size of the array is determined by NUM_SSID. 3032 */ 3033 QCA_WLAN_VENDOR_ATTR_GSCAN_SSID_HOTLIST_PARAMS_NUM_SSID = 37, 3034 /* Array of QCA_WLAN_VENDOR_ATTR_GSCAN_SSID_THRESHOLD_PARAM_* 3035 * attributes. 3036 * Array size: QCA_WLAN_VENDOR_ATTR_GSCAN_SSID_HOTLIST_PARAMS_NUM_SSID 3037 */ 3038 QCA_WLAN_VENDOR_ATTR_GSCAN_SSID_THRESHOLD_PARAM = 38, 3039 3040 /* An array of 33 x unsigned 8-bit value; NULL terminated SSID */ 3041 QCA_WLAN_VENDOR_ATTR_GSCAN_SSID_THRESHOLD_PARAM_SSID = 39, 3042 /* Unsigned 8-bit value */ 3043 QCA_WLAN_VENDOR_ATTR_GSCAN_SSID_THRESHOLD_PARAM_BAND = 40, 3044 /* Signed 32-bit value */ 3045 QCA_WLAN_VENDOR_ATTR_GSCAN_SSID_THRESHOLD_PARAM_RSSI_LOW = 41, 3046 /* Signed 32-bit value */ 3047 QCA_WLAN_VENDOR_ATTR_GSCAN_SSID_THRESHOLD_PARAM_RSSI_HIGH = 42, 3048 /* Unsigned 32-bit value; a bitmask with additional gscan config flag. 3049 */ 3050 QCA_WLAN_VENDOR_ATTR_GSCAN_CONFIGURATION_FLAGS = 43, 3051 3052 /* keep last */ 3053 QCA_WLAN_VENDOR_ATTR_GSCAN_SUBCMD_CONFIG_PARAM_AFTER_LAST, 3054 QCA_WLAN_VENDOR_ATTR_GSCAN_SUBCMD_CONFIG_PARAM_MAX = 3055 QCA_WLAN_VENDOR_ATTR_GSCAN_SUBCMD_CONFIG_PARAM_AFTER_LAST - 1, 3056 }; 3057 3058 enum qca_wlan_vendor_attr_gscan_results { 3059 QCA_WLAN_VENDOR_ATTR_GSCAN_RESULTS_INVALID = 0, 3060 3061 /* Unsigned 32-bit value; must match the request Id supplied by 3062 * Wi-Fi HAL in the corresponding subcmd NL msg. 3063 */ 3064 QCA_WLAN_VENDOR_ATTR_GSCAN_RESULTS_REQUEST_ID = 1, 3065 3066 /* Unsigned 32-bit value; used to indicate the status response from 3067 * firmware/driver for the vendor sub-command. 3068 */ 3069 QCA_WLAN_VENDOR_ATTR_GSCAN_STATUS = 2, 3070 3071 /* GSCAN Valid Channels attributes */ 3072 /* Unsigned 32bit value; followed by a nested array of CHANNELS. */ 3073 QCA_WLAN_VENDOR_ATTR_GSCAN_RESULTS_NUM_CHANNELS = 3, 3074 /* An array of NUM_CHANNELS x unsigned 32-bit value integers 3075 * representing channel numbers. 3076 */ 3077 QCA_WLAN_VENDOR_ATTR_GSCAN_RESULTS_CHANNELS = 4, 3078 3079 /* GSCAN Capabilities attributes */ 3080 /* Unsigned 32-bit value */ 3081 QCA_WLAN_VENDOR_ATTR_GSCAN_RESULTS_CAPABILITIES_MAX_SCAN_CACHE_SIZE = 5, 3082 /* Unsigned 32-bit value */ 3083 QCA_WLAN_VENDOR_ATTR_GSCAN_RESULTS_CAPABILITIES_MAX_SCAN_BUCKETS = 6, 3084 /* Unsigned 32-bit value */ 3085 QCA_WLAN_VENDOR_ATTR_GSCAN_RESULTS_CAPABILITIES_MAX_AP_CACHE_PER_SCAN 3086 = 7, 3087 /* Unsigned 32-bit value */ 3088 QCA_WLAN_VENDOR_ATTR_GSCAN_RESULTS_CAPABILITIES_MAX_RSSI_SAMPLE_SIZE 3089 = 8, 3090 /* Signed 32-bit value */ 3091 QCA_WLAN_VENDOR_ATTR_GSCAN_RESULTS_CAPABILITIES_MAX_SCAN_REPORTING_THRESHOLD 3092 = 9, 3093 /* Unsigned 32-bit value */ 3094 QCA_WLAN_VENDOR_ATTR_GSCAN_RESULTS_CAPABILITIES_MAX_HOTLIST_BSSIDS = 10, 3095 /* Unsigned 32-bit value */ 3096 QCA_WLAN_VENDOR_ATTR_GSCAN_RESULTS_CAPABILITIES_MAX_SIGNIFICANT_WIFI_CHANGE_APS 3097 = 11, 3098 /* Unsigned 32-bit value */ 3099 QCA_WLAN_VENDOR_ATTR_GSCAN_RESULTS_CAPABILITIES_MAX_BSSID_HISTORY_ENTRIES 3100 = 12, 3101 3102 /* GSCAN Attributes used with 3103 * QCA_NL80211_VENDOR_SUBCMD_GSCAN_SCAN_RESULTS_AVAILABLE sub-command. 3104 */ 3105 3106 /* Unsigned 32-bit value */ 3107 QCA_WLAN_VENDOR_ATTR_GSCAN_RESULTS_NUM_RESULTS_AVAILABLE = 13, 3108 3109 /* GSCAN attributes used with 3110 * QCA_NL80211_VENDOR_SUBCMD_GSCAN_FULL_SCAN_RESULT sub-command. 3111 */ 3112 3113 /* An array of NUM_RESULTS_AVAILABLE x 3114 * QCA_WLAN_VENDOR_ATTR_GSCAN_RESULTS_SCAN_RESULT_* 3115 */ 3116 QCA_WLAN_VENDOR_ATTR_GSCAN_RESULTS_LIST = 14, 3117 3118 /* Unsigned 64-bit value; age of sample at the time of retrieval */ 3119 QCA_WLAN_VENDOR_ATTR_GSCAN_RESULTS_SCAN_RESULT_TIME_STAMP = 15, 3120 /* 33 x unsigned 8-bit value; NULL terminated SSID */ 3121 QCA_WLAN_VENDOR_ATTR_GSCAN_RESULTS_SCAN_RESULT_SSID = 16, 3122 /* An array of 6 x unsigned 8-bit value */ 3123 QCA_WLAN_VENDOR_ATTR_GSCAN_RESULTS_SCAN_RESULT_BSSID = 17, 3124 /* Unsigned 32-bit value; channel frequency in MHz */ 3125 QCA_WLAN_VENDOR_ATTR_GSCAN_RESULTS_SCAN_RESULT_CHANNEL = 18, 3126 /* Signed 32-bit value */ 3127 QCA_WLAN_VENDOR_ATTR_GSCAN_RESULTS_SCAN_RESULT_RSSI = 19, 3128 /* Unsigned 32-bit value */ 3129 QCA_WLAN_VENDOR_ATTR_GSCAN_RESULTS_SCAN_RESULT_RTT = 20, 3130 /* Unsigned 32-bit value */ 3131 QCA_WLAN_VENDOR_ATTR_GSCAN_RESULTS_SCAN_RESULT_RTT_SD = 21, 3132 /* Unsigned 16-bit value */ 3133 QCA_WLAN_VENDOR_ATTR_GSCAN_RESULTS_SCAN_RESULT_BEACON_PERIOD = 22, 3134 /* Unsigned 16-bit value */ 3135 QCA_WLAN_VENDOR_ATTR_GSCAN_RESULTS_SCAN_RESULT_CAPABILITY = 23, 3136 /* Unsigned 32-bit value; size of the IE DATA blob */ 3137 QCA_WLAN_VENDOR_ATTR_GSCAN_RESULTS_SCAN_RESULT_IE_LENGTH = 24, 3138 /* An array of IE_LENGTH x unsigned 8-bit value; blob of all the 3139 * information elements found in the beacon; this data should be a 3140 * packed list of wifi_information_element objects, one after the 3141 * other. 3142 */ 3143 QCA_WLAN_VENDOR_ATTR_GSCAN_RESULTS_SCAN_RESULT_IE_DATA = 25, 3144 3145 /* Unsigned 8-bit value; set by driver to indicate more scan results are 3146 * available. 3147 */ 3148 QCA_WLAN_VENDOR_ATTR_GSCAN_RESULTS_SCAN_RESULT_MORE_DATA = 26, 3149 3150 /* GSCAN attributes for 3151 * QCA_NL80211_VENDOR_SUBCMD_GSCAN_SCAN_EVENT sub-command. 3152 */ 3153 /* Unsigned 8-bit value */ 3154 QCA_WLAN_VENDOR_ATTR_GSCAN_RESULTS_SCAN_EVENT_TYPE = 27, 3155 /* Unsigned 32-bit value */ 3156 QCA_WLAN_VENDOR_ATTR_GSCAN_RESULTS_SCAN_EVENT_STATUS = 28, 3157 3158 /* GSCAN attributes for 3159 * QCA_NL80211_VENDOR_SUBCMD_GSCAN_HOTLIST_AP_FOUND sub-command. 3160 */ 3161 /* Use attr QCA_WLAN_VENDOR_ATTR_GSCAN_RESULTS_NUM_RESULTS_AVAILABLE 3162 * to indicate number of results. 3163 * Also, use QCA_WLAN_VENDOR_ATTR_GSCAN_RESULTS_LIST to indicate the 3164 * list of results. 3165 */ 3166 3167 /* GSCAN attributes for 3168 * QCA_NL80211_VENDOR_SUBCMD_GSCAN_SIGNIFICANT_CHANGE sub-command. 3169 */ 3170 /* An array of 6 x unsigned 8-bit value */ 3171 QCA_WLAN_VENDOR_ATTR_GSCAN_RESULTS_SIGNIFICANT_CHANGE_RESULT_BSSID = 29, 3172 /* Unsigned 32-bit value */ 3173 QCA_WLAN_VENDOR_ATTR_GSCAN_RESULTS_SIGNIFICANT_CHANGE_RESULT_CHANNEL 3174 = 30, 3175 /* Unsigned 32-bit value. */ 3176 QCA_WLAN_VENDOR_ATTR_GSCAN_RESULTS_SIGNIFICANT_CHANGE_RESULT_NUM_RSSI 3177 = 31, 3178 /* A nested array of signed 32-bit RSSI values. Size of the array is 3179 * determined by (NUM_RSSI of SIGNIFICANT_CHANGE_RESULT_NUM_RSSI. 3180 */ 3181 QCA_WLAN_VENDOR_ATTR_GSCAN_RESULTS_SIGNIFICANT_CHANGE_RESULT_RSSI_LIST 3182 = 32, 3183 3184 /* GSCAN attributes used with 3185 * QCA_NL80211_VENDOR_SUBCMD_GSCAN_GET_CACHED_RESULTS sub-command. 3186 */ 3187 /* Use attr QCA_WLAN_VENDOR_ATTR_GSCAN_RESULTS_NUM_RESULTS_AVAILABLE 3188 * to indicate number of gscan cached results returned. 3189 * Also, use QCA_WLAN_VENDOR_ATTR_GSCAN_CACHED_RESULTS_LIST to indicate 3190 * the list of gscan cached results. 3191 */ 3192 3193 /* An array of NUM_RESULTS_AVAILABLE x 3194 * QCA_NL80211_VENDOR_ATTR_GSCAN_CACHED_RESULTS_* 3195 */ 3196 QCA_WLAN_VENDOR_ATTR_GSCAN_CACHED_RESULTS_LIST = 33, 3197 /* Unsigned 32-bit value; a unique identifier for the scan unit. */ 3198 QCA_WLAN_VENDOR_ATTR_GSCAN_CACHED_RESULTS_SCAN_ID = 34, 3199 /* Unsigned 32-bit value; a bitmask w/additional information about scan. 3200 */ 3201 QCA_WLAN_VENDOR_ATTR_GSCAN_CACHED_RESULTS_FLAGS = 35, 3202 /* Use attr QCA_WLAN_VENDOR_ATTR_GSCAN_RESULTS_NUM_RESULTS_AVAILABLE 3203 * to indicate number of wifi scan results/bssids retrieved by the scan. 3204 * Also, use QCA_WLAN_VENDOR_ATTR_GSCAN_RESULTS_LIST to indicate the 3205 * list of wifi scan results returned for each cached result block. 3206 */ 3207 3208 /* GSCAN attributes for 3209 * QCA_NL80211_VENDOR_SUBCMD_PNO_NETWORK_FOUND sub-command. 3210 */ 3211 /* Use QCA_WLAN_VENDOR_ATTR_GSCAN_RESULTS_NUM_RESULTS_AVAILABLE for 3212 * number of results. 3213 * Use QCA_WLAN_VENDOR_ATTR_GSCAN_RESULTS_LIST to indicate the nested 3214 * list of wifi scan results returned for each 3215 * wifi_passpoint_match_result block. 3216 * Array size: QCA_WLAN_VENDOR_ATTR_GSCAN_RESULTS_NUM_RESULTS_AVAILABLE. 3217 */ 3218 3219 /* GSCAN attributes for 3220 * QCA_NL80211_VENDOR_SUBCMD_PNO_PASSPOINT_NETWORK_FOUND sub-command. 3221 */ 3222 /* Unsigned 32-bit value */ 3223 QCA_WLAN_VENDOR_ATTR_GSCAN_PNO_RESULTS_PASSPOINT_NETWORK_FOUND_NUM_MATCHES 3224 = 36, 3225 /* A nested array of 3226 * QCA_WLAN_VENDOR_ATTR_GSCAN_PNO_RESULTS_PASSPOINT_MATCH_* 3227 * attributes. Array size = 3228 * *_ATTR_GSCAN_PNO_RESULTS_PASSPOINT_NETWORK_FOUND_NUM_MATCHES. 3229 */ 3230 QCA_WLAN_VENDOR_ATTR_GSCAN_PNO_RESULTS_PASSPOINT_MATCH_RESULT_LIST = 37, 3231 3232 /* Unsigned 32-bit value; network block id for the matched network */ 3233 QCA_WLAN_VENDOR_ATTR_GSCAN_PNO_RESULTS_PASSPOINT_MATCH_ID = 38, 3234 /* Use QCA_WLAN_VENDOR_ATTR_GSCAN_RESULTS_LIST to indicate the nested 3235 * list of wifi scan results returned for each 3236 * wifi_passpoint_match_result block. 3237 */ 3238 /* Unsigned 32-bit value */ 3239 QCA_WLAN_VENDOR_ATTR_GSCAN_PNO_RESULTS_PASSPOINT_MATCH_ANQP_LEN = 39, 3240 /* An array size of PASSPOINT_MATCH_ANQP_LEN of unsigned 8-bit values; 3241 * ANQP data in the information_element format. 3242 */ 3243 QCA_WLAN_VENDOR_ATTR_GSCAN_PNO_RESULTS_PASSPOINT_MATCH_ANQP = 40, 3244 3245 /* Unsigned 32-bit value; a GSCAN Capabilities attribute. */ 3246 QCA_WLAN_VENDOR_ATTR_GSCAN_RESULTS_CAPABILITIES_MAX_HOTLIST_SSIDS = 41, 3247 /* Unsigned 32-bit value; a GSCAN Capabilities attribute. */ 3248 QCA_WLAN_VENDOR_ATTR_GSCAN_RESULTS_CAPABILITIES_MAX_NUM_EPNO_NETS = 42, 3249 /* Unsigned 32-bit value; a GSCAN Capabilities attribute. */ 3250 QCA_WLAN_VENDOR_ATTR_GSCAN_RESULTS_CAPABILITIES_MAX_NUM_EPNO_NETS_BY_SSID 3251 = 43, 3252 /* Unsigned 32-bit value; a GSCAN Capabilities attribute. */ 3253 QCA_WLAN_VENDOR_ATTR_GSCAN_RESULTS_CAPABILITIES_MAX_NUM_WHITELISTED_SSID 3254 = 44, 3255 3256 QCA_WLAN_VENDOR_ATTR_GSCAN_RESULTS_BUCKETS_SCANNED = 45, 3257 3258 /* keep last */ 3259 QCA_WLAN_VENDOR_ATTR_GSCAN_RESULTS_AFTER_LAST, 3260 QCA_WLAN_VENDOR_ATTR_GSCAN_RESULTS_MAX = 3261 QCA_WLAN_VENDOR_ATTR_GSCAN_RESULTS_AFTER_LAST - 1, 3262 }; 3263 3264 enum qca_wlan_vendor_attr_pno_config_params { 3265 QCA_WLAN_VENDOR_ATTR_PNO_INVALID = 0, 3266 /* Attributes for data used by 3267 * QCA_NL80211_VENDOR_SUBCMD_PNO_SET_PASSPOINT_LIST sub command. 3268 */ 3269 /* Unsigned 32-bit value */ 3270 QCA_WLAN_VENDOR_ATTR_PNO_PASSPOINT_LIST_PARAM_NUM = 1, 3271 /* Array of nested QCA_WLAN_VENDOR_ATTR_PNO_PASSPOINT_NETWORK_PARAM_* 3272 * attributes. Array size = 3273 * QCA_WLAN_VENDOR_ATTR_PNO_PASSPOINT_LIST_PARAM_NUM. 3274 */ 3275 QCA_WLAN_VENDOR_ATTR_PNO_PASSPOINT_LIST_PARAM_NETWORK_ARRAY = 2, 3276 3277 /* Unsigned 32-bit value */ 3278 QCA_WLAN_VENDOR_ATTR_PNO_PASSPOINT_NETWORK_PARAM_ID = 3, 3279 /* An array of 256 x unsigned 8-bit value; NULL terminated UTF-8 encoded 3280 * realm, 0 if unspecified. 3281 */ 3282 QCA_WLAN_VENDOR_ATTR_PNO_PASSPOINT_NETWORK_PARAM_REALM = 4, 3283 /* An array of 16 x unsigned 32-bit value; roaming consortium ids to 3284 * match, 0 if unspecified. 3285 */ 3286 QCA_WLAN_VENDOR_ATTR_PNO_PASSPOINT_NETWORK_PARAM_ROAM_CNSRTM_ID = 5, 3287 /* An array of 6 x unsigned 8-bit value; MCC/MNC combination, 0s if 3288 * unspecified. 3289 */ 3290 QCA_WLAN_VENDOR_ATTR_PNO_PASSPOINT_NETWORK_PARAM_ROAM_PLMN = 6, 3291 3292 /* Attributes for data used by 3293 * QCA_NL80211_VENDOR_SUBCMD_PNO_SET_LIST sub command. 3294 */ 3295 /* Unsigned 32-bit value */ 3296 QCA_WLAN_VENDOR_ATTR_PNO_SET_LIST_PARAM_NUM_NETWORKS = 7, 3297 /* Array of nested 3298 * QCA_WLAN_VENDOR_ATTR_PNO_SET_LIST_PARAM_EPNO_NETWORK_* 3299 * attributes. Array size = 3300 * QCA_WLAN_VENDOR_ATTR_PNO_SET_LIST_PARAM_NUM_NETWORKS. 3301 */ 3302 QCA_WLAN_VENDOR_ATTR_PNO_SET_LIST_PARAM_EPNO_NETWORKS_LIST = 8, 3303 /* An array of 33 x unsigned 8-bit value; NULL terminated SSID */ 3304 QCA_WLAN_VENDOR_ATTR_PNO_SET_LIST_PARAM_EPNO_NETWORK_SSID = 9, 3305 /* Signed 8-bit value; threshold for considering this SSID as found, 3306 * required granularity for this threshold is 4 dBm to 8 dBm. 3307 */ 3308 QCA_WLAN_VENDOR_ATTR_PNO_SET_LIST_PARAM_EPNO_NETWORK_RSSI_THRESHOLD 3309 = 10, 3310 /* Unsigned 8-bit value; WIFI_PNO_FLAG_XXX */ 3311 QCA_WLAN_VENDOR_ATTR_PNO_SET_LIST_PARAM_EPNO_NETWORK_FLAGS = 11, 3312 /* Unsigned 8-bit value; auth bit field for matching WPA IE */ 3313 QCA_WLAN_VENDOR_ATTR_PNO_SET_LIST_PARAM_EPNO_NETWORK_AUTH_BIT = 12, 3314 /* Unsigned 8-bit to indicate ePNO type; 3315 * It takes values from qca_wlan_epno_type 3316 */ 3317 QCA_WLAN_VENDOR_ATTR_PNO_SET_LIST_PARAM_EPNO_TYPE = 13, 3318 3319 /* Nested attribute to send the channel list */ 3320 QCA_WLAN_VENDOR_ATTR_PNO_SET_LIST_PARAM_EPNO_CHANNEL_LIST = 14, 3321 3322 /* Unsigned 32-bit value; indicates the interval between PNO scan 3323 * cycles in msec. 3324 */ 3325 QCA_WLAN_VENDOR_ATTR_PNO_SET_LIST_PARAM_EPNO_SCAN_INTERVAL = 15, 3326 QCA_WLAN_VENDOR_ATTR_EPNO_MIN5GHZ_RSSI = 16, 3327 QCA_WLAN_VENDOR_ATTR_EPNO_MIN24GHZ_RSSI = 17, 3328 QCA_WLAN_VENDOR_ATTR_EPNO_INITIAL_SCORE_MAX = 18, 3329 QCA_WLAN_VENDOR_ATTR_EPNO_CURRENT_CONNECTION_BONUS = 19, 3330 QCA_WLAN_VENDOR_ATTR_EPNO_SAME_NETWORK_BONUS = 20, 3331 QCA_WLAN_VENDOR_ATTR_EPNO_SECURE_BONUS = 21, 3332 QCA_WLAN_VENDOR_ATTR_EPNO_BAND5GHZ_BONUS = 22, 3333 /* Unsigned 32-bit value, representing the PNO Request ID */ 3334 QCA_WLAN_VENDOR_ATTR_PNO_CONFIG_REQUEST_ID = 23, 3335 3336 /* keep last */ 3337 QCA_WLAN_VENDOR_ATTR_PNO_AFTER_LAST, 3338 QCA_WLAN_VENDOR_ATTR_PNO_MAX = 3339 QCA_WLAN_VENDOR_ATTR_PNO_AFTER_LAST - 1, 3340 }; 3341 3342 /** 3343 * qca_wlan_vendor_acs_select_reason: This represents the different reasons why 3344 * the ACS has to be triggered. These values are used by 3345 * QCA_WLAN_VENDOR_ATTR_EXTERNAL_ACS_EVENT_REASON and 3346 * QCA_WLAN_VENDOR_ATTR_EXTERNAL_ACS_CHANNEL_REASON 3347 */ 3348 enum qca_wlan_vendor_acs_select_reason { 3349 /* Represents the reason that the ACS triggered during the AP start */ 3350 QCA_WLAN_VENDOR_ACS_SELECT_REASON_INIT, 3351 /* Represents the reason that DFS found with the current channel */ 3352 QCA_WLAN_VENDOR_ACS_SELECT_REASON_DFS, 3353 /* Represents the reason that LTE co-exist in the current band. */ 3354 QCA_WLAN_VENDOR_ACS_SELECT_REASON_LTE_COEX, 3355 }; 3356 3357 /** 3358 * qca_wlan_vendor_attr_external_acs_policy: Attribute values for 3359 * QCA_WLAN_VENDOR_ATTR_EXTERNAL_ACS_EVENT_POLICY to the vendor subcmd 3360 * QCA_NL80211_VENDOR_SUBCMD_EXTERNAL_ACS. This represents the 3361 * external ACS policies to select the channels w.r.t. the PCL weights. 3362 * (QCA_WLAN_VENDOR_ATTR_EXTERNAL_ACS_EVENT_PCL represents the channels and 3363 * their PCL weights.) 3364 * @QCA_WLAN_VENDOR_ATTR_EXTERNAL_ACS_POLICY_PCL_MANDATORY: Mandatory to 3365 * select a channel with non-zero PCL weight. 3366 * @QCA_WLAN_VENDOR_ATTR_EXTERNAL_ACS_POLICY_PCL_PREFERRED: Prefer a 3367 * channel with non-zero PCL weight. 3368 * 3369 */ 3370 enum qca_wlan_vendor_attr_external_acs_policy { 3371 QCA_WLAN_VENDOR_ATTR_EXTERNAL_ACS_POLICY_PCL_PREFERRED, 3372 QCA_WLAN_VENDOR_ATTR_EXTERNAL_ACS_POLICY_PCL_MANDATORY, 3373 }; 3374 3375 /** 3376 * qca_wlan_vendor_channel_prop_flags: This represent the flags for a channel. 3377 * This is used by QCA_WLAN_VENDOR_EXTERNAL_ACS_EVENT_CHAN_INFO_ATTR_FLAGS. 3378 */ 3379 enum qca_wlan_vendor_channel_prop_flags { 3380 /* Bits 0, 1, 2, and 3 are reserved */ 3381 3382 /* Turbo channel */ 3383 QCA_WLAN_VENDOR_CHANNEL_PROP_FLAG_TURBO = 1 << 4, 3384 /* CCK channel */ 3385 QCA_WLAN_VENDOR_CHANNEL_PROP_FLAG_CCK = 1 << 5, 3386 /* OFDM channel */ 3387 QCA_WLAN_VENDOR_CHANNEL_PROP_FLAG_OFDM = 1 << 6, 3388 /* 2.4 GHz spectrum channel. */ 3389 QCA_WLAN_VENDOR_CHANNEL_PROP_FLAG_2GHZ = 1 << 7, 3390 /* 5 GHz spectrum channel */ 3391 QCA_WLAN_VENDOR_CHANNEL_PROP_FLAG_5GHZ = 1 << 8, 3392 /* Only passive scan allowed */ 3393 QCA_WLAN_VENDOR_CHANNEL_PROP_FLAG_PASSIVE = 1 << 9, 3394 /* Dynamic CCK-OFDM channel */ 3395 QCA_WLAN_VENDOR_CHANNEL_PROP_FLAG_DYN = 1 << 10, 3396 /* GFSK channel (FHSS PHY) */ 3397 QCA_WLAN_VENDOR_CHANNEL_PROP_FLAG_GFSK = 1 << 11, 3398 /* Radar found on channel */ 3399 QCA_WLAN_VENDOR_CHANNEL_PROP_FLAG_RADAR = 1 << 12, 3400 /* 11a static turbo channel only */ 3401 QCA_WLAN_VENDOR_CHANNEL_PROP_FLAG_STURBO = 1 << 13, 3402 /* Half rate channel */ 3403 QCA_WLAN_VENDOR_CHANNEL_PROP_FLAG_HALF = 1 << 14, 3404 /* Quarter rate channel */ 3405 QCA_WLAN_VENDOR_CHANNEL_PROP_FLAG_QUARTER = 1 << 15, 3406 /* HT 20 channel */ 3407 QCA_WLAN_VENDOR_CHANNEL_PROP_FLAG_HT20 = 1 << 16, 3408 /* HT 40 with extension channel above */ 3409 QCA_WLAN_VENDOR_CHANNEL_PROP_FLAG_HT40PLUS = 1 << 17, 3410 /* HT 40 with extension channel below */ 3411 QCA_WLAN_VENDOR_CHANNEL_PROP_FLAG_HT40MINUS = 1 << 18, 3412 /* HT 40 intolerant */ 3413 QCA_WLAN_VENDOR_CHANNEL_PROP_FLAG_HT40INTOL = 1 << 19, 3414 /* VHT 20 channel */ 3415 QCA_WLAN_VENDOR_CHANNEL_PROP_FLAG_VHT20 = 1 << 20, 3416 /* VHT 40 with extension channel above */ 3417 QCA_WLAN_VENDOR_CHANNEL_PROP_FLAG_VHT40PLUS = 1 << 21, 3418 /* VHT 40 with extension channel below */ 3419 QCA_WLAN_VENDOR_CHANNEL_PROP_FLAG_VHT40MINUS = 1 << 22, 3420 /* VHT 80 channel */ 3421 QCA_WLAN_VENDOR_CHANNEL_PROP_FLAG_VHT80 = 1 << 23, 3422 /* HT 40 intolerant mark bit for ACS use */ 3423 QCA_WLAN_VENDOR_CHANNEL_PROP_FLAG_HT40INTOLMARK = 1 << 24, 3424 /* Channel temporarily blocked due to noise */ 3425 QCA_WLAN_VENDOR_CHANNEL_PROP_FLAG_BLOCKED = 1 << 25, 3426 /* VHT 160 channel */ 3427 QCA_WLAN_VENDOR_CHANNEL_PROP_FLAG_VHT160 = 1 << 26, 3428 /* VHT 80+80 channel */ 3429 QCA_WLAN_VENDOR_CHANNEL_PROP_FLAG_VHT80_80 = 1 << 27, 3430 /* HE 20 channel */ 3431 QCA_WLAN_VENDOR_CHANNEL_PROP_FLAG_HE20 = 1 << 28, 3432 /* HE 40 with extension channel above */ 3433 QCA_WLAN_VENDOR_CHANNEL_PROP_FLAG_HE40PLUS = 1 << 29, 3434 /* HE 40 with extension channel below */ 3435 QCA_WLAN_VENDOR_CHANNEL_PROP_FLAG_HE40MINUS = 1 << 30, 3436 /* HE 40 intolerant */ 3437 QCA_WLAN_VENDOR_CHANNEL_PROP_FLAG_HE40INTOL = 1 << 31, 3438 }; 3439 3440 /** 3441 * qca_wlan_vendor_channel_prop_flags_2: This represents the flags for a 3442 * channel, and is a continuation of qca_wlan_vendor_channel_prop_flags. This is 3443 * used by QCA_WLAN_VENDOR_EXTERNAL_ACS_EVENT_CHAN_INFO_ATTR_FLAGS_2. 3444 */ 3445 enum qca_wlan_vendor_channel_prop_flags_2 { 3446 /* HE 40 intolerant mark bit for ACS use */ 3447 QCA_WLAN_VENDOR_CHANNEL_PROP_FLAG_HE40INTOLMARK = 1 << 0, 3448 /* HE 80 channel */ 3449 QCA_WLAN_VENDOR_CHANNEL_PROP_FLAG_HE80 = 1 << 1, 3450 /* HE 160 channel */ 3451 QCA_WLAN_VENDOR_CHANNEL_PROP_FLAG_HE160 = 1 << 2, 3452 /* HE 80+80 channel */ 3453 QCA_WLAN_VENDOR_CHANNEL_PROP_FLAG_HE80_80 = 1 << 3, 3454 }; 3455 3456 /** 3457 * qca_wlan_vendor_channel_prop_flags_ext: This represent the extended flags for 3458 * each channel. This is used by 3459 * QCA_WLAN_VENDOR_EXTERNAL_ACS_EVENT_CHAN_INFO_ATTR_FLAG_EXT. 3460 */ 3461 enum qca_wlan_vendor_channel_prop_flags_ext { 3462 /* Radar found on channel */ 3463 QCA_WLAN_VENDOR_CHANNEL_PROP_FLAG_EXT_RADAR_FOUND = 1 << 0, 3464 /* DFS required on channel */ 3465 QCA_WLAN_VENDOR_CHANNEL_PROP_FLAG_EXT_DFS = 1 << 1, 3466 /* DFS required on channel for 2nd band of 80+80 */ 3467 QCA_WLAN_VENDOR_CHANNEL_PROP_FLAG_EXT_DFS_CFREQ2 = 1 << 2, 3468 /* If channel has been checked for DFS */ 3469 QCA_WLAN_VENDOR_CHANNEL_PROP_FLAG_EXT_DFS_CLEAR = 1 << 3, 3470 /* Excluded in 802.11d */ 3471 QCA_WLAN_VENDOR_CHANNEL_PROP_FLAG_EXT_11D_EXCLUDED = 1 << 4, 3472 /* Channel Switch Announcement received on this channel */ 3473 QCA_WLAN_VENDOR_CHANNEL_PROP_FLAG_EXT_CSA_RECEIVED = 1 << 5, 3474 /* Ad-hoc is not allowed */ 3475 QCA_WLAN_VENDOR_CHANNEL_PROP_FLAG_EXT_DISALLOW_ADHOC = 1 << 6, 3476 /* Station only channel */ 3477 QCA_WLAN_VENDOR_CHANNEL_PROP_FLAG_EXT_DISALLOW_HOSTAP = 1 << 7, 3478 /* DFS radar history for slave device (STA mode) */ 3479 QCA_WLAN_VENDOR_CHANNEL_PROP_FLAG_EXT_HISTORY_RADAR = 1 << 8, 3480 /* DFS CAC valid for slave device (STA mode) */ 3481 QCA_WLAN_VENDOR_CHANNEL_PROP_FLAG_EXT_CAC_VALID = 1 << 9, 3482 }; 3483 3484 /** 3485 * qca_wlan_vendor_external_acs_event_chan_info_attr: Represents per channel 3486 * information. These attributes are sent as part of 3487 * QCA_WLAN_VENDOR_ATTR_EXTERNAL_ACS_EVENT_CHAN_INFO. Each set of the following 3488 * attributes correspond to a single channel. 3489 */ 3490 enum qca_wlan_vendor_external_acs_event_chan_info_attr { 3491 QCA_WLAN_VENDOR_EXTERNAL_ACS_EVENT_CHAN_INFO_ATTR_INVALID = 0, 3492 3493 /* A bitmask (u32) with flags specified in 3494 * enum qca_wlan_vendor_channel_prop_flags. 3495 */ 3496 QCA_WLAN_VENDOR_EXTERNAL_ACS_EVENT_CHAN_INFO_ATTR_FLAGS = 1, 3497 /* A bitmask (u32) with flags specified in 3498 * enum qca_wlan_vendor_channel_prop_flags_ext. 3499 */ 3500 QCA_WLAN_VENDOR_EXTERNAL_ACS_EVENT_CHAN_INFO_ATTR_FLAG_EXT = 2, 3501 /* frequency in MHz (u32) */ 3502 QCA_WLAN_VENDOR_EXTERNAL_ACS_EVENT_CHAN_INFO_ATTR_FREQ = 3, 3503 /* maximum regulatory transmission power (u32) */ 3504 QCA_WLAN_VENDOR_EXTERNAL_ACS_EVENT_CHAN_INFO_ATTR_MAX_REG_POWER = 4, 3505 /* maximum transmission power (u32) */ 3506 QCA_WLAN_VENDOR_EXTERNAL_ACS_EVENT_CHAN_INFO_ATTR_MAX_POWER = 5, 3507 /* minimum transmission power (u32) */ 3508 QCA_WLAN_VENDOR_EXTERNAL_ACS_EVENT_CHAN_INFO_ATTR_MIN_POWER = 6, 3509 /* regulatory class id (u8) */ 3510 QCA_WLAN_VENDOR_EXTERNAL_ACS_EVENT_CHAN_INFO_ATTR_REG_CLASS_ID = 7, 3511 /* maximum antenna gain in (u8) */ 3512 QCA_WLAN_VENDOR_EXTERNAL_ACS_EVENT_CHAN_INFO_ATTR_ANTENNA_GAIN = 8, 3513 /* VHT segment 0 (u8) */ 3514 QCA_WLAN_VENDOR_EXTERNAL_ACS_EVENT_CHAN_INFO_ATTR_VHT_SEG_0 = 9, 3515 /* VHT segment 1 (u8) */ 3516 QCA_WLAN_VENDOR_EXTERNAL_ACS_EVENT_CHAN_INFO_ATTR_VHT_SEG_1 = 10, 3517 /* A bitmask (u32) with flags specified in 3518 * enum qca_wlan_vendor_channel_prop_flags_2. 3519 */ 3520 QCA_WLAN_VENDOR_EXTERNAL_ACS_EVENT_CHAN_INFO_ATTR_FLAGS_2 = 11, 3521 3522 /* keep last */ 3523 QCA_WLAN_VENDOR_EXTERNAL_ACS_EVENT_CHAN_INFO_ATTR_LAST, 3524 QCA_WLAN_VENDOR_EXTERNAL_ACS_EVENT_CHAN_INFO_ATTR_MAX = 3525 QCA_WLAN_VENDOR_EXTERNAL_ACS_EVENT_CHAN_INFO_ATTR_LAST - 1, 3526 }; 3527 3528 /** 3529 * qca_wlan_vendor_attr_pcl: Represents attributes for 3530 * preferred channel list (PCL). These attributes are sent as part of 3531 * QCA_WLAN_VENDOR_ATTR_EXTERNAL_ACS_EVENT_PCL. 3532 */ 3533 enum qca_wlan_vendor_attr_pcl { 3534 QCA_WLAN_VENDOR_ATTR_PCL_INVALID = 0, 3535 3536 /* Channel number (u8) */ 3537 QCA_WLAN_VENDOR_ATTR_PCL_CHANNEL = 1, 3538 /* Channel weightage (u8) */ 3539 QCA_WLAN_VENDOR_ATTR_PCL_WEIGHT = 2, 3540 }; 3541 3542 /** 3543 * qca_wlan_vendor_attr_external_acs_event: Attribute to vendor sub-command 3544 * QCA_NL80211_VENDOR_SUBCMD_EXTERNAL_ACS. This attribute will be sent by 3545 * host driver. 3546 */ 3547 enum qca_wlan_vendor_attr_external_acs_event { 3548 QCA_WLAN_VENDOR_ATTR_EXTERNAL_ACS_EVENT_INVALID = 0, 3549 3550 /* This reason (u8) refers to enum qca_wlan_vendor_acs_select_reason. 3551 * This helps ACS module to understand why ACS needs to be started. 3552 */ 3553 QCA_WLAN_VENDOR_ATTR_EXTERNAL_ACS_EVENT_REASON = 1, 3554 /* Flag attribute to indicate if driver supports spectral scanning */ 3555 QCA_WLAN_VENDOR_ATTR_EXTERNAL_ACS_EVENT_IS_SPECTRAL_SUPPORTED = 2, 3556 /* Flag attribute to indicate if 11ac is offloaded to firmware */ 3557 QCA_WLAN_VENDOR_ATTR_EXTERNAL_ACS_EVENT_IS_OFFLOAD_ENABLED = 3, 3558 /* Flag attribute to indicate if driver provides additional channel 3559 * capability as part of scan operation */ 3560 QCA_WLAN_VENDOR_ATTR_EXTERNAL_ACS_EVENT_ADD_CHAN_STATS_SUPPORT = 4, 3561 /* Flag attribute to indicate interface status is UP */ 3562 QCA_WLAN_VENDOR_ATTR_EXTERNAL_ACS_EVENT_AP_UP = 5, 3563 /* Operating mode (u8) of interface. Takes one of enum nl80211_iftype 3564 * values. */ 3565 QCA_WLAN_VENDOR_ATTR_EXTERNAL_ACS_EVENT_SAP_MODE = 6, 3566 /* Channel width (u8). It takes one of enum nl80211_chan_width values. 3567 * This is the upper bound of channel width. ACS logic should try to get 3568 * a channel with the specified width and if not found, look for lower 3569 * values. 3570 */ 3571 QCA_WLAN_VENDOR_ATTR_EXTERNAL_ACS_EVENT_CHAN_WIDTH = 7, 3572 /* This (u8) will hold values of one of enum nl80211_bands */ 3573 QCA_WLAN_VENDOR_ATTR_EXTERNAL_ACS_EVENT_BAND = 8, 3574 /* PHY/HW mode (u8). Takes one of enum qca_wlan_vendor_acs_hw_mode 3575 * values */ 3576 QCA_WLAN_VENDOR_ATTR_EXTERNAL_ACS_EVENT_PHY_MODE = 9, 3577 /* Array of (u32) supported frequency list among which ACS should choose 3578 * best frequency. 3579 */ 3580 QCA_WLAN_VENDOR_ATTR_EXTERNAL_ACS_EVENT_FREQ_LIST = 10, 3581 /* Preferred channel list by the driver which will have array of nested 3582 * values as per enum qca_wlan_vendor_attr_pcl attribute. 3583 */ 3584 QCA_WLAN_VENDOR_ATTR_EXTERNAL_ACS_EVENT_PCL = 11, 3585 /* Array of nested attribute for each channel. It takes attr as defined 3586 * in enum qca_wlan_vendor_external_acs_event_chan_info_attr. 3587 */ 3588 QCA_WLAN_VENDOR_ATTR_EXTERNAL_ACS_EVENT_CHAN_INFO = 12, 3589 /* External ACS policy such as PCL mandatory, PCL preferred, etc. 3590 * It uses values defined in enum 3591 * qca_wlan_vendor_attr_external_acs_policy. 3592 */ 3593 QCA_WLAN_VENDOR_ATTR_EXTERNAL_ACS_EVENT_POLICY = 13, 3594 3595 /* keep last */ 3596 QCA_WLAN_VENDOR_ATTR_EXTERNAL_ACS_EVENT_LAST, 3597 QCA_WLAN_VENDOR_ATTR_EXTERNAL_ACS_EVENT_MAX = 3598 QCA_WLAN_VENDOR_ATTR_EXTERNAL_ACS_EVENT_LAST - 1, 3599 }; 3600 3601 /** 3602 * qca_wlan_vendor_attr_external_acs_channels: Attributes to vendor subcmd 3603 * QCA_NL80211_VENDOR_SUBCMD_EXTERNAL_ACS. This carries a list of channels 3604 * in priority order as decided after ACS operation in userspace. 3605 */ 3606 enum qca_wlan_vendor_attr_external_acs_channels { 3607 QCA_WLAN_VENDOR_ATTR_EXTERNAL_ACS_CHANNEL_INVALID = 0, 3608 3609 /* One of reason code (u8) from enum qca_wlan_vendor_acs_select_reason 3610 */ 3611 QCA_WLAN_VENDOR_ATTR_EXTERNAL_ACS_CHANNEL_REASON = 1, 3612 3613 /* Array of nested values for each channel with following attributes: 3614 * QCA_WLAN_VENDOR_ATTR_EXTERNAL_ACS_CHANNEL_BAND, 3615 * QCA_WLAN_VENDOR_ATTR_EXTERNAL_ACS_CHANNEL_PRIMARY, 3616 * QCA_WLAN_VENDOR_ATTR_EXTERNAL_ACS_CHANNEL_SECONDARY, 3617 * QCA_WLAN_VENDOR_ATTR_EXTERNAL_ACS_CHANNEL_CENTER_SEG0, 3618 * QCA_WLAN_VENDOR_ATTR_EXTERNAL_ACS_CHANNEL_CENTER_SEG1, 3619 * QCA_WLAN_VENDOR_ATTR_EXTERNAL_ACS_CHANNEL_WIDTH 3620 */ 3621 QCA_WLAN_VENDOR_ATTR_EXTERNAL_ACS_CHANNEL_LIST = 2, 3622 /* This (u8) will hold values of one of enum nl80211_bands */ 3623 QCA_WLAN_VENDOR_ATTR_EXTERNAL_ACS_CHANNEL_BAND = 3, 3624 /* Primary channel (u8) */ 3625 QCA_WLAN_VENDOR_ATTR_EXTERNAL_ACS_CHANNEL_PRIMARY = 4, 3626 /* Secondary channel (u8) used for HT 40 MHz channels */ 3627 QCA_WLAN_VENDOR_ATTR_EXTERNAL_ACS_CHANNEL_SECONDARY = 5, 3628 /* VHT seg0 channel (u8) */ 3629 QCA_WLAN_VENDOR_ATTR_EXTERNAL_ACS_CHANNEL_CENTER_SEG0 = 6, 3630 /* VHT seg1 channel (u8) */ 3631 QCA_WLAN_VENDOR_ATTR_EXTERNAL_ACS_CHANNEL_CENTER_SEG1 = 7, 3632 /* Channel width (u8). Takes one of enum nl80211_chan_width values. */ 3633 QCA_WLAN_VENDOR_ATTR_EXTERNAL_ACS_CHANNEL_WIDTH = 8, 3634 3635 /* keep last */ 3636 QCA_WLAN_VENDOR_ATTR_EXTERNAL_ACS_CHANNEL_LAST, 3637 QCA_WLAN_VENDOR_ATTR_EXTERNAL_ACS_CHANNEL_MAX = 3638 QCA_WLAN_VENDOR_ATTR_EXTERNAL_ACS_CHANNEL_LAST - 1 3639 }; 3640 3641 enum qca_chip_power_save_failure_reason { 3642 /* Indicates if the reason for the failure is due to a protocol 3643 * layer/module. 3644 */ 3645 QCA_CHIP_POWER_SAVE_FAILURE_REASON_PROTOCOL = 0, 3646 /* Indicates if the reason for the failure is due to a hardware issue. 3647 */ 3648 QCA_CHIP_POWER_SAVE_FAILURE_REASON_HARDWARE = 1, 3649 }; 3650 3651 /** 3652 * qca_attr_chip_power_save_failure: Attributes to vendor subcmd 3653 * QCA_NL80211_VENDOR_SUBCMD_CHIP_PWRSAVE_FAILURE. This carries the requisite 3654 * information leading to the power save failure. 3655 */ 3656 enum qca_attr_chip_power_save_failure { 3657 QCA_ATTR_CHIP_POWER_SAVE_FAILURE_INVALID = 0, 3658 /* Reason to cause the power save failure. 3659 * These reasons are represented by 3660 * enum qca_chip_power_save_failure_reason. 3661 */ 3662 QCA_ATTR_CHIP_POWER_SAVE_FAILURE_REASON = 1, 3663 3664 /* keep last */ 3665 QCA_ATTR_CHIP_POWER_SAVE_FAILURE_LAST, 3666 QCA_ATTR_CHIP_POWER_SAVE_FAILURE_MAX = 3667 QCA_ATTR_CHIP_POWER_SAVE_FAILURE_LAST - 1, 3668 }; 3669 3670 /** 3671 * qca_wlan_vendor_attr_nud_stats_set: Attributes to vendor subcmd 3672 * QCA_NL80211_VENDOR_SUBCMD_NUD_STATS_SET. This carries the requisite 3673 * information to start/stop the NUD statistics collection. 3674 */ 3675 enum qca_attr_nud_stats_set { 3676 QCA_ATTR_NUD_STATS_SET_INVALID = 0, 3677 3678 /* Flag to start/stop the NUD statistics collection. 3679 * Start - If included, Stop - If not included 3680 */ 3681 QCA_ATTR_NUD_STATS_SET_START = 1, 3682 /* IPv4 address of the default gateway (in network byte order) */ 3683 QCA_ATTR_NUD_STATS_GW_IPV4 = 2, 3684 3685 /* keep last */ 3686 QCA_ATTR_NUD_STATS_SET_LAST, 3687 QCA_ATTR_NUD_STATS_SET_MAX = 3688 QCA_ATTR_NUD_STATS_SET_LAST - 1, 3689 }; 3690 3691 /** 3692 * qca_attr_nud_stats_get: Attributes to vendor subcmd 3693 * QCA_NL80211_VENDOR_SUBCMD_NUD_STATS_GET. This carries the requisite 3694 * NUD statistics collected when queried. 3695 */ 3696 enum qca_attr_nud_stats_get { 3697 QCA_ATTR_NUD_STATS_GET_INVALID = 0, 3698 /* ARP Request count from netdev */ 3699 QCA_ATTR_NUD_STATS_ARP_REQ_COUNT_FROM_NETDEV = 1, 3700 /* ARP Request count sent to lower MAC from upper MAC */ 3701 QCA_ATTR_NUD_STATS_ARP_REQ_COUNT_TO_LOWER_MAC = 2, 3702 /* ARP Request count received by lower MAC from upper MAC */ 3703 QCA_ATTR_NUD_STATS_ARP_REQ_RX_COUNT_BY_LOWER_MAC = 3, 3704 /* ARP Request count successfully transmitted by the device */ 3705 QCA_ATTR_NUD_STATS_ARP_REQ_COUNT_TX_SUCCESS = 4, 3706 /* ARP Response count received by lower MAC */ 3707 QCA_ATTR_NUD_STATS_ARP_RSP_RX_COUNT_BY_LOWER_MAC = 5, 3708 /* ARP Response count received by upper MAC */ 3709 QCA_ATTR_NUD_STATS_ARP_RSP_RX_COUNT_BY_UPPER_MAC = 6, 3710 /* ARP Response count delivered to netdev */ 3711 QCA_ATTR_NUD_STATS_ARP_RSP_COUNT_TO_NETDEV = 7, 3712 /* ARP Response count delivered to netdev */ 3713 QCA_ATTR_NUD_STATS_ARP_RSP_COUNT_OUT_OF_ORDER_DROP = 8, 3714 /* Flag indicating if the station's link to the AP is active. 3715 * Active Link - If included, Inactive link - If not included 3716 */ 3717 QCA_ATTR_NUD_STATS_AP_LINK_ACTIVE = 9, 3718 /* Flag indicating if there is any duplicate address detected (DAD). 3719 * Yes - If detected, No - If not detected. 3720 */ 3721 QCA_ATTR_NUD_STATS_IS_DAD = 10, 3722 3723 /* keep last */ 3724 QCA_ATTR_NUD_STATS_GET_LAST, 3725 QCA_ATTR_NUD_STATS_GET_MAX = 3726 QCA_ATTR_NUD_STATS_GET_LAST - 1, 3727 }; 3728 3729 enum qca_wlan_btm_candidate_status { 3730 QCA_STATUS_ACCEPT = 0, 3731 QCA_STATUS_REJECT_EXCESSIVE_FRAME_LOSS_EXPECTED = 1, 3732 QCA_STATUS_REJECT_EXCESSIVE_DELAY_EXPECTED = 2, 3733 QCA_STATUS_REJECT_INSUFFICIENT_QOS_CAPACITY = 3, 3734 QCA_STATUS_REJECT_LOW_RSSI = 4, 3735 QCA_STATUS_REJECT_HIGH_INTERFERENCE = 5, 3736 QCA_STATUS_REJECT_UNKNOWN = 6, 3737 }; 3738 3739 enum qca_wlan_vendor_attr_btm_candidate_info { 3740 QCA_WLAN_VENDOR_ATTR_BTM_CANDIDATE_INFO_INVALID = 0, 3741 3742 /* 6-byte MAC address representing the BSSID of transition candidate */ 3743 QCA_WLAN_VENDOR_ATTR_BTM_CANDIDATE_INFO_BSSID = 1, 3744 /* Unsigned 32-bit value from enum qca_wlan_btm_candidate_status 3745 * returned by the driver. It says whether the BSSID provided in 3746 * QCA_WLAN_VENDOR_ATTR_BTM_CANDIDATE_INFO_BSSID is acceptable by 3747 * the driver, if not it specifies the reason for rejection. 3748 * Note that the user-space can overwrite the transition reject reason 3749 * codes provided by driver based on more information. 3750 */ 3751 QCA_WLAN_VENDOR_ATTR_BTM_CANDIDATE_INFO_STATUS = 2, 3752 3753 /* keep last */ 3754 QCA_WLAN_VENDOR_ATTR_BTM_CANDIDATE_INFO_AFTER_LAST, 3755 QCA_WLAN_VENDOR_ATTR_BTM_CANDIDATE_INFO_MAX = 3756 QCA_WLAN_VENDOR_ATTR_BTM_CANDIDATE_INFO_AFTER_LAST - 1, 3757 }; 3758 3759 enum qca_attr_trace_level { 3760 QCA_ATTR_TRACE_LEVEL_INVALID = 0, 3761 /* 3762 * Nested array of the following attributes: 3763 * QCA_ATTR_TRACE_LEVEL_MODULE, 3764 * QCA_ATTR_TRACE_LEVEL_MASK. 3765 */ 3766 QCA_ATTR_TRACE_LEVEL_PARAM = 1, 3767 /* 3768 * Specific QCA host driver module. Please refer to the QCA host 3769 * driver implementation to get the specific module ID. 3770 */ 3771 QCA_ATTR_TRACE_LEVEL_MODULE = 2, 3772 /* Different trace level masks represented in the QCA host driver. */ 3773 QCA_ATTR_TRACE_LEVEL_MASK = 3, 3774 3775 /* keep last */ 3776 QCA_ATTR_TRACE_LEVEL_AFTER_LAST, 3777 QCA_ATTR_TRACE_LEVEL_MAX = 3778 QCA_ATTR_TRACE_LEVEL_AFTER_LAST - 1, 3779 }; 3780 3781 /** 3782 * enum qca_wlan_vendor_attr_get_he_capabilities - IEEE 802.11ax HE capabilities 3783 */ 3784 enum qca_wlan_vendor_attr_get_he_capabilities { 3785 QCA_WLAN_VENDOR_ATTR_HE_CAPABILITIES_INVALID = 0, 3786 /* Whether HE capabilities is supported 3787 * (u8 attribute: 0 = not supported, 1 = supported) */ 3788 QCA_WLAN_VENDOR_ATTR_HE_SUPPORTED = 1, 3789 /* HE PHY capabilities, array of 3 u32 values */ 3790 QCA_WLAN_VENDOR_ATTR_PHY_CAPAB = 2, 3791 /* HE MAC capabilities (u32 attribute) */ 3792 QCA_WLAN_VENDOR_ATTR_MAC_CAPAB = 3, 3793 /* HE MCS map (u32 attribute) */ 3794 QCA_WLAN_VENDOR_ATTR_HE_MCS = 4, 3795 /* Number of SS (u32 attribute) */ 3796 QCA_WLAN_VENDOR_ATTR_NUM_SS = 5, 3797 /* RU count (u32 attribute) */ 3798 QCA_WLAN_VENDOR_ATTR_RU_IDX_MASK = 6, 3799 /* PPE threshold data, array of 8 u32 values */ 3800 QCA_WLAN_VENDOR_ATTR_PPE_THRESHOLD = 7, 3801 3802 /* keep last */ 3803 QCA_WLAN_VENDOR_ATTR_HE_CAPABILITIES_AFTER_LAST, 3804 QCA_WLAN_VENDOR_ATTR_HE_CAPABILITIES_MAX = 3805 QCA_WLAN_VENDOR_ATTR_HE_CAPABILITIES_AFTER_LAST - 1, 3806 }; 3807 3808 /** 3809 * enum qca_wlan_vendor_attr_spectral_scan - Spectral scan config parameters 3810 */ 3811 enum qca_wlan_vendor_attr_spectral_scan { 3812 QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_CONFIG_INVALID = 0, 3813 /* Number of times the chip enters spectral scan mode before 3814 * deactivating spectral scans. When set to 0, chip will enter spectral 3815 * scan mode continuously. u32 attribute. 3816 */ 3817 QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_CONFIG_SCAN_COUNT = 1, 3818 /* Spectral scan period. Period increment resolution is 256*Tclk, 3819 * where Tclk = 1/44 MHz (Gmode), 1/40 MHz (Amode). u32 attribute. 3820 */ 3821 QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_CONFIG_SCAN_PERIOD = 2, 3822 /* Spectral scan priority. u32 attribute. */ 3823 QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_CONFIG_PRIORITY = 3, 3824 /* Number of FFT data points to compute. u32 attribute. */ 3825 QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_CONFIG_FFT_SIZE = 4, 3826 /* Enable targeted gain change before starting the spectral scan FFT. 3827 * u32 attribute. 3828 */ 3829 QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_CONFIG_GC_ENA = 5, 3830 /* Restart a queued spectral scan. u32 attribute. */ 3831 QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_CONFIG_RESTART_ENA = 6, 3832 /* Noise floor reference number for the calculation of bin power. 3833 * u32 attribute. 3834 */ 3835 QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_CONFIG_NOISE_FLOOR_REF = 7, 3836 /* Disallow spectral scan triggers after TX/RX packets by setting 3837 * this delay value to roughly SIFS time period or greater. 3838 * u32 attribute. 3839 */ 3840 QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_CONFIG_INIT_DELAY = 8, 3841 /* Number of strong bins (inclusive) per sub-channel, below 3842 * which a signal is declared a narrow band tone. u32 attribute. 3843 */ 3844 QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_CONFIG_NB_TONE_THR = 9, 3845 /* Specify the threshold over which a bin is declared strong (for 3846 * scan bandwidth analysis). u32 attribute. 3847 */ 3848 QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_CONFIG_STR_BIN_THR = 10, 3849 /* Spectral scan report mode. u32 attribute. */ 3850 QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_CONFIG_WB_RPT_MODE = 11, 3851 /* RSSI report mode, if the ADC RSSI is below 3852 * QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_CONFIG_RSSI_THR, 3853 * then FFTs will not trigger, but timestamps and summaries get 3854 * reported. u32 attribute. 3855 */ 3856 QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_CONFIG_RSSI_RPT_MODE = 12, 3857 /* ADC RSSI must be greater than or equal to this threshold (signed dB) 3858 * to ensure spectral scan reporting with normal error code. 3859 * u32 attribute. 3860 */ 3861 QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_CONFIG_RSSI_THR = 13, 3862 /* Format of frequency bin magnitude for spectral scan triggered FFTs: 3863 * 0: linear magnitude, 1: log magnitude (20*log10(lin_mag)). 3864 * u32 attribute. 3865 */ 3866 QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_CONFIG_PWR_FORMAT = 14, 3867 /* Format of FFT report to software for spectral scan triggered FFTs. 3868 * 0: No FFT report (only spectral scan summary report) 3869 * 1: 2-dword summary of metrics for each completed FFT + spectral scan 3870 * report 3871 * 2: 2-dword summary of metrics for each completed FFT + 1x-oversampled 3872 * bins (in-band) per FFT + spectral scan summary report 3873 * 3: 2-dword summary of metrics for each completed FFT + 2x-oversampled 3874 * bins (all) per FFT + spectral scan summary report 3875 * u32 attribute. 3876 */ 3877 QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_CONFIG_RPT_MODE = 15, 3878 /* Number of LSBs to shift out in order to scale the FFT bins. 3879 * u32 attribute. 3880 */ 3881 QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_CONFIG_BIN_SCALE = 16, 3882 /* Set to 1 (with spectral_scan_pwr_format=1), to report bin magnitudes 3883 * in dBm power. u32 attribute. 3884 */ 3885 QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_CONFIG_DBM_ADJ = 17, 3886 /* Per chain enable mask to select input ADC for search FFT. 3887 * u32 attribute. 3888 */ 3889 QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_CONFIG_CHN_MASK = 18, 3890 /* An unsigned 64-bit integer provided by host driver to identify the 3891 * spectral scan request. This attribute is included in the scan 3892 * response message for @QCA_NL80211_VENDOR_SUBCMD_SPECTRAL_SCAN_START 3893 * and used as an attribute in 3894 * @QCA_NL80211_VENDOR_SUBCMD_SPECTRAL_SCAN_STOP to identify the 3895 * specific scan to be stopped. 3896 */ 3897 QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_COOKIE = 19, 3898 3899 QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_CONFIG_AFTER_LAST, 3900 QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_CONFIG_MAX = 3901 QCA_WLAN_VENDOR_ATTR_SPECTRAL_SCAN_CONFIG_AFTER_LAST - 1, 3902 }; 3903 3904 enum qca_wlan_vendor_tos { 3905 QCA_WLAN_VENDOR_TOS_BK = 0, 3906 QCA_WLAN_VENDOR_TOS_BE = 1, 3907 QCA_WLAN_VENDOR_TOS_VI = 2, 3908 QCA_WLAN_VENDOR_TOS_VO = 3, 3909 }; 3910 3911 /** 3912 * enum qca_wlan_vendor_attr_active_tos - Used by the vendor command 3913 * QCA_NL80211_VENDOR_SUBCMD_ACTIVE_TOS. 3914 */ 3915 enum qca_wlan_vendor_attr_active_tos { 3916 QCA_WLAN_VENDOR_ATTR_ACTIVE_TOS_INVALID = 0, 3917 /* Type Of Service - Represented by qca_wlan_vendor_tos */ 3918 QCA_WLAN_VENDOR_ATTR_ACTIVE_TOS = 1, 3919 /* Flag attribute representing the start (attribute included) or stop 3920 * (attribute not included) of the respective TOS. 3921 */ 3922 QCA_WLAN_VENDOR_ATTR_ACTIVE_TOS_START = 2, 3923 }; 3924 3925 enum qca_wlan_vendor_hang_reason { 3926 /* Unspecified reason */ 3927 QCA_WLAN_HANG_REASON_UNSPECIFIED = 0, 3928 /* No Map for the MAC entry for the received frame */ 3929 QCA_WLAN_HANG_RX_HASH_NO_ENTRY_FOUND = 1, 3930 /* Peer deletion timeout happened */ 3931 QCA_WLAN_HANG_PEER_DELETION_TIMEDOUT = 2, 3932 /* Peer unmap timeout */ 3933 QCA_WLAN_HANG_PEER_UNMAP_TIMEDOUT = 3, 3934 /* Scan request timed out */ 3935 QCA_WLAN_HANG_SCAN_REQ_EXPIRED = 4, 3936 /* Consecutive Scan attempt failures */ 3937 QCA_WLAN_HANG_SCAN_ATTEMPT_FAILURES = 5, 3938 /* Unable to get the message buffer */ 3939 QCA_WLAN_HANG_GET_MSG_BUFF_FAILURE = 6, 3940 /* Current command processing is timedout */ 3941 QCA_WLAN_HANG_ACTIVE_LIST_TIMEOUT = 7, 3942 /* Timeout for an ACK from FW for suspend request */ 3943 QCA_WLAN_HANG_SUSPEND_TIMEOUT = 8, 3944 /* Timeout for an ACK from FW for resume request */ 3945 QCA_WLAN_HANG_RESUME_TIMEOUT = 9, 3946 /* Transmission timeout for consecutive data frames */ 3947 QCA_WLAN_HANG_TRANSMISSIONS_TIMEOUT = 10, 3948 /* Timeout for the TX completion status of data frame */ 3949 QCA_WLAN_HANG_TX_COMPLETE_TIMEOUT = 11, 3950 /* DXE failure for TX/RX, DXE resource unavailability */ 3951 QCA_WLAN_HANG_DXE_FAILURE = 12, 3952 /* WMI pending commands exceed the maximum count */ 3953 QCA_WLAN_HANG_WMI_EXCEED_MAX_PENDING_CMDS = 13, 3954 }; 3955 3956 /** 3957 * enum qca_wlan_vendor_attr_hang - Used by the vendor command 3958 * QCA_NL80211_VENDOR_SUBCMD_HANG. 3959 */ 3960 enum qca_wlan_vendor_attr_hang { 3961 QCA_WLAN_VENDOR_ATTR_HANG_INVALID = 0, 3962 /* Reason for the hang - u32 attribute with a value from enum 3963 * qca_wlan_vendor_hang_reason. 3964 */ 3965 QCA_WLAN_VENDOR_ATTR_HANG_REASON = 1, 3966 3967 QCA_WLAN_VENDOR_ATTR_HANG_AFTER_LAST, 3968 QCA_WLAN_VENDOR_ATTR_HANG_MAX = 3969 QCA_WLAN_VENDOR_ATTR_HANG_AFTER_LAST - 1, 3970 }; 3971 3972 #endif /* QCA_VENDOR_H */ 3973